USB transfer device

Similar Questions

• Windows 7 is no longer reads the USB storage devices

  I have a problem similar to some other posts, but different enough so that I write it here.

  When I insert a USB storage device (like a Microcenter * Go Flash) Windows 7 Ultimate just shows a yellow exclamation mark next to the device in Device Manager. OtherDevices, USB Flash drive. Software update driver fails, no update.  Uninstalling and reinstalling has no effect.

  Under properties:

  Type of device: USB FLash Drive

  Maufacturer: unknown

  Location: Port_ #0003.Hub_ #0008

  Pilot wrote:

  Privder: unknown

  DAT: Not available

  Version: Not available

  digital GIS: dig signed ot

  Under Details:

  Hardware ID: USB\VID_1307 & PID_0163 & REV_0100

  USB\VID_1307 & PID_0163

  There is no ping, no popup. Nothing. All this used to work very well, and now, when I need to copy files to work urgrnetly, he's dead.

  Just rub a little salt, I CAN access the device through Linux in VMWare Workstation. But when vmware is not current execution, or when I disconnect and try to attach to host, nothing happens.

  I tried each storage device USB I can find and no luck on any of them.

  Thank you

  TMB

  After digging through the forums, I tried to copy the usbstor.inf and .pnf to the Windows\inf directory and reinstalled the driver through the Device Manager, and it loaded right up.

  I don't know, but I suspect that the impact of this change, there are other devices that can complain. For now, the process of transfer between W7 and VMWARE/linux seems flawless.

  TMB - back

• USB transfer

  I'm under ESXi 5.0 on a HP BL460c G1.

  Guest operating system is Windows Server 2003 Standard Edition SP1.

  vSphere Client runs on Server 2003 Standard SP2.

  I'm trying to virtualize a former server that is essential to the daily operations because the material on what there currently is 6 years old and management does not want to spend the money to have it replaced.

  One of the requirements of the software is a security device that is currently parallel, but we can get a USB version.

  Now the problem is I can not all USB devices to connect to the virtual machine that I created.

  • I tried to do a USB transfer under the host's configuration > advanced settings. but he said to me 'Host does not support configuring passthrough ".
  • I tried to connect a vSphere Client computer USB device; He tells me that the device is about to be disconnected from the host and connected to the virtual machine. Then after clicking 'ok' I get the message "the remote device on < virtual machine > to < device > is disconnected."

  It actually shows the name of the virtual machine instead of < virtual machine > and < device > is 'v2.0.33.

  Is there a way to fix this disconnect usb?

  > Configuring the host > advanced settings

  It's active VMdirectpath.  You don't need that for the USB transfer.

  It could be more ideal to connect the USB device directly to the host.  In this case

  (1) edit the VM and add a USB controller.  You will do this on the Hardware tab.

  (2) add a USB device to the virtual computer.  You'll also do this on the material tab for the virtual machine.

  Dave
  VMware communities user moderator

  ESXi Essentials free training / eBook offer

  Now available - VMware ESXi: planning, implementation, and security

  Also available - vSphere Quick Start Guide

• Satellite A60 - very slow USB transfer speed

  Hello

  I have a Satellite A60 with XP Home and the USB transfer speed is very very low. Is 2.0, but it is not working properly, because it takes about 30 minutes to copy the data from 1 GB on a USB 2.0 drive externally.

  I tried my USB drives on another computer and work quickly and well, so it is probably just a problem of drivers, but can't find them on the web from Toshiba to reinstall them. I heard that it is a common problem after installation of XP Service Pack 2, but I didn't do anything, I use the operating system as it came when I bought the laptop (with XP Home SP2 preinstalled original), I do not change any configuration or install drivers that can affect to the USB controllers and it has always been so slow.

  Could someone help? I tried to reinstall the drivers from Toshiba, but I think that there are not more special just for the USB, what should I update then? I need to improve the transfer speed of USB data for professional purposes, because I can't lose so given at the time of the transfer, please please please help!

  PS: Sorry for my terrible English, but it is there no Toshiba forums on my tongue: P

  Hello

  USB drivers are part of the operating system and you are unable to download the USB drivers separately.
  In my view, it is really not necessary to reinstall the USB drivers because the USB HDD is recognized correctly and it works.

  USB 2.0 transfer speed 480 Mbps supports and if any didn't error message then the USB ports running at full speed.

  For more details, please see this page of Microsoft;
  http://www.Microsoft.com/windowsxp/using/networking/learnmore/jones_02august05.mspx

  Last but not least I would recommend to update the XP to the last State. I mean that you need to install all of the available patches and fixes.

  Good bye

• USB/Bluetooth devices disconnection after Mac standby

  Hello world

  I am facing the problem that all my usb/bluetooth devices connected to my iMac disconnect all the time I want to wake up my iMac to the fashion watch. (I have to press the power button to reactivate standby). I noticed that this only happens when my iMac is idle for more than 2 hours.

  I am running Mac OS Version 10.11.2 on my 5 end of 2014 k iMac.
  I use a USB 3 Hub, Logitech C920, Logitech MX Master Aukey and the Apple wireless keyboard.

  I hope someone can help out me, it's so boring!

  1 reset the SMC, according to > reset the management system (SCM) controller on your Mac - Apple Support

  2. Open Bluetooth preferences > click on the Advanced... button > "Allow Bluetooth devices to activate this computer" is checked.

  (that should allow you to turn on the computer with your Apple wireless keyboard and possibly even the mouse Logitech)

  

  3 If your Logitech mouse is still not wake the computer Logitech dongle plugged on the USB 3.0 Hub... ?

  (try moving the dongle to one of the USB ports on the back of the iMac)

• HP Compaq 8100 Elite: Boot interrupted by the USB storage device

  If I have any sort of plugged when starting USB storage device, I just get a blank screen with a blinking cursor.

  I disabled each device start-up apart from the internal SATA hard drive and it still happens.

  Finally I found a BIOS update.

  On the HP consumer Support Site? NO.

  On an alley, ad - ridden, dirty pilots-for-all site.

  Anyway. It worked

• I have a problem with finding a PnP USB audio device when you search for available audio devices.

  Hello.

  I am building an application that can find a PnP USB audio device and play a tone if the device is connected. I am able to search audio devices using "Sound Device Info.vi" of the lvsound2.llb that comes with labview.

  The vi can find the USB device in good conditions, but there are problems - I'll try to describe 2 scenarios.

  1. the USB device is connected before 'Sound Device Info.vi' is called for the first time.

  In this case, the program can find the USB device. If I unplug it, the device disappears from the list of found audio devices. If I reconnect to the same USB port, it reappears in the list. It's all good.

  If I reconnect it however a new USB port, the device is not found. This is not good.

  2. the USB devices is not connected when 'Sound Device Info.vi' is called for the first time.

  "Sound Device Info.vi" is not able to find the device. Disconnect and reconnect does not make a difference.

  I'm under labview 2012 on windows 7.

  I am running the application as an exe to build.

  I call 'Sound Device Info.vi' as a 'call for reference"and the reference is closed between calls to the vi. I was hoping this would unload the dll used in "Sound Device Info.vi" and would solve the problem, but it didn't.

  Is there a way to reset the information usb labview during execution?

  Concerning

  Stephan.

  Hey Stephan.

  The sounds screws require a DLL located in:

  C:\Program Files (x 86) \National Instruments\LabVIEW 2012\resource\lvsound2.dll

  Internally, LabVIEW uses the DirectX API to enumerate devices. The one caveat is that probe us for devices when loading the DLL. We probe not later. So that it works for Bluetooth, USB, fire wire, etc. devices that can be inserted or removed at any time, you control somehow when this DLL charge and discharge. To do this, please see the following document:

  Dynamically that I can load and unload a DLL in LabVIEW?

  http://digital.NI.com/public.nsf/allkb/77594203D78D12278625729100758BE5

  I would also recommend that you provide a Kudo to this idea:

  Updated library lvsound2 (Sound Input/output Sound live) to support audio devices change on the fly

  http://forums.NI.com/T5/LabVIEW-idea-Exchange/update-the-lvsound2-library-sound-input-sound-output-V...

• USB MTP device drivers will not properly install for Samsung Galaxy S3 - Windows will not synchronize Galaxy S3 for computer

  Windows will not synchronize Galaxy S3 synchronizes a mobile computer.  When I attach USB cable the computer flashes added new hardware, but when you click the icon it goes in loops.  I've uninstalled and reinstalled the drivers in Kies and always the same problem.  All other cell phones synced to computer, including the Samsung Galaxy S3 but my iPhone no matter what I do.  When I open Kies and connect the USB cable there is no reconition of the cell phone.  I've seen a Code 31 error appear in good devices.
  Add questionnaires of the Add Hardware Wizard...

  SAMSUNG Mobile MTP Device (a yellow excamation sign)
               
  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  SAMSUNG Android ADB Interface

  This device does not work correctly

  SAMSUNG Mobile USB Modem

  This device does not work correctly.

  SAMSUNG Mobile USB Composite Device DeviceThis works correctly.

  This device does not work correctly.

  It is all the information I can give at the moment.  I forgot to mention I am running Windows XP I hope that helps also.  With everything says I don't understand why will not load the drivers required for this device.  For any help or suggestion will be greatly appreciated.  Thank you all

  Hello

  -What is the driver version you are using?

  The latest version is ver.v1.4.6.0 out June 19, 2012.

  I recommend you to please update the USB drivers on your computer and check if it helps.

  How to manage devices in Windows XP
  http://support.Microsoft.com/kb/283658

  If this does not help, I would recommend you to please contact Samsung support for assistance.
  http://www.Samsung.com/us/support/

  There is a community forum for Samsung where you can ask questions.
  http://www.Samsung.com/us/support/owners/product/Sch-I535MBCVZW

  Hope this information helps.

• Impossible to disconnect itself from USB storage devices

  Original title: USB storage devices

  Once more I couldn't properly disconnect a USB storage device because Windows tells me that a program is still using the device. There is no reason for any program to access it then why on earth isn't Windows the task/program name so that I can address the issue instead of having to restart my computer? Of the many irritants "characteristic" of Windows, it is one of the most galling.

  Hello

  ·        What is present in the USB key?

  ·        Since when are you facing this problem?

  ·        Remember to make changes to the system?

  I suggest you follow the steps mentioned in the article below and check if the problem is resolved.

  Advanced troubleshooting tips for General USB for Windows XP problems

  http://support.Microsoft.com/kb/310575

  If there is nothing important in the USB device, I suggest you to format the device and see if the problem still occurs.

  Note: If there is no important data in the USB then, back up data, and then format the USB.

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit ourMicrosoft answers feedback Forum and let us know what you think.

• How can I get the USB Audio device in option audio device for Windows XP?

  USB Audio will not appear as an option. However, the Audio USB headset is an option. Help. Thank you

  Hi VincentMr,

  ·         What is the brand and model of the USB audio device?

  You may need to install the device drivers on the device manufacturing site, or else you must have received the CD of the software with the device.

  See the following article for more information on the update of drivers:

   

  How to manage devices in Windows XP

  http://support.Microsoft.com/kb/283658

  Let us know the results.

• When a pop-up message indicates that a storage device has just been attached and I don't put a USB storage device into the computer at all, what that means?

  From time to time, (isn't that every now and then, not every day or every week) a message appears on the computer screen to notify that "a storage device has been attached... and something or other on a port '-as it would if a new hardware device had just been installed or removed... only, I have not attached at a storage device.

  In fact, apart from the scanner, printer and keyboard connected, which are already inserted until the computer is turned on, no USB storage device or any other thing seized or inserted into the computer when this message is displayed on the lower right screen where the icons on the desktop are,

  Why would this happen unless I had personally inserted/joint a USB stick storage device myself in my computer?

  I'm afraid that maybe someone to access details and store information from a remote location via a storage device? Is this possible?

  And if it's an error of some sort, how to fix this problem?

  Please notify. Thank you.

  This probably means you have a bad USB connection somewhere.  I got this a lot when I used markets good USB hubs.  It also happened a lot on a couple of the USB plugs on my old laptop 4 year, where I had plugged in and out things in them so that the connectors are not as strong as they were when new.  My main office more connected devices above that outputs 4 USB, that I had on the back, so I finally bought a card extension to add 4 more exits USB.  If this is your case, perhaps you could do the same.  Expansion cards are not very expensive, usually in the range of $ 15 to $ 25, and they are fairly simple to install.

  I hope this helps.  Good luck.

• Removed usb drivers Device Manager

  Hello

  I had a problem with the USB and Firewire connections on my HP XW8400 PC.  The system works under windows xp pro.  The problem I had was that some devices/readers etc were not noticed when I plugged the different Slots USB or firewire and others have been.  I have a dongle usb constantly on my system to run a publishing package that I use on a daily basis... I also have an attached Firewire/USB PCI card.  I use the rear firewire and slots of the editing software and hard drives USB and USB slots front is where I keep my dongle and I use the usb port and firewire for other devices such as readers, usk sticks, cameras etc etc.  As I say, things work well, other custom.  For those who don't to correctly connect the peripheral material Add Wizard would come upward, I press on to connect to the web to search for and then it they'd material device wzard found no drivers/solution/whatever.  Being that it is my main computer to work I didn't want to risk anything and so have put up with him for a long time.  However, these days, I need to get a camera connected to the said work stations and so made test after trying to install the software to factory for the camera via camera software CD and realizing that he did not always work.  I used Malware Bytes and it came with nothing and then AGV antivirus and it came wirth nothing.  Ok... So I thought that it MUST be something to do with the USB (and Firewire) themselves.

  I searched on google and it brought me to this microsoft support page: http://support.microsoft.com/kb/310575 I read through it and he said how to uninstall and re-install the usb via Device Manager drivers.  I went through the instructions and I have clicked on each of the usb devices in Device Manager and uninstalled.  Then I restarted my computer and when it said that it had detected new hardware everytime I clicked on the Hardware Wizard it now impossible to connect to the internet because one of the devices was my router to wide band.  GREAT!

  So, I spent half a day to find the original Windows CD and I reflected on the drive, but couldn't find anything to do with the USB drivers.

  I tried the last known good configuration and that was obviously after deleting files of drivers said Ihad closed and restarted a couple of times since then.

  I checked the system restore and that has been cut!

  If someone could please tell me how to install the said USB controller to ensure that I get the USB drivers installed?

  I'm guessing I now need to go through the window / each device and find the software CD and add the drivers, but I don't even know if I have half of the Conference on disarmament, or they just instantly connect via XP.  I certainly can't find anything for my router, which means I can't even on the web.

  And why has my material wizerd for usb and firewire devices summer miss me for so long?

  All advice appreciated.

  PS... Microsoft, don't you think not that 1 - it would be wise to let people know on the above mentioned page remove the usb drivers may well turn off your Internet so that the wizard doesn't work and you can visit his profile when you connect.  If she had said that I would never be deleted.  2. due to some software I use (Avid Media Composer) on the specially designed workstation, there are various conflicts that occur when the upgrade to Service Pack 3, so you stop the real users of microsoft products to have access to your DIFFICULTY IT thingymajig if they decide to stay on service pack 2.  Why make life so hard Micfrosoft?  I'm very careful with my systems.  I should have a choice of not having to be upgraded if it means he can endanger other packages, but I'll always freedom of basic set of tools and services that you offer.  I'm fed up.   The following, that I get computer is a MAC!

  You're right, that Windows XP has drivers for a large number of features built into the operating system.  Peripheral USB in particular are supposed to be 'plug and play' - you simply connect the device to the computer, it goes "Bong", and the device is recognized and installed.

  A "Repair Installation" window is supposed to leave all your applications and your data intact - but you will almost always see advice to backup everything that you care about the 'just in case '.

  Try posting here: http://social.technet.microsoft.com/Forums/en-us/itproxpsp/threads
  Technet forums are supposed to be for the "professional" so maybe, your message will be seen by someone who has a better knowledge of this issue than most people who post on the forums for answers.

  Items to include in your message:

  • You have XP Pro sp2 (and why)
  • That you have had a hard time to install a camera and so found and followed the instructions in KB310575
  • After you follow the instructions in KB310575, all of your USB devices are reports 1 Code and you are unable to install the drivers
  • Everything that you think is relevant
  • And, more importantly, a link to this topic, so anyone can see what's been tried so far: http://answers.microsoft.com/en-us/windows/forum/windows_xp-hardware/deleted-usb-drivers-device-manager/2272852e-7462-4d65-a8ad-e8162c9eb800#_self

  Good luck and I'm sorry, I could not solve your problem.

• What is a USB audio device and a Bluetooth HID device?

  What is the difference between a USB audio device and a Bluetooth HID device? Is there a difference? Different connection?

  My desktop computer shows the keyboard and mouse connections wireless in both places. I thought that I had to use the receiver provided with the mmouse and keyboard kit when I bought it and now I see it installed in two locations in the Device Manager. What does that mean?

  Hi jimafia,

  Let's start first of all, make sure you have software in place just in case you need more later.

  If they are the same exact drivers, it is possible that they have been installed twice, but the biggest problem is how much of usb devices you have connected?

  You can check and see when they have been installed in the properties for each driver.

  B Eddie

• Deletion of data (step by step) USB storage device

  I need to know how correctly, step by step, remove a usb port connected data storage device. I am currently using, Windows visit Home Premium. Thank you...

  By the clock in the bottom right notification area, you will find an icon. Hovering over it said something like 'remove hardware safely '.

  Double click on this button.

  Find the usb storage device in the hardware list.
  Select this device.
  Click on stop / remove safely

  Wait until you receive a notification that can be removed.
  Remove the USB port.
  If so, you can now safely unplug unit from wall outlet as well.

  I hope this helps.

• Using the USB audio device as default instead of analog audio ports

  Audio microphone USB installs and is listed in the devices under sound, video and portable with Dell computer game controller devices running Windows Vista, but the problems the system to use the USB mic as the default.  The sound devices list has also IDT HD audio codecs indicated, and the system will analog as the default input channels for the microphone, with no way to install the USB device.  Is it possible to put the USB audio as default microphone device?

  Hello RSA 456,.

  Many sound problems are caused by hardware that is not configured correctly. We will check your sound card, connect the cables in the correct locations, ensuring that the material has the power and the verification of the volume.
  Please follow the method described below to solve the problems.
  Method 1:

  1. plug your USB microphone.
  2. the LED will light to indicate that it is powered USB.
  3. Windows will automatically detect the USB Audio device and install the universal drivers.
  4. to set up your microphone as default device USB Open Control Panel.
  5. Select display as a classic view of your control panel, then select Select Sound.
  6. click on the recording tab. Here your USB Microphone will be listed.
  7. click on the USB microphone. If there is no checkmark beside the USB Microphone, click on set as default.
  8. the default device is used in most programs such as tape recorder simple registration.

  Method 2:
  Please click the link below to check how to check if the hardware works just fine.
  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows?T1=tab02

  Kind regards
  Sooraj.S