Vmware esxi version

Similar Questions

• R710/R720 - Dell customized Image of VMware ESXi 5.5 Update 2 - megaraid_sas version specific?

  That I improve a R710 and two v5.5 (Dell image) to v5.5 U2 ESXi ESXi R720 using the image of Dell here:

  www.dell.com/.../DriversDetails

  The documentation "Upgrade Guide to ESXi 5.5 using Dell customized Image" here:

  www.Dell.com/.../manuals

  indicates that a specific version of the megaraid_sas driver must be installed.

  Is the version megaraid_sas that installs with the image of Dell U2 v5.5 not the right version?

  I just ran the upgrade on a R710 and it's the megaraid_sas version installed:

  ~ # vmkload_mod s megaraid_sas | grep Version
  Version: Version 06.803.73.00, build: 1331820, Interface: 9.2 inspired: August 22, 2014

  Thank you.

  Hello

  It lists the R720 and R710 systems supported and both link to the same page, so the customized version is the same for both servers. Is the version listed in the reference guide for A02

  megaraid_sas - 06.803.73.00

  Page 5 ftp://ftp.dell.com/Manuals/all-products/esuprt_software/esuprt_virt_solutions/vmware-esxi-5_Reference%20Guide6_en-us.pdf

  This is the same version that he shows for your installation on the R710 so that seems correct.

• VMware Server Version 2.0.2 - migrate VM to ESXi 5.5?

  Hey guys

  I use an old Dell T410 with VMware Server Version 2.0.2 (Build 203138) server running on top of serving 2008R1.

  I'm looking to install a new server and you want to run ESXi 5.5.

  Is it possible to convert VM VMware Server Version 2.0.2 (Build 203138) to ESXi 5.5?

  Otherwise I'm running Shadowprotect. If I can't convert, is it possible to do a HIR to ESXi 5.5 from an image of a VM from VMware Server Version 2.0.2 (Build 203138) Shadowprotect?

  Finally, I was looking for to run ESXi 5.5 Essentials (not more) on the new physical host and then use the old host as a temporary backup with ESXi 5.5 too. I have to buy 2 x 5.5 ESXi licenses to run it on both machines?

  If you want more specifications about the network made me know.

  Kind regards

  Aaron

  Hello

  You must convert the virtual server computers to be able to run on ESXi 5.5.

  Take a look at this, it is perhaps useful:

  How to migrate computers virtual vmware server to vSphere, ESXi

  On the essential, it allows to manage 3 servers (servers esxi) with up to 2 processors of each:

  Editions of vSphere, vSphere is? Leading Virtual Infrastructure | United States

  But, with just the basics, you will be things like HA.

  Best regards

  Pablo

• VMware esxi 3.0 cpu limitation free version?

  Is there a number of cpu, you can use the free edition with vmware esxi 3.5?

  We're going to get a server who is 2 x processors intel quad core and I wondered it esxi will see a single processor even if there are 2.

  Thank you.

  The maximum number of processors can use the free version of ESXi is identical to purchased versions - http://www.vmware.com/pdf/vi3_35/esx_3i_e/r35u2/vi3_35_25_u2_3i_server_config.pdf which is 32 hearts

  If you find this or any other answer useful please consider awarding points marking the answer correct or useful

• Version numbers of VMware ESXi, ESX, (confusion)

  Hello

  I have a case of support for Adaptec about the inability to manage my RAID array (on a map of Adaptec RAID 3405 controller) go in VMware ESXi 3.5. That's what they told me 'Nucleus OSin fact currently VMWARE ESX - i is not supported. Sorry, I should have mentioned this in my previous answer, I was not aware that there is a difference in the standard implementation of VMWARE ESX 3.5'.»

  Is there a VMware ESX 3.5 as a VMware ESXi 3.5 aswell? What is the difference? I thought VMware ESX ended with version 3.0, replaced by VMware ESXi 3.5 and later versions?

  If I look at the operating systems supported for the Adaptec RAID 3405 controller I find "VMware ESX Server 3.5"...

  ESXi and replace DO NOT ESX.  The reason why I gave you the comparison is because you can see what each call to savings.

  ESXi, is short, ESX less the service console.  Both are Virtualization platforms.

• BB10 Simulator on Vmware ESXi

  I'm trying to get the BB10 Simulator to work on a VMWare ESXi server. Here's what I've done so far:

  1. Installed the Simulator on yhe development machine, started VMWare workstation, open the vmx file and downloaded the VM on the ESXi server.
  2. Disabled 3D acceleration on the machine virtual (on ESX) and selected 'Full touch safe mode' after starting the virtual machine.

  At this point, the virtual computer screen displays the IP 'telnet ftp ssh qconn', the axis of the device and the build number.

  The next step is to connect the Momentics IDE to this virtual machine.

  The Simulator is in need of a vmx file configuration dialog box (likely to run vmware specific commands). In the configuration of ESXi, there is no vmx file.

  If I try to connect to the virtual machine by IP address, I need a device password, I did not.

  Someone at - it suggestions on what do I do now?

  In response to my own question because I found the answer:

  Now that I have the IP address, I just follow the steps described in

  http://supportforums.BlackBerry.com/T5/native-development/BB10-native-Cascades-SDK-not-connecting-to...

  Because I had never set up a password for the Simulator, I left the empty password field.

  Copy-paste the details:

  Of your IDE

  -Right click on your project in the Project Explorer

  -Go to Blackberry tools and click on configure target...

  -Click Add new target it... button and enter the IP address of your Simulator in the host name or IP address field, enter your password if you have one then click on finish

  To run your application on the Simulator:

  -In the Project Explorer view, double click on file bar - descriptor.xml, then click on chip Debug Set button to set the author of the application information.

  -Set the configuration of the correct version for the Simulator first by right-clicking on your project and selecting Configurations of Build > Set Active > 4 Simulator-Debug.

  -In the Project Explorer view, right-click the project and select build project.

  -Right click on the project again, and then select run as > BlackBerry Application C/C++.

• Firesight Management Virtual Center in ESXi version 6

  Hi all

  Is it possible to install any version of virtual appliance Firesight Management Center of vmware ESXi 6?.

  Thanks and greetings

  I have not tried it personally - it may be possible to install.

  However ESXi 6.x is not a supported platform yet. Even with the power of fire (new name for FireSIGHT) recently published Management Center 6.0, the supported versions of ESXi are 5.1 and 5.5.

  The source of this information is the Release Notes:

  http://www.Cisco.com/c/en/us/support/Security/Defense-Center/products-re...

• OpenManage for VMWare ESXi has no possibility of tasks of virtual disk

  OMSA v 7.1 and 7.2 for Windows (and earlier versions) allow the user to perform many tasks on virtual disks, including reconfiguring - expand a RAID array with a new drive.

  This is not true for managing open for VMWare ESXi - although you can monitor the status of the RAID and disks with the browser of the OMSA interface type, you cannot perform tasks - can not even make a high beam Flash.

  It is a huge problem, because the PERC controllers (H700 and H800, for example) don't allow you to develop virtual using hard drives not Dell disks when you try this during startup in the bios.  (These controllers only allows you to create new virtual disks using drives not Dell).

  This test was conducted using the latest firmware (12.10.4 - 0001 A10) and drivers for the H700 and H800 and multi-server r610 ESXi 5.1.

  Other people with VMWare have been affected by the present?  The only solution is to have two player networks connected to the computer, and create a simple Windows with OMSA, boot in Windows Server to expand the table using OMSA for Windows.

  I would be interested in the comments of others, including those of Dell.  We spent hours on the phone with Dell; This seems to be the only solution.  (Yes, Dell released a firmware version last year that has ceased blocking non Dell readers, but it only works for the creation of a new virtual disk, do not expanding one existing).

  Yes.  It came through a discussion in the Dell | Servers | Discussion of the RAID community.

  en.Community.Dell.com/.../20263442.aspx

  There is a CD bootable linux called OMSA Live that you download from PowerEdge (linux OS) systems management.

  This OMSA PERC H700 and H800 control and allows you to do everything.  When you reconfigure the RAID and the PERC card starts the reconstruction, although it seems risky, you can restart under VMware and the reconstruction of the RAID continues on.  And you can analyze with OMSA for VMware.

• Free ESXi version limitation

  Where can I find a complete list of the ESXi version free limitations and characteristics?

  Have changed since version 5.x?

  Concerning

  Marius

  • Number of cores per physical processor: no limit
  • Number of physical CPUs for each host: no limit
  • Number of logical processors for each host: 480
  • Maximum vCPUs per virtual machine: 8 Maximum
  • No support of VMware.
  • No vStorage APIs available.

  Free virtualization with VMware vSphere Hypervisor (ESXi) | United States

• VCenter Server first to 5.5.0U3b update and later update of VMware ESXi ESX / will I have problems?

  Hello

  have trouble when I first updated my signature single vCenter Server and later update my vSphere hosts?

  A vCenter Server Version 5.5.0U3b should be able to manage vSphere Host Version 5.5.0 GA, right?

  Kind regards

  Roland

  The vCenter Server 5.5 update 3 b can manage VMware ESXi ESX release GA to 5.5 5.5 update 3 b, take a look: VMware product interoperability Matrices

  BUT, according to the interoperability matrices and vCenter Server 5.5 update 3 release notes, VMware strongly recommends you upgrade your hosts to 5.5 update 3 b, see:

  What's new

  • Update Support for the SSLv3 Protocol is disabled by default
    Note: In your vSphere environment, you must update vCenter Server vCenter Server 5.5 update 3 b before the update to 5.5 ESXi ESXi update 3 b. vCenter Server will not be able to manage 3B ESXi 5.5 update, if you update ESXi before update vCenter Server to version 5.5 update 3 b. For more information about the sequence in which vSphere environments must be updated, see KB 2057795.

  • VMware strongly recommends you update ESXi hosts to ESXi 5.5 update 3 b management of vCenter Server 5.5 updated 3B.

  VMware does not recommend the reactivation of SSLv3 because of the vulnerability of POODLE. If all you must enable SSLv3, you must activate the SSLv3 Protocol for all components. For more information, see

  KO 2139396

  .

  • Resolved issues. This version of vCenter Server 5.5 update 3 b solves the problems that have been documented in the resolved issues section.

• LSI MegaRAID Storage Manager on VMware ESXi 4.0

  Hi guys,.

  We tried to install on VMware ESXi 4.0 MegaRAID Storage Manager (IBM x 3550 M2) and it uses Controller RAID MegaRAID SAS 8808E to monitor the hard disk status but could not be able to install and it returned the error as attaché

  We followed the procedure as shown in the following ibm Web site

  1.6 MegaRAID Manager storage system to a VMWare ESX Server

  Follow these steps to install the on a MegaRAID Storage Manager

  VMWare ESX Server:

  1. download the latest MSM to ibm.com

  2 unzip the and copy MSM_linux_installer - 501.01.tar.gz on a USB key.

  3. from the ESX Server, in the console root, type the following command

  to identify the USB device: fdisk-l

  4. type the following command: mount/mnt/dev / {name of the USB device}

  5. type the following command: cd/mnt

  6. type the following command to copy MSM_linux_installer - 501.01.tar.gz in the occupied Palestinian territories

  file: cp MSM_linux_installer - 501.01.tar.gz / opt

  7. type the following command to decompress the package gunzip MSM_linux_installer - 501.01.tar.gz

  8 type the following command to unzip the package tar - vxf MSM_linux_installer - 501.01.tar

  9. replace the directories with the path/opt/disk

  10 tapez./vmware_install.sh to install MSM

  11. Select version of VMware

  a. enter 1 to install Vmware 3.5

  b enter 2 for VMware 4.0 install

  12. Select the storlib option

  a. Enter n If you want to use the Inbox storlib driver

  b. Enter y if you want to install the storlib delivered with MSM

  IBM recommends 'y' is selected for use packed with MSM, storlib by selecting "n" can

  cause some features of MSM does not function properly

  I would like to know if I use the correct version of the Storage Manager Application MegaRAID for VMware ESXi 4.0

  
  

  If not could someone please advise on how to proceed with the installation and troubleshooting

  Please find the file of errors as attaché

  
  

  Greatly appreciate your help

  
  

  Thanks in advance,

  Vignesh
  

  Check if help: vSphere unknown health status ' vSphere ' eMware »»

• HP Proliant Gen8 DL380e not charge controller B320i with VMWare ESXi 5.0 U3

  Hello community.
  
  Iam trying to install VMWare ESXi 5.0 U3 on a HP Proliant DL380e Gen8 server that has a B320i controller, I'm using support custom installation of HP, but yet when I select target the device doesn't show anything, I tried to raid 1+ 0 and raid 5, but I get No result.
  
  Ce is ISO which I download.
  

  https://my.VMware.com/Web/VMware/details?downloadGroup=HP-ESXi-5.0.0-U3-OCT2013 & ProductID = 229

  
  try Added to ISO customize the controller driver, but the ISO tells me that that driver already exists.
  

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?swItemId=MTX_0a122ebcbbac4c469ca9acd1ae

  
  In le BIOS J’ai activated the next option.
  

  http://h20564.www2.HP.com/hpsc/doc/public/imageServlet?docid=emr_na-c03907472-1/c03871500.jpg

  You can try the custom HP VMWare 5.5 ISO instead? Or do you need a reason 5.0 any?

  I'm running a Gen8 DL380e with 5.5 Update 1 without problems. 5.5 Update 2 has some problems about the new version of the hpvsa driver that gives massive drops in virtual machines to run.

  You have a BBU (battery backup) installed?

  It is also for the execution of the last PSP (Proliant ServicePack) to get the latest firmware and the BIOS before installing.

• How to span multiple LUNS on one (or less) data store (s) in Vmware ESXi 4.1 vSphere environment?

  Hey guys -.

  I currently have 2 hosts ESXi (version 4.1u3), 1 vCenter Server and 1 EMC VNXe3300 SAN (20 to via iSCSI) that make my virtual environment.

  On the EMC is, you create VMware Datastores (which have a limit of 2 TB) then connect these data storage to VMware ESXi hosts.  Once logged in, would continue it the process through the Add Storage Wizard via VMware to connect the disk/LUN storage via iSCSI.  Ultimately, the Lun (s) would then be accessed through the virtual environment (in the Configuration > storage > data warehouses) as generally expected.

  Due to the limit of 2 TB (both on the CEM, Version of VMware and VMFS3) on data warehouses, I find myself with having several data warehouses being created on the side of the EMC and VMware (see photo) appearance.  I know that's not rectifiable via CEM level, but I was wondering if there was any way for me to bring together all these data stores on the side of things VMware.  This way rather than navigate to Configuration > storage > data warehouses and separate iSCSI indicator 6 data warehouses, it would just be a (or more, but less than the existing) data store; It would then extend in all actual data stores that I would.

  I don't know what the appropriate terminology is used to describe it, but I hope someone can help me to what I want to achieve.  Or at the very least, can you please steer me in the right direction.  If this isn't something that can be achieved or it is discouraged, what are the other options which would be recommended?

  Thanks for the help.

  Have a look here: VMFS extended - are they bad, or simply misunderstood? VMware vSphere Blog - VMware Blogs

• Configuration of IPSec in VMWare ESXi can be applied to virtual machines running?

  Hello

  I have an operating system running inside VMWare ESXi 5.1.  Let's call is "MyLinux".  It is a modified version of Linux which does not support IPSec.  So I try to get VMWare to manipulate IPSec for MyLinux.

  I used esxcli orders to successfully create configurations for IPSec between VMWare itself and other systems.

  However, I wonder if I can use the same esxcli commands to configure IPSec between MyLinux and other systems?  In my tests, VMWare does not perform tunneling IPSec data between the running machines and other virtual systems.

  It is an illustration of the configuration I created for MyLinux in VMWare.  I also have a security policy that is not visible.

  Name Source address Destination address State SPI Mode Encryption Algorithm, integrity algorithm to life

  --------                              -------------------------------------      -------------------------------------  ------      -----     ---------     --------------------               -------------------           --------

  MyLinuxToExternalSA MyLINUX.IPv6.ADDRESS EXTERNAL. Mature IPv6.ADDRESS infinity 0 x 300 transport 3des-cbc hmac-sha2-256

  ExternalToMyLinuxSA EXTERNAL. IPv6.ADDRESS infinite mature MyLINUX.IPv6.ADDRESS of hmac-sha2-256 0 x 256 transport 3des-cbc

  When I captured a trace TCP ping between MyLinux and the external system, MyLinux never sent the IPSec packets. Everything was sent in the clear.  This suggests that VMWare does not apply the rule for MyLinux, but I would like to confirm.  Thank you.

  Kwabena

  When you configure IPSec on ESXi, you sécuriserez the VMkernel traffic, not the virtual machine... If you want to protect the traffic of the virtual machine, you will need to enable IPSec on guest operating system.

  Here is more information on IPSec on ESXi: VMware KB: IPv6 and IPsec configuration on vSphere ESX and ESXi 4.1, 5.x ESXi

• Patching VMware ESXi

  So, I recently discovered that my VMware ESXi running ESXi 5.5.0 version 1331820 build number (ESXi 5.5.0 GA). Now, I know that there are a few fixes that have been released, ESXi550-201410001 is the most recent, because as far as I know. It would be convenient to patch, also if this is the case, can I just go what version I am now, download the recent patch and install directly, or is there a few required required fixes before. Active and important virtual machines running on hosts that I would be "patching" it may be closed, but it would be really bad if the patch to cause problems for causing problems for VMS host.

  I'm new to this, as I have never "patched" before ESXi. I guess I can use this (KB VMware: installation of patches on an ESXi host from the command-line 5.x ) as the documentation on how to install those.

  Thanks in advance!

  Yes, the ESXi patches are cumulative.

  Please read this blog post from VMware:are cumulative patches ESXi | VMware vSphere Blog - VMware Blogs

  Another good blog post about it:VMware experience before: are some cumulative patches 5.x ESXi?