Use HREAP SSID and vLAN

Similar Questions

• 2 SSID and VLAN on each access point

  I'm new to Setup IOS APs and wireless, in particular, a couple of 1142Ns in autonomous mode and are looking for answers and examples. These APs will be connected to the POE on an ASA 5505 firewall ports. I also set up the 5505.

  The requirements are that each AP have a SSID 'internal' and 'external' and each AP will have two VLANS.

  The APs should allow roaming between them.

  Internal SSID will allow full access to the company's internal network and the Internet and will use WPA2. It will use the corporate dhcp server and the dhcp server to use IOS to distribute addresses.

  The external SSID will not have access to the Internet and use WEP. The ASA 5505 provide dhcp on these clients.

  The two ports PoE on the ASA 5505 will be shared resources for inside and dmz VLAN.

  If anyone has examples of any of these conditions, observations or similar config they are willing to share, please post them.

  In particular, I would like to see an example of homelessness config Setup VLAN, SSID config and Setup WPA2 and WEP.

  Thanks in advance.

  The link below will help you get the configuration based on the AP wireless...

  http://www.Cisco.com/en/us/Tech/tk722/tk809/technologies_configuration_example09186a008055c39a.shtml

  Here is the link for PSK WPA-2 as well

  https://www.Cisco.com/en/us/Tech/tk722/tk809/technologies_configuration_example09186a008054339e.shtml#pers

  The above can help you...

  Concerning

  Surendra

  =====

  Please do not forget to note positions that answered your question or was useful

• ACS 5.3 use LDAP. for one SSID and use IS HOST. for a different SSID

  I have 2 SSID on WLCs

  I wish I had 1 point SSID to the radius of the acs using LDAP store and the 2nd point SSID to the radius of the acs using identity store of the host for mac filtering.

  both scenarios are working, but not all.

  If I set the order of the rule I can get an SSID, but then the other fails.

  Authentication failed                                                                                 :

  22056 object was not found in the identity of the point of sale.

  Access matched Service selection rule:	Rule-1
  Comparative political identity rule:	Rule-1
  Some identity stores:	RBLDAP

  Evaluate the politics of identity

  15004 Matched rule

  15013 selected identity store-

  24031 sending request to the primary LDAP server

  24017 Looking up host in LDAP - 04-xx-xx-xx-xx-xx Server

  24009 host not found in the LDAP server

  22056 object was not found in the identity of the point of sale.

  22058 advanced option that is configured for a unknown user is used.

  22061 the option 'Refuse' Advanced is set in the case of a request for authentication has failed.

  11003 returned RADIUS Access-Reject

  If I move the mac add rule before the rule of ldap, but then the ldap authentication fails

  Request for access received RADIUS 11001

  11017 RADIUS creates a new session

  11027 detected host Lookup UseCase (Service-Type = check call (10))

  Assess Service selection strategy

  15004 Matched rule

  Access to Selected 15012 - MAC filter network access service

  Evaluate the politics of identity

  15004 Matched rule

  15013 selected identity Store - internal hosts

  24209 Looking internal host IDStore host - 04-xx-xx-xx-xx-xx

  24211 found internal host IDStore host

  Authentication 22037 spent

  I tried to install the following without result.

  It seems to me that there should be a simple process to do what happens. I thought that if the rule does not match it would be to move on to the next rule etc...

  I might be able to live with the first ldap control and if it does not pass to the db of the local host, but seemingly ineffective.

  https://supportforums.Cisco.com/thread/2133704

  You can create a sequence of identity store so that if the end point is not present in the ldap database, then it can check its database of the local host.

  Or you can create a condition in your selection of service such as if rule called-station-id ends with (AIDS) then you can have it match the rule that uses the appropriate rule pointing to ldap, another rule when called-station-id ends with (ssidB) match the rule that points to the rule that uses the database of the local host.

  Here is the section on the configuration of the sequence of identity store, don't forget to select continue if user not found.

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_sys...

  Thank you

  Sent by Cisco Support technique iPad App

• Existing vSwitch using and VLAN

  Hello

  I was wondering if it was possible to configure Lab Manager to use an existing vSwitch and VLANS configured in vCenter rather than create its own switch and VLAN?

  Thank you.

  Unfortunately not.  You will need to let LM create and manage their own groups of ports or switches.

  Note that:

  -When you bind a physical network to a vSwitch/vDS, LM creates a port group to represent the network (it also has an 'LM' tag in vCenter)

  -If you deploy a configuration "reserved", he made a vSwitch or vDS port group to represent the fence... and limit network traffic.  Again, when you look in vCenter, there should be an 'LM' tag to the object.

  Kind regards

  Jon Hemming, b.SC., RHCT, VMware vExpert 2009
  http://Twitter.com/vJonHemming

  If your question or problem has been resolved, please click the "right answer".  If someone helped him, please click "useful answer.

• Unique to the multiple SSID and possible access point single channel?

  Hello world.

  I have a silly question.

  Let say, we have three VLAN, vlan1, 2, 3 and they are mapped to the following wireless LANs:

  VLAN 1 ssid1

  VLAN 2 ssid2

  Vlan3 ssid 3

  AP - trunk - dagprogramm network.

  Our access point has mobile devices in three local wireless networks, IE ssid1ssid2 and ssid3

  Since the mode AP use half duplex, mobile devices need acknowledgement positive to ap they can send data, so once channel let channel 3 (assuming that 802. 11b is used) can be shared by all the devices in three local wireless networks.

  My understanding is correct?

  Thanks and a great weekend.

  An access point = an associated action related channel and each ssid and the customer that one channel and the AP is essentially as a hub

  concerning

  Joe

• Need help creating Unique SSID and secure network

  My AP has been recently reset the SSID I had chosen has of course been erased and AP is now considered to be "linksys". It also now broadcasts as an open network.

  I tried to create a new network using the Intel PROSet/Wireless graphical user interface that came with my PC and it allows me to create a SSID and put a password on it, but it does not affect the real "linksys" network even if I would have erased "linksys" in the text box and enter my own.

  I tried in vain to reset the AP again and connect to 192.168.1.245 using IE and firefox, I get an error loading page every time. I have also tried to set the IP address of my PC to the same meanings and the subnet by default 255.255.etc and could not connect.

  I also tried to connect the AP to the pc directly, what does not work.

  What I am doing wrong.

  PS. I don't have the original installation CD, I think it would be solved.

  I managed. Thank you!

• How can I find the network name (SSID) and the chain of security for my network

  I have a wireless network with a printer on it - even if the printer is connected with a wire.  I want my laptop to be able to use the printer wireless to another room - instructions for putting in place early yb requiring the SSID and the security chain.

  Hi petetyler81,

  You can connect to the router manufacturer's website and make sure that the SSID and find the string, otherwise you can contact the manufacturer of the router and check.

  For more information, see the link:

  Setting up a wireless network

  http://Windows.Microsoft.com/en-us/Windows7/setting-up-a-wireless-network

  Hope this information is useful.

• NFS and VLAN native

  Hi all

  I have two channels of different port by interconnection fabric. On a single port channel I have several VLAN assigned to the traffic of the virtual machine so that 1 VLAN by default not identified in a vNIC. Unfortunately, in our factory environment VLAN is used for certain traffic of virtual machine. Now, on the second channel of port it is connected to nexus 5 k switches but only allowed for a NFS VLAN.

  The problem I am facing is that if I enable NFS port channel, some of my traffic to the machine virtual stops as it seems that they arrive via public port channel but are trying to wind up with the NFS who filed the application.

  I want to use the Group feature VLAN to apply a VLAN for the Port Channel Mapping. I am able to associate a rule for NFS fine, but I'm not able to select the default VLAN in my public group to create a mapping rule.

  If I just create a group for NFS, be it re - automatically send everything through the other channel of port? (This is essentially what I want) Or if I create a group and not the second, it will only help the NFS one but leaves the audience in the same situation that bounce between several channels of port?

  Thank you for your help and assistance

  Contact me directly if necessary

  an a v v a l i t o r o n t o c a.

  Hello

  Altogether, you created 10 vlan, including the vlan by default and you are able to add only 9 vlan in this group...

  You mean that you want to add the vLAN by default Id in the particular group which was created by you...?

  You cannot add the vlan by default Id in groups of VLANs, but an option is there you can change the default vlan ID 1 to another number, you can create a new id vlan 1 and you'll be able to add to the group.

  Before making changes to ensure that if id vlan by default 1 used by some other servers or not because if you have changed this means it will disrupt traffic.

• Subinterfaces and VLAN

  Hi all

  I was hired on with a State... Now its been awhile, but I do not remember how subinterfaces and VLAN all link together!

  Now correct me where I'm wrong (please), but them VLAN is created on the correct first switches?  When you create a VLAN on a switch you don't need ip or gateway address by default because them VLANS are the switch.  If you want intervlan routing you need a router.  Then, you configure a port trunking between the switch and router (ISL, 802. 1 q).  Now in the router, you can create a VLAN, and here you inter the ip subnet or the default gateway addresses correct?  This is where I get confused as to what reasons do you need subinterfaces?  How they roped VLAN and what would be the logical flow of data?

  Anyhelp would be appreciated!

  Yes you are right. If you are using the layer 2 switch and want to make the intervlan Routing then you need Layer 3 router device. But you must configure the interfaces sub with the default gateway to route traffic. Because there is a single trunk between swich and router so we need sup interfaces for multiple VLANs.

  Interface FastEthernet0/0.1

  Encapsulation dot1q 10 (10 represent 10 ID VLAN)

  10.1.1.1 IP address 255.255.255.0

  If you use a layer 3 switch, then you point all sub interfaces need so then you can create the interface vlan with the default gateway. You must enable ip Routing.

  Interface vlan 10

  10.1.1.1 IP address 255.255.255.0

  Hope this will help.

  Please rate if this can help.

  Thank you

• VPN and VLAN

  We have a site divided into 2 IEE802.1Q VLAN, using no switches Cisco. They have a PIX515 for Internet access. It is also configured to provide inbound VPN access for management and general purpose of access.

  In principle it is possible to set up a new VPN connection which is reflected by its interior traffic be tagged with a specific VLAN ID while all other traffic (including other VPN connections) remain without a label?

  If the PIX ends your VPN from the outside that the answer is no. If the VPN is coming from outside, and ending at the PIX she never travels a VLAN. VLAN tagging is used to identify what VLAN came from a source image and what VLAN it is intended for a current switch vlan can 'route' frame through the appropriate VIRTUAL LAN. Why you want to tag from outside VPN traffic? If it's to control access, you can specify 2 VLANS and VLAN 3 on the PIX (as long as it has code 6.3) and control what VLAN, you want that each group VPN access to through the use of the ACL. Each VLAN on a PIX is treated as a physical interface. It has its own security prefs (0-100) and can have ACL applied to them as well as the physical interfaces.

• Management and Vlan native in different subnet?

  Can I have a management ip and vlan native in a different on AIR-1242 switch subnet and 2960?

  Native on switch = 1.

  The interface vlan 100 = 10.10.1.25X 24

  BVI ip to the vlan 100 = 10.10.1.25X 24

  -HM-

  Hello

  As far as I know, the management and the native will be the same... I guess... You have Vlan native as 1 on the switch and Int Vlan 100 on routing switch? Am I wrong? Let me know what are your needs... which will help me to help out you!

  for your question...

  Normally, we specify him vlan native on the switch and the AP so that communication happens... communication won't happen if there is a match of...

  Looking forward to hear from you!

  Let me know if that answers your question...

  Concerning
  Surendra
  ====
  Please do not forget to note positions that answered your question and mark as answer or was useful

• SSID and what windows 7 called wpa - psk [tkip] + wpa2-psk [aes]?

  I'm trying to get a new laptop for windows 7 to connect wireless to my existing home network which consists of a computer laptop xp (wireless) and a desktop of vista (cable) and a netgear router.

  I'm looking at a dialog box (on the computer laptop windows 7) named "manually connect to a wireless network.

  (1) the dialog box wants a "network name".  What is often called a "ssid"?

  Said (Routeur Netgear my 2), under Security Options ', use "wpa - psk [tkip] + wpa2-psk [aes]", but this isn't an option in the dialog of windows 7.  The choices in the dialog of windows 7 are wep, wpa2-personal, wpa-personal, wpa2-enterprise, wpa-enterprise and 802. 1 x.  What is windows 7 equivalent of "wpa - psk [tkip] + wpa2-psk [aes]"?

  Thank you, Bob

  I'm trying to get a new laptop for windows 7 to connect wireless to my existing home network which consists of a computer laptop xp (wireless) and a desktop of vista (cable) and a netgear router.

  I'm looking at a dialog box (on the computer laptop windows 7) named "manually connect to a wireless network.

  (1) the dialog box wants a "network name".  What is often called a "ssid"?

  Said (Routeur Netgear my 2), under Security Options ', use "wpa - psk [tkip] + wpa2-psk [aes]", but this isn't an option in the dialog of windows 7.  The choices in the dialog of windows 7 are wep, wpa2-personal, wpa-personal, wpa2-enterprise, wpa-enterprise and 802. 1 x.  What is windows 7 equivalent of "wpa - psk [tkip] + wpa2-psk [aes]"?

  Thank you, Bob

  SSID is the name of the network. His need if you manually configure a wireless connection.

  WPA-Personal = WPA - PSK (TKIP)

  WPA2-Personal = WPA2 - PSK (AES)

  http://en.Wikipedia.org/wiki/Wi-Fi_Protected_Access

  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-different-wireless-network-security-methods

  This means that you can use or plan on different customers, IE. PC - A uses WPA-Personal while PC - B uses WPA2-Personal, and the router that will allow them to connect assuming the encryption key and password / password is correct. You can probably configure the Netgear for only WPA-Personal or WPA2-Personal. WPA2-Personal is the best from a security point of view. FWIW I have the same settings on my wireless Belkin router, IE. its configured for WPA - PSK + WPA2 - PSK. In my case, I only use WPA2-Personal on my wireless clients and simply never taken need to configured the router to only use WPA2-Personal.

  http://theillustratednetwork.MVPs.org/LAN/SoHoWirelessSecurity.html

  Instead of manually configure the network you can watch this...

  http://Windows.Microsoft.com/en-us/Windows7/view-and-connect-to-available-wireless-networks

• Assigning the SSIDs to VLANs

  I installed AP1200 12.2.15 IOS running and I want to know if I can give more than 1 ssid for each vlan.

  Thanks in advance

  Hello

  Currently, you can have only 1 SSID per vlan. In a next version of the IOS, we will start supporting multiple SSID. Will not be released before the end of January.

  Kind regards

  Aaron

• With the help of VLANS and VLAN Tagging is not working / no connection

  Hello

  I m trying to configure a VLAN between some virtual machines on ESX host 3.

  I want to do this way:

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 1004074

  I got 1 dedicated NETWORK adapter to each ESX host that is connected to a dvSwitch in which I configured a portgroup

  with VLAN ID 2121. I have configured each virtual machine to use this network.

  When I put the virtual machines on a single host, they are able to communicate.

  When they are placed on different hosts they are (if the VIRTUAL LAN is enabled on portgroup) not able to communicate.

  So I m assuming it must be a problem in the config NIC on the ESX host or switch.

  I m using a HP2910AL on which I activated mode trunk for each port that is connected to a NETWORK card with

  the dvSwitch/Portgroup I try to use for the vlan. In the hp switch, I have a default VLAN with ID 1 where

  the Ports are marked not signposted. I install a second VLAN on the switch with ID 2121 in which I scored

  This tag ports.

  Is there something else to do - perhaps side ESX host?

  I tried changing the settings as "forged transmission-> allow ' on portgroup and I found other things

  in the web, but always without success.

  Kind regards

  Patrick

  Were you referred to this guide? :

  http://CDN.ProCurve.com/training/manuals/2910-ATG-Feb09-2-VLAN.PDF

  "show vlan ports" would be my next check to make sure that you have connected to your ESXi host 3 ports in the vlan 2121.

  As Duncan has said if you have a VLAN ID on the portgroup in the vSwitch and you have the port on the pSwitch as trunk not acess and VLAN ID is allowed on the trunk port pSwitch you should be ok.  Just to clarify the trunk is 802. 1 q No 802.3ad.

  The reverse is not VLAN ID on the portgroup vSwitch, use coelio on pSwitch with VLAN ID.  Limited pSwitch port to a VLAN, this may be ok for you?

• OfficeJet 6000 E609n - Wireless concludes SSID and secure network but will not connect

  I use Mac OS 10.5.8. I installed the printer for USB and went to the next step to configure wireless. My secure network, it obtains the SSID and then asks the WPA personal password for the network. I enter this and click on continue and the message comes back, "the Wi - Fi network selected «...»» ' is not within reach of the unit. ' Button choices are 'Change network' or 'Retry '. Despite attempts unsuccessfully repeated. However, I scanned for other networks and found a secure and connected to this network. Go figure. My router is sitting on my desk next to the printer. The router is a D - Link DIR-655 n I'm on cable for ISP services. When I first bought the printer, we were away on vacation, and I've successfully added to my Mac laptop. I have reset the printer found in the then successful and user guide to establish a connection to the House, with the unsecured network (I don't live in a condo so no idea whence the other network). Thank you.

  You can try to update the firmware on your router.  Some of these models have had problems with HP printers and Netgear was subsequently fixed it with a new version of the firmware.