using Vista, I get a message that I have "limited access" wireless
I have Vista on one of my laptops, I started to use it more as a problem occurred on a laptop more elderly with XP on it. With Vista, I get a message I have connect to my router wirelessly with a limited access wireless. This will show me deservi not able to get on the internet. It works fine when I connect an ethernet cable to it. Any ideas of what I can do?
Hello
A message in the small window that says connected wireless does not mean that you really have a valid functional connection.
Above everything is OK, you must be able to connect to the wireless router. (WIFI hotspot).
Linking the means of router you can enter the IP base of the router in an address bar in one go, being able to connect, see and configure the router menus (extended to the wireless router manual should explain how to do).
If it will not connect to your wireless router, journal newspaper from any computer that can connect to the router wirelessly with a wire, disable wireless security, make sure that the wireless SSID broadcast is enabled and try to connect with no. wireless security.
Enable security wireless after you eat to make a functional connection.
----------------------------
The wireless card drivers much also install utility wireless of the seller.
Make sure that if there are teas from Wireless Utility of seller does not work with the native Windows wireless utility (Service WLAN).
----------------
Firewall software can block traffic Local to the network that you are trying to use because it is not set to the network Zone Trust.
Make sure you firewall No. preventing / blocks wireless components to join the network.
Some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible set up the firewall correctly, otherwise totally uninstall and get rid of its remaining processes that permit the own local network traffic flow.
If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .
party like Hello and NetMagic 3rd network managers can block local traffic too.
---------------------------
Stack TCP/IP (network IP number) of work should look like.
Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.
http://www.ezlan.NET/Win7/status-NIC.jpg
Description is the data of the card making.
The physical address is MAC of the card number.
The xx must be a number between 0 and 255 (all xx even number).
YY should be between 0 and 255
ZZ should be between 0 and 255 (zz all the same number.)
The date of the lease must be valid at the present time.
* Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.
* Note 2. There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.
Jack - Microsoft MVP, Windows networking. WWW.EZLAN.NET
Tags: Windows
Similar Questions
-
I currently have an ad - one that I use frequently on IE8 which does not work on IE9. How can I stop to get a message that I have new updates when IE9 is the only update?
Hi altak38,-What is the add-on which you speak?-Are you referring to Windows Update with Internet Explorer 9 update several times even if it has been installed?If so, follow the steps in the following article to resolve this problem.Post back with more information for the issuance of the add-on - to help you help. -
I unplugged and plugged everything in again, but I still get a message that I have to select a printer. The printer is selected as the default printer and the status is ready, but I still get the same message. Help!
Try to select a different default printer and then back to the right printer and reset it by default and see if that helps.
If this does not work, please transfer your question in the Hardware Forum: http://social.answers.microsoft.com/Forums/en-US/vistahardware/threads.
I hope this helps.
Good luck!
Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.
-
Get rid of PC Cleaner
I'm trying to download Security Suite from my provider and I get a message that I have to get rid of PC Cleaner. I searched my PC and that you do not find PC Cleaner. If I don't know how I'll remove it. Thanks for your help. The only reference to PC Cleaner is the Microsoft Security on the PC.Go to add/remove programs and see if PC Cleaner is in the list. If so, then click to remove.
Then go into Windows Explorer. Research on Windows/System32 and see fi there is pcsd.dll and delete it.
Then go to regedit and search for any mention of PC Cleaner, PC Cleaner and remove these entries.Change the settings of the REGISTRY can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the REGISTRY settings configuration can be solved. Changes to these settings are at your own risk.
Let us know if that helps.
Marilyn
-
I get a message that I have 25 pilots who need updates.
Original title: Why will not be up-to-date windows free drivers as they do for free windows dates
I get a message that I have 25 pilots who need updates. I can't afford to pay for driver software to have the update done. How is the windows updates are free.
I don't know what to do.
Mary
Hello
Driver software is provided for free.
You tell us how you get this message on the drivers.
Updates of Windows was designed for performance issues and updated and of security Windows Update Microsoft hardware drivers, not 3rd party hardware.
Microsoft normally does not have the latest drivers available as Microsoft relies of the 3rd party hardware/computer Manufactuers to provide.
You must get your software driver from your computer or hardware manufacturer, not through Windows Update.
Access the site on your computer or equipment manufacturing > Driver and Software Support Section > search your computer or hardware model number > then your operating system > locate the correct drivers > download and install.
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
If you receive this message, and he asked for money to update the drivers, scan of Malware:
Download, install, update and scan your system with the free version of Malwarebytes AntiMalware:
http://www.Malwarebytes.org/products/malwarebytes_free
See you soon.
-
why I always get the message that I have a free membership, when I have a subscription?
I would like to know why I always get the message that I have a free membership, and I need to improve my creative to a full, membership cloud membership even if I continued my membership in January
Please see the suggestions here and see if they help you:
FAQ: What should I do if I have a subscription, but my application acts as if I had a trial?
If if still appears under the name of first instance, after trying these suggestions, please contact our staff of support directly by following this link: contact Adobe customer service.
For more information, please visit: FAQ: how to contact Adobe for support?
-
I installed lightroom via a dvd and when I was asked to fill in the serial number I have done a few times. now, I get the message that I have to disable LR on the other pc, I don't have one... then what can I do?
You are welcome!
-
I try to install CS6 on my new MacBook, but I get a message that I have to close SafariCloudHisto and SafariNotificati. I have nothing open safari form then what is?
Hello
Please see the Installation of Adobe Acrobat asked to close "SafariNotificati"
Hope that helps!
Kind regards
Sheena
-
I'm not able to use Firefox Hello. I get a message that it is not available in versions of Firefox ESR. How can I change my version of Firefox? I'm a home user and when I click on the link update my personal version of Firefox I get a message telling me I have the latest version. So, I'm stuck. I also used to have a link to beta "Hello" when it first came out (he was working at the time). This link is now expired. Can someone help me understand how to establish access to 'Hello '?
Hello will also work where you have configured firefox to run in permanent private browsing mode ("never remember history" in options > Privacy panel).
-
had 2 users on the computer with itunes on the desktop. main user itunes has stopped working, but the secondary users still worked. tried to update software with the latest version but get a message that reads "not access network location % data%\ app.
This problem occurs because there is incorrect entries in the Shell folder of the user who is logged on to Microsoft Windows. When Windows Installer goes to the sale of Shell folder of the user who is logged on to the computer, Windows Installer cannot locate the correct entry. The solution is in http://support.microsoft.com/default.aspx/kb/886549.
The steps to correct this problem involve editing the Windows registry. Change the settings of the REGISTRY can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the REGISTRY settings configuration can be solved. Changes to these settings are at your own risk. I suggest that you first back up your registry as follows: http://windows.microsoft.com/en-US/windows-vista/Back-up-the-registry way to create a point in http://www.howtogeek.com/howto/windows-vista/create-a-restore-point-for-windows-vistas-system-restore/ restoration system just to be on the safe side.
Here are the steps to fix it.
1. click on start, run, type regedit in the Open box, and then click OK.
2. look for the following registry key:
HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Explorer\User Shell dossiers\
3 remove the entries that show the path that is listed in the error message.
886549 KB http://support.microsoft.com/default.aspx/kb/886549: Regedit open again. In the left pane, click User Shell Folders, point to new, click expandable string value, type the value name that you want to restore (AppData) and then press ENTER. Right click on this value, click change, type the value in the value data for the value name box, and then click OK. The value data must be: % USERPROFILE%\AppData\Roaming. Change it if necessary.
Step 8 KB 886549 suggests that you also check the values in HKEY_LOCAL_MACHINE\Software\Microsoft\Windows\CurrentVersion\Explorer\User Shell Folders. However, by fixing my problem, I had not to change values in the registry key. If this does not work without the full procedure, follow ALL the steps in the referenced article.
I hope this helps. If not, post back with the results of what you tried. Rear post anyway so we will know what happened.
Good luck!
Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.
-
* - Original title - Win7 settings
This is related to other issues on Win7 Aero performance. I have a Core i5 processor 2310 2.9 GHz CPU and a videocard from ATI (AMD) Radeon HD 6570 (I don't know the exact specifications but minimum memory for this model is 512 MB). Well, this should be enough to use Aero. However, when my PC comes out of hibernation, I get a message that the settings have been automatically changed because of not enough memory for operation Aero. Why is it so?
Hello
1. have you made changes on the computer recently?
2. is specific to hibernation question?
3. What is the accurate and complete error message?
Method 1.
Open the Aero Troubleshooter: http://windows.microsoft.com/en-IN/windows7/open-the-aero-troubleshooter
Guided Help: Troubleshooting Aero in Windows 7: http://support.microsoft.com/kb/976170
Method 2.
You can try to change the power settings and check if that helps.
Power management: http://windows.microsoft.com/en-us/windows7/products/features/power-management
Method 3.
You can also update the display drivers and check.
Update a hardware driver that is not working properly: http://windows.microsoft.com/en-hk/windows7/Update-a-driver-for-hardware-that-isn ' t-work properly
Refer.
Sleep and extended: frequently asked questions: http://windows.microsoft.com/en-us/windows7/Sleep-and-hibernation-frequently-asked-questions
I hope this helps.
-
Administrator permissions
I am logged in as administrator. When I try to move the files from drive c to e drive, I get the message that I currently don't have permission
to access this file.As an administrator, I though I had permission. How can I fix it?
I've only logged on as administrator.
Even logged on as administrator, you have not all privileges unless you raise them. This is done to prevent malware to take control of your computer when logged in as an administrator.
What files you try to move?
-
How can I fix the error message that reader Multimedia Keyboard stopped working. My keyboard is a
0817-gateway model # KB.
Hello
I suggest you to follow these steps and check if that helps:
Method 1:
Start the computer in safe mode and check if the same problem occurs:
http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-modeMethod 2:
If it works fine in safe mode, and then try to perform the clean boot and check if it helps:
http://support.Microsoft.com/kb/929135NOTE: When you are finished troubleshooting, make sure that you reset the computer in start mode normal such as suggested in step 7 of the above article.
It will be useful.
-
get the message that I have a flow of 115 online
While im on a Web site like poker deluxe on the Trombinoscope, I get a message saying that I have a flow on line 115 what does that mean
Hello denniscombs,
The problem is related to the Web site that you use. It is not a windows problem. Contact the webmaster of the site because there is a problem with their coding that needs investigating.
See this link: http://grownupgeek.com/stack-overflow-line-115 for more information on the problem.
This forum post is my own opinion and does not necessarily reflect the opinion or the opinion of Microsoft, its employees or other MVPS.
John Barnett MVP: Windows XP Expert associated with: Windows Expert - consumer: www.winuser.co.uk | vistasupport.mvps.org | xphelpandsupport.mvps.org | www.silversurfer-Guide.com
-
Reactivation of my professional Windows
I have a professional windows. I installed it on my Mac and I uninstalled it. But of course I have registered more than once in that it is the machine, but I uninstalled. But now I have an office and I want to use windows profesional in it. Now, when I tried to activate it, it said I crossed my activation limit. Not use it in any other machine. And if we use it in any other machine that I need to disable and want to turn it on in my office.Please give me a solution for this.Thanks in advanceIf it's a full license or upgrade of detail - you can move it to another computer as long as it is installed on one computer at a time (and if it's a version upgrade Windows the new computer must have its own license of qualification).
Have you tried using the activation of the phone and talk to someone?
To contact a Microsoft customer service representative to activate Windows by phone, follow these steps:
- Click Start, point to programs, point to Accessories, point to System Toolsand then click Activate Windows.
Or, click on the Activation of Windows icon in the notification area. - Click on Yes, I want to telephone a customer the service representative to active windows now.
- Click read the Windows Product Activation privacy statement, click new, and then click Next.
- Follow the steps in the Activate Windows by phone dialog box, and then click Next.
- When you are given a number and call don't select any option and wait for a person pick up, then explain what happened.
The American phone for activation number is 1-888-725-1047
How to activate XP:
http://support.Microsoft.com/kb/307890 - Click Start, point to programs, point to Accessories, point to System Toolsand then click Activate Windows.
Maybe you are looking for
-
Problem with VPN. Router is not encrypted but decrypts
Hello, I have a problem in my IPSec tunnel. One of the routers (Cisco 861) is not encrypt the packets but decrypts those incoming from the remote peer (RV042). In the access list for the wan interface I deny traffic between subnets and vpn access lis
-
I always just drag her in the chronology of the sequence and SUDDENLY todayIt won't let me, so I don't know what to do? Please help anyone.It's the first time I ever went to a second sequence and I useimages from the camera even as the first sequenc
-
Yet the startup error code: 1
Hello. I have a problem. When I start again I get an error: "Configuration error, please reintall the program" I have reinstall but it did not help.Pre-training system:-Windows 7 64 bit Service Pack 1Please help really is important!(Polish language)E
-
Options format when you save a jpeg file
What is the difference between ' basic', 'Basic optimized' and 'Progressive' and what is best for each option?
-
Why is the fee up to $49,99 $ 29.99?
Why is the fee up to $49,99 $ 29.99?