vGPU HA test fails with insufficient resources

Similar Questions

• who can help me with "insufficient resources to meet the level of failover configured for vSphere HA.

  Hello world

  We tried to gif a 14GB of ram and make server complete a booking for her.
  This is a server for the exams and the vendor told us to do.

  I can't any more then 5500MB reservation on it, when I anymore that I get
  "Insufficient resources to meet the level of failover configured for vSphere HA.

  We have:

  2 X 5.1 ESXi hosts
  Each host has
  2 x processors (8 Cores each) with HT active.
  255,75 GB of Ram

  vSphere HA has been activated.
  Admission control policy is enabled and that the ability to failover is 1 host.

  What is the problem here?

  Thank you
  Ernst.

  
  

  Admission control policy is all about to give you the kind of guarantee that if the host failure happens then there will be enough resources to perform the successful failover.

  in simple terms, it comes to reserve the resources of failover.

  I would recommend going through the notion of vSphere HA, reduced control policy the following document.

  https://pubs.VMware.com/vSphere-60/topic/com.VMware.ICbase/PDF/vSphere-ESXi-vCenter-Server-60-availability-Guide.PDF

  From the Page number 22, the details that you need to study is given. Focus especially on part calculations Slot size of it.

  in your case you HA vSphere with number of failure of host to tolerate as admission control strategy defined.

  This means system will calculate CPU and memory slots out of the resources in your cluster, and the total number of units, it will keep some resources like reserved for failover, and others will be available to be used. It all depends on how much failure of hosts that you want to tolerate.

  now in your case, if you try to increase booking one of the virtual machine, which will then affect the number of locations in your environment, and so reserved ability to failover is violated, the system will not let you do what you want to do. As the energy on a virtual machine, or growing booking a powered VM etc..

  If you find that you have enough resources in your cluster and due to some virtual machines with very large cpu or memory reservation, number of places is less than you can still manage the settings some advanced in vSphere HA configuration, but I strongly recommend, try to take the help of someone who has done it before.

  also try to go through other admission control strategies which are explained in the document for more inputs.

• Certification of storage - tests failed with the "VM is in an invalid POWER State for operation"

  The LunReset TargetReset testing and Certification VMware Ready storage has failed with the following error:

  [< Timestamp > TESTHASH] [0] ERROR: cannot run processSetup for configuration: cannot run handleHostVMObj for configuration: RC: 7149 ErrDesc: VM is in an invalid POWER State for operation: ErrMsg: VM is in an invalid POWER State for operation: receiving Exception: com.vmware.qa.staf.common.EOperationFailed Trace: com.vmware.qa.staf.vc.vm.STAFVirtualMachine.checkAllowedCurrentPowerState(STAFVirtualMachine.java:1762) # com.vmware.qa.staf.vc.vm.STAFVirtualMachine.powerOn(STAFVirtualMachine.java:392) # com.vmware.qa.staf.vc.vm.VMSTAFService.handlePowerOn(VMSTAFService.java:4169) # com.vmware.qa.staf.vc.vm.VMSTAFService.acceptRequest(VMSTAFService.java:468) #.

  
  

  [< Timestamp > TESTHASH] [0] ERROR: cannot run processSetup for configuration: cannot run handleHostVMObj for configuration: RC: 7149 ErrDesc: VM is in an invalid POWER State for operation: ErrMsg: VM is in an invalid POWER State for operation: receiving Exception: com.vmware.qa.staf.common.EOperationFailed Trace: com.vmware.qa.staf.vc.vm.STAFVirtualMachine.checkAllowedCurrentPowerState(STAFVirtualMachine.java:1762) # com.vmware.qa.staf.vc.vm.STAFVirtualMachine.powerOn(STAFVirtualMachine.java:392) # com.vmware.qa.staf.vc.vm.VMSTAFService.handlePowerOn(VMSTAFService.java:4169) # com.vmware.qa.staf.vc.vm.VMSTAFService.acceptRequest(VMSTAFService.java:468) #.

  
  

  
  

  What can be done to fix this?

  
  

  TIA
  

  Try turning off all your test vm1 ~ vm16 initially. then run the test.

• H8-1414: boot diagnostic hard drive test fail with "FAILURE ID: 90EF6C-00811-9XPK0K-60RC03.

  I ran diagnostic quick test for my hard drive boot and he responds with the message

  "FAILURE ID: 90EF6C-00811-9XPK0K-60RC03.

  Could someone tell me what the error id code?

  Thank you!

  Thanks to anyone who might help. I bought a new hard drive today and I'm about to install. Best wishes to all!

• NAS NFS Mount/Unmount Test failed with this error - "failed to Test script 300 s to/opt/vmware/VTAF/Certification/Workbench/VTAFShim line 279, line &lt; STDIN &gt; 309 cleaning" it's a matter of workbench?

  Excerpts from run.log

  *****************

  2014-09-10 13:21:51 UTC...

  2014-09-10 13:21:51 UTC [VMSTAF] [0] INFO: VM: [PID 13775] command (perl /iozone - duration.pl d 3600 f - 128 m - r 1024 k t /tmp/iozone.dat 1 > /iozone.2.log 2 > & 1) on 192.168.1.25 is completed.

  2014 09/11 01:36:16 UTC Test script failed to 300 s to/opt/vmware/VTAF/Certification/Workbench/VTAFShim 279, < STDIN > line 309 cleaning.

  2014 09/11 01:36:16 UTC interrupted Test

  One thing noticed here is that there is no logs generated during about 12 hours between the completion of test on one of the GOS and Test Script failed.

  All of the recommendations will help...

  Do not wait more than 2 hours if you think that the test case is stuck. Clean and restart the test.

• Pavilion Memory Test failed., ID 64W662-5066J2-XD7XGK-400V03 failure

  Crash... The BIOS memory test passes, but the HP Diagnostic memory test fails with the ID 64W662-5066J2-XD7XGK-400V03 failure.  Product ID VM298UA #ABA.  Any ideas?

  Hello

  Try the following.

  First, download the Memtest Image file (.) (ISO) on the following link.

  http://www.memtest.org/download/4.20/Memtest86+-4.20.ISO.zip

  It is a zipped file, if you do not have an extraction utility installed, download and install 7-Zip.  Please note that If you have a 64-bit installation, download and install the Installer x 64 64-bit .msi on the link below.

  http://www.7-zip.org/

  Then, right-click on the zipped file, select Extract 7 - Zip, select the files and then click Ok.  Open the newly extracted folder to find the Memtest Image.

  Now, you will need to use an application like ImgBurn to burn the ISO correctly on a blank CD - a guide on the use of ImgBurn to write that an ISO on a disc is here.

  When you created the CD, shut down the laptop.  Tap the escape key when you rewind to enter the Boot Menu.  Insert the Memtest CD.  Select 'Options of Boot' (usually f9), use the arrow keys to select the CD/DVD drive and press ENTER to boot from the disc.

  At least 3-4 passes and see if errors are found.

  Kind regards

  DP - K

• SMART short Self Test Failed - (error code: WHD16-8NR)

  Hi all

  I had my XPS L520X for 4 years and 2 months. I've never had a problem with its operation until last week. Randomly, it restarted and came with the PCI Realtek issue when it restarts.

  To cut a very long story short Fault find it which is going on, I reinstalled the entire operating system, including formatting of the hard drive.

  The problem of the laptop different freeze/crash and reboot with erros while doing normal tasks has not been resolved.

  I have run the Dell support center software and it shows the auto SMART test failed with the following code (error code: WHD16-8NR).

  Event log:

  Dell Support Center log file
  March 17, 2016 16:53:55
  Overall result: failed

  -------------------------------------------------------------------------------------------------------------------------------------------
  ST9750420AS [ATA:0:0\\?\ide#diskst9750420as___0005dem1#4&34e0611c&0&0.0.0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b]}
  -------------------------------------------------------------------------------------------------------------------------------------------

  Seller: Seagate
  Model number: ST9750420AS
  Serial number: 6WS100EG
  Firmware revision: 0005DEM1
  Size: 698,6 GB
  Rotation speed: 7200 RPM
  Cache size: 16 MB
  Temperature: 43 c
  Physical sector size: 4 KB
  Logical sector size: 512 B
  Count of logical sector: 1465149168
  Supported standards: ATA8-ACS, ATA/ATAPI-7, ATA/ATAPI-6, ATA/ATAPI-5
  Specification Version: Rev ATA8-ACS 4

  ----------------------------
  OS - C: [PARTITION:C\\.\C:\]
  ----------------------------

  File system: NTFS
  Volume serial number: 5087-8802
  Volume capacity: 679.00 GB
  Amount of free space: 568,63 GB
  Volume space used: 110,37 GB

  Test of the SMART State

  Test started - 17/03/2016 16:43:57
        
  Finished test:-17/03/2016 16:43:59
  Past

  Test of SMART thresholds

  Test started - 17/03/2016 16:43:59
        
  Finished test:-17/03/2016 16:44:01
  Past

  Targeted reading test

  Test started - 17/03/2016 16:44:01
        
  Finished test:-17/03/2016 16:44:05
  Past

  Try to search randomly

  Test started - 17/03/2016 16:44:05
        
  Finished test:-17/03/2016 16:44:54
  Past

  Funnel Seek Test

  Test started - 17/03/2016 16:44:54
        
  Finished test:-17/03/2016 16:46:14
  Past

  Short what SMART self-test

  Test started - 17/03/2016 16:46:14
        
  Error message:-17/03/2016 16:46:24
  The unit has reported the following State: the previous self-test completed having the read element of the test failed.
  Error message:-17/03/2016 16:46:25
  The first default LBA value is 121243744 and the failure occurred after that the device was working since 8792 hours under tension.
  Finished test:-17/03/2016 16:46:26
        Failed (error code: WHD16-8NR)

  Surface Scan Test

  Test started - 17/03/2016 16:46:26
        
  Finished test:-17/03/2016 16:47:25
  Past

  Surface Scan Test - 2

  Test started - 17/03/2016 16:47:25
        
  Finished test:-17/03/2016 16:48:58
  Past

  I also went in the BIOS BOOT MENU by pressing F12 at startup and ran diagnostics that seemed to have said everything going, however I saw a mistake, faliure in its process that was too fast for me to write the error.

  In a nutshell, my thought is that my hard drive has failed / is corrupted or is about to fail.

  My simple question is, do I need a new hard drive with the information I've provided?

  Thank you very much!

  To all those who read this topic:

  I rang Dell directly and they confirmed my hard drive needs to be replaced.

  8792 power over time, I think that its actually me good.

  Bravo and thanks for the reply ejn63

• Connection to the machine to ESX4 Wizard fails with "connection refused".

  Environment: ESX 4 server, hosting VMware Studio 2.0 (final version), will deploy device created in the same ESX host.

  -

  ---

  In my profile generation, generation settings section, I chose VMware ESX/ESXi 4.x and entered the Connection Wizard...

  Host, Port, user, password fields are filled.

  Connection test fails with the following message is displayed:

  Failed: error connecting to the server " " https://x.x.x.x:443/sdk/vimService ': connection refused

  My initial inspection is that it is probably caused by the server proxy/ISA on our network. It is know to cause some problems with https connections and some browsers. I am not sure that it is the first cause, but this is my first guess.* *.

  There are balls that can confirm?

  Is it possible to force a non-secure http connection?

  No, it's not a way to connect by using http.

  Try the following:

  stop /etc/init.d/VAMI-SFCB

  http_proxy = / opt/vmware/sbin/vami-sfcbdhttp://your_proxy:proxy_port;

  Now, try the user interface.

  Vishwas

• Satellite Pro A10 comes with: error IDE #0, PXE-E61media test failed

  I recently bought a used Toshiba Satellite pro A10.
  When I received it, it was working and being a noob I tried to install a network card and create a wireless network with my desktop using XP when it did not work I plugged my ethernet (from my desktop) cable on the laptop and flashed upwards with a small number can not? dll etc etc.

  Now I unplugged the ethernet cable and when I try to boot my laptop it comes up with:

  "ERROR IDE #0".
  Intel (r) bootagent, FE v4.1.09
  Copyright 1997-2002 Intel Corp.
  PXE - E61: Media test failed, check that the cables
  PXE - M0F: Exit Intel Boot Agent
  Insert system disk in drive
  Press any key ".

  HI Tom,

  The error message that you receive indicate that your laptop is trying to start the connection to the LAN rather than from his own hard drive or a CD-ROM. I suggest that you verify that the boot sequence is specified correctly in your BIOS, or alternatively, you can press F12 during your market and you should get the boot device menu sequence appears so that you can specify that you want to boot from your hard drive.

  Kind regards

• VI Analyzer: the wire under the test object fails with call library function nodes

  Hello

  If I have a knot of function call with an ErrorIn and an ErrorOut library, the VI thread Test Analyzer "Thread under object" always fails with two hits in a library function node call.

  Double click to the salient facts occurrence lines error related to the call... node.

  The test fails, if the error lines are not connected.

  Thank you!

  H

  Sorry, created the CAR number is #208992.

  Kind regards

  Michael

• What is PXE - 61 media test failed error and the error PXE - MOF? What is the solution for this error? It's a lenovo with windows desktop

  I have a lenovo computer. I began as routine but unfortunately it says error:-what is media test failed error PXE - 61 and the error PXE - MOF? What is the solution for this error? It's a lenovo with windows desktop computer? How do I prevent this.

  Kala

  Hello Mohan,

  ·         You did changes to the computer before the show?

  These errors often occur if there are incorrect BIOS (Basic Input\Output System) settings.

  Method 1: Check if the computer startup options are changed in the BIOS. You can set the hard drive as the first boot device. In addition, make sure that this option "Wake on LAN" or one similar to it is off.

  Method 2: Load default BIOS (Basic Input\Output System) settings, and then restart the computer.

   

  Important : Change/update BIOS can be a complicated process, and if an error occurs, your computer could be rendered inoperative. Be sure to observe the instructions of the manufacturer.

• I have a compaq presario cq60 with vista which was able to start after the installation of windows updates. HP recovery failed with error code 100a and bios self-test gave error fail #1-07. What can I do?

  I have a compaq presario cq60 with vista. Could not start after the installation of windows updates. HP recovery failed with error code 100a and bios self-test gave error fail #1-07. I took the hard drive and installed in my office. Windows Explorer displays the main and recovery partitions.

  The primary partition has the following folders (including hidden & system)

  The recovery partition has the following (including the language files more)

  Someone at - it ideas why my laptop does not work?

  Thank you

  Greg

  Hello

  You press F11 on startup with a HP Compaq to start the recovery process.

  For problems with the recovery process, you will need to contact HP.

  BIOS problems:

  There are messages for the HP Forums for posters with similar errors:

  http://h30499.www3.HP.com/T5/notebook-HP-ProBook-EliteBook/notebook-HDD-problems-TEst-status-1-07-fail/TD-p/658902

  http://h30499.www3.HP.com/T5/notebook-PCs-pavilions-Presario/HP-Pavilion-dv8000-getting-1-07-fail-error/TD-p/883284

  http://h30499.www3.HP.com/T5/notebook-PCs-pavilions-Presario/HP-Pavilion-notebook-dv6000-1-07-fail/TD-p/1069457

  All the answers it point to a drive about to fail

  See you soon.

• I can't discover a device ips with the CSM, the connectivity test failed!

  Hello world

  As I say I IC discovering my unit IPS with CSM, I have this message:

  The connectivity test failed. Elapsed time: 0 seconds. Expired certificate expiry of the certificate by the device. Certificate of details he received the device: [[Version: V1 subject: CN = X.X.X.X, OR is SSM-IPS10, O is "Cisco Systems, Inc.", C = us Signature Algorithm: SHA1withRSA, OID = 1.2.840.113549.1.1.5 key: public module of 1024 bits Sun RSA key:]]

  163313595958527341944117022920288114482504180720578005561064955313643774990976715676633248342066152083691325258722628818351428036183713571418359362172457378662626088225882179602799780417125413462000959388084832050518999958663965078068279649170934515615745020420256153072567949117948346991874191887565159544369

  [public exponent: 65537 validity: [from: Tue Dec 07 10:42:59 THIS 2010, to: Fri Dec 07 10:42:59 HEC 2012] issuer: CN = X.X.X.X, OR is SSM-IPS10, O is "Cisco Systems, Inc.", C = SerialNumber us: [-XXXXXXX]] algorithm: [SHA1withRSA] Signature: 0000: E1 DF 3 a 84 EF E5 C8 F5 F8 EB D1 BA C8 55 54 61:... a... T.. U 0010: F8 E4 54 28 0F 0F DB F8 DB CA 0A 5F 63 B0 0E 0C. T. (..... _c 0020: 4 a 28 46 9th D0 B7 B9 F1 A7 B7 35 95 2 CA EB FD J (F...) 5,... 0030:03 32 D1 1A 13 DB B3 9B C9 E2 E6 22 04 D1 84 3 B. 2... ». ;.. 0040:4 4TH BD D2 E0 25 27 46 5F 1 D ED 39 EC 8F 38 BD MN...%'F_... 9.8 0050: BE ED E8 7 02 AE 62 92 89 66 86 BB B4 B6 FD 1F... b... f... 0060:6 46 27 2 4 b EF F8 C9 1F 81 29 82 C1 AB lF 5F 4F,'K... O..._)... 0070:06 33 0D EA THIS 3F 85 CC 2F 82 6 B 8 90 AND 8 B.3 D8 D6...? ... /...k... ] Please synchronize the time settings on the device and the server of the Security Manager and the time-out value of the certificate, and then generate a new certificate.

  I already generate a new key rsa on the ASA FW IOS version 8.4, my connection is ok and my password. I discovered the FW ASA successfully but not IPS module.

  worm CSM 4.3.0 service pack2

  Thank you for your help.

  This is a common problem with IPS and is easily fixed.

  The IPS uses a self-signed certificate for the protection of its channels of management TLS (Transport Layer Security). When an IPS is initialized who signed a certificate is valid for two years. This certificate is separate from the ASA RSA key.

  To regenerate, please see the procedure described here.

  Do not forget to rate helpful answers and mark your question as answered when solved.

• While trying to see Planner installation and operation, the test in local mode, the EXECUTION fails with message "Waiting for the number of virtual machines to register.

  While trying to see installation and operation Planner, the test in local mode with only 1 VM the EXECUTION fails with message "Waiting for the number of virtual machines to register.

  There may be a lot of problems in the desktop VM. Agent service see Planner is not running in VM Office. You can check in the event viewer to see what kind of error occurs. The most usual error missing file IP.txt c; drive or harness IP in the IP.txt produce if there is.

• Storage test 55 certification vmotion, storage vmotion fails with "Could not lock file" on the virtual machine during storage vmotion

  In my view, that it is a known problem in ESXi 5.5 Update 2 release notes, someone knows a solution yet? This is an excerpt from the release notes:

  • Attempts to perform live storage vMotion of virtual machines with RDM disks can fail
    Storage vMotion of virtual machines with RDM disks can fail and virtual machines can be considered in turned off of the State. Attempts to turn on the virtual machine fails with the following error:
    
    Cannot lock the file
    
    Workaround: No.

  VMware support for the record said that the patch will update 3, it is known as an intermittent problem. Finally, it happened to me on the 9th attempt.