Vista will not boot

Similar Questions

• I removed a secondary hard drive but now Vista will not boot. I tried startup repair, but failed. What alternatives are there?

  It is a desktop computer that I built myself, so I have no tech support. Until I removed the hard drive, I formatted to remove all data. Since then, Vista does not start. I used my installation disc to repair Vista, but that has failed. I tried the system restore, which was a success, but Vista still does not start. What else can I do to solve this problem.

  Hello itisallgeektome,

  Open Control Panel and click on Administrative Tools. In the Administrative Tools window, click computer management, and then in the next window, click on disk management. When the disk management window opens look down the list of partitions and see if you have a "system reserved" partition This is where the system files are stored.

  If you have installed the drive 'after' that you installed vista, then I accept the boot files would not be on the second drive, but it seems strange that the windows repair option will not correct the bootloader. However, by doing an inplace upgrade this will re - install windows vista (but it will not, or should not affect your files/programs (However it might be useful to back up all the important files that you cannot just in case beed)). As a complete reinstallation is completed, it will create a new bootloader in the process.

  This forum post is my own opinion and does not necessarily reflect the opinion or the opinion of Microsoft, its employees or other MVPS.

  John Barnett MVP: Windows XP Expert associated with: Windows Expert - consumer:www.winuser.co.uk | vistasupport.mvps.org | xphelpandsupport.mvps.org | www.silversurfer-Guide.com

• Vista will not boot corrupted registry and no system restore

  Hi I hope some kind person help me please with my rather urgent dilemma?

  I Went to turn on my laptop and it could not start. (vista ultimate 32-bit edition)

  Instead, he takes me to the windows startup repair, and after a few times of cycling through it, it says
  "cannot repair this computer automatically.

  Signature of the problem
  #1-Autofailover
  #2-6.0.6000.16386.6.0.6000.16386
  #3-4
  #4-262147
  #5-registre corrupted
  #6-Registre corrupted
  #7-999
  #8-3
  Restore #9-Registre
  #10-0
  version of the OS - 6.0.6000.2.0.0.256.1

  I tried to insert disk vendors and changed the boot sequence in the bios, but still takes me to the system recovery Startup Repair (which it does not correct)

  I tried F8 last good config and always the same cycle of system startup repair, then no solution.

  I am at a loss with this, I did something unusual to the laptop until I stopped him, he just decided that the registry has been corrupted.

  I also had a backup on my external HARD drive but boot from it's exactly the same (goes directly into the system repair)

  Surely, I can recover my OS somehow, without losing all my data?

  Any help with this would be appreciated seriously!

  Thank you

  Hello

  Check with your system manufacturer that they all slightly different methods. They may have included a recovery
  Partition or other methods to restore the default value. Also your system manufacturer will sell you the physical disks at a great price
  Since you already own windows.

  What are the system recovery options in Windows Vista?
  http://windowshelp.Microsoft.com/Windows/en-us/help/2b3724d1-f4ad-5b26-16dc-3e9e66f4be5e1033.mspx

  This tells you how to access the System Recovery Options and/or Vista discs
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  ----------------------------------------------------------------------------------------

  Check with your system manufacturer support as they may have understood, Partitions recovery Vista DVD, and/or
  other methods to return to the original configuration.

  Here it is just a few options and you should contact our service system Maker to be sure
  you know all the options you have.

  How to perform a repair for Vista Installation (this keeps your data if the backup off the)
  Player is safe)
  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

  How to do a clean install and the installer with a full Version of Vista - this erase ALL programs and data on
  http://www.Vistax64.com/tutorials/117366-clean-install-full-version-Vista.html

  This tells you how to access the System Recovery Options and/or Vista disk
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  How to do a clean install with a Version upgrade to Vista - this wipes ALL programs and data on
  http://www.Vistax64.com/tutorials/68767-clean-install-upgrade-Vista.html

  How to do a Custom Installation of Vista - this is a clean install should, however, save your data
  http://www.Vistax64.com/tutorials/241565-custom-install-Vista.html

  Upgrade to another edition of Windows Vista - this should keep the programs and data
  http://windowshelp.Microsoft.com/Windows/en-us/help/3af7e05f-4d2a-4af7-A168-9242f9093bb81033.mspx

  Installation and reinstallation of Windows (upgrade - store programs and data or New Installation that removes them)
  http://windowshelp.Microsoft.com/Windows/en-us/help/e77344fa-e978-464c-953e-eba44f0522671033.mspx

  On-site upgrade
  http://vistasupport.MVPs.org/repair_a_vista_installation_using_the_upgrade_option_of_the_vista_dvd.htm

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Startup Repair cannot fix issues and vista will not boot

  I have an asus laptop. A few days ago when I tried to run vista, he began to display a Startup Repair window: If problems are found, Startup Repair will fix it. Then it takes awhile, and then he said that he could not fix the problem, and the details of the problem are:
  Signature of the problem:
  Startup Repair V2
  Signautre problem 1: AutoFailover
  2: 6.0.6000.16386.6.06001.18000
  3: 6
  4: 1114127
  5: NoRootCause
  6:NoRootCause
  7:0
  8:1
  9:SystemRestore
  10:0
  OS version: 6.0.6000.2.0.0.256.1
  Locale ID: 1033

  Can you help me?
  Thank you
  Piotr

  Hello Pelle24,

  Thank you for using the Microsoft Windows Vista Forums.

  I found a site that will guide you through to fix this problem.  Please let me know if this solves the problem, or if you're still having problems.

  Windows Vista no longer starts, and the startup repair does not solve the problem:
  http://support.Microsoft.com/kb/934540 James Microsoft answers Support engineer visit our Microsoft answers feedback Forum and let us know what you think.

• I replaced my motherboard, now Vista will not boot. I can not install either (error code 0 x 8007002)

  I changed my motherboard and now my Windows Vista SP2 does not start.

  I have downloaded and burned a boot from Windows Vista DVD from microsoft.com and I tried to install it but I get a message "this installation has been cancelled. The dialog box shows

  «Windows cannot open the required file D:\Sources\Install.wim...» "Error code: 0 x 8007002.

  Help please?

  "arielca" wrote in message News: * e-mail address is removed from the privacy * .com...

  I changed my motherboard and now my Windows Vista SP2 does not start.

  I have downloaded and burned a boot from Windows Vista DVD from microsoft.com and I tried to install it but I get a message "this installation has been cancelled. The dialog box shows

  «Windows cannot open the required file D:\Sources\Install.wim...» "Error code: 0 x 8007002.

  Help please?

  If your computer has an OEM version (supplied with the computer) of Windows Vista, it is linked to the original motherboard and when you replaced the motherboard the license becomes invalid.  The only exception is if the original motherboard been replaced by or with the approval of the OEM (computer manufacturer) due to a failed motherboard and an exact match is not available.  It would then the OEM manufacturer to provide a license appropriate for the computer.

• Vista will not boot after installed updates

  After installation of .net Framework 3.5 Service Pack 1 for .net Framework Assistant updates. 1.0x86 (KB963707) and Windows Vista (KB968389) to my Dell XPS M1330 laptop, my computer did an automatic stop down. I couldn't restart my computer correctly after this {2nd time this has happened}. I restarted my time 1st comp by selecting the command prompt and the 2nd time by catering to last known position. I did all as usual by pressing F8, F12, F2, diagnostic test, memory test and a little more. Right now I'm running, but I'm going to be scared to do another update when the time comes. Can someone help me please on this issue. Many thanks in advance, Ron

  Hello

  1. keep good backups of your data using redundant methods.

  ------------------------------------------------------

  2. it is very possible that updates do not install correctly are the symptoms of the real problems
  and not the real cause of their.

  ------------------------------------------------------

  3 set updates download but you can install them - and you can install them one at a time if necessary.

  Control Panel - Windows Updates - left settings.

  and run it to restore updates

  How to reset the Windows Update components?
  http://support.Microsoft.com/kb/971058

  ------------------------------------------------------

  4 do these to erase corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  ------------------------------------------------------

  5. record how to remove updates if necessary:

  Control Panel - Windows Updates - lower left Installed Updates - uninstall or change

  Or

  Remove an update
  http://windowshelp.Microsoft.com/Windows/en-us/help/182043da-fc3e-4220-AFBC-d9b09f2b2a1a1033.mspx

  Or

  The problems with the removal of updates
  http://windowshelp.Microsoft.com/Windows/en-us/help/5a319824-5cb5-493d-9151-9a97d0f565b61033.mspx
  Or

  How to uninstall updates in Windows Vista
  http://www.vista4beginners.com/how-to-uninstall-Windows-Vista-updates

  Disable or hide optional updates on Windows Vista
  http://www.howtogeek.com/HOWTO/Windows-Vista/disable-or-hide-optional-updates-on-Windows-Vista/

  ------------------------------------------------------------

  If necessary, you can get free reports of incidents.

  Windows updates - free Incident report

  Go here and click on-> Windows Update fails while searching, downloading or installation of updates
  http://support.Microsoft.com/GP/wusupport#tab3

  The security updates, you can get free support Incident report
  http://www.Microsoft.com/protect/resources/support.aspx

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Computer now put in hibernation, Vista will not boot. Computer stuck on black screen after startup. Help?

  I put my computer on 'Hibernate' when I went to bed. When I woke up, I started the computer learned to manufacturer (HP) computer screen introduction as usual, but windows doesn't not load afterwards, as he usually does: I just get a black screen. Lights supply and all the rest are on. Just nothing happens. Any ideas?

  Can I use the firmware from HP (I guess that's what it is) to confirm that my memory and hard drive are very good. I tried Googling the problem, and some signs indicate a problem with the powercfg parameter. I can't get in cmd.exe to reset because I can't get into windows (although through HP firmware, I can enter in "Administrator: X:\windows\system32\cmd.exe - cmd", which seems the same, but the orders that I see offered on websites do not seem to work - help?). Ditto with Safe Mode. I don't have Vista installation disc.

  Any help is very appreciated.

  Hello

  You need to contact HP and install recovery disks command to perform a repair.

  http://h10025.www1.HP.com/ewfrf/wc/contacthp?LC=en&DLC=en&cc=us

• "Error message: Verifing DMI pool Data data ', 'Boot from CD' and Vista will not start.

  Vista will not start. Yesterday I had a remote assist of a tech trade SPS who took several Java updates and installed the recommended Java version. Until I left work the day I closed my computer so that he could install the updates from Microsoft. After the updates were finished I he turned and left for the day. When I arrived this morning, I had was a black screen and 2 lines of text following: 'Verifing DMI pool data' and 'Boot from CD' and a cursor flashing beneath them. I downloaded and executed a Western Digital utility that showed no problems with the hard drive, put in on the installation disc repair service is no error. I did a system restore to a point since yesterday morning, and Vista still does not start. Any ideas or suggestions?

  Hi JohnHorky,

  Step 1:

  First check and make sure that all physical connections on the computer are correct.

  Step 2:

  Alternatively, you can try to run a Checkdisk and check.

  a. Insert the installation disc.

  b. restart your computer.

  c. click on the Start button, click the arrow next to the button lock and then click on restart. If you are prompted, press any key to start Windows from the installation disc.

  d. choose your language settings, and then click Next.

  e. in the System Recovery Options menu, click command prompt

  f. at a command prompt, type the following command and press ENTER

  Chkdsk /f /r X: (drive letter)

  Note: When you run the checkdisk, there are risks of data loss you can take a backup before starting the checkdisk.

  g. press y when you are prompted to check the drive the next time the system restarts.

  h. close all applications and restart the computer.

  Note: When you run the disk check, there are chances of losing data if you can take a backup before starting the checkdisk.

  Step 3:

  Check if the automatic hard drive in the BIOS (Basic Input/output System) is enabled and save settings and check if it works. If it doesn't, contact the manufacturer of the system for more support options.

  I also suggest that you install the latest update of the basic system of input/output (BIOS) on the computer by contacting the manufacturer of the computer and check if it helps.

  Important: Change to the BIOS/complementary metal oxide semiconductor (CMOS) settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  Hope this information is useful.

• Windows Vista update (April 1, 2011) now the computer will not boot.

  1. Windows Vista update (April 1, 2011) now the computer will not boot.  Love updates been invited but now computer does not start. Just gets up to a certain point, and then restarts. Impossible to start safe mode! Don't know what to do, please help!

  Hi Ema1976,

  Do you have an error message when you try to start?

  Step 1: Disable the automatic restart of the menu advanced startup options and then enter the error message, see the link below:

  Advanced-Startup-options-including-safe-mode

  http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode

  Step 2: Follow the steps mentioned in the link below to access system recoverytools and run the Startup Repair tool again.

  How to access the System Recovery Options menu?

  Run the tool to restart system as shown in the link below
  How to use Startup Repair?

   

• PC will not boot or start the recovery console

  Windows XP 2004

  AMD Athlon XP 3000 +.

  AVG 8.0

  My friend tried to jailbreak his ipod. Now his PC will not boot the OS. It will go to the screen with the options to choose each time you start upward into the safe, normally last good known etc.. Choose one of these options results when control of the PC for the IDE drives and soon after an accident to return to the screen that says "a problem has been detected and Windows has shut down to prevent damage to your computer." I try to start the recovery console, but then I get a blue screen that gives the same spiel, then this Stop error message:

  STOP: 0X0000007B (0XF79BA524, 0XC0000034, 0X00000000, 0X00000000).

  In addition, I changed the boot order in BIOS and tried to use the recovery through an ISO boot console. He ends up crashing this first screen appeared. Even if the BONE is fatal, these guys really want to the GET data out of their hard drive.

  Thank you.

  http://support.Microsoft.com/kb/316401

  http://support.Microsoft.com/kb/324103

  Or, if you just want to back up your data and do a clean install:

  1 remove the drive and put it in a box of USB drive or use a USB adapter. Attach it to a computer that is running a working XP/Vista/Windows7 installation. Use the work of Windows Explorer to copy the data to the hard drive of the system to the rescue and burn data on cd or dvd, or copy it to an external hard drive. I prefer not to do it if I know the drive is infected because he has a chance to infect your host system. In these cases, I use #2 below.

  2. you can start the computer target with a Bart PE (XP only) or Linux Livecd such as Knoppix or Ubuntu and retrieve the data in this way. This has the additional advantage to tell you if the problems you are experiencing are hardware or software related because if the computer behaves perfectly in Linux, you know that Windows (software) is the culprit. Conversely, if the computer behaves badly under Linux, you will know that there is a hardware problem. This is general information on the use of Knoppix for the recovery of data when you do not have Windows:

  You will need a computer with two cd records, one of which is an engraver of CD/DVD OR a USB thumb drive with enough capacity to contain your data OR an external USB hard drive. Download Knoppix .iso image file and create your bootable CD *. If you do this in a previous (XP or Vista) operating system, you will need the third burning like Nero, Roxio or freeImgBurn software (Windows 7 can burn .isos natively). Burn as an image, not in the form of data. Then boot with the CD that you created and the Windows files will be visible under Linux. If you want to burn CD/DVD, there will be a Linux burning program to use.

  * If your computer has only an optical drive and you want to use this drive to burn data or need to test drive, you can create a USB bootable Linux instead of a bootable CD. This site will show you how to do it-http://www.pendrivelinux.com

  http://www.Knoppix.NET
  http://www.nu2.nu/pebuilder/ - Bart PE Builder

  See also - http://lifehacker.com/5504531/the-complete-guide-to-saving-your-windows-system-with-a-thumb-drive
  http://www.howtogeek.com/HOWTO/17044/move-files-from-a-failing-PC-with-an-Ubuntu-Live-CD/
  https://help.Ubuntu.com/community/LiveCD and for future disaster recovery programs - http://www.elephantboycomputers.com/page2.html#Backing_Up

  MS - MVP - Elephant Boy computers - don't panic!

• Vista will not start! Black screen, no mouse, no cursor pointer. Startup Repair cannot repair. Details say 'wrong pass '. What is the correct syntax for pkgmgr to uninstall?

  Vista will not start!  Black screen, no mouse, no cursor pointer.  Startup Repair cannot repair.  Details say 'wrong pass '.  It looks like all the files are well intact on the disk.

  What is the correct for pkgmgr syntax when you try to uninstall an update by using a command prompt when starting Vista OS disk?  I entered the following in the "x:\Sources >" prompt:

  start /w pkgmgr/o: "C:\; /Up:Package_1_for_KB2840149~31bf3856ad364e35~x86~~6.0.1.0 C:\Windows.

  When I run this command it ends quickly and when I run 'echo %errorlevel%' I get '5', which seems to mean 'access denied'.  How am I supposed to have access to remove the patch?  Am I missing something?  Perhaps a switch in the syntax to access?  Help, please.  Thank you.

  I tried both options that you recommended.  As initially stated, no boot option would produce something other than the black screen.  I tried to boot from a drive and restoring the system running, but she didn't, and when I tried to do it again the recovery console could not find restore points. ?.

  An update, the computer is now fixed.  Oddly enough, I ran recovery of starting a drive at least 8 times and each time I checked the details and he said: he ran chkdsk without error and return to the same cause "a patch is preventing windows to start.  I even ran chkdsk c: /f from a prompt command from the recovery disk and it found no errors.  That's when I posted the question above after trying to remove the patch in the manner described above.  After some time and frustration, I decided to run chkdsk /r c:.  It took awhile, but it found 1 bad sector, moved the data, the bad sector tag and finished.  Once I restarted from that, everything came and went very well.

  So, the original question remains, what was missing in the command to run pkgmgr/high: successfully.  And the new question exists as to why start Recovery claims run chkdsk if it does not, or he turns the version/f not the version/r the same as I did manually?  It would be good to know for the future.  Thank you!

• Cloning hard drive with Clonezilla failed, gave a bad sector error message and now the original hard drive will not boot

  Original title: startup problem

  I tried cloning from my hard drive with Clonezilla, and he gave me a bad sector error.  I have since run the hard drive test in bios and it passed.  Anyway, clone has failed, and now the original hard drive will not boot.  My dvd player won't turn when I try to load the Vista repair CD (Vista Home Premium 32 bit).  Clonezilla removes the start settings for the original disc?  And if so, how can I restore it?  The computer starts just a black screen with a cursor at the top left.  When I install the hard drive in a box and connect it to another computer, it shows the partitions and files all seem to be there.

  Hi DougEisenmann,

  Clonezilla is not supported by Microsoft.

  If you are unable to boot from the Vista repair disk then you will need to go into the system BIOS and make sure that it is configured to boot from the DVD drive.

  Check out the link:

  Windows to boot from a CD or DVD

  http://Windows.Microsoft.com/en-us/Windows-Vista/Start-Windows-from-a-CD-or-DVD

  BIOS: Frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/BIOS-frequently-asked-questions

  Important: Change the BIOS (Basic input output system) / Semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  See also the thread which has some troubleshooting steps for this same issue.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-system/Windows-Vista-crashedstartup-repair-wont-launch/49315171-1601-49DD-84fe-50bebd9ddbae

  The above link contains third party links provided by other users.

  Note: The use of third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer

• Network card not working plus-nouveau that bought now PC will not boot!

  Hello

  Mounted LAN realtek network card gave up the ghost so I bought this pci-e card on ebay.

  I installed it in each of the 3 slots of alternative but the PC will not boot with it in.

  This card is not compatible, or do I have to buy something else?

  Desktop HP Pavilion HPE h8-1070uk

  12 gig Ram

  Yes, exactly.

  Here is a link to many others...

  http://www.Newegg.com/product/ProductList.aspx?submit=Ene & DEPA = 0 & Order = BESTMATCH & N = 100006519 & isNodeId = 1 & Description = USB + RJ - 45 + Network + adapt & x = 0 & y = 0

  I would like to know well why these PCIe NIC cards cause the PC does not start.

  People install PCIe firewire cards, cards network wireless, sound cards and all work fine, but .they wired NETWORK card doesn't seem to work.  Not every PC is but several.

  A lot of confusion.

• Satellite L300-1AS - error PXE - boot error - will not boot from USB

  Startup error - error PXE-L300 1AS - will not boot from USB

  I recently bought a new HD to replace the original that my laptop takes an hour to load.

  I put the new drive hard at in the BIOS setting, I chose to boot from USB... USB is recognized as it appears on the screen of the BIOS. I disabled the LAN option as it gives me PXE error... I think that the USB files are not read. as I handed the old HD and attached to boot from USB but it just goes to the start screen.

  I thought that perhaps I bought the wrong HD, but a new appeared on the BIOS setting... I'm a bit confused and would appreciate it if someone could point me in the right direction...

  Any help or advice will be appreciated.

  Thanks in advance.
  Abul

  New HARD drive has nothing to do with it. Problem must be your USB key.
  In your ad you didn t wrote what is on it, and we don t know if USB can operate as boot device or not.

  I put t know what OS you want to install right now but original recovery DVDs or use Microsoft installation disc and install Win7 32 bit. I ve installed on friends L300 and it works perfectly.

• SP2 for Windows Vista will not install. Receive error 800b0100 code. Windows Update has encountered an unknown error.

  SP2 for Windows Vista will not install. Receive error 800b0100 code. I already tried all possible solutions - disabled and even uninstalled McAfee Firewall disabled, ran the CheckSUR repeatedly (see below for the final analysis), tried to install from windows update, also downloaded the stand-alone MS pack, tried selective startup and hidden States of services, still nothing. It has been 2 days work on this. Help, please!

  =================================
  Preparation of control system was updated.
  Binary version 6.0.6002.22202
  Package Version 6.0
  2009-10-24 12:36

  Checking Windows Service Packages

  Checking of manifests package and catalogs

  Checking package Watchlist

  Watchlist checking

  Checking packages
  (f) MOTHER of CBS missing 0 x 00000002 servicing\packages\Package_2_for_KB975467~31bf3856ad364e35~x86~~6.0.1.0.mum
  (f) MOTHER of CBS missing 0 x 00000002 servicing\packages\Package_for_KB975467_client_1~31bf3856ad364e35~x86~~6.0.1.0.mum
  (f) MOTHER of CBS missing 0 x 00000002 servicing\packages\Package_for_KB975467_client~31bf3856ad364e35~x86~~6.0.1.0.mum
  (f) MOTHER of CBS missing 0 x 00000002 servicing\packages\Package_for_KB975467~31bf3856ad364e35~x86~~6.0.1.0.mum

  Control components store

  Summary:
  Seconds executed: 1241
  Found 4 errors
  CBS MUM lack count: 4

  Unavailable repair files:
  servicing\packages\Package_2_for_KB975467~31bf3856ad364e35~x86~~6.0.1.0.mum
  servicing\packages\Package_for_KB975467_client_1~31bf3856ad364e35~x86~~6.0.1.0.mum
  servicing\packages\Package_for_KB975467_client~31bf3856ad364e35~x86~~6.0.1.0.mum
  servicing\packages\Package_for_KB975467~31bf3856ad364e35~x86~~6.0.1.0.mum
  servicing\packages\Package_2_for_KB975467~31bf3856ad364e35~x86~~6.0.1.0.cat
  servicing\packages\Package_for_KB975467_client_1~31bf3856ad364e35~x86~~6.0.1.0.cat
  servicing\packages\Package_for_KB975467_client~31bf3856ad364e35~x86~~6.0.1.0.cat
  servicing\packages\Package_for_KB975467~31bf3856ad364e35~x86~~6.0.1.0.cat

  Hello Yiratr,

  Thank you for using the Microsoft answers Forums.

  Solution:

  Follow the steps in the web link below.

  http://support.Microsoft.com/kb/956702

  That should do the trick for you.

  Thank you.

  Kind regards

  Augustine.

  "URGO".

  UDAY $012 please let me know that whether the solution worked or not, I thank you and appreciate your comments. URGO