V313 all-in-one not scan after upgrade to Yosemite on Mac

Similar Questions

• My PSC 1210 all-in-one not Scan after the recent software update

  There is no if long software update asked me to install the last change of HP software. Which is curious, because when I look in the download, the last of them for OS10.6 section, which I run, was released in 2009.

  Before, I scanned successfully by using the Print & Fax system preferences.

  When I did it today, thogh, after choosing the option to Scan and then open Scanner, I would get the message that there is 'no scanner not selected', although HP psc 1200 series at the top of the screen. I tried scanning several times and got the same result every time.

  What can I do to get this working again?

  Hmmm, that seems strange that you will receive an update for a PSC 1210, because I do not think that there has been updates this software for years.

  Have you tried to uninstall the driver and then reinstall?

  You can find the instructions to uninstall here: http://support.hp.com/us-en/document/c02259020

  And then re-install the driver by clicking on: http://h10025.www1.hp.com/ewfrf/wc/product?cc=us&dlc=en&docname=c02259020&lc=en&os=219&product=90764&sw_lang=

  Click on drivers & downloads and select your operating system (Mac OS X) from the drop-down list and click Next.  Expand the sign next to the driver - product Installation software (8) + and then download/install the driver for 10.6.

• Help! -Acer Aspire all-in-one touch screen after upgrade Windows 8 Pro

  Hi all!

  This is a rather confusing questions and about * me off no end!  I know that some of you may have encountered this already and could have a potential solution?

  I have an Acer Aspire all-in-one, AZ5101 (Aspire Z5101), with 4 GB of RAM, etc..

  Since the Developer Preview of Windows 8 came out, I've been running Windows 8 perfectly.  I completely uninstalled (each time itself) and run the following:

  Windows 8 Developer Preview, 64-bit

  Windows 8 Preview of consumer, 64-bit

  Windows 8 Preview, 64-bit version

  In any case, on this PC worked perfectly - y INCLUSIVE of the TOUCH SCREEN.  I never had a problem.

  So far so good.  Then, they finally released updates Windows 8 Pro official licensed by download.  I bought the upgrade and downloaded.  Just like in * ALL * other cases, upgrade, I chose "keep nothing" of the old system (I never really got all the important data on here), and do the upgrade itself.

  After the upgrade was complete, and ALL Windows 8 Pro updates have been applied by Windows update, I have a system where the screen is clear and precise, everything works, and all devices in Device Manager, show the Greens well, it works fine - NO ERRORS.  HOWEVER - NO CONTACT!  No touch no screen function at all.  The screen now has this time as a standard monitor.

  I tried the driver Idéacom - no luck.  Anyone know (please? LOL) how to get the touch screen to work again?  Thank you very much!  I really appreciate any help you can give.  Microsoft technical support had NO idea and no reply emails from Acer! Laughing out loud

  Thanks again,

  Mike

  [edited to conform to the guidelines]

  Hello Mike

  I sent the pilot. Please test and advise.

  Kind regards

  FReeZA

• Photosmart C6188 all-in-one not scan on the mac with OS 10.6.1

  I just bought a new mac with snow leopard and incapable of having the C6188 HP photosmart all in one analysis images on mac.

  I made the mistake of installing the original software which is come with the printer, and then discovered that it does not get. So I uninstalled the software and performed an update to the Apple software.

  I tried according to your publications/announcement about the leopard snow, preferably using system preferences and applications of image capture.  I can print all right, but unable to scan images on mac.  I get the error message is ' year error occurred while communicating with the scanner.  It's the same message that I get from all three applications (preferably, preferences system and capture image).

  A big thank you to all who can help...

  I'm glad it's working for you now.  Multiple page in one file is a driver problem.  Sorry, you will need to wait for an update.

  In the meantime, it is very easy to combine pages in a file (pdf) with preview.

• PSC 2355 all in one printing stopped after upgrade windows 8.1 scan is OK.

  I have a HP psc2355 printer worked happliy in window 8. I downloaded and installed windows store 8.1 and the printer no longer works!

  With the printer Open (via Control Panel) status window, the details of the document briefly appear when you click the button print. Nothing happens at the end of the printer. Theres nothing wrong with the printer as I can use it on another PC without problem.

  I uninstalled and reinstalled the printer using hppiw 2012-10-31 and the HP print and Scan Doctor V 4.1.0.29 which gives an error in device "your printer is in a busy state" after an attempt is made to print from applications or properties of the printer/print test page.

  that self-test prints OK.

  Scanner works OK

  Printer is connected via rirectly USB cable to the USB port on the PC

  Windows Update ran this morning

  3 hours lost so far!

  SOLVED * printer properties Advanced tab Print Processor change Print Processor to winprint hpzpplhn settings check the default data type is RAW print OK now HP has gotten support jobs going?

• HP Scan does not scan after upgrade of the Lion

  I upgraded to a Lion for Snow Leopard and followed the instructions of HPs (uninstall, reinstall the driver for 10.6, Lion install update). Now HP Scan can't find my scanner (Scanjet 4370).

  OK, we can expect about resetting the printing system, but I got lucky with sweep because digitization will in fact through this system (note that it is called Print & Scan in the Lion system preferences).

  If you can make a copy to the front of the printer to scan works.  If you can't, it is broken.  Its a bit easy than this.

  Did you download this: http://support.apple.com/kb/DL907

  Download it, restart, then delete and add the printer in Sys Prefs.

• D110B what all In One not Scan to computer

  Hello - when I try to scan to my computer I get an error message that says: "Error Scan - scan try PC" then I tried to scan my PC using Windows Fax and Scan and the error message says "no scanner detected." I got an error message that the there is a problem with the driver so I tried to download the driver software and it tells me that the file is not found. I contacted Dell and HP and no one can solve the problem. Hope you will be able to help

  Hi Mike, I used the work around and it worked very well.  Thanks a lot for your help and your time.

• HP OfficeJet J5780 all-in-One not Scan under Vista 64-bit

  I have brand new HP Pavillion Dual Core processor and 6 concerts computer memory, so I know that my computer is OK.

  I have a computer set up to Dual Boot Windows Vista Home Premium 64 Bit & Ubuntu Linux.

  Under Linux, the printer will print & scan (both)

  In Vista, it prints only

  My wife has Windows XP on his computer & it prints & Scans

  We come to the rear USB cable & before printing on computers.

  I have downloaded the latest drivers & critical updates & installed Vista without result.

  It will not even scan directly from the printer.

  On the printer, it says:

  No scan option, don't refer to the device Documentation. ???

   

  I know the printer is about 2 to 3 years, but it still works except scan!

   

  Please help, thanks in advance

  It is fixed after reading the HP Help Pages

  To scan in Vista... You MUST do it in paint or Windows Photo Gallery.

  Hope this helps someone

• HP Laserjet Pro CM1415 cold not scan after upgrade to 8.1 windows

  I upgraded Windows 8 to 8.1, and since that time, my laptop can't connect with my scanner.  I tried printing HP and doctor Scan, but when I downloaded the latest driver, he asked me if I wanted to remove my current driver is not to install a new driver.  How can I get my scanner to work?  It prints OK.

  Nevermind, I just tried the other installation option, which was to "connect another HP device.  Quick install another HP device using software already loaded on this computer. "What does install the new printer driver and my printer can scan now.  Now I go back and delete the old driver.

• My Deskjet F380 printer will not scan after upgrade from XP to Windows 7 32 bit

  I have a HP printer Deskjet F380 (S) NC 73 NGZ14S which worked perfectly on Windows XP. Island re install software without disk original and well as the printer and copier are working the scanner is not. I have downloaded and run the Wizaedand that had this message "Full HP software is already installed, but the basic functionality pilots seem to be missing or configured incorrectly. Assistant and then went to "drivers for your printer are disabled click next to allow them to" clicked Next, and he returned to the previous message again. I have not installed the software on. Windows 7 but I don't know that my original HP software disk has not been used. Now must I UN install Windows 7 and re install from the HP website. I got another message in short while the HP site it says driver required WIA trawling. I'm not very experienced on the computer and would like your help thanks Mimosa

  Yes, I would uninstall the driver and software and then download the driver for Windows 7 and install it.

  Here are some instructions for uninstalling: uninstalling the printer software.

  You can download the driver here: Driver and software downloads.

• Could not open after upgrade to Yosemite After Effects

  I recently upgraded my macbook pro to yosemite and after effects upgrade now has a circle with a line through it and not let me open. I get the error that I can't use this version of the application with this version of os x. Any help would be greatly appreciated because I see it should work fine.

  I have Adobe After Effects CS6 11.0 and spin it on a macbook pro late 2011 with i7 and 8 GB of ram.

  Install the After Effects CS6 (11.0.4) updated:

  http://Adobe.LY/DVA_updates

• HP officejet Pro 8500 909: HP Officejet Pro 8500 909 has not scan after downloading Windows 10

  About 6 weeks ago, I downloaded Windows 10.  Today, I tried to analyze something and received the message "no Scan Options".  So I tried to go to the Hp Solution Center and who do not respond. When I was on Windows 7, I have had no problem scanning or with the HP Solution Center.

  Hello

  You will probably need to reinstall the HP software after an upgrade of the operating system.

  Please follow the steps for exactly the problem and check for the difference:

  http://support.HP.com/us-en/product/HP-OfficeJet-Pro-8500-all-in-one-printer-series---A9/3752454/model/3752455/document/c04714314/

  Section ' can not analyze after upgrade to Windows 10 "should apply, or the"HP solutions Center can not run"or 'Scan is busy or in use' error with a connected printer"if it's the exact specified error when you try to open the HP solution... Center.

  If you need to uninstall the HP software, uninstall it by running the following remove utility Uninstall_L4:

  http://ftp.HP.com/pub/softlib/software12/COL31044/MP-77037-4/OJP8500vA909_Scrubber_13.exe

  Kind regards

  Shlomi

• Second monitor is not detected after upgrade to Windows 10

  After you have installed Windows 10 upgrade Windows 7, my second monitor is no longer functional. The computer is an HP Touch Smart 610-1065qd. I connect on the second monitor through a USB 2.0 Port Replicator 2005pr HP. The Replicator appears as a drive when you look at this PC and an arbitrator in him like HP USB DOCK, as it did in Windows 7. The Replicator seems to work, I can't access the SSD on the device and use a wireless mouse. The receiver is connected to the port replicator. The second monitor, also connected to the Replicator, as it was before the upgrade. Now the system is unable to detect this monitor. The MANAGER of peripheral DEVICES, MONITORS, indicates there is a monitor Active, listed as "PnP monitor" generic Device Manager displays a second monitor as a hidden device. Identified as a "generic PnP monitor' and the State of the device is"currently, this hardware device is not connected to the computer. (Code 45) ». In Windows 7, I don't remember the second monitor listing. USB and the DISPLAY NETWORK DEVICES, the entry is USB PORTS port REPLICATOR 2.0 HP 2005pr. Under GRAPHICS cards, there are two lists. The first is an adapter named "AMD Mobility Radeon HD 5570". This corresponds to my video card. The second adapter named "glance speed Boost. I believe that Ancestry.com can installed this. "This device is working properly" is the condition for both cards. I manually checked new drivers for all components. There is no effect. Then, I went to HP and downloaded the most recent Setup to monitor. I then tried to load the drivers and monitoring software. I also loaded the screen in compatibility mode, then in compatibility mode for Windows XP SP3, then compatibility for Windows 7 and finely mode as a regulator. As a result, I tried the same process with the original disc. After each test, I rebooted the system. Still unable to detect the second monitor, nothing in Device Manager and unable to detect a new monitor on screen. I attempt to change the Projection. He also, had no effect on the display. Then, I deleted graphics cards. First of all, the adapter "AMD Mobility Radeon HD 5570", which corresponds to my video card. Second, the "Speed Boost glance. This also, don't give not any what on second monitor display. Even if it is visible only when show it hidden devices is checked. Any suggestions will be appreciated.

  I finely found a fix for the problem to my question; Second monitor, not detected after upgrade to Windows 10. Not the one I was hoping. It turns out that the fault was with the HP 2005pr USB 2.0 Port Replicator. It seems that the driver may be at fault. After more than a month of waiting, I decided to replace the duplicator. I decided to buy a Port adapter to replace the duplicator. What is much less expensive experiment and see if it was infecting the duplicator. It turned out that my second monitor is back and healthy. I decided to continue to use the port adapter and buy a USB Hub to replace this part of the duplicator. I no longer use the HD Audio output, after replacing the old speakers with Bose USB speakers some time ago. I thank everyone for help.

• Projector does not work after upgrade from Sierra

  My projector does not work after upgrade to Sierra. Or search in Outlook (I use outlook for Mac due to having MS 365 for labour) or the search function in the finder. I use this all the time and need this feature back. I tried to reindex spotlight and nothing. Anyone has any ideas.

  Try to rebuild Spotlight rebuild the Spotlight to your Mac - Apple Support index

• Apple Software Update will NOT work after upgrading to Windows 7

  Apple Software Update will NOT work after upgrading to Windows 7

  flyboy340 wrote:

  Apple Software Update will NOT work after upgrading to Windows 7

  More information is needed.

  Which machine you use, OS X are you running?

  Windows 7 running in BootCamp?

  The OS X app store is not present at all?

  AppStore is present but the update tab does not?