Similar Questions

• How to change address e-mail iCloud?

  How to change address e-mail iCloud?

  Welcome to the Apple community.

  Unfortunately, you cannot change your iCloud email address.

  However, you can create an email alias to use parallel to it, you can do so at iCloud.com > Mail > settings (icon gear at the bottom of the page) > Preferences > accounts

• VCS called Ip address routing

  Hello

  I have a question about my VCS control configuration.

  In my scenario, I have control of Vcs and Vcs Express Way.

  I implemented the rule in VCS control:

  .. .the problem: same end point not working with a record keeper and only receive an IP calls. The ip call go all in internet (from the Expressway)

  -----------------------------------------------------------------------------

  Source: AllZones

  Mode: All IP addresses

  On correspondence: continue

  Target: Path (VCS Express Way area)

  ------------------------------------------------------------------------------

  If I call a point of endpoints in the Internet, everything works fine, but if I have to call via ip address, endpoint Internel network (with ip address 10.x.x.x), he call go Express Way.

  I want to put in the control of VCS, rules that use the direct dial plan for all internel ip address (which begins 10.*) and use the indirect numbering plan for the call "unknow ip address."

  Thanks for your help

  FCostalunga

  Hi FC,.

  You can solve this problem by creating a subarea on the VCS control where the subzone membership rule contains subnets with the range of the IP intern (s). For subareas containing the IP address ranges, IP addresses that fall within these ranges is considered known to the VCS, and when endpoint composed one of these addresses IP control VCS will try to set up the call to the IP address itself rather than attempt to transmission by proxy, the call through highway.

  To do this, you must also a rule of search "AnyIPAddress" on your VCS control that points to the local area.

  For reference, I recommend you read through the "Component IP" section in the Administrator's guide from the VCS for X 7, which explained further on the subject.

  Out of curiosity, why you prefer calling IP addresses rather than h.323/SIP URI?

  Hope this helps,

  Andreas

• Changed address IP Linsys WRT54GS2

  For some reason any the IP for my WRT54GS2 changed on its own. Instead of the 192.168.1.1 this is something different, so I could not access my router configuration page. I have reset the router and it was not yet the standard 192. etc. Should I be concerned? I was able to know what it is looking for what was the address of the gateway. One thing that I did was unplug the router when I'm using it not (with safety tips). This could be what has changed? Finally, I can change it to the original IP address and if I do what I do with my computer? Any help would be greatly appreciated.

  As long as your Internet connection is working through the router and your network is secure, I think not that there is nothing to worry.

  If you want to access the router configuration page, check the default gateway on the computer that is connected to the router.

  Open Internet Explorer and type the default gateway in the address bar and check if you can access the router configuration page.

• Persistent cat problem after changing address IM regime in CUPS v 11.0.1

  We have a working installation with the cat persisted on external Postgresql DB, with many chat rooms that are in daily use.

  CUCM and CUPS are on version 11.0.1

  To change the IM AD - name address to the email address, in order to facilitate the XMPP Federation (among others).

  The change of address IM is no problem, but after the change of the person is member (or owner/creater) of any permanent plus discussion space.

  I guess it is because of the change of address IM causes a regeneration of JIDs, and none of the news JIDs are present in the external BD. Maybe it's some sort of synchronization could fix that, but I returned immediately to a change of pre snapshot when I noticed the problem. So I don't know if he forge set it's me, if given the time.

  I wanted to just some time to study before I'll try and make the change again.

  Is it possible that I can change my IM addresses and keep all my persistent Chat rooms? Or is my only option to recreate all the my persistent cat?

  Any info/advice is welcome.

  Rune

  I don't think that there is a fix for this, at least not an easy, one, once the service written messages to the DB, that's changing the JID triggers it all the necessary changes in the IM & P server, for inside DB, contacts lists, etc. But which does not extend to external databases.

  What you might try, and I'm not sure it will work, is to go to the tc_rooms table and change the CREATOR_ID to the IADB and new, if it works, you have to try tc_users then tc_messagearchive and tc_messages and if the entry/exit time recording, tc_timelog

  It would be the only way I could think, but that means you would need to change all the old JIDs for new.

  If this does not work, then you will have no option but to recreate the rooms.

  EDIT: Just out there is a bug related to this:

  Persistent chat rooms is not accessible after a change of field of presence
  CSCuv13723

• Change address IP Central UCS

  I need to change the IP of our Server Central of the UCS. Help, please.

  Hi Chuck,

  For Central UCS 1.2, the instructions are below;

  Instructions for UCS C 1.2:

  * To change the IP through the user interface, select the Administration tab > General > Management Interface.

  * If there are saved UCSM connected to UCSC, you must unregister and then reregister them in UCSC. As in "once you save a Cisco UCS Cisco UCS Central domain, you cannot change or change the IP address used by the Cisco's UCS Manager. If you need to modify or change the IP address, make sure to cancel the registration of the Cisco UCS Central area, change the IP address, and then re-register in Cisco UCS Central. »

  * No record UCS Central, all global policies will be defined in local. This will not affect the functionality of your system. However, after signing UCS Central again with the new IP address, you will need to manually set all policies at the global level.

  * There is currently a request for improvement raised to simplify this process.

  Please let me know if you have any questions

  Reference:

  ---------------

  -BugID: CSCus59391http://cdets.cisco.com/apps/dumpcr?&content=summary&format=html&identifier=CSCus59391 >; -Change the IP addresses of the UCS Central

  https://Tools.Cisco.com/bugsearch/bug/CSCus59391/?reffering_site=dumpcr

  -Covering Central UCS memo

  http://www.Cisco.com/c/en/us/TD/docs/unified_computing/UCS/UCS-central/install-upgrade/1-2/b_UCSC_Install_and_Upgrade_Guide_1-2/b_UCSC_Install_and_Upgrade_Guide_1-2_chapter_0111.html

  Hope this helps you. If you have any other questions, let us know.

  Qiese Sa'di

• How to change address on ASA 5520 VPN peer

  Environment:

  7.2 (1) running ASA 5520

  IPSEC VPN L2L established by using wizard.

  Change the IP address of the remote peer. Using ASDM, I can't change the name of the Tunnel Group (which is currently the address peer). I may change the address peer in the IPSec rule, but is that all that is necessary?

  I have to add a new group of tunnel using the new address of peers for the name? If yes how it is related to other objects that are required for a VPN?

  When you create a VPN using the wizard, it creates several objects that are difficult to track when changes are required. Is it better to remove all current VPN objects and create a new configuration using the wizard again?

  Is it's better to make the changes using the CLI? What lines must be changed for peer address when using the commands?

  Thanks in advance for any help!

  I may change the address peer in the IPSec rule, but is that all that is necessary?

  -No, tunnel group name must match the peer address.

  I have to add a new group of tunnel using the new address of peers for the name?

  -Yes.

  Is it's better to make the changes using the CLI?

  -I recommend it, but if you don't know you have no choice.

  Add new tunnel-group with group as new name address peer, same key etc. Add a new address peer settings under rule edit ipsec peer. Then you should be able to remove the old tunnel group. Hope this helps you, been a while since I made this way.

• Cisco vcs 'Phantom' or false attempts at URI dialing

  A customer reported that there are many attempts to appeal to non-registered or 'false' URIs in their control of VCS and VCS Expressway, the consecuence is the saturation of internet bandwidth customer due to the many requests.

  This has been discussed before in these forums.  Take a look at some of the following threads:

  • nuisance-h323-call-sx20
  • Ghost-calls-tandberg e20
  • sourceh323idcisco-incomingcalls
  • VCS-sip-abuse-reported

  Wayne

  --
  Remember the frequency responses and mark your question as answered if appropriate.

• Change address misspelled Microsoft account

  have a Nokia 520 series and I'm not aloud to access my account due to misspelled email address what can I do to avoid a hard reset

  Hello Charles,

  Thanks for posting your question on the Microsoft community.

  Thank you for details on the issue.

  I suggest you to change the e-mail address associated with your Microsoft account and review.
  Refer to this article:
  How to change the e-mail address associated with your Microsoft account
  http://support.Xbox.com/en-in/my-account/Microsoft-account/change-email-sign-in-for-Microsoft-account

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• How to change address billing from one country to another

  I moved from the United Kingdom to South Africa and my current credit card is linked to my new address here. However I can't update my billing information, because the field where I enter my zip code does not accept the format of my current zip code (which is different from my old)

  The country of your payment address, the country on your Adobe account and the store you purchase of should be the same.

  FAQ: How can I change the country associated with my Adobe ID?

  FAQ: How do I change my credit card information?

  You can contact our support for assistance staff:

  FAQ: How to contact Adobe for support?

• Change address MAC of VM

  
  We have just P2V had a server in a cluster 5.1 ESXi and I should keep the MAC address of origin for licensing reasons. I added the lines below in the .vmx file.

  ethernet0.checkMACAddress = "false".

  ethernet0. AddressType = 'static '.

  ethernet0. Address = 00-24-E8-7A-51-B0

  But when I turn on the virtual machine, I get this error. How can I change the MAC to keep the original MAC from the physical server?

  An error was received from the ESX host turning machine virtual server name.

  Unable to start the virtual machine.

  Power DevicePowerOn module has failed.

  Could not set up "macAddress" for ethernet0.

  Specified is not a valid MAC address.

  '00-24-E8-7A-51-B0' is not a valid Ethernet address.

  Thank you

  Scott

  Try like this:

  ethernet0. Address = 00:24:E8:7 A: 51:B0

• How to change address MAC of Console of Service?

  Our network department wants the MAC addresses to create DHCP reservations for all systems with a fixed IP address.

  We have provided all service consoles virtual MAC addresses on our ESX 3.5 U4 machines. This method works.

  After reinstalled an ESX after a failure of the drive, our MAC service console has changed. I am looking for a way to configure the MAC address of the former esx Server installation.

  Is it possible somehow?

  Edit/etc/sysconfig/network-scripts/ifcfg-vswif0 and restart the network.

  ---

  VMware vExpert 2009

  http://blog.vadmin.ru

• Cannot change address form must be returned to?

  I'm new to creating form in Live cycle.

  I created a form and which works very well but need to change the return address. I changed the e-mail address on the field object tab and saved the form.

  When I distribute even if the sender of the original e-mail address always shows on the entry form.

  Please can anyone suggest where I'm wrong?

  When you distribute a form using LiveCycle Designer file > distribute the form... it asks some preferences for example email etc. However, they cannot be reset if you make changes to the form and run the file > distribute the form later.  The only way I found to change the e-mail address is to edit the PDF file in Adobe Acrobat Pro.  Go to file > Preferences and select the identity category and you can change the e-mail address from there and save your form.

  Hope this helps,

  Paul

• Regarding the change address details account Page

  Hello
  
  In the detail account Page, I'm not able to change the billing address IE documents created by other users. In the account object related information "Addresses", read/change then if the problem is resolved. But don't nt related Information Section dealing with the tabs under the details of the accounts or ideas page him perform the billing address in detail Page also?
  
  Kindly, help with the same
  
  Thank you.

  Billing and shipping information you enter @ top doing the account address list cmdlet (your would have observed) so, technically, I guess he's using the same for storage / extraction I think that yes the access restriction also applied to two places

  -John CRMIT

• update/change address e-mail/user name

  How can I do this?

  HI mebeaudrey

  We also invite you to contact our support team at http://adobe.ly/yxj0t6.