USB cable for printer C6200 all-in-one

Similar Questions

• Connect the USB cable on my 5510e-all-in-one wireless HP Photosmart printer

  Need me 15 minutes to print a page using my network wireless at home. I decided to connect the printer with a USB cable, but the installation of HP - written installation guide - instructions only show the USB wireless method. I already bought a SPEAKER cable so I'm readt to go one time that I get help. My laptop, that I intend to connect is a dp4 Pavilion from HP with Vista. Thank you.

  Hi there billham68 and welcome to the printer HP consumer Forums.

  Here is a link that should help you in the accomplishment of the task at hand.

  Installation of the software of the printer in Windows for a USB cable connection

  http://support.HP.com/us-en/document/c03521864

• UBS cable for Photosmart e6520 all-in-One printer

  Can I use USB cable my old printer to the HP Photosmart all-in-One e-6520? My old printer was not a wireless printer.

  USB cables are standard, you should have no problems.  Don't you have a wireless router? There are advantages to set up the printer on a network, rather than directly connected by USB.

• USB cable for printer HP Envy 5530

  A USB cable is available for the printer All in 5530 want? If so, and what type is?

  Hello

  Normal USB cable: Standard-A plug (PC connection), Standard-B plug (printer connection).

• USB cable for printer HP Photosmart C5280

  Sorry for the question "stupid"...

  We have lost the cable that connects the printer to the macBook. Can you tell me what are the specs, so I can find one online? Thank you!

  Here's another cable on Amazon:

  http://www.Amazon.com/Belkin-hi-speed-USB-cable-feet/DP/B00004Z5M1

  You must be able to an electronic retailer (Best Buy, Wal-Mart, Target) and pick one up. Make sure the ends to resemble the one on the Amazon page.

• USB cable for printer HP

  Bought a printer there are 4 years, but never out of the box because I didn't have to replace the old printer (solved driver problem).  The 'new' printer is a HP Deskjet 3915.  Just opened the box to install it and found that it was not the USB cable (instructions stated that the cable may not be included).  I have several USB cables, but none that has an end that would fit in the HP printer.

  I looked on the sites internet/HP printer and he never gave no specific information on the cable... said just a USB 'standard' preference under 3 feet long.   I found also the instructions to install the drivers for this printer model, but the information does not include Windows 7.

  So my questions are: is there a standard USB cable that fits all HP printers, that I must ask a compatible HP printer USB cable?   I have to perform a control more to determine if this printer work with windows 7?

  Solved!  Called BestBuy and found that the answer to my question USB: more "printer" USB cables are equipped with a standard connection with the printer.  Also, did a search on the internet and found that Windows 7 includes a driver for the printer HP deskjet 3915 color.

  After a trip to BB, my new printer (4 year) is running.

• Scanning for printer e-all-in-one HP 6510

  I'm used to be able to scan from my printer to my computer.  Now it can "see" it. When I press the icon of the computer, I get a message that says, "To ensure that the printer software is installed on your computer, and that 'The analysis of the computer' is enabled via the printing software".

  So my question is, ' how can I activate?  I am able to print from my computer to my printer.  I have a new computer HP with Windows 8.  I had to download the software from a link on this site to allow printing.

  Also, I always have to use the Assistant configuration to my computer to print. I don't have to do it when I got to the computer.  Is there a way to fix this too

  brtoconnor wrote:

  So my question is, ' how can I activate?  I am able to print from my computer to my printer.  I have a new computer HP with Windows 8.  I had to download the software from a link on this site to allow printing.

  Hello

  Please, try the following steps:

  • Click the icon of the printer on the desktop,
  • Click Manage scan of the computer,
  • Click Activate.

  You can activate it at Windows startup. You may have run the following utility to fix this problem:

  http://ftp.HP.com/pub/softlib/software12/COL44840/MP-109033-2/hppiw.exe

  Kind regards.

• Re - install the software for the printer C6280 all in one... get a "file not found" error message

  you need to reinstall the software for the printer c6280 all-in-one. Downloaded the last installation on HP web site package. During the installation process I get an error message... Unable to find user/appdata/local/temp/7z256315/setup/...setup/blocksysuser...

  the 7z256315 folder does not exist on the hard disk.

  I also have a message that it cannot find PS_A10_02_software.msi.

  Windows 7, C6280 printer all-in-one. Printer is connected to the router. The desktop computer is connected via an ethernet cable, the laptop/ipad/iphone/internet radio are connected via the wireless to the router.

  I hope you can help

  Thank you

  Charlie

  Hi cberistain,

  Follow the steps below and let me know what happens?

  First step: clear temp directory

  1. Type %temp% term or search programs and files of field
  2. Select all the files in this folder, and then press the delete key to remove. If you receive a message that the file is in use, you will need to ignore this file (s).
  3. Proceed to step 2 below

  Second step: downloaded and extracted to your system:

  1 download the drivers and full software features

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=MP-77039-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 3645097 & sw_lang=.

  2. once the download is complete, double-click the file to extract the software.

  3. when the installation window opens, press the Cancel button to stop the installation

  4. tap folder in the race or search programs and files of field

  5. Locate and open the folder starting with 7z (example: 7zS2356)

  6. right click on the folder and select copy

  7. close this window and all open windows, and then in the Middle the desktop right click your mouse and select Paste. This will move the 7z folder on your desktop.

  8 open the 7z, that you just copied on your desktop

  9 open the Util folder

  10 open the CCC folder

  11 start the uninstall_L4

  12. once the uninstall is complete, restart the computer

  13. run disk cleanup from the tools Accessories\ system under all programs folder

  14. download and install the latest version of Adobe flash player

  http://www.Adobe.com/support/flashplayer/downloads.html

  15 open the 7z folder and then double-click the Setup.exe file that will be towards the bottom of the open window. Follow the instructions on the screen to reinstall your printer.

  Let me know if you are able to successfully install the software and driver and are able to print and scan?

• Owners of printer inkjet all-in-one Dell 962 thread (W7)

  Please follow the instructions below and then tell me what happens.

  Make sure that your computer has the latest Windows updates, especially of .net framework, necessary to run many applications and the latest Java.

  Unplug your printer.

  Download and run this patch to completely remove the printer from your computer. Run the fix, a MUST on Vista machines, until it prompts you to restart your computer.

  If you use Windows 7 also try... Driver Manual printer removal

  Restart your computer.

  Download the correct drivers.

  XP drivers

  Vista 32-bit drivers

  All other drivers

  Vista 64-bit drivers

  Install the appropriate drivers. You will be asked when connect you your printer (power on)

  To install the drivers, sometimes the file decompresses and does nothing. You must find the setup.exe file, right-click on it, then on the left click on run as administrator *.

  If you use Windows 7, use the Vista drivers in compatibility mode.

  Right click on the file setup.exe, on the left, click Properties, compatibility of the left click. Replace the Vista compatibility (try Vista SP2). Then, install the appropriate drivers. You will be asked when connect (printer)

  To install the drivers, sometimes the file decompresses and does nothing. You must find the setup.exe file, right-click on it, then on the left click on run as administrator *.

  In the digitization, if you have the disc that came with the printer, and then insert the floppy disk to the printer and keep it from running. Go to my computer and double-click it. Locate the drive that contains the disk Dell inside. Right-click on it, left click Explore. Find the folder of the OCR. In the OCR folder, there is a folder of Abbyy. Right click on setup.exe, which is located in the folder Abbyy and left, click Run as administrator. This will install the OCR program.

  Scanning

  Scan using the USB connection, open the Dell all-in-one Center, click on the scan and copy and scan from there.

  Scan wireless, use the buttons to scan on the printer.

  Rick

  Rick,

  Thank you much for the help. I took your advice and installed the Vista SP2 drivers in compatibility mode, and when my laptop is connected to the printer via a USB cable, I can print.  Now, here's the best... Later, I decided to have the printer put in place for the wireless.

  I tried to add a Dell network port, and then pass.  Did not work.  I tried also to add another printer by pointing to a shared printer on an XP computer.  I noticed one thing, it is that when the Dell printer software installed and prompted me to plug the printer into my USB port, it appeared that Windows snuck into another driver.  I saw a message saying that the printer was ready before the Dell software were made.  I also noticed that when I tried to create a new Dell printer two print drivers were available.

  In any case, I followed your instructions to uninstall everything (ran program of uninstalling the Dell software, rebooted, ran the patch to clean, restarted), then ran the Dell program configuration of the software (in compatibility mode Vista x 64 SP 2) and chose an installation over the network instead of local installation. He saw the Dell printer on USB wireless adapter and installed fine.  Now, everything seems to work wireless.

  I guess my point of view for writing is to warn that when you plug the USB cable during installation of Dell, it seems that Windows 7 is going to sneak in another pilot.  I also advise to install over the network if you want to try to use it wireless, rather than starting with the local USB installation and hope to switch to a network port later.  Thanks again for your message.

• HP psc 1210 printer v all-in-one

  I'm missing a driver for my hp psc 1210 printer v all-in-one.

  I can't print from my desktop pc to Windows 7 on my printer.

  Printer works very well to plug into the wall for printer - will make copies just fine.

  Computer added my default printer - that part is fine.

  When I try to print from the computer to the printer, I get a message saying the printer is waiting for 1 document waiting to print, but it will not be printed.

  I tried to unplug the USB cable and plug it into another USB port, but it does not work either.

  Tried the Printing Troubleshooter?
  http://Windows.Microsoft.com/en-in/Windows7/open-the-printer-Troubleshooter
  If this does not help, try this procedure by Arthur Li [MSFT]:
  Clear printer spooler files and activate the Spooler Service
  =================================
  1. click on start, type "Services.msc" (without the quotes) in the search box and press ENTER.
  2. double-click on "Printer Spooler" in the Services list.
  3. click on stop, and then click OK.
  4. click on start, type "% WINDIR%\system32\spool\printers" in the search box and press ENTER, remove all files in this folder.
  5. click on start, type "Services.msc" (without the quotes) in the search box and press ENTER.
  6 double click on "Printer Spooler" in the Services list.
  7. click on start. In the Startup Type list, make sure that "Automatic" is selected and click OK.

• What should I buy to re - install my printer Dell all-in-One A960 Windows 8 after Windows XP?

  My printer Dell all-in-One (purchases. 2004) has stopped working.  When you try to use, sign popped up "print spooler service does not work? This has happened a month after that I switched to Windows 8.  Dell said there is no software for this printer be re-installed Windows 8 and suggested that I buy a different printer.

  I don't think that Dell should have the last word.  Any advice?  Can I buy drivers, other software?

  Thanks for your information.

  I suggest to try this:

  (1) unplug the printer from the power point

  (2) connect one end of the USB cable to the printer (if it is not already connected)

  (3) connect the other end to the machine using any free USB port

  (4) turn the printer by plugging the power plug

  (5) look at the screen to see if Windows indicates all compatible drivers

  If this does not work then try to look for Windows7 or even Windows Vista drivers and then install. However, make sure that these drivers are from the DELL website if possible)

  Good luck and hope it works.

• PSC 1350 all-in-one: HP Director for PSC 1350 all-in-one - using Windows 10 (64-bit)

  Hello!  I recently had a new hard drive installed on my Samsung laptop year-and-a-half-year-old, as well as 10 (64-bit) Windows as well. Instead of using the original installation disc for my printer range all-in-one HP psc1350 (bought 1/2004), I have used your site and just did a download tonight HPPIW. EXE .  My question is: I do not see the original HP Director on the desktop now after the above file download. The copying, printing, scanning are all working well, if that's fine! So all the "Director" now wonder, if I can get in a way that - since the original my installation disc or HP support Web site? Thank you, CR-Issquah (26/08/2015, 21:00 - PT)

  Hello

  HP Director has been supported only for your printer up to Windows XP, since Windows Vista full features software is no longer available for your printer, and there is no HP Director application or provided HP solutions Center.

  You can follow the following document which lists no available workaround solution and the limitation of the provided solution:

  http://support.HP.com/us-en/document/c04740294

  Shlomi

• Installation printer A920 all-in-one

  I just bought a used, refurbished OptiPlex 755 PC with Win 7 OS and am trying to install my all-in-One A920 printer. This is the printer that came with (my Dell Dimension 2400 series) desktop I bought about 7 years ago. I downloaded and installed (or so I thought) a Vista 64 bit driver I've read on the Dell website is supposed to be compatible with my Windows 7 64-bit OS. I plugged my printer and opens the file. I thought it was going to guide me through the process of setting up, but he did not. My computer recognized my printer, and he let me even in the all-in-one program. I was able to scan a document in color (but it wouldn't let me save it), I was unable to copy or print documents, and the "empty cartridge" box came up saying that black inkjet cartridges and color were empty; they are not empty because I recently replaced both cartridges. I miss any step, or not to do something in the right order? The printer does not give me a lick of problems on my Dell PC with Windows XP. I don't want to have to buy another printer, if possible, any help you can give me would be appreciated! Thank you! p.s. I have not loaded MS word on my new computer, so I wonder if this has nothing to do with the printer does not. (??)

  monksplay,

  The procedure is listed below. The OCR program, found on the disc from the printer, is required for scanning documents and fax.

  First run, delete print jobs to eliminate any print job stuck in the queue.

  Unplug the printer.

  Download and run the patch (cleaning printer utility) until it prompts you to restart your computer.

  Restart your computer. Make sure that the printer is deleted. Driver Manual printer removal

  Download the 32-bit drivers for Vista for Windows 7 32-bit or 64-bit drivers for Windows 7 64 bit Vista. Install the Vista drivers in Vista compatibility mode, you will get a message, the printer is not connected. Connect the printer at the moment (power on).

  You will find links to the patch/drivers to...

  Owners of printer inkjet all-in-one Dell A920 thread (W7)

  Don't forget the programs anti-virus and firewall will block communications.

  In the digitization, if you have the disc that came with the printer, and then insert the floppy disk to the printer and keep it from running. Go to my computer and double-click it. Locate the drive that contains the disk Dell inside. Right-click on it, left click Explore. Find the folder of the OCR. In the OCR folder, there is a folder of Abbyy. Right click on setup.exe, which is located in the folder Abbyy and left, click Run as administrator. This will install the OCR program.

  Rick

• where can I buy a usb cable for pc vcr2 ion?

  I need to buy a usb cable for my ion vcr 2 pc

  No matter what computer or electronics store or online.

  Just make sure you have good connectors at each end, all type 2 and "gender".  The end that connects to the computer is called a Type A.  The plug that connects to the device vcr2pc may be a Type A, a mini-B, or (unlikely) a micro-B.

  

  For example--> http://www.newegg.com/Product/ProductList.aspx?Submit=ENE&N=100016767%20600020249&IsNodeId=1&Description=usb%20cable&name=USB%202.0&Order=BESTMATCH

• Cannot find driver for HP 2710 all-in-one anywhere that works.

  I read the questions / answers on the printer drivers for my new laptop with Windows 7 and it seems that nothing is exhists for my HP 2710 all-in-one.   The driver that Windows only supports the printer, not the scanner or fax.  Many answers recommend to contact HP for the pilot, but HPs response is to use that Microsoft has in the computer.

  I don't know why Microsoft Gets a complete driver for this popular all-in-one printer.  My new Mac Book in their OS and it will interface with all functions beautifully.  He finds the printer, scanner and fax and installed the flawless drivers.   Now that I bought a PC even once, it's frustrating to find that Microsoft has yet to produce a stable product compatible XP that was at least good support with software companies and hardware.   Should I really buy all new software and equipment to own a PC these days?

  Just in case where you were not already in the running of it here is a link to HP described as workaround to make the scanner and fax from the HP 2710 works with the driver included in Windows 7:http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01796736&lc=en&dlc=en&cc=us&os=4062&product=420428&sw_lang=&key=null&site=null#N341