VISA PM6000 time-out

Similar Questions

• VISA Read.vi time-out

  Hello

  Recently I happened to use Labview drivers of NewPort (ESP301) and Lakeshore (Lsci218) and I encountered the same problem of "time out" every time that a Subvi driver called VISA Read.vi for serial communication.

  I first thought has problems with driver Labview provided by the manufacturers, but after trying the pilot different LV from different companies, I started to think that the problem might be the Read.vi VISA itself.

  I use LV2010-spring, also tested with LV2011SP1. Both give the same timeout problem.

  I asked businesses about the problem, they have not found answers, nor they have LV2010 or LV2011.

  Someone had the same problem?

  Screw joint are FYI for what I tested.

  'test initialize.vi 218' is 218 Lakeshore pilot, with a change of the addition of "\r\n" in the "* IDN? the Subvi called VISA Read.vi. and a timeout error.

  "test initialize 218 - md2.vi ' has the same function, but call VISAWriteRead.vi instead of VISA Read.vi. and works OK.

  How can I know that the VISA Read.vi in LV2010 or LV2011 works correctly? or can I replace the VISA Read.vi with LV8.6 one?

  It seems to me that Newport and pilot LV lakeshore have been developed under version LV does not exceed 8.6. and I think that they tried their driver before release or I hope.

  any suggestion is appreciated.

  Xiaofeng

  The version of LabVIEW is not relevant.

  In the read/write, you add the LF/CR. In the other, you add CR/LF.

  Avoid platform dependent end consistent line in the communication of the instrument.

• Time-out in the structure of the event

  Hello

  I try to configure the time-out period in the structure of the 5s event using the loop, as shown in the picture as an attachment. The problem is that this time-out event occurred only when I code debugging and does not happen when I run the same without debugging. Any suggestions on this?

  Thank you!

  OK, just use VISA Read to read the first three octets.  Then do another set VISA Read the number of bytes defined in dlen.  If the data does not, then you will get a VISA expiration time.

  

• Error - the specified i/o operation on Device\Harddisk2\DR4 was not completed before the expiry of the time-out period.

  Original title: XP USB device timeout - is there a solution?

  Under all the circumstces I get: "Windows - Device Timeout" The specified IO on Device\Harddisk2\DR4 did not complete before the time-out expired period.  The drive is a Sony external 150 GB USB2.  The only way to remedy this is turned off and let windows re - recognize.  It stops usually after 18minutes regardless of activity. I did all the USB install no etc no difference.  Please advise as soon as POSSIBLE!  Please not flaky ideas or suggestions.  P.S > I looked the FIX for USB, but it is not specific to my question - if I ask this question instead.

  Hello

  ·        What is the brand and the model of your machine?

  ·        What steps you have tried to solve the problem other that Reinstall USB?

  ·        You did it all change hardware or software on your machine before this problem?

  You can contact the manufacturer of your computer to update the chipset drivers and check if the problem persists.

  Note: Changing the BIOS / chipset can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/chipset can be solved. Changes to settings are at your own risk.

  Hope the helps of information. Please post back and we do know.

  Concerning
  Joel S
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• What does "wireless authentication failed because of a time-out" mean?

  Have a combo unit router and modem.  Having two computers.  You can use the wireless that the other cannot use Wired.  Getting messages like "wireless authentication failed because of a time-out," conflict of IP address and canceled due to the delay.  There was a variety of messages.  We had been able to use a router before, but it would be turned off every two hours or more.  Giving the same messages on Windows Vista.  The other computer is Windows XP Motorola
  modem/router.

  Hello

  1. what security WEP, WPA, etc. Do you use?
  2. is the driver software updated for the router to work correctly on Vista computer?

  I suggest you to follow these steps and check if that helps:

  Method 1:
  I suggest you to check if you can connect by using a different port or a different router in case the problem is with the router itself.

  Method 2:
  You can also visit the link provided below, which offers a similar problem resolution. Check if the steps to help you resolve the problem.
  http://social.answers.Microsoft.com/forums/en-us/vistanetworking/thread/4db4caa0-86bb-4b7b-8aa7-252d5653f063

  It will be useful.

• How to adjust the time-out setting?

  I'm in a certain OBIEE in Firefox which, by nature, do not take a long time to run. One of my local Technical Support people suggested increase Firefox's timeout setting (he showed me how to do this once, but I didn't write it). Can you provide instructions written (or annotated images of the screen), please?

  Alright. There are two ways to do this. You can extend your timeout, or you can completely disable timeout. Depending on how you are using firefox, can be useful. If you want to extend your time-out, type about: config in your search bar on the top. From there, need you a list of preferences. There is a search bar. Type "Timeout" in there. The top two are disable the time-out and the 'County timeout'. If you want to disable the timeout, simply double-click the "enabletimeout" on the top. This will change the false value. If you want to change the value of how long it takes to timeout, double-click on the "CountTimeout" and type in your new value. If this is not sensible, see screenshots.

  Have a great day!

  -Jon

• Please can someone help me for a long time out of the payment itun

  Please can someone help me for a long time out of the payment of itun, I lost my phone.

  This is my information

  ****

  ****

  Thank you

  < personal information under the direction of the host >

  OK so tell me first your reason! It of your personal account, why do you give?

• Apple pay will not be set up on my new 6 iPhone.  When I touch the icon 'Add card' the ball turns just until the screen times out.

  Apple pay will not be set up on my new 6 iPhone.  When I touch the icon 'Add card' the ball turns just until the screen times out.

  Hello...

  Force restart your iPhone > press on and hold the Home and Sleep/Wake buttons for at least ten seconds, until you see the Apple logo.

  Then try to add a card again > define and use the Apple pay on your iPhone

  And make sure your bank / card is accepted for use with pay Apple > Apple pay participating banks and store card

• Stor.E ALU 2s no time-out

  Hello
  I have several Toshiba USB hard drives, that I use as storage media with a cable TV box.
  Type DTP110 turns off after a few minutes if you do not use.
  Type Stor.E ALU 2s continues to operate. There is no point when not in use.
  Desturbing more however is the squeaking noise when the box is turned off, which cuts the power of the forced HD.
  I sent a request for Toshiba if there is a tool to set the time-out, no response.
  Anyone know a solution?

  See you soon,.
  kyriako.

  Hello

  I don't have a solution for you, but I may be able to enlighten us.
  It is likely that the hard drive does not meet the host power management controls.
  I don't think it's possible to solve by any other piece of software, unless it's an update of the firmware.
  If you want you can chech in running a modern Linux host and attaching this player.
  Run the drives under Gnome application and try to read the SMART attributes and / or request a counters.

  The results it will show the way.
  Success at the point of Linux to a kind of incompatibility between the HARD drive and your device.
  Same result in Linux shows that the HARD drive does not respond to these common commands and there is not much to do about it.

  Tom br

  Post edited by: MannerhagenVPO

• error message "kauth resolver external time out."

  Hello

  Pay my iMac (21.5 inch, end of 2013, 2.7 GHz Intel Core i5 processor) bought with Maverick, I went successively to Yosemite and then to El captain. And since then, I have a problem starting not to power: the progress bar stuck at 60%. Start-up in Verbose mode, I get the message "kauth resolver external time out."

  The only solution is to "turn off, is dry, and tension to under 30." This second time under tension, the mac restarts. A solution that is not terrible.

  I used OnyX, but no verification has failed to solve the problem, everything looks ok.
  Who has a solution pour troubleshoot this problem?

  Thank you for your help.

  I too have this problem sporadically with some of our iMacs us upgrades 10.11.3 (from 10.10).  By chance are your iMacs have records of merger?

• I have an iPod hooked up to a Pioneer AVH-X4700BS 160, and nine times out of ten the iPod reads OK TO DISCONNECT.

  I have an iPod hooked up to a Pioneer AVH-X4700BS 160, and nine times out of ten the iPod reads OK TO DISCONNECT.

  It seems normal. What happen?

• A time-out of the finite queue of wiring allows parallelism?

  I have several loops (11) all running in parallel, set up with a producer--> several consumer-> multiple consumer architecture.

  In each of the loops of consumer, I wired the values of time-out on the order of 1 second each of the vi "remove item" which feed on each loop. However, the overall performance of all vi is very slugish.  I have no expectation s vi in the loops of consumer, I guess the time queue supports this feature and allows labview to work its magic of parallelism. This hypothesis is correct?

  For what it's worth, the loop of the producer bed synchronously large shared memory double paintings representing the acquired data and post processed in RT through virtualization (hypervisor). The loop of producer implements an element of expectation. This loop of producer distributes the data to the various queues, depending on the data type meta code embedded in the data of recevied. Then, first consumer level loops review data, update some PLC tags accordingly (via the datasocket connection) and, under certain conditions, send signals well formatted the next level consumer loops that manages storage PDM.

  Each consumer has a dedicated queue and each of them are powered by several producers to the top of the pipe. I put vi waiting in each loop of consumer with a value of about half of the time waiting for data to arrive, and it did not help at all. However, the problem has been resolved by configuring the properties of execution of almost all under vi as priority of subroutine, returning with dedicated allocation of memory. I know it's basic stuff that I should have checked before hand, but everything works fine now.

  Thanks for the help anyway!

• smart camera of the trigger of the time-out value of the error - VBAI 3.6

  Hello that tal?, el tema are that I have a problem with the Smart camera're tengo una fotocelula conectada has the patilla of trigger and (2), el u Trigger-(12) masa in las patillas del conector DB15 of the smart camera para as cuando PASE una pieza realice the fotografia. The cuestion are el solo time-out error me already poner 60000 ms, y for example, so una pieza soon en pasar 60000 ms en el paso of the closing of imagen mas me pone time-out error, y sigue por el diagrama of blocking como if would Fall the imagen. In principio imported me that salga el time-out error, pero me gustaria that esperase has the following pieza sin avanzar por el diagrama of blocking, not so to me explico very well.

  If alguien tiene alguna idea como el problama delivery could be lo agradeceria mucho.

  Cordially, is muchas gracias of photos. David.

  Hey David,

  entonces Perfecto. If the respond you vale marcala como tal in el foro o con UN kudo en knew defecto para as other users themselves can the answer is beneficiar.

  Duro con ello!

  Jesus.

• NI-VISA run-time engine

  When 'building' a LabVIEW program containing NI-VISA under VI (for example to connect with USB), I had problems to get the code 'built' to find my devices NOR VISA, even if the NI VISA's USB drivers are correctly installed on the computer 'target'.

  (The code 'built' will run if the target machine has an installation of LabVIEW to this topic, including NI-VISA)

  -The NI-VISA run-time engine will automatically appear in the 'Build' (because of the Sub - NI VISA VI), or should I specify myself - and how?

  Thank you. Peter.

  Create an installer as you did the executable version.  The installation program will be for the executable, not for the original project.

  What version of LabVIEW are you using?

• How to set up a time-out Message of ERROR.

  Hi all

  I need to put in place a waiting time (for example 400 MS)

  to read sensors for YOU.

  If its not arrive I need to display the error message.

  I implement this in folowing way...

  But I am not satisfied by this method...

  is this good method.

  I've attached my VI file

  

  You can replace the functionality of Count_XL you made by simply using the iteration Terminal at the bottom left of your loop.

  As for make a time-out, you can use the express VI to check if a certain amount of elapsed time and the end of the loop if your sensor is true or time elapsed time.  There are many ways to do it, but the best way will be determined by how you want your app to work.