USB disabling on PXI controllers

Similar Questions

• Windows failed to update for HP - Bus USB and Ports, display controllers - HP w2408 widescreen LCD

  I have a new HP M9402 desktop with monitor Hp W2408 Summit.  I get a message to update windows for HP - Bus USB and Ports, display controllers - ACL from HP w2408 widescreen, but the windows download always fails.  I tried several times to download this update.

  Any help would be greatly appreciated.

  Hi all

  The solution to my problem of not being able to make updates to the window was to spend in an HDMI instead of VGA cable.

  BR / / JJG

• Automatic update does not install 'ViewSonic - Bus USB and Ports, display controllers - ViewSonic VP2365WB.

  Windows update - AutoUpdate does not install 'ViewSonic - Bus USB and Ports, display controllers - ViewSonic VP2365WB. Any ideas? Thank you.

  Original title: Bus USB and Ports, display - ViewSonic VP2365WB controllers

  Windows update - AutoUpdate does not install 'ViewSonic - Bus USB and Ports, display controllers - ViewSonic VP2365WB. Any ideas? Thank you.

  Hide and unless the material was manufactured by Microsoft or the hardware manufacturer tells you that you should get the driver FROM Microsoft - do not install Microsoft device for material non-Microsoft drivers.

• How knowledge usb disable any software?

  How knowledge usb disable any software?

  Hello Amol,

  From your description, it seems you want to know how to disable the use of USB devices to a computer using any software. If not what I understood, please let us know and explain your problem in detail.

  In some versions of Windows 7, we have a feature called Group Policy Editor. This feature could be used to configure various Windows system components, including the deactivation of USB devices. But support for the Group Policy Editor will be the best in the Windows 7 IT Pro TechNet forums. I provide you the link le lien to this forum below, please create a new thread in there if you want to disable the USB devices using the Group Policy Editor:

  http://social.technet.Microsoft.com/forums/en-us/category/w7itpro

  Hope this information helps. Let us know if you need help with Windows.

• USB disabled not able to write and read access but user authorized to datacard possible

  Dear all,

  I need usb disabled unable to access both read & write. But able to access a Data card and USB mouse.  This is possible thanks to a block log. Please post your suggestion.

  Hello

  1. What is the exact problem you are facing with USB?

  2. you receive an error message?

  3. have you made changes on the computer before this problem?

  Please provide us with more information to help you further.

• USB disabled after the update of the Sierra (a short circuit and a work)

  Hi, when I bought my mbp 13 inches mid2012 (used, not new) I noticed that a USB port did not work. In the Yosemite sometimes I noticed that a USB port consumed too much energy and have been disabled. (I think because the usb port has been short-circuited. Year when it was time to update the mbp to El Capitan I had a few panic the kernel and the newspaper was shown as the last driver loaded the USB driver, so I kept the mbp with Yosemite. A few days ago, I updated for Sierra but only usb which used to work stopped working. It has enabled and turned on but Finder and disk utility does not see the drive. In an Apple dealer they said that could be established relationships with some oxide and next week will take it and see what the problem is.

  If there is someone with the same problems, please tell me what to do! I don't want to put in the trash my mac just for a flash drive... but I need!

  Hi Supermene,

  Thank you for using communities of Apple Support. Based on what you said, it appears as a USB device is not recognized in one of the USB ports. There are a few things that can cause this. I recommend you read these articles, which may be able to help solve the problem.
  

  macOS Sierra: If a USB device does not work

  Reset the management system (SCM) controller on your Mac.

  See you soon.

• Satellite A210-1AH - USB conflict pci bus controllers resource at startup

  Hello

  I have a Toshiba Satellite A210-1AH
  model without PSAFGE-05X01GDU

  When I start the laptop after the toshiba logo. The laptop gives the following error:

  Bus ERROR USB controller resources conflict pci on the motherboard
  Bus: 14, device: 06, function: 00

  Bus ERROR USB controller resources conflict pci on the motherboard
  Bus: 14, device: 06, function: 01

  Bus ERROR USB controller resources conflict pci on the motherboard
  Bus: 14, device: 06, function: 02

  Bus ERROR USB controller resources conflict pci on the motherboard
  Bus: 14, device: 06, function: 03

  Bus ERROR USB controller resources conflict pci on the motherboard
  Bus: 14, device: 06, function: 04

  Press F1 to load the default values, F2 for Setup

  I tried:
  -load the default values
  -disconnect the dvd player, hard disks, memory
  -disable the hardware in the bios

  Can someone help me?

  PS. I can't find this model on the driver here, to download a bios update.
  This model is not longer supported?

  Ronald

  Hello

  You can enter the BIOS settings? If you can do this by using F2 to start together to check and default settings if the same thing will happen again. You can try to put the bootable disc in ODD and try to check if you have access to the HARD drive.

  If the same thing will happen again and again I'm afraid the motherboard is a failure of m.

• A USB from a PXI power control, turn the engine in real time

  Hello

  I need a USB of my target in time power control real (PXI) who installed the engine time real Labview (no windows installation).

  If I'm not mistaken, this is not possible with the USB port on the controller (NI PXI-8108) that I have not installed windows to recognize the device.  As far as I could see, it looks like I need to buy a special card for PXI that allows me to interact with USB devices.

  Is there someone who came across such an environment to see if it's the right approach?

  Thank you very much

  Dani

  

  For those who are interested, in order to control the USB equipment, the following requirements is necessary for a Phar Lap ETS RT OS operating system:

  In time real LabVIEW 2011 or higher
  VISA, 5.1 or higher

  http://digital.NI.com/public.nsf/allkb/5F30CD20D4D986CC862576CF00748B15

  http://digital.NI.com/public.nsf/allkb/ED3790E56FE969F8862575C30076063C?OpenDocument

  The upgrade of the system and the second link will allow such equipment.

  

• Derives from the system time when calling OR-Motion screw on PXI controllers

  Hello

  Just an email to avoid others wasting time when they are facing in this fantasy bug:

  We use PXI systems with Controllers NI PXI running Windows 7 and the 7340 family cards (PXI-7344). We have noticed that when the calls when it's through screws OR-Motion to question the different registers of the State (e.g. position, ADC value, general axis or the reference state) axis, the (Windows) system clock runs FASTER either. OR-Motion calls most are performed per second, faster windows clock works. When you get into the status for 4 axes 10 times per second (lines 100 ms rate), the drift is greater than 5%!

  I include here an example of program that reproduces this behavior.

  It is an essential question, for example if save you data with or from the timestamps, and it gets even worse if Windows is configured to periodically synchronize its own clock to a server via the NTP Protocol (it's how we noticed this problem in the first place). In this case, you see large discontinuities in your data every once in a while. Our systems must be running automatically and record data continuously throughout the year, so this bug is a real challenge.

  People at NOR been able to reproduce this bug too and are working on it (no idea of any CAR # yet). Note that this problem has not been seen on a DC non - OR Office running Windows 7 64 bit...

  The exact configuration is the following:

  Chassis PXI-1036

  PXI-8101 (or PXI-8102 on another system) controller

  4 PXI-7340 axes into the Groove 4, no physical connection for this test

  (PXI-6221 in slot 2, not used in this sample program)

  Windows 7 Enterprise SP1 32-bit English

  LabVIEW 2011 SP1 32-bit English

  OR-Motion 8.3

  2.6.2 PXI platform services

  (all software OR additional distribution 2012 DS1)

  Controller BIOS: improved 1.3.1 to 2.0.1f0, problem given the two versions of the BIOS

  I'll try to post here as soon as we receive news of NEITHER.

  Kind regards

  Vincent

  Hi all

  I wanted to let you know that the driver OR Motion 8.4 coming should solve this problem.

  Best regards

• input device touchscreen usb disabled and now the device disappeared

  To summarize for those who want a short version:

  Model: Sony VAIO Duo svd11225cxb

  Windows 8.1

  a. my touch screen of this device is * outside? Any way to reinstall the driver for the touch screen? Tech Sony said that the material is very good.

  b. in my efforts to solve the problem, I turned off a device in Device Manager and it now gone, no way to recover?

  Here is the full version:

  I have a Sony VAIO Duo svd11225cxb. After the recent updates, freaked out and kept touch screen back to the menu screen to start (and possibly other areas of the screen).

  We decided that so that the computer to operate, it should disable the touch screen. So we went to the Device Manager and disabled the "usb input device" under "human interface devices" which associated with the touch screen. Allow us went then back to him and found that the unit had disappeared from the Device Manager. I tried to install the next window touchscreen driver, but that did nothing. Any advice?

  Hi herschen,.

  Welcome to the community of Sony!

  Perhaps the question is just the driver. We will isolate the problem by following these steps:

  • Power cycle - turn off the laptop-> flip the unit and look for a button cell or a pin hole on the bottom of the laptop. Using a safety pin, press and hold the hole for 5 seconds.

  

  • Reset the BIOS to the
  • Go to Device Manager -> right click and Uninstall the driver/s under Human Interface Device (DO NOT REMOVE). Then restart the unit. The driver will be reinstalled.
  • Run the Windows Update and Vaio Update.

  Hope these helps.

  Kind regards

  Vincent

  If my post answered your question, please mark it as "accept as a Solution.

• Problems of allocation of resources motherboard PCI with PXI controllers

  I set up a test system to a PXI-PCIe8361 controller and a PXI-1042 chassis.  Several years ago, there are known problems with some motherboards on the assignment of the PCI resources.  I looked and could not find more old messages and lists of recommended motherboards.  It seems that ASUS is a manufacturer in order to avoid any Abit and Gigabyte function well.  Is there a list more up-to-date recommended motherboards or manufacturers?  Is it still a problem with the latest motherboards?

  Any information will be appreciated,

  Nick

  Hi Nick,

  PCI resource allocation issues are significantly less common with new mothers/BIOS maps. In situations where this problem always produces a BIOS update usually solves the problem. The best advice I can give if you buy a new computer for connection of MXI must go with a PC and a cell phone, who you are.

  These question is sufficiently rare that we do not maintain a list of manufactures suggested, if you encounter any problems you can call us at the 1-866-ASK-MYNI, and we would be happy to help you.

  Thank you

  Scott M.

• OR PXI-8196 target using a USB stick formatting

  Hello everyone,

  I use a PXI chassis with controller PXI-8196 and multiple PXI DAQmx cards. I need to format the hard drive on the target of PXI and reinstall the RT operating system as well as all other software. I am trying to restart the PXI with a USB bootable, but it gives me the option to format the hard drive.

  Here are the steps I followed.

  1. I created the disk bootable with MAX using the RT disc utilities > create Desktop PC USB Drive Utility (PXI-8196 does not have a floppy drive so I have to use a USB key)

  2. I have connected a keyboard and screen to target to see it start.

  3. I've also adjusted the sequence of boot as the boot option "USB HDD: LEXAR JUMPDRIVE SPORT" among those available in the boot sequence has the highest priority. (My USB is a USB of LEXUS so I'm sure that this particular option must be the first in the sequence).

  4 but once I start my system. It does not give me the option to format (according to MAX documentation should give me an option to "format hard drive"). Here's what I see on the screen connected to the target

  = = The output to the screen is bounded by these two rails =.

  Boot mode safe of Romans...

  Enter safe mode.

  The IP address is: 10.10.10.2

  _

  ===========================================================================

  At the end of the last cursor keeps blinking and nothing happens

  5. the 10.10.10.2 IP address is the address in the configuration I want to format and reinstall. So I don't know if he meant to keep automatically previous IP address.

  6. to avoid the fact that there may be something wrong with the USB, I repeated the procedure as a whole with another USB drive. But exactly the same thing happens again.

  Please help me it reboot with a USB port and format the hard drive and reinstall all software.

  Thanking in anticipation.

  Vivek.

  Hello

  Try this, go into the BIOS of the PXI, under LabVIEW RT to the startup configuration, change the Windows option / other OS. Then try what you are doing.

  Let me know if it works for you

• For the USB Hi-Speed and Licensing policy GPIB controller

  Hello

  I wanted to confirm understanding licensing NI VISA.

  If I use the GPIB controller OR to the USB Hi-Speed, is NEITHER VISA license are included?  488.2 NOR pilot is that CD is included along so I guess its license.

  In accordance with the licensing policy as long as you are using hardware NOR the license included.

  Here is the sentence that does this is clear.

  "Are examples of products that include the driver NI-VISA LabVIEW, CVI, TestStand, NOR-488. 2, GPIB controllers, PXI controllers, etc. If you do not use a software or hardware, you can buy NI-VISA development software separately. »

  If my understanding is 488.2 and NI-VISA OR license is included if you use the NI GPIB for Hi Speed USB controller.

  Thank you

  ANI

  It's true and you can deploy a runtime of NI-VISA smaller with your executable file.

• How can I disable the mouse pad when you use a mouse plug-and-play?

  How can I disable the mouse pad when you use a mouse plug-and-play? I tried to disable the driver, and nothing works.

  Hello

  Check with support of the manufacturer system, documentation online or forums that there is probably
  Shortcut keys that enable and disable the touchpad functions.

  Parameters for TouchPad located in the control panel - mouse (there may be several tabs with TouchPad entered)
  and some come with a utility that loads in the Notification area next to the clock in the bottom right.

  ==========================================

  If necessary: (make sure that you have restarted at least once, if the above did not work)

  Panel of configuration manager devices - mouse and pointing devices - Double click on the touchpad - the driver tab-
  Click on update driver (it comes may not do anything like MS is far behind the drivers of certification), now right CLICK
  on the TouchPad and UNINSTALL.

  Then go to the USB and UNINSTALL ALL controllers except the category itself (all in). RESET

  This will refresh the driver for the TouchPad and battery USB. This does not prevent the touchpad from working.

  The similar procedure on XP, Windows 7 and Vista is the same, except that we need to clear the specific device if present.
  http://support.Microsoft.com/kb/310575

  Then go to the system manufacturer's website and get the latest touchpad drivers.

  Download - SAVE - go to where you put it-click on - RUN AS ADMIN.

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Windows Vista device not recognized USB

  I tried all the suggestions to solve this problem. What else is there to do. Right now I'm running the systm scan through the command line. The last thing that I had plugged into my computer for the USB error messsage to appear was my iPod. I've never had other USB problems besides this one. I have an A135-S2326 Toshila provided with Windows Vista Home Basic already installed. I have the latest update and BIOS version. I have reset the BIOS to the default setting and changed the time. I unplugged the computer from its "source and the battery. I've disabled all the USB ports restarted the computer, their permitted again. I uninstalled all the USB ports and let Windows reinstall them. I did everything I know to do, and still nothing. I have read and looked for a solution over and over again. Can someone help me please. I am in desperate need of a solution like yesterday. Thank you!!!

  Try a system restore to select a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  http://www.Apple.com/support/iPod/

  And also ask Apple iPod support in their product

  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp

  And download the latest USB Universal Serial Bus Controllers for your model laptop from toshiba.

  See you soon. Mick Murphy - Microsoft partner