USB PORTS NOT EXTERNAL SENSORS

Similar Questions

• Satellite P10-304: USB Ports not recognize anything

  I have a Satellite P10-304 and the USB ports not recognize anything that are attached to them. Device Manager tells me that they are enbaled and works correctly. What can be wrong with them or what can I do?

  Hello

  One of my friends has the same unit on the work and everything works perfectly. It uses the USB hub too and have many external devices connected to the unit.

  By the way: something like who can occur if the external device is not removed correctly use safely remove hardware option. If you try to connect any other device after that in most cases it is not recognized at all. In this case, you can restart the device or remove ports from the Device Manager and use the hardware detection to find them again.

  Good bye

• USB ports not working do not. Pavilion dm4-3090se

  USB ports not working do not.

  Thanks for your reply.

  no ports were working, so I went into Device Manager, uninstalled them, re-started... and... iola!

  they were back!

  Thank you again for your answer...

  Louise

• USB port not to pick up when it is connected

  USB PORT NOT TO PICK UP WHEN IT IS CONNECTED

  Himanshu salvation,

  ·         How long have you been faced with this problem?

  ·         Did you make any changes before the show?

  Refer to the following Microsoft Fix It solution and click run now , and follow the steps to solve the problem:

  Hardware devices do not work or are not detected in Windows:

  http://support.Microsoft.com/mats/hardware_device_problems/

  Hope this information helps.

• Spectrum of HP 13-v013tu: USB port not working not not the spectrum 13

  Hello.  I bought the HP 13-v013tu a few months ago spectrum and in general the laptop works very well.  However, I noticed that 3 C type USB ports in the back, one of them do not work.  The USB port for the electrical connection to the right is fine, but the two in the Middle, one of them work.  Who does not work does not recognize or even to send power what it is connected (for example, the mobile phone, the external hard drive, load wireless mouse).

  I checked the Device Manager and see nothing wrong in the USB options.  Even the option of power management to allow the computer to turn off the device has been disabled.

  Can anyone help? Is this a hardware problem?

  Thank you.

  USB - C for USB 3 adapter supplied with the laptop you are using? If it works in 2 of the three ports, then the logical conclusion is that the third part is bad. You can actually power the laptop of one of the Thunderbolt-C/USB ports (I have one of these laptops) in order to try in the port which is giving you issues and if he does not have the power, then you have a dead port which will require the replacement of the motherboard.

• Satellite C50 - B - 14 d - USB ports not working not

  I have a C50 Satellite - B - 14 d and had again for about 4 months.

  I didn't know that at the time of the purchase (online) that there is no optical drive, so I bought an external.

  Trying to plug into it, discovered that nothing happened in the 2 ports on the right side (2.0 and 3.0) so I decided to try the left port 2.0.

  It does not detect the device, but it undetects then within 10 seconds, it continues to do this every few seconds it is impossible for me to access my work on CD!

  I contacted the people I bought it since then, but they say it's a matter of Toshiba?
  Can someone help to solve what I don't want to send it for repair because I can't be without him more than 2 days.

  HHHEEEEELLLLPPPPPPP!

  I put t he thinks that the s notebook issue if all the USB ports work in relation to other devices USB; That is to say the USB mouse.

  From my point of view of a few external USB CD/DVD drive could not be recognized because of the low power of the USB.

  Try to connect the CD/DVD drive to the laptop using the USB Y cable which allows to connect to two USB ports.

• Z500 8.1 Windows 64-bit USB ports not working not

  Hi everyone, now I have bought a lenovo Z500. After update to 8.1 Windows 64 bit, USB flashdrives could not run properly eventually Explorer Windows did not. When I try to restart, it blocks on the screen "Restart" and I have to press and hold the power button to power unit off which is very dangerous for the laptop. Other usb devices work well as a drive external hard, mouse and keyboard. USB flash drive only have such a problem. When I insert my USB key, I hear the sound which indicates that a device has been inserted. It is not the usb flash drive, because I tried with different USB keys and the same thing happens. All USB keys works well on my desktop (Windows 7).

  Thank you..!!

  After you uninstall a software firewall, USB port, back to normal.

  Thank you.

• 8.1 Windows 64 - bit 3 USB ports not working not

  I have a model computer T430s 2352CTO, running Windows 8.1, 64-bit version. Before upgrading Windows 8.0 all drivers have been updated. The USB ports 3 worked properly, in particular an external hard drive of 1 GB running. After the 8.1 update, 3 USB ports work always, but only for about 30 seconds, then the hard drive stops. The power led remains on the hard drive, but it no longer displays in windows Explorer.

  In Device Manager, I'm gone to Bus USB-> USB controllers Root Hub-> properties-> (under general it says "this device does not work correctly)-> Power Management-> unchecked the box"allow the computer to turn off this device to save energy. Unfortunately, it doesn't seem to stop the problem. Any ideas?

  Please try this:

  http://blogs.msdn.com/b/usbcoreblog/archive/2013/11/01/help-after-installing-Windows-8-1-my-USB-DRIV...

  Thank you!

  Houman

• V5 - 573 leaves g USB port not recognize devices

  Hy. my USB port left I does not. It's loaded, but not to recognize the devices. tried it with the mouse, usb, external hard drive, flash drive all numb. but the power is there. I see the light on the external hard drive if pluged in. any suggestions? TNX

  Well, guess you should contact technical support now. Sorry mate.

• USB port not recognize mice and other devices.

  I have a logitech wireless mouse who worked on my computer (Fujitsu A6220) for 2.5 years, but now device for ports management USB says that it does not recognize the device.  I travel and a few times I returned from a trip and trendy and it worked for a few days.  I have the same problem with my printer and an external drive connected to the USB ports.  I also tried a USB mouse that is not wireless and same problem.  The mouse works on other computers.  I tried the update of drivers and get a response the the best driver is already installed.

  So, this could be a hardware problem?

  I get the error message is: Windows stopped device (Code 43) port #0001, Hub_ #000

  Hello

  1 did you change on your computer?

  You can connect another USB device into the outlet to check if it works.

  Method 1:

  Step 1:

  Remove and reinstall all USB controllers to remove and reinstall all USB controllers, follow these steps:

  (a) click Start, run, type sysdm.cpl in the Open box, and then click OK.

  (b) click on the Hardware tab.

  (c) click the Device Manager button.

  (d) expand Bus USB controllers.

  (e) right click on each device under the Bus USB controllers node and then click on uninstall to remove them one at a time.

  (f) restart the computer and reinstall the USB controllers.

  (g) connect the removable USB storage device and perform a test to ensure that the problem is solved

  Step 2:

  You can visit this link below and check if the problem gets solved by running the fixit.

  http://support.Microsoft.com/GP/hardware_device_problems

  Tips for solving problems of USB devices

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices

  Method 2:

  I suggest you to follow the steps from the link and check.

  Code 43: Windows has stopped this device because it has reported problems

  http://TechNet.Microsoft.com/en-us/library/cc725873 (WS.10) .aspx

• One of my USB ports not working

  I have an Asus Zenbook Ux31e. It has a USB port on the left and right. The one on the left has stopped working a few months ago. It does nothing when I plug in my external hard drive, my mouse or my flash drive. Oddly enough, it DOES not work when I plug in my disk drive. The right side works perfectly so I wonder what I can do to solve this problem.

  Here is a picture of Device Manager.

  

  Hi Ams2ay,

  This problem is usually caused due to driver issues or because of material related issues. I would like to know some information about this problem so that we can help you further.

  1. have you made changes on the computer before this problem?

  2. do you get any error code or error message when connecting devices to the USB port?

  3 have you tried the troubleshooting steps to resolve this problem?

  I suggest you try to update the chipset drivers on the Asus or Windows Update site and check if it helps.

  http://Windows.Microsoft.com/en-in/Windows/Update-driver-hardware-ISN

  If the problem persists, then it would be better to contact Asus for further assistance in this matter, because this could be a problem with the hardware.

  Suport of Asus: http://support.asus.com/ServiceHome.aspx?SLanguage=en

  Please reply with the status of the issue so that we can better help you.

• USB ports not working no-Windows 7 on Imac

  Hello

  I ve just installed Windows 7 on an Imac end 2012, using an external hard drive and running in Bootcamp.
  Everything went well, Win 7 works perfectly, but all USB ports do not work. Everything I plug into their t doesn't get recognized (flash memory usb cards, mouse usb, external drives...).   They work in OSX.
  All other ports (ethernet, audio, output Thunderbolt) work very well under Win 7.
  What I tried, no still no usb operation:
  -Reinstall Win 7 (just to check that I used a mouse usb, what worked very well right up until the last reboot needed to complete the installation.) Subsequently died)
  -reinstall all software Bootcamp (actually, fix, that you can't just unninstall and reinstall) has done that several times...
  -tried to uninstall the usb ports in Device Manager, I couldn't use my Apple wireless mouse more, so I had to restart after the first. Yes, after a restart, he says it's to install the missing disks, yes they are all perfectly... However - install no USB
  -No, no problems appear in the resolution of the problems of the unit
  Do you have any other ideas I could try?
  Thank you very much.
  Marian Nedelcu
  Here is my config Imac. in case it helps:
  IMac 27 inch Quad-core

  3.4 GHz I7,

  32 GB OF RAM,

  3 to FusionDrive,

  NVIDIA GTX 680MX 2 GB,

  Magic Mouse, Apple wireless keyboard

  Hello

  I suggest you to contact the Apple support and check if it helps.

  http://www.Apple.com/support/Mac/

  Hope this information is useful.

• Zbook G3 HP: HP Zbook Thunderbolt 3 Dock USB ports not working not

  I have a HP Zbook Thunderbolt 3 dock on my HPZbook G3.  I've recently updated the BIOS and the firmware to the latest version to solve other problems 'dock '.  Am now at the latest for both.  The two monitors and ethernet on the work of lightning 3, but none of the USB ports are active.

  I am sure that the USB ports work, because they used to work before the update BIOS and firmware.  Keyboard, mouse, or USB memory on the dock work.

  I tried to go to the HP support and install the updates with the USB in it, but it didn't work.  I have a workaround - just connect the laptop directly, but I'd like to get my fully functioning dock.

  Device Manager does not display devices with questions.  I'll try to update, but I don't know which one to look at.

  

  Hey people,

  HP is dedicated to providing quality products to meet the needs of our customers. We listen to the customer feedback on our recent Thunderbolt Dock for use with the latest products ZBooks, and Elite Notebook. We continue to work with our customers to solve problems.

  Please find tips and updates to improve your use of the HP Thunderbolt docking station.

  1. The Thunderbolt dock uses the latest technology thunderbolt. To be fully functional, it takes the latest firmware, BIOS, and drivers to work properly. Please follow the step by step process as described below in "The process of updating your device".
  2. Here are links to the user, technical white paper guide helps and guides troubleshooting. Please, use them to help when you have problems after you have fully updated your device and platform by following the instructions above. Please note that you may copy and paste the links in your browser.
  3. If you still have any questions, please call HP support. We're here and eager to help succeed you using the HP docking station new Thunderbolt.

  Useful links

  User Guide: http://h20565.www2.hp.com/hpsc/doc/public/display?sp4ts.oid=11122586 & docLocale = en_US & docId = emr_na-c05141189

  Technical white paper: http://www8.hp.com/h20195/v2/GetPDF.aspx/4AA6-5088EEW.pdf

  Help & troubleshooting the Dock: www.hp.com \support\thunderbolt3dock

  Process to update your device

  NOTE: Instructions below is found in the User Guide "Getting Started" to "Implementation of the dock" to "step 2: update your computer.

  Before connecting the dock to your computer, update the BIOS, software and drivers on your computer.

  NOTE: If you do not, the wharf may not work. For best performance, keep all software and drivers on your computer up to date. (See table 1)

  Update the BIOS and the software and drivers:

  1. Go to http://www.hp.com/support. Select the drivers and Get software, enter your model of computer (on the computer service tag) number, and then select search for my product.
  2. Click the link for your specific computer, select your operating system and then download the latest version

  BIOS, software and drivers as follows: Intel® Thunderbolt Firmware Update Utility, Intel's Thunderbolt

  Secure Connect Driver, graphics drivers, ASMedia eXtensible Host Controller Driver, Broadcom Ethernet

  Controller and driver Conexant USB driver.

  1. Install the latest version of the BIOS.
  2. Restart the computer.
  3. Install the last stroke of lightning Secure Connect driver Intel.
  4. Restart the computer.
  5. Install the latest Intel Thunderbolt Firmware Update Utility
  6. Restart the computer.
  7. Install any remaining updates in any order. Restart the computer after each update.

  Table 1

  For the products supported Thunderbolt Dock all HP
  Name of the component	Category on the Support Page on hp.com	Where to check (this applies to all laptops)
  BIOS	(BIOS)	BIOS F10 Setup to information system
  Intel's Thunderbolt course connect driver	(Pilot - controller)	Right click on tray icon Thunderbolt to settings for details.

  The Thunderbolt of Intel® firmware update utility

  (Firmware)

  Right click on tray icon Thunderbolt to settings for details. Note that the numbers on the left will not directly reflected. NVM Firmware Version: 16 PD Firmware Version: 1.07.03

  Intel Graphics Driver

  (Driver - graphics)

  Right click on the desktop to graphic properties (icon intel) Options & Information Center Support.

  NVIDIA graphics driver

  (- Graphics - Nvidia driver)

  Right-click on the desktop to NVIDIA control panel to information system at the bottom left.

  AMD graphics driver

  (Driver - graphics)

  Right-click on the desktop to graphic properties (top) to Information to software.

  ASMedia eXtensible Host Controller Driver

  (Driver - Chipset)

  Programs & features or the Device Manager to Universal Serial Bus Controllers (dock of needs to be connected).

  Of Broadcom Ethernet controller driver

  (Driver - network)

  The Device Manager to network adapters (dock of needs to be connected).

  Conexant Audio Driver USB

  (Audio - driver)

  The Manager of devices to sound, video and game controllers (dock of needs to be connected).

  BPPSQ-

  I work on behalf of HP

• Satellite Pro L10-103 - USB ports not working not

  Hi, my Satellite Pro L10 - 103 USB Ports do not work. I tried different things and finally my Advisor rubbed my computer clean of all programs and operating system. After reloading of the set up disc and having lost my dear some programs I am no further forward. It still does not.

  Anyone know if this means that it is a mechanical problem with the computer? (I use Windows XP). Your help would be greatly appreciated.

  Hey Buddy,

  As wrote Akuma did you use the Toshiba Recovery disk or the Microsoft Windows disk?

  After installing XP, make sure that Service Pack 3 is installed. It contains important updates and can be downloaded on the official page of Toshiba.

  In addition, try to remove all the USB ports on the Device Manager, restart the computer. Ports will still be recognized and ready to use once.

• USB ports not working not not on Satellite Pro C650 - 18 d

  Hello
  I have a Satellite Pro C650 - 18 d on which USB ports are dead.
  So far, I've updated the chipset and BIOS - but they stay dead. It doesn't seem to be a power either. I have a USB key with LED and it does not light.

  Any ideas? It's under warranty and so unable to try something wild!

  Thanks for any help
  Jim

  Hi Jim

  I recommend you to reinstall the OS and test the feature with the factory settings. Please, test it with several different USB devices. If none of them works, you must contact the Toshiba service provider in your country and leave check s portable.

  Do you know how to find the addresses and phone numbers?