USB key do not recognize my magcjack

Similar Questions

• USB keys do not work in my VISTA PC, but working in the XP computer.

  My PC is only a few months and underwarranty. VISTA is OEM original and authentic. All updates and installed SP2.

  But I have several problems with VISTA.

  One of them is the following:-

  USB keys do not work in this PC. Initially, they are recognized, but as soon as I start the data transfer it stops and does not recognize the keys more. Same USB keys work correctly on other XP computers.

  An external hard drive works perfectly on the same USB port. If the port is fine.

  Hello PG_eu,

  First of all if still under warranty, contact the manufacturer to execute tests for your USB slots. Have you tried to see if other devices work on the USB plug? The manufacturer of your may be able to replace your computer if needed.

  Then, I'd go for the Device Manager to see if you have errors. Go to Device Manager and see if you have a yellow fringe! showing that there are errors with your USB devices. Open the Device Manager in Windows Vista via the management utility of the computer, the Control Panel, or from the command prompt by typing in devmgmt.msc.

  You can go to the different tabs and see if the devices work properly, should be cancelled or update your drivers.
  You can also go into the event viewer and see if you have errors on your hardware devices.

  I hope this helps.

  Sincerely,

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Your bootable USB key could not be created

  "Your bootable USB key could not be created.

  Hey guys,.

  I Googled what to do about this error message and all I got was to ensure that the ISO is disassembled. I did, and yet I still get the same exact error message. I'm trying to get Windows 7 Home Premium on a 2012-13 inch Mac Book Pro. I also use a flashdrive 16 GB for the ISO image. Any ideas on how to solve this problem?

  Please read: create an ISO image for the Boot Camp Windows installation media.

• "Your bootable USB key could not be created there is not enough space available on the disk.

  I am trying to install a partition of Windows 7 with an ISO on a flash drive with Boot Camp Assistant. Everytime I try it however, I get the error "your bootable USB key could not be created there is not enough space available on the disk. The flash drive that I use for this is 64 GB, so I doubt that the issue has to do with not enough available space. I have already tried the obvious, like reformat the flash drive and retry the write. Is there something I could hurt or do differently to make it work?

  MacBook Pro (retina, mid-2012)

  2.6 GHz Intel Core i7

  8 GB 1600 MHz DDR3

  NVIDIA GeForce GT 650M 1024Mo

  Use a 8GB drive.

• Tecra A4 - USB keys do not appear in 'my computer '.

  I recently had to restore my TECRA A4 system after a disaster, since then, usb keys do not appear in 'my computer' and aren't available to use? However, they are listed in the device under usb devices Manager and hard drives?

  I updated the Bios and looked for the updated USB drivers, but nothing found?

  Hello

  Maybe stupid thing, but try it please follow: disconnect your laptop computer, adapter sector and battery and leave about 60 minutes. After only 60 minutes connect AC adapter / CC, start your laptop and try to use the USB.

  Please let me know what happens after that.

  By the way: check this http://support.microsoft.com/default.aspx?scid=kb;en-us;817900 document

• Satellite Pro L10 - USB port will not recognize devices

  Hello

  I got a L10 for 18 months. Under the guarantee, I got a replacement motherboard mounted. Everything has been ok so far. A USB port will not recognize devices, a port is ok, but randomly turns off a device attached to it and comes up with the message "USB device not recognized". The third port is ok all the time.

  Any solutions or suggestions?

  Post edited by: caddy

  I guess there is not enough power on the USB ports and external devices may not work correctly. It is not easy to say why this happens, but there may be a problem of welding.

  I recommend you contact the service again as soon as possible.

• Dell: inspiron 1525 not boot from a USB stick, USB key are not not in the start option.

  Hi all

  I bought this dell laptop inspiron 1525 in the year 2008 with mentioned configuration:

  Core 2 duo processor

  1 GB OF RAM

  Due to some problems in my windows vista, I decided to install a new windows vista in my laptop. I run the dell support live cd at the start of my laptop and created the partitions on my system. But while the new installation OS on the cd i found that optical drive of my system does not work very well. so, I decided to install the new OS of USB. I went to the BIOS and selected the USB key in the boot sequence. but when I tried to install the new OS while pressing the F12 key, USB key is not listed in the start option.

  could someone help me to install the new OS in my machine? It is very urgent that my machine is down for 1 week.

  Please try attached BIOS changes screenshot than everything be useful to me.

  Thank you

  Gurpreet

  Hi Gurpreet,

  Thank you for your response.

  My apologies if I seem repetitive, but when you go to the Option of boot sequence in the system configuration screen, do you think that the USB storage device listed? And do you see a number in front of it?

  Go to the option for embedded devices and check if the USB ports are enabled or disabled. If disabled, change the option and enable the USB Ports.

  If this step does not help, go to the Maintenance option in the system configuration screen and press enter on 'Load Defaults'. On the side right, highlight 'Continue' in green, press Enter and then save & exit.

  Please keep us informed of the results.

  Thank you and best regards,
  Babita S
  #iworkforDell

  For easy access to the drivers, manuals and updates, please visit our Support Site .

• Ports USB PC do not recognize

  I was download any last night on my USB falsh, then for some reason when I go on ' send to ' it does not recognize one of my USB ports.  It doesn't give me that option.  That's happened?  pls help thanks

  Hello again. I have a few steps I would take so that we make an attempt to get this problem solved for you. If go to your start screen, and then just type Device Manager. This will open a list of all installed devices or integrated to your computer as you. Scroll down the list until you see Bus USB controllers, and then click the arrow to the left to expand the list. If you see a ""! "mark next to one of the USB ports, then you must click with the right button on them and then you update the driver options, activate the port, uninstall or Scan for hardware changes." Please let me know if it helps. Also, just for fun, I would try another USB key just in case you used that has become corrupted.

  Thanks again.

• Staples relay USB key does not?

  Recently, I bought a relay 8 GB USB Flash drive, and it works great under XP. But in Vista, it will run for 2 seconds and then stops. I tried everything I can think of. (Tho can't really remind them now. =) Staples support has not been able to help me, (big surprise), so I guess it has something to do with Vista. I just installed SP2 as well and it still doesn't work. When I bought it, I have the formatted in FAT32, with the Vista laptop.

  It does not give any error message, it just stopped responding. Almost as if I would take it outside, but it's not. Whenever I try to open it, it closes. With whatever it is.

  Help, please. :( I have things that I need it.

  Hi Tosai,

  Welcome to Microsoft Vista answers Forum!

  Vista does not recognize devices that are the reason for the USB key to the FAT 32 format, that is perhaps not getting recognized, you may need to convert the machine to NTFS, follow these steps to convert the machine to NTFS:

  Click Start > type in the Device Manager in the research starting > expand disk drives to find the USB device > click with the right button on the player > select Properties > then go to the policies tab > select the "Optimize for performance" option and click OK, and then do the format, then select NTFS.

  Additional information: convert a hard disk or partition to NTFS format:  http://windowshelp.microsoft.com/Windows/en-US/Help/414a3808-283a-4e4d-b5ff-1a6d06f597d31033.mspx

  Hope this information is useful.
  Let me know if it worked.
  All the best!

  Thank you, and in what concerns:
  Swathi B - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Usb keys do not work on HP CM1415FNW

  I have a printer HP CM1415FNW. I need to scan and transfer of files on my usb key. In fact, the printer may read less than 8GB, over her keys cannot read.

  Is there a solution?

  According to this Manual on the walk up to the USB function, the printer does not support USB flash drives, over 2 GB, so it's likely that the 8 GB working.  You could try to do an update of the firmware and see if that gets a job 16 GB, but more probably it won't help.  If you need help with the update of the firmware, I would like to know what operating system using the your and I'll connect you to the latest version.

• USB key does not

  My USB key "command in use by another program" when I go to delete, format, or add things when well even's them not all programs upward, which is to use it.

  Help?

  Hello

  A clear way to determine if a service or something hangs the process is to start your system with a cleanboot, then repeat the process.

  Here is an article for cleanboot.  Follow the steps until you have isolated service.

  http://support.Microsoft.com/kb/331796

  -Debbie, Support Engineer-

• Cannot access BIOS when OS disk encrypted w / Bitlocker, starting on the USB key is not unlock disc

  Hello

  I enabled Bitlocker on my Acer Aspire 5315. The system partition is encrypted and the data partition. My motherboard doesn't have a TPM chip, so I opted for the unlock with a USB key.

  When I start the PC or wake them from their hibernation, the splashboot (with the logo of Acer) BIOS screen does not display the information below on how to access the BIOS (press F2) or the boot menu (F12). And therefore I can't access those as I used to.

  BitLocker does not account for the USB key, then asks for the password to unlock the HARD drive. Then Windows starts very well.

  However, restart (by a Windows or after you have entered the wrong password Bitlocker too many times), the BIOS splash screen is normal (with how access BIOS and boot menu), I can access BIOS by pressing F2 AND succesfully Bitlocker unlocks the HARD drive with the USB flash drive without having to ask for the password.

  So, my question is how Bitlocker unlock the HARD disk automatically via the USB when the PC starts?

  Thank you for reading.

  Note: I posted this question on http://social.technet.microsoft.com/Forums/en-US/w8itprosecurity/threads they suggested that I ask the Acer support.

  Thank you also get answers in the TechNet forums.  I'm sorry that you were unable to get a more complete answer it.

  We suggest that you uninstall BitLocker and decrypt the drive to determine if this restores your ability to access the BIOS.

• USB and DVD not recognize anything it shows that peripheral unknown.

  Original title: USD/DVD does not work.

  my USB and DVD does not recognize anything, it shows device unknown and does not work.

  Hi alexandrebernat,

  You did it all change hardware or software on your computer before this problem?

  For the question USB, you can follow this link & check if it helps.

  USB port may stop working after you remove or insert a USB device

  Reference: Troubleshooting tips advanced to General problems USB in Windows XP

  For the CD/DVD drive problem, you can follow this & check if it helps.

  Your CD or DVD drive cannot read or write media

  Reference: How to troubleshoot common problems that occur when a Windows XP-based computer cannot read a CD or DVD

  Hope the helps of information.
  Please post back and we do know.

• Watch USB key and not the Sansa player

  When I plugged in my sansa e260 v1 to the computer for the first time, I think what he recognized as a sansa e260.  Well, I wanted to get rid of the files of stock on the player that I did the format process (Virgin sansa.fmt file).  Well I did, and now it seems that whenever I plug the sansa to the computer, the computer just shown as a USB key.  I can click on the drive and it shows all folders on the sansa and I can drag and drop files into the music folder and they seem to play ok, but I was wondering if anyone has experienced my problem.  When I moved on several MP3s (about 10), the player says 'written' for hours.  Now, I also placed on 1 song and disconnected the sansa when the computer showed that it has been copied but the sansa continued to show "writing".  Another question I have is can I installed rockbox.  When I try it says "disk access denied permission.  All of the above questions, I have the sansa player has been in MSC mode.  I had the most up-to-date firmwaree also when these issues were ongoing.  I have downgraded the firmware but didn't try something else without some advice.  I m running Windows vista.  I really like this player and hope, that I can get rid of these questions, and then I'll be totally satisfied.   Thank you for your time in advance.   I hope that I gave all the information that would be required.  If this isn't the case, I'll try to provide some other info someone may need.

  I called Sansa.  They accompanied me through the formatting through windows.  They could not tell me something, all being stuck in the writing mode if other say formatting it may fix this problem.  I wish they could just come out and say tehre is a bug and they do not have a fix for this.

• My USB ports do not recognize my external devices

  Hello

  My USB ports are a complete mess. My external drive and my USB is not recognized in one of the ports, my mouse is recognized only in 2 of them, my cam and my mobile are recognized throughout. The external drive, USB key, and mouse already worked in all ports, but stopped working after I sent the PC to the store; Apparently, they did do a very good job.

  Could you help me please? The main problem is that I have everything in my external drive and cannot transmit information of my laptop anywhere.

  Thank you...

  Hi ZukaRashid,

  Thanks for the replies.

  Now let's see if from the information that you have provided the best way to help.

  Since you are on XP, this question would have been better served at the XP forum, but we will work with you from here to find solutions.

  Here are some articles to the Knowledge Base that may apply to your situation:

  • Please do not forget to back up all critical data and create a system restore point before you follow the steps below.

  Troubleshooting articles:

  One or more USB devices may not work when you start your Windows XP-based computer

  USB port may stop working after you remove or insert a USB device

  Peripheral input USB do not work in Mode safe mode or Real Mode

  For your information items:

  Basics on development of device drivers universal serial bus (USB)

  Please follow the troubleshooting steps that are listed in the articles and keep us informed on this issue.

  I'd preferably starting with PORT USB CAN STOP of WORK AFTER YOU REMOVE or INSERT A USB DEVICE.

  Thanks again for the announcement in our discussion group.

  Debbie
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.