Video input

Similar Questions

• Tecra S2 video input

  How can I put on a video input on my Tecra S2. I want to play Xbox 360 in HD on my laptop. Is this possible? Maybe there is a docking station or something like that.
  Hope someone can help me
  Greetz

  Hello

  AFAIK the Tecra S2 has only one exit of S-video port.
  But I put t know how you want to play Xbox? You want to use the laptop as a TV?
  I don t think that it is possible to do.

  Good bye

• Video input to my desktop PC

  I have a desktop HP Omni 100-5050 PC and would like to get video to use as:

  -Monitor (to connect my phone to the pc via the VGA input)

  -Use it as a TV, video receiver connection to pc via / cables V.

  However, I have seen just "video out" port on the pc.

  Is it possible to use it as a video input (vga or AV)? Otherwise, any what possible adaptar to use for this purpose?

  Thank you

  Alex

  Still, your computer has no video inputs or outputs. The ports in your photo are not video outputs.

  

  1 - LAN (ethernet)

• No message signal to s-video input on the screen - how to remove it?

  I pressed a button on my monitor by mistake, and now I have a blue box with the message "no s-video input signal" on the screen at all times.  It's annoying because it's in the upper right corner, covering the buttons I use to close, reduce and optimize windows.

  I tried right click but nothing happens.  How can I get rid of this error message?

  Hi AnneHotmail,

  1 What is the message appear after you restart the computer?

  2 are you able to show display on monitor other than the blue message box?

  3 is this a laptop or desktop?

  I suggest that you restart the computer and check if it works.

  If restarting does not solve the problem, then check and ensure that the monitor is connected correctly to the computer.

  Also try the method below and check if it works.

  (a) turning the computer off.

  (b) disconnect all cables from their bottom or the sides of the monitor (particularly the power cord). Unplug the power supply cord releases all their reset circuit locks

  (c) press and hold the power monitor for 5 seconds button

  (d) plug the monitor power cord

  (e) turn on your computer and check if it helps.

  If the previous step fails, then you will need to consult the manual of the monitor to restore its default settings or contact the supplier of the monitor.

• No video input for monitor and powerless keyboard - computer has the power

  My computer of girls, with the XP system, has the power (power light flashing & the fan) but the monitor receives no video entry and keyboard is dead.  I tried another monitor, but still no video input.  Suggestions for remedy to appreciate.  Thank you, Pat J

  You are more than welcome to help.

  I don't want to throw another curve ball, but I was working on a computer the other day who had the same symptoms as your daughter. The computer would turn on but nothing on the screen. I replaced the graphics card and still no dice. I don't know what made me do but I removed one of the sticks of ram and bam! The graphics was back. This isn't the way that computers are supposed to work. Either the graphics or the ram of the computer must issue codes beep on startup when a component fails. Beep codes each model represents a different problem. I guess what I mean here is you can try to remove one of the sticks of ram and then start the computer. Repeat for each stick. If you intend to go inside a computer, unplug the power cord to the computer before opening the case to work inside. With his unplugged cable press and hold the button for 10 seconds. Make sure that you do not work in an area with carpet covered floor. Repeat these steps each time that you turn off to check a different key. If the icons still do not appear, you are left to try a new graphics card. The one I linked to is a decent card at a fair price. However, if check you with you parts used computer repair shop (not these geeks of department store) you can find out who sells. Tiny most computer stores sell these items and they are generally tested before being put on sale.

• HT-TC 260 Sound does not work via the video inputs

  I recently bought a bar of its HT-CT260.  If I plug the cable box bar using the optical connection, then it works fine.  If I plug the optical connection between the TV and my PS3, then it works fine.  But I get no sound, if I plug the bar directly to the optical input on my Sony KDL-40xbr2.

  Oddly enough, the bar works (TV at the bar) if the TV is on channel antanna, but not if I use the video inputs for my box of cable and the PS3.

  Spend 3 hours with Sony (useless) online support and assistance phone sony (well, but not solves is not the problem).

  The optical plug is designed to produce sounds when the content you watch contains audio digital. (PCM or Dolby Digital® technology) This feature is available on a selection of digital and video streaming shows and is not compatible with the standard of cable stations or analogue.

  The KDL-40XBR2 TV can only output sound via the connection perspective If the TV is using its own tuner (i.e. If the TV is connected to an antenna or direct cable line in the wall) which explains why you do not get sound when using the video inputs because cable box and PS3 use external tuners to your TV.

  If my post answered your question, please click "accept as a Solution.
  This will help other users to easily find their answers when you browse the site of the community of Sony.

• noobie: configuration of the video input of the project?

  A noobie question: setting up a project always throws me since I have unusual videos sizes of graphics that I use as art films - so less standards. Simple, I want to take a video of art existing I have done (computer graphics), get it to the CS6 Pro first, make a few changes, in this case just speed upward and export it réécrirait in the same format/size/specs. Is it possible that I can have the configuration of a project inspired by the video input. Or an easy way to get the exact specifications of good project for the first based on the video input that I have. My video is a mpeg4 is 1440 x 1080 to 25 images dry with no sound. Any help is appreciated.

  -steve

  One of your 1440 x 1080 25 fps clips drag and drop on the "New item" icon

  or right click on one of the clips and select "new sequence of the Clip.

  This will create a properly configured sequence that corresponds to the ratio of aspect and fps of your clip.

• Switching the video inputs

  Hello. I have a Sony KV2585SA TV with 2 RCA video inputs. On one I have connected a DVD player and the other has connected TV satellite. Using the remote control (RM687c) how to move from one entry to another? Thank you.

  Check for no TV/VIDEO button on the remote control to change the entries. You can go through the link below and try to change the video inputs.

  http://www.KB.Sony.com/selfservice/documentLink.do?externalId=C158311

  If my post answered your question, please mark it as an "accepted Solution".

• Qosmio G30 - video input using WinDVD Creator and WinDVR 5 problems

  Hi all
  My G30 (PQL32L) supplied with Windows MCE. It has preinstalled WinDVD Creator 2 and personally I install WinDVR 5 (application of part 3 came with my Plextor ConvertX PX-TV402U PVR).

  Problems:
  1 WinDVD Creator 2: failed to set the TV system. I plugged my video source via the video cable (yellow, white, red) provided and connected to the AV-in port. I chose TV on the HARD drive for the new project. Default WinDVD defined as NTSC but my TV system is PAL. Therefore, input video quality is blurry and cut in two. Once I changed the setting in the software of PAL, the video screen turned black and no response. I have no problem with Qosmio Player with the same configuration of the connection.

  2 5 WinDVR: Application can not start correctly (hang and cannot complete the program) I to my Plextor ConvertX PX-TV402U PVR TV source, then connect it via USB2.0 for G30. My ConvertX works in my office, but failed with the G30. The application cannot start properly and hung. No response yet I'm trying to complete the program, but the screen was always there. When I try to stop my G30 then Windows MCE hung at the "Closing Windows" screen. I have to stop by pressing the button. ConvertX being operation USB cable, it is not achievable in Qosmio.

  Can someone help to solve these or give advice?

  Fine thanks
  Samuel

  Hello

  I copied the film on my camcorder for Qosmio G30 (WXP MCE) without any problem and subsequently created the DVD using Ulead moviefactory program. I also tested it with VHS-recorder. Once again without any problem!

  My camcorder was connected with firewire cable and it has been recognized correctly. VHS-recorder was connected with the aerial cable simply. I was able to record sources using Qosmioplayer (it was just to test because I'm interested, how it works). Movie from VHS-recorder was also possible to record using Media Center Edition.

  I know I also tested it with pre-installed Win DVD Creator but camcorder has not been recognized as usual. If I remember well I put the TV source and that the camcorder is recognized correctly. To be honest I don't like this Win DVD Creator and I have not tested properly.

  So I would like to know what your video source and what you hear in AV-in port.
  Please tell me exactly what cable you use for audio/video data transfer and exact port on your Qosmio laptop?

• Video input with Qosmio G20-108 problems

  Hello
  I try to connect a video recorder/player for my Qosmio G20-108 and have had no luck so far.
  Tried the red-yellow-white cables that came with the laptop, can get sound via the laptop, but no image.

  Then tried the input cable tv/satellite of the RGB output on the video via Media Center but can't get the laptop to tune into the video signal - just says there is no signal detected even when the video player is on and play a tape.

  Any ideas anyone?
  Thank you, Rob.

  Hello

  Qosmio G20 supports a port of 4pol TV In great video (S-video) and a TV S-video output port!
  Don't mix these two ports!

  He must connect the VCR to the * TV * S-video port!

  Best regards

• Qosmio G40 and S-Video input

  Hello my friends,.

  I have a problem here: (...)

  What I want is simple, in theory. I have a VHS VCR, I have a few bands I want to convert it to DVD. I noticed that G40 has a S-Video In, so what I did, buy a cable that is SCART on one side and the other is S-video, I plugged the VCR to the G40, supported to the play in the VCR button, Ulead factory began to Toshiba, but nothing happens, I can not save anything, even to get a picture... the problem is not the cable because I connected the VCR to the TV , the same way (with the same cable) and it shows fine.

  Does anyone have an idea how to do that? I'm really desperate, I searched Foruns and googlled it but could not get a response.

  Kind regards
  Ricardo Monteiro

  Ricardo is not a solution for you. The cable using S-video can only be used for the transfer of video signal.
  Do you have the picture without sound. I don't think so.

  I had similar experiences and I copied the old VHS tapes to my old Qosmio G30. Later, I converted the recorded material and created DVDs.
  My Qosmio G30 has antenna at the port and I plugged my VCR VHS to this port and transfer of video and audio signals. For example I started video on VHS VCR and started Windows media Center and scanned the channels and on channel 33, I saw my recorded material that comes from connected VCR VHS.

  I tried recording with Qosmioplayer and MCE. Using the two options, I was able to use the record option and have video content on the HARD drive.

  I don't know that the same thing can be done with G40. Check it out.

• Qosmio G30: black and white photo via the S-video input

  Hello

  I have a Qosmio G30 Win XP MCE running. I'm watching the TV from my digi via S-video sky box in the port within the media library. The problem is that the picture is black and white and not very good (lots of interlacing artifacts).

  I checked the driver for the 'TOSHIBA PCI DVB-T/Analog Tuner hybrid' and I am running the latest version of Toshiba, I also checked the output settings on my Sky box digi, which are correct. Is there a resolution?

  Thank you.

  Have you noticed the same result with Qosmioplayer and MCE?

• Video input appears tense, when they are imported into Premiere Pro CS6

  I'm on a level of beginner on Premiere Pro, so please be nice if this question is very basic. I'm doing a video that preserves the video resolution of entry exactly. My video entry was a MP4 movie with a resolution of 1440 x 1080. It is a recording of screen iPad using the X-Mirage software. When I opened normally in quicktime format, it seems not tense. However, when I imported the clip in first, the clip appeared tense. I checked the properties of the element, and it proved to have Pixel Aspect Ratio 1.3333, which means that the pixels are elongated. My output sequence was also strained because of this, although the output indicated that the resolution is the same: 1440 x 1080. I tried to comply with the "Clip Mismatch warning' and the result was still a stretched version. Help, please!

  

  

  I'm guessing that first interpreter clip homesick. He probably than her video hdv 1440 x 1080, which is equal to 1.33.

  Go to interpret images and set the format of the pixels to 1.0.

  See if that will fix it.

• Extern sit reageert niet op Sony vaio vpccw1S1e, Fn, F7 (lcd aan/ITU) geen verandering quality: no video input

  Windows 7 op Sony to geinstalleerd, extern sit reageert niet meer. External het sit works met zekerheid wel (very fast).

  At met welke nder toets sn Fn F7 kan ik het scherm inschakelen external?

  Please select your language from the drop-down menu at the bottom of the page to post your question in the language of your choice. The forum in which you've posted is for English only. If you can't find the desired language, support for additional international sites options are by following the link below:

  Kies uw taal vervolgkeuzelijst onderkant van aan ITU of pagina om your question you posten in Taal van uw keuze. Post on the forum without jij het is voor Frans. ALS I niet vinden baking taal, support van jullie voor boven additional international Geraardsbergen kan

  
  http://support.Microsoft.com/common/international.aspx

• Why am I failure analysis: could not detect face in video input when you use the Morph cut?

  

  I kept getting this error and it is solved. Here's how I did it:

  I had the morph cut applied to two sequences nested multi-cames. himself with sequences nested for each camera, who then had an adjustment layer for a class of color Lumetri.

  I cut the part I wanted to morph Cup to the and flattened the original completely to raw clips nested sequences (with all the deleted effects).

  I applied the morph cut between these two raw elements, and then I copied the layer of color on this article with morph Cup.

  This solves the error exception for me. If you have similar effects on your clips, try to remove them and applying on an adjustment layer.