vCAC 6.0.1 new end point

Similar Questions

• visa usb communication in bulk - several end points

  Hi all

  I'll put up a spectrometer optics USB2000 + ocean and want to use visa instead of the dll that I had with the spectrometer (I had a lot of stability problems, moreover, this is not supported by the ocean optics and I won't have to pay for the new version).  I have documentation for the spectrometer and were able to set the integration time and receive ghosts as quickly that the dll has been able to.  But I was not able to read the information of calibration of the spectrometer.  All controls use the transfer block, so I use visa read and write to send/receive.  I think it's the difference between the spectral data and calibration data, that the data comes from different points of termination.   The spectrometer has 4 endpoint addresses (3-PC = IN, 1 PC = OUTSIDE).  The spectral data returns to the first endpoint and the calibration data is on 3rd in.

  Is there a setting I need to change to read from a different end point?  They are all in bulk type according to the documentation.  Any suggestion would be appreciated.

  Thank you!

  Hey gharris,.

  It seems that there is a parameter, you can change by a property node that will change reading from what endpoint. If you use a text-based program, the property, you need to change is VI_ATTR_USB_BULK_IN_PIPE. If you are using LabVIEW, follow these steps:

  First of all, to ask a VISA property on your block diagram node (really any node property works). Then, right-click on the property node and select Select class-> VISA-> / o Session-> USB Raw. This step can be found in attached below EndpointSS1.png and change the property node to a node property USB Raw. Thirdly, left-click on the property and select settings USB-> pipe in bulk. This step can be found in EndpointSS2.png, attached below. It is the property that defines at what endpoint to read from. To change the value of the present, right-click on the property node and select change all to write, which will allow you to connect to an endpoint value.

• "There is no end point for the end point mapper.

  Summary of the issue
  Other issues of Windows Live family safety

  What version of Windows Live Family Safety do you use?
  Version 2011 (15.4.3538.513)
  Choose your operating system version:
  Windows 7

  Additional details
  Whenever I have try and configure the accounts of FS, I get an error that says: "there is no end point to the end point mapper.  I tried to uninstall the parental control and re - install the latest version several times and I get the same error.  I created several new accounts and tried to tie but still the same error.

  Any help?

  I had the same problem and the error you mentioned above... Has been frustrating me. After working through the questions Tech above, I discovered that it was related to basic and Windows Firewall filtering engine.

  Check if your Windows Firewall is working properly, and if you can make changes. If you get an error code when you try to change your firewall settings, which could be what it is.

  I followed this to correct the BFE and Windows Firewall it retries then parental control and he went through with NO PROBLEMS of...

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-Security/Windows-Firewall-cant-change-some-of-your-settings/514d78fb-39e9-47b1-B561-bc49cbdad904

  Hope this works for you as well...

• question on pdc's end point mapper

  I have a problem with the domain controller or when you try to replicate to the new Member serevr which is a backup domain controller it fails and says end point mapper isue? any help would be greatly appreciated?

  Thank you

  j

  Hello J,

  Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for Windows Server on TechNet. Please ask your question in the Forums in TechNet Windows Server.

• No sound - "either Windows Audio and Windows Audio services end Point Builder is not running."

  original title: no sound - Fix he said "either Windows Audio and Windows Audio services end Point Builder is not running."  What should do?

  When I ran Microsoft Fix it for audio, it says that it is unable to solve the problem.  The message was "two windows audio and Windows Audio end Point generator services must run for audio works correctly." At least one of these services is not running. "What should I do now?

  Content in double wire-
  "When I try to use anything related audioi on my computer (volume of the speaker, open iTunes, watch a video), a box appears that reads,"c\Windows\System32\MMDevApi.dll is not designed to run on Windows or it contains an error. " Try to install the program by using the original installation media or contact your system administrator or support software provider. "The mystery is that I have nothing to my computer to ask for that. I have not installed anything new or change the settings. It just started happening. Any advice? »

  Hello

  1. are you able to hear the sound after the error message?

  2. you have an an external sound card or internal, installed on the computer?

  Method 1:

  I suggest you to follow the steps and check.

  (a) click Start

  (b) type services.msc in the search box, and then press enter.

  (c) scroll down to Windows Audio and Windows Audio endpoint builder of Point

  (d) both should be started and set to automatic if one or both are arrested.

  (e) click the name to select it.

  (f) click on restart the service at the top left.

  (g) repeat for both if necessary. If some are not set to automatic, and then double-click the name and on the drop-down list to set the startup type to automatic and apply and ok your way out.

  Method 2:

  I suggest you to run the automated FIXIT from the link below. You can also follow the other steps and check.

  Tips for solving common audio problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-sound-problems

  Method 3:

  If you have a sound card, I suggest you uninstall the audio driver from the Device Manager and and then install the latest audio driver version from the sound card manufacturer's website.

  To uninstall the Device Manager sound, proceed as described in the link below.

  Open the Device Manager

  http://Windows.Microsoft.com/en-us/Windows-Vista/open-Device-Manager

  Find the audio driver in the list, do a right click and Uninstall.

  You can also download the drivers from the link below.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  Method 4:

  If the steps do not help, I also suggest you to run a scan of the System File Checker .

  Click on the link mentioned below for more information about the System File Checker analysis

  http://support.Microsoft.com/kb/929833

  Hope this helps and keep us posted.

• What's new in point 7.2 of Skype?

  What's new in point 7.2 of Skype? I see no difference... yet.

  The main visible difference is that the local time and the balance of credit are now appear again on the main Skype window.

  http://community.Skype.com/T5/Windows-desktop-client/7-0-and-your-feedback-on-the-new-chat-UI/m-p/38...

• Is it possible to get programmatically the end points of a Switch Executive road connected in LabVIEW?

  I am writing an application for plotting of curve for evaluation of ASIC devices and should link all of the pairs of pins possible to do this. I use the main switch to load in the roads, there is a specific ASIC and want to get programmatically the end points of the current road for insertion in the logging system. Is this possible?

  Thank you

  Nick

  It can be an adventure, but you can get there.

  

• How to connect 3 end points to 1 row reserved

  Is it possible to set up a group of MAX lines linking 3 end points to a single line of a matrix card 4 x 128, which was reserved for routing?

  I need to have all four rows defined as reserved for routing so I can set up all my other road groups by specifying endpoints.

  Thank you
  Jason

  Hi Jason,

  I guess you don't use OR-Switch 2.3.  To my knowledge, NI Switch Executive came out only with the following versions: 2.0, 2.0.1, 2.1, 2.1.1 3.0.

  The option you listed is not your only option, but this is the option I recommend for older versions of NI Switch Executive.  Don't forget that you can use groups of road to store the line separate to the Poles, while only a call connection is required.

  One extra option that you have is to use two NI Switch Executive devices virtual.  A virtual device a module the PXI-2532 lines reserved for routing and the other virtual device is not.  Whenever you want to connect more than one column on the same line, you may close the session to the 'reserved for routing' virtual device and log on to the other virtual device (where you connect several end of column points to the same line).  Note that you can not sessions open to two virtual devices at the same time because they try to share the same hardware.

  Upgrades to NI Switch Executive 3.0 a possibility?  There are two additional functions, you enjoy:

  • Intuitive graphical Configuration utility
  1. Point-and-click graphical configuration environment - allows rapid development of switching systems
  2. Change channel aliases in place
  3. Create complex routing groups by clicking matrix points one at a time
  • Import/export of Microsoft Excel
  1. Easily export the NI Switch Executive configuration in Microsoft Excel environment
  2. Increase the number of channels by simple text manipulation
  3. Easily import files newly edited in NI Switch Executive

  It would be great if the upgrade have been an option.  Let me know if you have any other questions!

  Chad Erickson

  Switch Product Support Engineer

  NOR - USA

• Error during the initial install: there is no end point for more available from the endpoint mapper.

  Summary of the issue
  Other issues of Windows Live family safety

  What version of Windows Live Family Safety do you use?
  Version 2011 (15.4.3538.513)
  Choose your operating system version:
  Windows 7

  Additional details
  While you select "Accounts of Windows I want to monitor on this computer" it shows the loading for a long time then popus symbol with:

  Windows Live Family Saftey modal window popup:

  "There is no end point for more available from the endpoint mapper."

  800706 9 error code

  Any ideas?

  I had the same problem and the error you mentioned above... Has been frustrating me. After much research I found out she was related to the basic and Windows Firewall filtering engine.

  Check if your Windows Firewall is working properly, and if you can make changes. If you get an error code when you try to change your firewall settings, which could be what it is.

  I followed this to correct the BFE and Windows Firewall it retries then parental control and he went through with NO PROBLEMS of...

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-Security/Windows-Firewall-cant-change-some-of-your-settings/514d78fb-39e9-47b1-B561-bc49cbdad904

  Hope this works for you as well...

• Vista gives the message "there is no more available end point" and does not allow me to share a folder on an external drive. Can you help me?

  Vista gives the message "there is no more available end point" and does not allow me to share a folder on an external drive.  Can you help me?

  Hello

  Thanks for posting in the Microsoft Community.

  I don't know it must be frustrating!

  Let us try these steps and see if that fixes the problem:

  (a) press Windows + R keys to open search Run

  (b) type regedit , and then click ok

  go to HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\BFE

  c) on the right, click it, click permissions

  (d) click on ADD and type everyone and click ok

  (e) now click on all

  (f) below, you have permissions for users, select full control and click ok

  g keys) press Windows + R to open Run Search

  (h) type services.msc , and then click ok

  (i) double-click base filtering engine service.

  (j) Make sure that the service status is started and the startup type is automatic

  (k) the procedure for the windows firewall service

  (l) click on apply and Ok.

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information:

  Back up the registry:

  http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry

  Hope the helps of information. We know if you need help. We will be happy to help you.

• RPC end point Mapper is missing from my computer

  How to re-install RPC end point mapper?

  Nancy

  Press the Windows key and the R key

  in the Find box type services.msc

  In the list of services find the RPC end point mapper

  It must be set to automatic and must be started if it is not started

  Start it

  If it is not set to automatic

  Highlight the RPC end Point Mapper and right click, select Properties

  Change the Startup Type to automatic

  Click on apply and OK

• Create a new restore point shortcut

  Would like to know where to find the way to have a Windows 7 desktop shortcut to create a new restore point.

  Thank you!

  Set the path of the shortcut:

  %SystemRoot%\System32\SystemPropertiesProtection.exe

  Boulder computer Maven
  Most Microsoft Valuable Professional

• An error occurred when trying to share Share_OD. There is no end point for more available from the endpoint mapper.

  I wanted a user to add a group named "OD" the client Desktop Machine and another thing is that OU is created named OD. But an error that "an error has occurred all trying to share Share_OD. There is no end point for most the endpoint mapper. »

  Hi Laurent,.

  This request is outside the scope of this forum. I suggest you to send this request in the Microsoft TechNet forum for better support.

  https://social.technet.Microsoft.com/forums/en-us/home

• An error occurred when trying to share < folder name >. There is no end point for more available from the endpoint mapper. The shared resource was not created at this time

  Original title: sharing folder error

  How to solve this error message when I am trying to share a folder: "an error has occurred when trying to share . There is no end point for more available from the endpoint mapper. The shared resource was not created at this time. »

  Hello

  Were there any changes made on the computer before the show?

  I suggest to see the link and try to run the Troubleshooter:

  Share files with anyone

  http://Windows.Microsoft.com/en-us/Windows7/share-files-with-someone

  See also:

  File sharing essentials

  http://Windows.Microsoft.com/en-us/Windows7/file-sharing-essentials

• There is no end point for more available from the endpoint mapper

  My wife is currently running Windows 7 Home Premium.  Trying to create a share gives the following error: "year error occurred while trying to share share name."  There is no end point for most the endpoint mapper. "It's a peer-to-peer network, the other computers running Windows 7 Professional.  No service is disabled or failing.  Any ideas? »

  This could be caused by the procedure call Locator service remote does not. See http://answers.microsoft.com/en-us/windows/forum/windows_7-performance/error-1753-there-are-no-more-endpoints-available/de6f9381-fea6-4bee-b646-b06b81f75d19 for more information.

  I hope this helps.