Similar Questions

• USB drives not appearing is not in my computer, even if they can access

  This problem happened for years and there were so far no possible way to fix it.

  When I have a USB device is plugged, the folder on the drive does not appear in the post. Yet it appears in the Device Manager or in devices and printers. If I type in the drive letter (H: /) in Windows Explorer, it works.

  Also, in devices and printers, the "Browse files" option is grayed out and I can not access network drives - I can't get C to G (E being my DVD player and G being my external hard drive). It only works if I type in the drive letter.

  Is it possible I have USB drives appear in my work so that I don't have to type the letter to? I tried USBs on my other computer and it works fine.

  Hello Tsukasa,

  Please keep us updated on the status of the issue.

  I'm glad that you managed to solve the problem.

  I appreciate your effort, time and patience.

  You can mark your answer as a response.

  Please do not hesitate to answer, if you have other problems with Windows.

  Thank you

• Cannot share the SD as usb drive

  I'm under 1.1 on a fire of Alcatel filed. I enabled two options to share the sd card (which works fine) as a usb drive, but it does not recognize my computer (Debian). When I connect the phone, it creates an sdb entry in / dev, but without partition (sdb1).

  So far, the only way to achieve this is by issuing the command described here (http://yorik.uncreated.net/guestblog.php?2014=15), "Adding access usb to SD card" > step 5. I do whenever I plug in the phone, of course.

  Additional information:
  -The sd card works fine. I can use it on the computer with a microsd card.
  -The sd card works fine on the phone too.
  -J' have enabled usb drive and shared the sd card in the phone.
  -The page I linked indicates the partition should appear when I unlock the home screen, I have tried that but it still does not work.

  This has been resolved for me in rev version 1.1.0.0 01020.

• Apple iPhone 4S for windows 8.1 usb driver

  Apple iPhone 4S no usb driver for windows 8.1

  Hello syap_pop,

  It seems that you have the driver installed on Windows 8.1 for iOS devices. Use this section of the following article:

  If iTunes does not recognize your iPhone, iPad, or iPod

  You do not see the Apple Mobile Device USB Driver

  1. Disconnect your device from your computer.
  2. Save a screenshot by pressing the Home button and sleep/wake button of the device button at the same time. The screen should Flash briefly.
  3. Reconnect your device to your computer.
  4. If you see one of these sections in the Device Manager, expand them:
     • Imaging devices
     • Other devices
     • Portable devices
     • USB Bus controllers

  Now, locate the entry that recognizes the device as a camera. You should see 'Apple IPhone', 'Apple iPad' or 'Apple iPod '. Right-click the device entry, and then manually update the Apple Mobile Device USB driver.

  If a single unknown device appears, follow these steps:

  1. Right click on the unknown device entry.
  2. Choose Properties from the context menu, and then click the Details tab.
  3. In the drop-down menu, select hardware IDS.
  4. If the ID begins with something other than USB\VID_0000 & PID_0000, go into the Device Manager and right click on the entry for device unknown, and then manually update the Apple Mobile Device USB driver.
  5. If the ID begins with USB\VID_0000 & PID_0000, then follow the remaining steps.
  6. Unplug the unit and remove all the USB devices on the computer.
  7. Shut down the computer, and then turn it back on.
  8. Reconnect the device, tests of each USB port for about 30 seconds to see if the device is recognized.
  9. Test with a different, checked 30-pins-USB or the lightning-connector-cable-USB, if they are available.

  If you still need help, contact Apple technical support.

  Thank you for using communities of Apple Support.

• How to see files on a connected USB drive

  I bought a

  GooDGo (TM) 30 pins for cable Charge USB Host OTG synchronization for iPad adapter 1/2/3 white

  which is a connector to a female USB 30 pin, supposedly it allows you to connect the USB storage device to the iPad. That do I do on iOS to see everything that is on the USB card I attach, and what formatting should have the USB adapter to work? I would copy the video content from my Mac to a USB drive and see the videos on my iPad.

  You need to trick your iPad by seeing these files as if they were on a camera

  Give your video files to a name of 8 characters. This mimicks a camera; s naming protocol. MOV_1244.MP4 example

  Place these files in a folder named DCIM

  Plug your USB into the USB connector (which may or may not work as number of USB drives also requires a lot of power of the iPad so trigger a warning ' device requires too much power "and the USB will not connect)

  Open the photos app (it may or may not open automatically)

  The last time I tried this I could not see the names of files, just the files were there. I had to import them into my iPad via the import of the photo app tab.

  Then try to look through the photos app, which should trigger the video application to open and you can see your video.

  This work is also based on the videos being coded in a way that the iPad is going to play, you have enough space to import their and it still works as it did the last time I tried it a few years ago.

• lgvm670 android USB driver do not settle

  the driver for lgvm670 USB android does not settle and cannot be found by the computer, I also try the LG site and they do not have the driver, I spoke on the phone with LG tech.support, and they were unable to help him. Any ideas?, I'll appreciate. Tanks

  HI cxt5510,

  The windows Compatibility Web site saying your phone is compatible, but it is free to download required. Check out the link provided below, scroll and click on the "update software" tab to download the usb driver for windows.

  http://www.LG.com/us/support-mobile/LG-VM670

  Let us know if this helped.

• ACER S7-391 RECOVERY OF A BACKUP ON USB DRIVE - BOOTING FROM A USB DRIVE.

  The manual shows as below: -.

  If it is not already enabled, you must enable the

  F12 Boot Menu and once switched on and registered:-

  During startup, press Fn> + => to open the start menu. The boot menu allows you to choose which device, select the USB drive. Use the arrow keys to select the USB device, then press on Enter.

  I activated with F12 success and after pressing F12(Fn+=) only the windows startup menu appears with no possibility of selection.

  I should if Acer community member can help with instructions step by step on how to get a boot menu by selecting the USB stick to boot from.

  Thanks for help

  Boot Mode UEFI is where you were mistaken. You will need to attach it to Legacy to boot from USB drive and restore your backup, UEFI will happen to return to Windows (according to Acer).

  Your USB flash is bootable, however it does not contain your actual backup (disk image) files. If you did your USB bootable after backup, well, your backup went, as in the process of making a USB flash drive bootable, that the drive is wiped.

  I would suggest to update your Bios, the direct download of the here are more late (2.15).

• How to make a portable USB drive use the same drive letter all the time

  Original title:

  I have many removable hard drives from Toshiba.  Use them for photography.  I usually connect simply, transfer photos from the DSLR camera (images raw, very big, not a camera point/rod).  When I plug in, computer automatically selects a player... F, g, H: by M or N.

  Then, I use Adobe Lightroom for adjustments.  Once they are imported into Lightroom it keeps track of this record, they were on.

  PROBLEM:

  If I unplug the removable hard drive, plug in at a later date, computer can randomly choose a different example M instead of H letter.
  LightRoom is so impossible to find photos/images.  I would then have to re - import and start any setting completely from the beginning.

  Question:
  How to direct the computer to select the same drive when I plug in a removable hard drive.

  Plug in a hard drive removable, computer selects H:, can I import into LightRoom, I disconnect the removable hard drive, a week later I want to make adjustments more photography, connect the removable hard drive and FORCE/DIRECT COMPUTER TO SELECT H: AGAIN (or whatever of the original letter was).

  Hope it makes sense.

  Jim

  Hello

  There is a way to assign a static drive on an external USB drive letter, so you always get the same drive letter for the drive.

  Click on the following link and follow the steps to change a drive letter.

  Change, add, or remove a drive letter

  http://Windows.Microsoft.com/en-us/Windows-Vista/change-add-or-remove-a-drive-letter

  I hope this helps.

• When the computer is turned off to stop is no longer the Vista 64 external USB Drive (SeaGate/Maxtor)

  Vista 64 - bit SP2. TB external Maxtor OneTouch 4 drive, worked well, now he wants to run continuously. The USB disk drive does not stop when I go through the steps to Remove material for it, then shut down the computer normally. Or the last step of the computer stops the disk external closing. Now the external hard drive keeps spinning, I don't know about the heads of read/write being parked or not and the white light comes on. This disk is used for the storage of photos; 30 backups; and several databases. I can't wait to have the drive platters turning 24 x 7, and I can't confirm that the read/write heads were parked safely. The error message associated with this question is below in bold. The player is now like the rabbit, continuous running.

  Diagnosis of Maxtor for this drive have been executed successfully.

  Maxtor check driver indicates that the driver is the most recent.

  Device driver Vista says the car is fine. I checked that the drive can read and write. Different backups have been recorded on this disc. I have not tried a restore because of this problem.

  Maxtor says that there is not any change in firmware pending for this drive.

  Seem like a command to close jammed somehow being sent on disk.

  Apparently the Maxtor One Touch USB Device, property, to optimize for quick removal of the external drive, you just completely shut down the computer and the external hard drive finished last (no need to use the hardware logic safely remove). The other option here is "optimized for performance (you must use the material logic safely remove) to turn off the player."

  These flags are defined in the Device Manager-online records-online Mass storage Drive L:

  Anyway, you try to stop the external hard drive, it will fail with the following error message:

  "Windows can't stop your 'Generic Volume' device because he's busy." Try again later. " Or a statement to this effect."

  The only software running when the error is Vista 64 bit and the logic of trying to stop the player.

  Thanks for any help you might be able to offer. Bill Sullens

  Hi Bill,

  Thanks for the detailed explanation

  I you suggest to activate the clean boot and then test to see if this works very well as expected

  Step 1: Put the computer in a clean boot

  Follow step 1 in the link below,

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  If everything works well after a clean boot, you can deduce that some third-party services are at the origin of the problem.

  Continue with the remaining steps to pin-point on the third party service.

  After find you the program that is causing the problem, you will have to perhaps to update or install a newer version of the program, if you rarely use that you should consider uninstalling the software.

  Important: n ' forget not the computer to start normal follow step 7 in the link.

  Let us know if this helps

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• My sm bus controller and controller USB driver not there (read for detailed explanations)

  I have a laptop, it was windows 8.0 and I upgraded to 8.1, I didn't like it at all so I lowered it to win7 because it was laggy and the displayed text was fuzzy. I knew that something was wrong with the installation of windows 8 and even after a clean full format, he would not return to normal. I went and he downgraded because I had enough and know that windows 7 would be faster for this pc (which it was), I said yaay sound much smoother and faster with no problems.  Then I installed all the wifi, bluetooth drivers, mouse etc... only 2 things that I couldn't install was the bus controller SM and USB bus controller driver (USB). And my usb slots were not working other than port 3.0 I had a plugged usb of decommissioning...

  I know its something to do with the bios and since the update of the bios is 8 - 8.1 windows only I don't know what to do... I have a .wim file recovery and I don't know how to use it. I also forgot to put my product key of my pc of win8 before I went down I had no knowledge of what happen and don't think it would be a problem...  Now I can't connect more than 1 thing at a time. I went on the microsoft forums and they fixed a problem (ethernet driver) and told me to come here and I hope you can fix the rest.

  Thanks to adnvaced for your help

  The laptop is HP Pavilion Sleekbook 14-b006au
  Serial number: 5CD2490Y40
  Product number: C7D41PA

  Please can someone help me I really want to stay under windows 7 is it possible that someone could get an update of the bios manual for that laptop or something like that. Except that everything works fine!

  Here's a linnk to MS32 (computers)

  http://1drv.Ms/1u6Z6DP

  Hello:

  Here are links to the drivers you need.

  1 SMBus: Downloand unzip and manually install the driver for smbus controller I have attached under attachments below.

  Go to Device Manager and click the controller smbus needing drivers.  Click the driver tab.  Click on set to update driver.

  Select her browse my computer for driver software option and navigate to the driver folder that you unzipped.

  Make sure that the include subfolders is selected and the driver should install.  Then restart.

  2 USB3: Download and install both of these drivers and restart.

  http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=6943836&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_137148_1%257CswEnvOID%253D4058%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

  http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=6943836&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_133037_1%257CswEnvOID%253D4058%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

• Loading file to the Virtual Machine by using an external USB drive... Please help

  We have an environment that we would like to import and create a virtual machine. The files are on the external 1 TB external hard drive USB puppy with NTFS. The files are approximately 430 GB. I tried almost all the options to get the files to the HOST that is running the server ESXI 4.0.

  Whenever we tried to get the files using the USB drive and Vsphere client connected to a local computer running windows on the ESXI 4.0 Server somehow transfer stops after a while. Some time around after ro possibly around 250 GB 200 GB. So far, we are not able to get the hard master file that occupies about 430 GB in the ESXI data store.  We also tried the third "Fastscp" software to transfer files to the ESXI host, but we had the same problem that the transfer stops at some point.

  Another option that we tired was to start a machine with Linux live CD and USB directly attached to this machine. As the Linux version was newer USB NTFS partition hard drive has been detected without installing any NTFS disks. We have mounted the drive USB on this machine and exported the mount point. In the ESXI server using CLI not supported (Alt - F1) we were able to ride the point of editing exported and tried to copy the files to the folder main datastore but same problem the transfer stops after a few hours sometimes even near 300 GB.

  Y at - it somehow I can bypass the file transfer by using not not the network, which means that if we reach directly the USB key to the ESXI server machine does not recognize it (using Alt - F1 not CLI) because it is partitioned into NTFS. I read that ESXI only supports FAT partition.

  We also tried to start the machine running ESXI server with the latest versions of Linux, in this case, we were able to mount the USB drive directly, but because ESXI stores files with VMFS partition we couldn't mount this partition in linux.

  Could you please recommend any solution to get the files the server ESXI 4.0?  Is there a way to allow us to start the EXSI with Linux server and can mount the partition VMFS use third-party drivers? OR what you would do. Advice would be nice.

  Welcome to the forums - using the vSphere client should work - block of what size did you use to create your VMFS data store? If you left it at the default of 1 MB, then the bigger file, you can copy that VMFS datastore is 256 GB - you'll need to create the data store with a block size of 2 MB which will allow you to create a file upto 4 MB or 512 GB keast and a size of 1024 GB.

  If you find this or any other answer useful please consider awarding points marking the answer correct or useful

• How can I migrate a time machine backup external USB drive to time capsule

  Searched the forums and can't seem to find an answer. With the help of El Capitan 10.11.6. You want to transfer backups Time Machine 4 years on an external USB drive on my new Time Capsule. Any ideas would be MUCH appreciated.

  There is no official method because it has problems.

  There's no official way.

  Here see Q18. http://pondini.org/TM/FAQ.html

  We recommend that people not me there. It has not proven reliable long-term. Start a new backup on the TC and keep the USB stick in the form of archive. After a few months or a year you won't have it.

  You have to understand the Time Machine backup otherwise locally the CF network. It is easy enough to move the backup network local but much harder the other way around.

• How can I make an external USB drive read-only?

  I'm trying to find a solution to take a USB HD in a spacing classified environment / air.  If I can make the drive read-only (like I gave him that I need to copy on these machines), then the Agency will probably approve the device.  I can't use DVDs that data are 30 + GB in size.

  Hey there, capsfanva!

  Welcome to the communities of Apple Support! It seems you need to set permissions on an external USB drive or hard drive. These permissions setting is a great way to improve the security and privacy of these elements. You've come to the right place and you will find the answer below. You must connect the device to your computer and follow these steps:

  Set permissions for the items on your Mac OS X El Capitan:

  See you soon!

• Display a dialog box after the ejection of a USB drive, saying the car was ejected

  Hi, would someone please tell me how to change the applescript below to eject my USB in 2 ways, either by waiting 30 seconds by pressing the button "YES". Then, once the disc has been ejected another dialog box would appear to say 'eject disk '. If 'NO' button has been activated the reader wouldn't be ejected. My USB is indicated as (the present book).  Thanks in advance for any help.

                                                              tell application 'Finder '.

  display the dialog box "Eject USB drive?" default button 1 with the title "Eject?" buttons {'yes', 'No'} give up after 30

  If the button returned of the result is 'yes' then ejection of the this book

  tell the end

  Here:

  Tell application "Finder".

  Display dialog "Eject USB Drive?" buttons {"Yes", "No"} default button 1 with the title "Eject?" give up after 3

  If the result back button is 'yes' or abandoned then of the result

  This book of ejection

  display the dialog box 'Disc ejected.'

  end if

  tell the end

  (143586)

• Move backup by USB-drive to Time Capsule

  I used to make with Time Machine backups on an external USB drive. Now, I would like to move these old backups to my new Time Capsule.

  Is this possible? And how do I do it?

  Thank you

  Click here and follow the instructions.

  (143017)