VLAN Interface State constantly disabled

Similar Questions

• is excluded them VLAN interfaces in the GAL

  Hello community,

  I have a problem with the configuration of LAG on Cisco SFE2010P 3xSwitch battery.

  The switch has in fact only web GUI. Console - too, but it is not very useful.

  I need to configure Interfaces 1/g3 and g3/2 in one SHIFT. And VLAN (vlan by default) of 60 and 110 (voice), through to allow.

  After that I configured the LAG with both interfaces, "Port of Vlan" LAG settings show me the vlan 60 is untagged and vlan 110 is labeled.

  But if I take a glance on the 1/g3 Interfaces and "Port to LAN" settings 2/g3, both VLAN interfaces are "excluded". I can't access the default gateway, which is directly connected with this settings. The default gateway is a 3750Stack whose address IP of HSRP. It has two uplinks in port the SFE2010P channel.

  I have only one Interface to 100 Mbps on the SFE2010P connected to a trunk on the spine interface. And it works in this way. But using the links LWL LAG now does not work.

  Why are the VLAN 60 and 110 is excluded on the interfaces in the GAL and how can I change it? Thank you.

  Thank you

  Sergej

  Hi Sergei, you cannot configure the individual port within an OFFSET to a vlan. When you join the VLAN, you must select the offset group, not the individual port.

  -Tom
  Please mark replied messages useful

• How to add a button state is 'disabled '?

  I have a Navigation Menu of the main FLASH Web Site that has (7) buttons (BUTTON real objects created in Flash - no MovieClips) that undertake different HTML pages. Everything works perfect (rollover States, links, etc.), but I can't understand how to write code AS3.0 to create a State "button disabled? I've seen a few code snippets that talk about this, if you use MovieClips, but how can I do a 'Button' disable after clicking on?

  I guess I would need a variable that would capture and store the last button clicked?

  Any help would be greatly appreciated that I keep coming to this same issue.

  Here is my current code that makes the buttons work:

  var mainButtons:Array = new Array(mainBtn0,mainBtn1,mainBtn2,mainBtn3,mainBtn4,mainBtn5,mainBtn6);

  var mainButtonsURLs:Array = new Array ("http://www.thekentcompanies.com/Pages/index.html","http://www.thekentcompanies.com/Pages/WhatsNew.html","http://www.thekentcompanies.com/Pages/Facebook.html","http://www.thekentcompanies.com/Pages/Golf.html","http://www.thekentcompanies.com/Pages/Motorsports.html","https://thekentcompanies.tms.hrdepartment.com/cgi-bin/a/searchjobs_quick.cgi","http://www.thekentcompanies.com/Pages/Register.html" ");

  function loadMainPageToFrame(event:MouseEvent):void {}

  var count: Number = mainButtons.length;

  var: index number;

  for (var i: Number = 0; i < count; i ++) {}

  { if (event.target.name == {mainButtons [i] .name)}

  var myURL:URLRequest = new URLRequest (mainButtonsURLs [i]);

  navigateToURL (myURL, "_self");

  }

  }

  }

  for (var i: Number = 0; i < mainButtons.length; i ++) {}

  mainButtons [i] .addEventListener (MouseEvent.CLICK, loadMainPageToFrame);

  .mouseChildren mainButtons [i] = false;

  }

  This is a link to a source file, so at most, you will see a window asking what you want to do with it.  You may need to right click to get an option to save the target file.

• Interfaces reset when disable signature.

  Hi guys.

  When I have the following script penetration in order to disable the signature, the cisco Ips 4240 interfaces are restart, anyone has any clue is so extrange just for the deactivation of a signature?

  end of config

  Service signature-definition sig0

  signatures 9202 0

  status

  fake license

  output

  output

  13 August 23:59:35.229: % LINEPROTO-5-UPDOWN: Line protocol Interface GigabitEthernet1/0/25, changed State to

  13 August 23:59:35.280: % LINEPROTO-5-UPDOWN: Line protocol Interface GigabitEthernet2/0/26, changed State to

  GigabitEthernet1/0/25 is up, line protocol is up (connected)

  Equipment is Gigabit Ethernet, the address is e8b7.4843.b099 (bia e8b7.4843.b099)

  Description: * IPS - A *.

  GigabitEthernet1/0/26 is up, line protocol is up (connected)

  Equipment is Gigabit Ethernet, the address is e8b7.4843.b09a (bia e8b7.4843.b09a)

  Description: * IPS - B *.

  Tahnk you.

  Check the attached picture. It may be useful:

  

• Card crypto applied to the Vlan Interface of the 1841 router

  Currently, our 1841 router has a T1 connected to the WIC T1, Comcast Cable connected to Fa0/0 and the local network connected to Fa0/1.  Tuesday, our 1841 will have an ethernet connection to a new gateway router instead of use the WIC T1.  I added a 4-port ethernet module to the router in the anticipation of this change.  Since the 4-port module is not layer 3 capable, I created a virtual local area network so that I can address the Vlan with the IP address that has been previously configured on the WIC T1.  My goal is to move our IPSec vpn tunnel interface series interface vlan newly created.  I was able to add all orders of the interface vlan, but I wanted to make sure that when the time comes to make the transition, the tunnel will be actually get when it is configured on an interface vlan that is then assigned to one of the four ethernet ports in the add-on.  Has anyone done this or seen that fact?  Potential drawbacks?  Thank you very much!

  Hello

  Crypto-map is compatible with the IVR, so if everything else is in place, it does not work.

  HTH

  Laurent.

• FWSM and multiple-vlan-interface command

  Hello

  I am due to configure a FWSM in an IOS 6513 running, I suppose that the example configurations are quite similar, when you use an MSFC, but I have a question.

  I have 3 inside VLANs, configure 3 LAN interfaces VIRTUAL with IP addresses (as a default gateway for hosts on 3 VLANs), then set up another VLAN separated for a "next hop" between the router and the inside deals with the interface of the FWSM, put the IP on the router from VLAN and FWSM inside?

  I tried this on a test set up and it seems to work but when I ping one external host through the FWSM I couldn't see not all packages using DEBUG ICMP TRACEL, PING did stop working when I removed the ACL on the FWSM inside the interface.

  I used the command INTERFACE MULTIPLE VLAN FIREWALL but after reading all the documentation I think now that I'd rather avoid this command.

  I want to just make sure that I was not without going through the FW

  Any help appreciated

  Regards Tony

  I'm a little confused by your description, but it sounds as if you have it set up correctly. It is expected that you would not see the output of the "backtrace icmp" packet ICMP will * by * the FWSM. The reason for this is because as the FWSM 'fast switches' packages when the connection has been established. The debugging process run in the complex of PC which is basically 3 layers of treatment in the stream. Initial connections and traffic * to * the FWSM itself are dealt with in the complex of PC. Therefore, this is why you have seen the debugging when you ping the FWSM directly. Remove the ACL was probably the best test to see that everything worked. As long as you only have a SVI, then there is no possible way for packets routed in the MSFC. The FWSM is the only thing that can get in the above scenerio.

  Hope that helps to explain the questions a bit.

  Scott

• Configuration of VLAN interface network invited only.

  I'm running CentOS 2.6 and I try to configure the VLANS on a host only interface.  I get an error invalid argument of vconfig.  VLANs are not supported on host-only networking?  I have searched around for a while but you have not found a clear answer.

  Interesting, because on my host OpenSUSE 11.1 x 64, the same command vconfig works very well. I have not tested the VLAN later, but certainly not error:

  #vconfig add vmnet1 900

  VLAN with VID added == 900 to IF -: vmnet1: -.

  #

  Guy Leech

  VMware vExpert 2009

  ---

  If you have found this device or any other answer useful please consider the use of buttons useful or Correct to award points.

• Problem with series Printer B110a printer - State constantly displays Idle

  Hi - I am unable to print a document from my Mac OS X 10.6.8 Version.  The printer is a HP Photosmart B110 all in one printer and has no problem in the wireless network test report.  The print job appears in the print queue, but the State remains on inactive.  I can scan successfully of the printer but cannot print any document.  Print test page printed OK but has been very slow.  I tried all the troubleshooting steps recommended by HP Support FAQ such as the abolition of the printer and reinstalling the driver.  Nothing works.  Any suggestions?

  Hello, welcome to the Forums! I hope you enjoy your experience

  I noticed your post on your Photosmart B110 model does not print. I want to offer my suggestions you that can help.

  • Repair disk permissions
  • Mac OS X: how to reset the printing system
  • Add the printer again

  This is a direct link to download the printer driver: HP Photosmart full feature software and drivers - Mac OS X v10.4, v10.5, and v10.6

  I hope that my post was information!

  Have a great day!

• Taskflow dynamic array and reset the user interface States

  Hi team.

  I use JDeveloper 11.1.2.4.

  I have a nice flow dynamic bounded task that has a view main activity.  Links to view activity change as part of the workflow.  The workflow is initialized with a navigation event.  The display shows just a table of data corresponding to the navigation event.  The table is sortable.  It all works very well.

  The challenge that I meet is that users do not want details of the sort on the table has persisted between navigation events.  So they select NavA, the query executes against ViewA.  They select NavA, they query executes against ViewB.  The table and the activity of the view are the same.  And, during the navigation, in the framework of task flow not related, the display does not actually change in the region.  It is updated with the appropriate data, but the genre are also persisted.  It feels like the client stores the State of the table that I'm not able to remove the sorting criteria of the Rich Table via a managed bean.  Certainly, it feels like what must be launched from the client instead of a managed bean. I don't want to add buttons to view activity to do the reset, because users want this to be triggered by the navigation event.

  If I spend a dynamic unrelated workflow and to return to the dynamic workflow, so details are reset beautifully.  However, this is not an option for the users.

  Any suggestions on the approach would be appreciated.

  Thank you

  
  BradW

  OK, so I had to add this feature to my menu:

    public void setResetMainRegion(String regionName){
      if (regionName != null && !"".equals(regionName)){
        UIComponent mainRegion = JSFUtils.findComponentInRoot(regionName);
        RichTable table = (RichTable)JSFUtils.findComponent(mainRegion, "DynamicCodeTablesTab");
        if (table != null){
          List sc = new ArrayList() ;
          table.setSortCriteria(sc);
          AdfFacesContext ctx = AdfFacesContext.getCurrentInstance();
          ctx.addPartialTarget(table);
        }
  
      }
  

  The thing is that we must find the component, as it is extremely difficult to work with PageFlowScoped managed beans that have been created to support tables.  Such a simple fix, it took you a while to understand where the issue should be resolved.  It seems that some of these issues have to keep longer appears outside the BTF.  Not ideal because this introduces too many dependencies.  Trying to minimize as much as we can.

  BradW

• 11gR2.3 JDev/ADF Faces: the Shell of the user interface, how to disable scrollbars of the logo

  I put a logo in the header by using the attribute UI Shell model property "logoImagePath". During execution of the page, I notice that if I resize the width of the browser to a value less then the width of the image, horizontally and scroll bars vertical appear. This is not desirable, and I'm looking for a way to disable the scroll bars. Any suggestions on how to fix this?
  
  Thank you
  Wes

  I guess for this, you must edit the template. I don't have the shell ui at hand model but I think that the image is child of a scrolling type panelgroupLayout. When the browser window is resized below the width or the height of the Panel group you get the scroll bars. To change this, you will need to remove the panelGroupLayout and just use a group.

  Timo

• Am I the only one to have a problem with the zoom is constantly disabling feature?

  Running iOS on a 6Plus 9.3.3, I continue to turn on zoom and nearly every day he himself turns OFF. Am I the only one experiencing this bug?

  I have not read this "bug" here before, and I read these forums almost every day. I don't know what to offer another standard "fixed".

  Force restart. Hold down the Home and Sleep/Wake buttons at the same time for about 15 seconds, until the Apple logo appears. You won't lose anything.

  The system restore. First save your device via iTunes. Also import your photos on your computer and copy all the data if possible. Reconstruction of the support first test and test. If this does not help, you may need to restore as a new and reconfigure from scratch as the backup may be damaged. It is important to have your photos and your saved data separately from the backup. Here are the steps for a restoration:

  https://support.Apple.com/en-us/HT201252

  If the steps above do not help, you may need to test in an Apple store.

• When windows starts up, the Windows security center / virus protection indicate that the State is disable. Then after about two minutes, he's back back show that the State is turning

  1. about date of first notice this behavior about 3 weeks ago.

  2. subscription of BitDefender Antivirus date about 19/07/2010 expires on 18/07/2011.

  3. no application for protection antivirus has been installed before installing Bitdefender Antivirus because this application installed after Format my machine.

  4. before the formatting, I was also using Bitdefender Antivirus 2009, but after using AVG Antivirus free - trial and I never use free trial Norton or McAfee for this machine.

  Between

  I never use Norton or McAfee free trial for this machine.

  Note that I didn't ask if YOU had never used or installed a trial free Norton or McAfee, I asked if a such Norton or McAfee free trial camepre-installed on your computer when you bought it?

  If that were the case, the test free Norton or McAfee have been re-installed, but not valid, when you reinstalled Windows. If this is the case, you MUST uninstall the free trial AND download/run a specific removal tool & restart BEFORE you install updates or Service Packs and upgrades of IE AND BEFORE installing your new antivirus application (for example, BitDefender).

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• connection statistics is unknown, the service to detect this State is disabled. How can I solve this problem?

  network connection status unkwown

  Check if the following services (responsible for the internet connection) are the value automatic and started.

  ·         DNS client

  ·         DHCP client

  To do this:

  1. click on start

  2. type services.msc in the search bar

  3. open services.msc

  4. search for the above mentioned services and start the services if they are arrested.

  You can also run the tool the Network Diagnostics by right-clicking the network icon in the notification area, then click on diagnose and repair. More information in the link: http://windows.microsoft.com/en-US/windows-vista/The-doctor-is-in-Using-Network-Diagnostics-in-Windows-Vista

• How to view associated with an interface VLAN IP address?

  I have a 6224 with some VLANs set up. I have addresses assigned to most of VLANs (i.e. "configuration, interfaces, vlan 20, ip 192.168.20.254 address '). I can't seem to find a way to have the switch shows that vlan interfaces have this ip assigned, either the CLI or from the web interface. It does not help that I don't think that the web interface even exposes settings for this at all.

  Thank you

  Scott

  
  

• XConnect - interface vlan

  Hello

  I can create Tunnel Xconnect (OVER MPLS NETWORK) between the Vlan interface to the physical interface on the other site?

  For example:

  site 1:

  interface GigabitEthernet7/2.88
  Xconnect 1 Site Description
  encapsulation dot1Q 88
  XConnect 1.1.1.2 88 mpls encapsulation

  Site 2:

  interface Vlan 88

  Xconnect 2 Site Description
  IP 192.168.2.2 255.255.255.0

  XConnect 1.1.1.1 88 mpls encapsulation

  anyone tried this type of installation?

  Thank you

  Alon.

  Hello

  Yes. It will work.