VCA Mode Question Xeon X56xx series and series X55xx

Similar Questions

• Precision 690 MY171 rev A00 mobo - hearts Xeon 5300 series

  Hello

  I know that this subject has been discussed in the past, but I am having a hard time finding an answer for my exact situation.  My Dell Precision 690 runs the rev MY171 A00 motherboard on rev A08 bios.  It currently has a single processor dual core Xeon 5150.  I want to upgrade to dual quad core Xeon 5300 series processor.  I've seen youtube videos and discussion with rev A02 MY171 boards that run the 5300 series, but nothing to confirm if the version A00 will run them.

  The rev A00 motherboard BIOS A08 MY171 will work two Xeon 5300 series quad core?

  Thanks in advance for the help!

  Today, I received my processor Xeon X 5355 to four hearts by post and installed in on my MY171 Rev00 on bios A08.  No problem during the performance of the processor.  I took out the battery from the motherboard for 2 minutes before relocation and commissioning for the first time.  BIOS immediately recognized the processor.

  I'm running window 10 and initially he saw only 2 carrots.  I went into MSCONFIG and made some changes on the STARTUP, the Advanced Options tab, you should uncheck 'Number of processors' and restart.  After that, the OS will see all 4 cores.

  I intend to run identical to the second X 5355 processor, but am waiting to get a second heat sink before a fall.

  Hope this helps others seek to upgrade the 690.  The two processors cost me a total of $20 on ebay.  Also got 16 GB RAM DDR2 PC5300 (8X2Go) for this computer for $10.  Computer will work great for $30 worth of improvements.  I still feel like they need SSD to run faster.

• VCA serious question in a cluster after adding servers active DRS blades M630 Dell

  Hi guys,.

  I hope that you will be able to help me with this strange question that I feel right now.

  A couple of details first on our environment:

  • vCenter 5.0 U3
  • ESXi 5.0.0 - 2509828
  • 6 guests active DRS cluster
  • 4 hosts are Dell M620, E5-26XX v2 processor blades
  • 2 hosts are blades M630 Dell with processors of E5-26XX v2
  • VCA mode is currently set at "Westmere".
  • All ESXi hosts are fully patched using AUVS

  Before adding the new M630 blades to the cluster it any of the issues with the DRS or VCA, outside the constraints of resources, and the 4 blades M620 we are able to correctly migrate the virtual machines back.

  I could add the M630 blades to the cluster without problem and without errors or warnings have been issued. A week or so later, I noticed more deviations of DRS desired on the cluster. More inspection I noticed that quite a large number of virtual machines showed N/A beside VCA mode and I was not able to migrate them to any host on the cluster.

  Thinking it could be a bug of sorts, I turned off all the virtual machines in the cluster and run a script that resets the CPUID at default. In addition, as a measure of precaution, I restarted the vCenter server and ensures that the database has been effective. The hosts are synchronized time with an NTP source and fits perfectly on both hosts.

  After feeding all the VMS, I rebooted the M630 servers and inspected the BIOS settings to ensure that virtualization and NX/XD is enabled. With all virtual machines powered off, I was able to change the levels of the VCA to any available without warnings setting.

  When everything has been turned back on I noticed a strange behavior in the cluster.

  Virtual machines that are running on M620 blades show the right level of CVS and I am able to migrate them to all servers in the cluster. Once that they migrate to the blades M630, VCA state change s/o and I am unable to migrate anywhere, not even the other M630 blade in the cluster.

  The error that I am shown during the verification step is:

  The operation is not allowed in the current state of the connection to the host. Host CPU is not compatible with the requirements of the virtual machine to cpuid level 0 x 1 host bit ' ecx' register: 0000:0010:1001:1000:0010:0010:0000:0011 required: x 110: x01x:11 x 1: 1xx0:xx11:xx1x:xxxx:xx11 inconsistency detected for these characteristics: * General incompatibilities; see section 1993 of possible solutions.

  Dig deeper in my investigation, I came across this KB: 1034926[1]

  I checked the M620 user guides and the M630 and parameters mentioned in the KB should be enabled by default. Unfortunately, I have no way to check the BIOS settings because I can not all M630 blades enter into maintenance mode without turning off the virtual machines running on them and another maintenance window one day after previous, we're going to be deprecated. In addition, the error is not the same as that of the KB and my goal is to collect as much information before entering another window of maintenance requiring downtime.

  I hope that you will be able to provide any new perspectives or opening my eyes to things that I may have missed.

  Thanks in advance.

  The processor in this system is a v3 E5-2660, not an E5-26xx v2.  ESXi 5.0 doesn't know how to use the features of this processor FlexMigration.  I think that the first version of ESXi to support this processor is ESXi 5.1U2.

  Unfortunately, I do not see a workaround for ESXi 5.0 solution.

• VCA Mode change

  Hello
  I'm downgrading to Westmere EVC mode to conform to the old generation of host we add to the cluster.

  To do this, I currently have two clusters created, in production and two hosts using sandybridge.

  the second group has a central server inside and westmere generation.

  I am aware of the procedure found here:VMware KB: VCA allowing on a cluster when vCenter Server is running in a virtual machine

  My question is, rather than quick vMotioning of all hosts another machines.  is it possible to close all virtual machines on a host, set mode now, disconnect the host, move it to the cluster Westmere allow it and then put on all virtual machines?

  I know that I'll still have to disconnect and reconnect my vcenter server, but I would like to avoid having a large amount of machines to vmotion if I can find some downtime to stop all.  and make them move with the host.

  This idea is possible?

  So if I understand what you really want is the future VMs with the host computer, then when you add the host to the new cluster and power them they will run under the new EVC Mode but you essentially in bulk installs what you wanted?

  If so, I did what you describe a bunch of times before (especially during migration between vCenters and want to go to the host and all virtual machines), what I would recommend however keeps the VMs powered on. Disconnect the host and then remove the vcenter. Once removed from the cluster and vCenter connect through thick client and put all virtual machines. Then add it to vCenter, in the cluster you want to and feed the VMS and you would be actually resigned these VMs in bulk.

  Conversely, you can turn off the virtual machines and keep track of those you want to migrate, put the host in maintenance mode and move it to the cluster that you want and then get out of maintenance mode, cold migrates virtual machines and then turn on. I think that this option will be a little easier.

  However, to disconnect a host and removing vcenter will make virtual machines with it, that looks like what you want to do...

• VCA mode

  I try to enable CVS mode on a cluster, but get the message "host is not allowed in the compatibility mode of the current cluster Enhanced vMotion.". Under voltage or suspension of the virtual machines on the host can use CPU features hidden by fashion. ».

  The Group had initially 2 servers Dell PowerEdge R810 with dual cpu Intel Xeon E7540. I am trying to add 2 older servers Dell PowerEdge R900 with quad cpu Intel Xeon E7320. I'm guessing it wont let me enable it because virtual machines under tension using the more recent servers (R810) and their cpu. My guess is correct? I need to power all of my virtual machine to enable CVS or y at - it another way to activate?

  Hello

  Yes your proposal was correct. You can disable all your virtual machines to the VCA mode.

  More information about the activation of the CVS: VMware KB: VCA allowing on a cluster when vCenter runs in a virtual machine

  Kind regards

  Julien

• VCA mode in settings of the cluster

  I was wondering what an experience everyone was with the VCA mode settings.  Usually allow you it?  What mode for processors Intel you choose usually?

  the only time you need to activate the VCA is when you have vMotion compatibility issues.  And when allowing it, CVS will choose what mode is the best

• I have a MacBook Pro late 2015, every time I have out of mode 'sleep' it is frozen and I turn it works.  Anyone know why this is happening?

  I have a MacBook Pro late 2015, every time I have out of mode 'sleep' it is frozen and I turn it works.  Anyone know why this is happening?

  Contact Apple for support and service

• I forgot my security question answer Apple ID and my recovery email address has since been deleted and disabled. How to get answers to security questions and or change my email recovery?

  I forgot my security question answer Apple ID and my recovery email address has since been deleted and disabled. How to get answers to security questions and or change my email recovery?

  Go to https://getsupport.apple.com . Click on "see all of the products and services ', then 'More', then 'Apple ID', then 'other Apple ID subjects' then 'security issues forgotten Apple ID". If you have problems with this test of this form: https://www.apple.com/emea/support/itunes/contact.html

• I'm having a holiday in Nha Trang, Viet Nam and my stolen obtained iphone6 10:00-22:30 last night, I activated lost mode which is still pending and said the local police. What should I do?

  I'm having a holiday in Nha Trang, Viet Nam and my iphone6 who was in my bag got stolen 10:00-22:30 last night while returning to the hotel, I activated lost mode which is still pending and said the local police. find my iPhone is in offline mode. What should I do? I read online that if I erase all my data can find that my iphone will be more capable. I also read online that the stolen iphone can be replaced? What should I do? I can't fnd an e-mail to contact apple Australia I did purchase in Sydney Australia.

  Please help me.

  There is nothing for you to do.

  What to do if your iDevice is lost or stolen

  iPhone, iPod Touch and iPad

  If enable you find my phone before it was lost or stolen, you can follow only if it is connected to the Internet by Wi - Fi or cellular. What you can't do, is follow your device using a serial number or other identification number. You can't wait for Apple or anyone else to find your device for you. You can't recover your loss unless you make your device for the loss. It is not covered by your warranty.

  If your iPhone, iPod, iPod Touch, or iPad is lost or stolen, what do you do? There are things you should have done in advance - until you have lost it or it has been stolen - and things to do after the fact. Here are a few suggestions:

  This link, Re: help! I misplaced / lost my iPhone 5 today morning at delta Chelsea hotel downtown one I am not able to follow. Please help!, has some good advice about your options when your iDevice is lost or stolen.

  1. declaration of a lost or stolen Apple product

  2 find my lost iPod Touch

  3. AT & t. Sprint and Verizon can block phones stolen/tablets

  4. What-To-Do-When-Iphone-Is-Stolen

  5. use ICloud Mode lost

  6. what to do if your iOS device is lost or stolen

  7 6 ways to track and recover your lost/stolen iPhone

  8. find my iPhone

  9 report Stolen iPad | Stolen lost found online

  It pays to be proactive in following the advice on the use of find my phone before you lose your device:

  1. find my iPhone

  2 set up your iDevice oniCloud

  3. OS X Lion/Mountain Lion - in regard to my Mac

  4 the free configuration find your iPhone (even on unsupporteddevices)

• Sansa e280 is not usb mode in the menu settings and is not recognized by pc

  My sansa e280 is recognized by my pc where it was originally regestered, but is not recognized by another identical pc. It also has no usb mode in the settings menu, so I couldn't use the suggested by forum solution.

  Thank you very much! I understand it on my own through the main page of Sansa.com. Now, after the last firmware download it has 3 settings/USB modes: detect the DPW, msc and auto. Still no problem on my PC. The another, unfortunately, is 5000 miles away. Hope, it will work here, too. Thanks again.

• I rebooted my machine yesterday and now when it comes to the screen with the scroll bar it restarts in loop. Impossible to enter Safe Mode (arrives at crcdisk.sys and while it recharges) or normal startup mode.

  I restarted my machine yesterday and now when it comes to the screen with scrolling bar (think Night Rider), it restarts in loop.  Impossible to enter Safe Mode (arrives at crcdisk.sys and while it recharges) or normal startup mode.  Startup Repair is unable to repair.  She argues that the onus of a BadPatch.

  Startup Repair shows the following:

  Problem event name: StartupRepairV2
  Signature of the problem 01: external Media
  Signature of the problem 02: 6.0.6000.16386.6.0.6001.18000
  03:6 problem signature
  Signature of the 04:262148 problem
  Signature of the problem 05: BadPatch
  Signature of the 06 problem: BadPatch
  Signature of the problem 07:0
  Signature of issue 08: 1
  Signature of the problem 09: SystemRestore
  Signature of the problem 10:0
  OS version: 6.0.6000.2.0.0.256.1
  Locale ID: 1033

  Hello

  I hope you made redundant data backups as I suspect that the drive has failed. If a PC, you must
  remove all power and remove and reinstall all the cables (at both ends where possible), memory and cards. Do
  not tighten, effectively remove and replace them with care.

  Click here for the manufacturer of your hard drive and launch their diagnosis on your drive.

  By manufacturer diagnostic utilities
  http://www.techsupportforum.com/hardware-support/hard-drive-support/302602-hard-drive-diagnostic-utilities.html
  SpeedFan
  http://www.almico.com/sfdownload.php

  HD Tune
  http://www.hdtune.com/

  ----------------------------------------------

  If necessary:

  You can try an In-Place Upgrade (hopefully save programs and data) or a repair installation (if all goes well
  saves the data, and you need to reinstall the programs). Be sure to do a good backup or three.

  You can use another DVD that are not protected but you will need to copy you have the product key.

  On-site upgrade
  http://vistasupport.MVPs.org/repair_a_vista_installation_using_the_upgrade_option_of_the_vista_dvd.htm

  If nothing works, you can make a repair facility that must save the data but you will need to
  Reinstall the programs. This also requires correct Vista disks especially for OEM versions. You will be
  need to know your product Code.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  How to perform a repair for Vista Installation
  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

  No new chances.
  Rob - bicycle - Mark Twain said it is good.

• Question about Powerconnect M6220 and out-of-band/management 8024-K connection

  I'm sorry if this question belongs to another section, but with regard to the functionality of these switches I thought I would start here.

  My question is, the M6220 and 8024-K out-of-band connection are going through the connections on Board (for example port 18 for example) or through connection of the M1000e CMC?

  The reason for this question. We recently vlaned our network and CMC modules are VLAN 8 (10.100.8.0 255.255.248.0) and management of our switches is supposed to be on the VLAN 1 (10.100.1.0 255.255.255.0). I can't ping on the affected IPS (IE 10.100.1.15), but our CMC modules are fully accessible (IE10.100.9.120). Our blades are fully accessible and can access all the VLANS on them (they are the ESX host).

  Finally, I'm sorry if all necessary information has been provided, I'm not so much a networking guru.

  Thoughts?

  Thanks for your help

  The OOB interface is connected to the chassis management controller by the median plane of the chassis. Traffic on this

  port is separated from network traffic operating on the switch ports and cannot be lit or routed to the operational network.

• Burrito of flash builder design mode is a white screen and does not not all components

  Hey guys, for some reason none of my components appear any, when I go to design mode in flash builder burrito, and the screen is white. When I run the app, it works very well and seems very well my only problem is that I don't understand what is happening in "Design Mode". Someone has a similar problem to this, also, I don't get any errors about not being not able to load the design view just a pop-up that says that it takes a while to load and to continue or not. The only time I see a component is when I go to the source and highlight a component then go into design mode, then u see a blue outline of the component. You can see in my screenshot above. Any help would be great, thanks in advance.

  Thanks again,

  Brian

  Design mode does not work if you include qnx libraries in the path of the libraries due to a bug in FB, there is a flag to uncheck (qnx libraries) in the project to BBT properties

• We can add a button to the BP to approve Budget so that it can read all the charges in question cost journal line and auto fill on the grid.

  Hi all

  We can add a button to the BP to approve Budget so that it can read all the charges in question cost journal line and auto fill on the grid.

  Let's say I have a cost with 5 code cost journal

  Code 1 price

  2 cost code

  Code 3 cost

  Code 4 cost

  Code 5 cost

  BP budget approval, after that I click on New, can I add a button to the tab the line items so that when I click on this button, it reads all codes of cost in the cost journal and auto fill on the grid?

  You can create a new 'model' BP for this purpose. Line item type. Then add a line manually with a cost on each code. Then you can use the copy in your BP BA record consolidate the function to copy the line items to the new folder of BP (including all cost codes) into your folder of BA. That is to set up a model record once with all cost codes and then copy consolidate billing it to all lines new record of BA. would this work?

• Questions about the terms and conditions

  Dear team of Adobe Stock,

  I am considering a subscription for an e-commerce site that I am developing. I have a few questions about the terms and conditions:

  3.5 social media use. You can view or download an unmodified version of the book on the Social media Site if (A) you include a notice of copyright in the work itself (© author name - stock.adobe.com) and (B) the terms of use governing the Social media Site do not include any provision that would grant exclusive rights or the ownership of those works or alterations to anyone. "Social Media Site" means a website or application that puts the main emphasis on facilitating social interaction between its users and allowing users to share content in such social interaction

  What I have to insert in each post on social media on behalf of the author? Generally, this information is displayed only for free images. What I have to insert this information even if I signed up for a plan?

  Thank you

  Hello

  Please see the link below for help:

  http://wwwimages.Adobe.com/content/dam/ACOM/en/legal/servicetou/Adobe-stock-additional-ter ms_20160119.pdf