VMware recommended best practices timing

Similar Questions

• upgrade vmware tools best practices

  What is the best practice to update vmware tools?

  It is advisable to check this?

  also use Update Manager?

  What is the difference if I do through the Manager Update vs pick and select all vms and update tools?

  This document... Yes, it should...

  VMware vSphere 5.1

• VMware View best practice checklist

  Hello

  I intend to POC to vmware view the customer with 200 clients. This is my first project for VDI.

  Someone at - it basis POC and list of best practices to ensure the customer have the right architecture, user profiles, policies, etc. ?

  Any suggestion?

  Kind regards

  Hudan

  If you or your company have access to PartnerConnect, there are some excellent documents out there that will give you everything you need for the deployment of a POC to the poster

• Parameters of database ORACLE 11g (Datawarehouse) - recommended/best practices

  Hi all
  
  What are the generally recommended database of parameters for one implementation of datawarehouse VLDB regarding:
  
  -The online Redo file size
  -Number of redo log file

  Do not explicitly set the log_buffer. Let Oracle autosize, it inspires the SGA_MAX_SIZE / SGA_TARGET.

  Hemant K Collette

• 10 GB NIC redundancy-Best Practice

  Hi all

  I have now deployed successfully to the 5 different poles of vSphere using 4 x 1 GB network adapters on all servers to ESX/ESXi hosts. I used 2 active/passive NIC in vSwitch0 vMotion and network management traffic (or Service Console for ESX) and used 2 active/active NIC in vSwitch1 for VM traffic as shown below. The uplinks are using 802. 1 q trunks in redundant Cisco switches.

  We are now moving to 10 GB networks. I have the opportunity to use this same design of map NETWORK 4 (using the HP Flex 10 vNIC or cards Cisco Palo) or go with a simpler model of map NETWORK 2. What is the recommended best practice to separate VMkernel Port and port VM group traffic among the physical network interface cards? Any suggestions or links to published documents would be greatly appreciated of VMware.

  Thank you!

  

  Take a look at my post here.  https://www.myciscocommunity.com/message/63033#63033

  Can help you with your design questions.  There is also a generic 'best practice' guide for 10G networks & VMware environments.

  As Cisco I obviously partial to the Palo adapter.  Unlike the Flex-10 option you set up not a bandwidth 'max' virtual NETWORK card, rather, you set a guarantee min. for each virtual host NIC given that you can create multiple network cards virtual with Palo, you can create one for VMotion, VM data, IP storage, etc. and define your QoS guarantees quickly & easily while offering redundancy with the recovery of host-transparent fabric.

  Let us know if you have specific questions about a deployment.

  Kind regards

  Robert

• Computer configuration virtual for SRM - files from memory Swap file/Virtual - best practice replication?

  Hello, I am very new to the model DR VMWare and have a few persistent questinos.

  What is the recommended best practice re: virtual computers invited windows and virtual memory files.  I think it would be unnecessary to replicate these changing data on the DR site.  I have several virtual machines with 6-8gig memory and I'm just wondering how can I isolate the ESX memory swap files and virtual memory in Windows feedback, so they get not replicated on the Dr site as often as changing os/data.  If it's even necessary to replicate.

  We use vspere vcenter 4.1 related modes, RS 4.1 the two on-site Cellera NX4 ReplicatorV2.

  I wonder if I can install the files of pages to be in a condition NOT replicated file system or a file system which is the only value replicates every 24 hours, or once a week.

  My reasoning here is.  Once the file is there, the operating system really cares about the changes in this file and dumps windows virtual memory on a restart, as well as the .vswp file.

  what I mean is built on a virtual disk full and placing the windows file on this virtual disk to Exchange.  This virtual disk could exist in a data store hosted on a celerra file system that does not get repeated as frequently as data/OS file systems.

  or am I completely off base here.

  I think that if you tried to reproduce these files and maintain a sync time minute 10, you would need a ton of bandwidth.

  any suggestions or recommendations or even pointers to Articles/items worth points = D.

  Thanks for your time.

  Given that the configuration is made at the level of the cluster and has no impact on the SRM, replication is not a factor.  Don't forget, not to replicate the LUNS with the swap, just files have a LUN configuration on the side of recovery as well and have this defined cluster Exchange files.  Also, on the virtual machine critical we define reservations memory so the pagefile is not a factor at all.

  Kind regards...

  Jamie

  If you found this information useful, please consider awarding points to 'Correct' or 'useful '.

  Remember, if it isn't one thing, it's your mother...

• vCenter/vSphere best practices documents or links

  Hi all

  I'll do some work on a client site next month. It seems to me that there are many things we can do in for vSphere vCenter.

  Y at - he of the docs of best practices or the links for vSphere?

  Thank you

  Here is a blog with lots of links to the best practices of VMware: VMware vSphere best practices - VMwaremine - Artur Krzywdzinski | Nutanix

  If you want something more specific, let me know.

• Best practices for migrating workflows, actions, patterns between environments

  Hello

  Is there a better document practical to migrate workflows, actions and configuration between vco (-> production development) environments. We want to lock all the workflows/action/configurations in prod. Migration can be done manually through package. Is there something more than that.

  Thank you

  Create a Package using Orchestrator (change the drop-down list in the client in CREATING packages of access mode).

  Add the desired workflow, actions, resources and Configurations to the package. As they added, dependent actions, workflows, resources and configuration items will be detected and added to the package.

  Right-click on the package and either export or synchronize.

  Backup file system export package / archive. Then import it on the server (test or production) target.

  Synchronize to test or prod server when you are ready.

  In both cases, you will be presented with a comparison window that indicates what workflow / actions/configurations/resources will be updated on the target system.

  Make an element by element synchronize would be tedious and could miss dependencies packages are the preferred and recommended best practice.

  For additional info of workflow development lifecycle, see blog of Christophe here: http://bit.ly/vroWdlc

• Dell MD3620i connect to vmware - best practices

  Hello community,

  I bought a Dell MD3620i with 2 x ports Ethernet 10Gbase-T on each controller (2 x controllers).
  My vmware environment consists of 2 x ESXi hosts (each with 2ports x 1Gbase-T) and a HP Lefthand (also 1Gbase-T) storage. The switches I have are the Cisco3750 who have only 1Gbase-T Ethernet.
  I'll replace this HP storage with DELL storage.
  As I have never worked with stores of DELL, I need your help in answering my questions:

  1. What is the best practices to connect to vmware at the Dell MD3620i hosts?
  2. What is the process to create a LUN?
  3. can I create more LUNS on a single disk group? or is the best practice to create a LUN on a group?
  4. how to configure iSCSI 10GBase-T working on the 1 Gbit/s switch ports?
  5 is the best practice to connect the Dell MD3620i directly to vmware without switch hosts?
  6. the old iscsi on HP storage is in another network, I can do vmotion to move all the VMS in an iSCSI network to another, and then change the IP addresses iSCSI on vmware virtual machines uninterrupted hosts?
  7. can I combine the two iSCSI ports to an interface of 2 Gbps to conenct to the switch? I use two switches, so I want to connect each controller to each switch limit their interfaces to 2 Gbps. My Question is, would be controller switched to another controller if the Ethernet link is located on the switch? (in which case a single reboot switch)

  Tahnks in advanse!

  Basics of TCP/IP: a computer cannot connect to 2 different networks (isolated) (e.g. 2 directly attached the cables between the server and an iSCSI port SAN) who share the same subnet.

  The corruption of data is very likely if you share the same vlan for iSCSI, however, performance and overall reliability would be affected.

  With a MD3620i, here are some configuration scenarios using the factory default subnets (and for DAS configurations I have added 4 additional subnets):

  Single switch (not recommended because the switch becomes your single point of failure):

  Controller 0:

  iSCSI port 0: 192.168.130.101

  iSCSI port 1: 192.168.131.101

  iSCSI port 2: 192.168.132.101

  iSCSI port 4: 192.168.133.101

  Controller 1:

  iSCSI port 0: 192.168.130.102

  iSCSI port 1: 192.168.131.102

  iSCSI port 2: 192.168.132.102

  iSCSI port 4: 192.168.133.102

  Server 1:

  iSCSI NIC 0: 192.168.130.110

  iSCSI NIC 1: 192.168.131.110

  iSCSI NIC 2: 192.168.132.110

  iSCSI NIC 3: 192.168.133.110

  Server 2:

  All ports plug 1 switch (obviously).

  If you only want to use the 2 NICs for iSCSI, have new server 1 Server subnet 130 and 131 and the use of the server 2 132 and 133, 3 then uses 130 and 131. This distributes the load of the e/s between the ports of iSCSI on the SAN.

  Two switches (a VLAN for all iSCSI ports on this switch if):

  NOTE: Do NOT link switches together. This avoids problems that occur on a switch does not affect the other switch.

  Controller 0:

  iSCSI port 0: 192.168.130.101-> for switch 1

  iSCSI port 1: 192.168.131.101-> to switch 2

  iSCSI port 2: 192.168.132.101-> for switch 1

  iSCSI port 4: 192.168.133.101-> to switch 2

  Controller 1:

  iSCSI port 0: 192.168.130.102-> for switch 1

  iSCSI port 1: 192.168.131.102-> to switch 2

  iSCSI port 2: 192.168.132.102-> for switch 1

  iSCSI port 4: 192.168.133.102-> to switch 2

  Server 1:

  iSCSI NIC 0: 192.168.130.110-> for switch 1

  iSCSI NIC 1: 192.168.131.110-> to switch 2

  iSCSI NIC 2: 192.168.132.110-> for switch 1

  iSCSI NIC 3: 192.168.133.110-> to switch 2

  Server 2:

  Same note on the use of only 2 cards per server for iSCSI. In this configuration each server will always use two switches so that a failure of the switch should not take down your server iSCSI connectivity.

  Quad switches (or 2 VLAN on each of the 2 switches above):

  iSCSI port 0: 192.168.130.101-> for switch 1

  iSCSI port 1: 192.168.131.101-> to switch 2

  iSCSI port 2: 192.168.132.101-> switch 3

  iSCSI port 4: 192.168.133.101-> at 4 switch

  Controller 1:

  iSCSI port 0: 192.168.130.102-> for switch 1

  iSCSI port 1: 192.168.131.102-> to switch 2

  iSCSI port 2: 192.168.132.102-> switch 3

  iSCSI port 4: 192.168.133.102-> at 4 switch

  Server 1:

  iSCSI NIC 0: 192.168.130.110-> for switch 1

  iSCSI NIC 1: 192.168.131.110-> to switch 2

  iSCSI NIC 2: 192.168.132.110-> switch 3

  iSCSI NIC 3: 192.168.133.110-> at 4 switch

  Server 2:

  In this case using 2 NICs per server is the first server uses the first 2 switches and the second server uses the second series of switches.

  Join directly:

  iSCSI port 0: 192.168.130.101-> server iSCSI NIC 1 (on an example of 192.168.130.110 IP)

  iSCSI port 1: 192.168.131.101-> server iSCSI NIC 2 (on an example of 192.168.131.110 IP)

  iSCSI port 2: 192.168.132.101-> server iSCSI NIC 3 (on an example of 192.168.132.110 IP)

  iSCSI port 4: 192.168.133.101-> server iSCSI NIC 4 (on an example of 192.168.133.110 IP)

  Controller 1:

  iSCSI port 0: 192.168.134.102-> server iSCSI NIC 5 (on an example of 192.168.134.110 IP)

  iSCSI port 1: 192.168.135.102-> server iSCSI NIC 6 (on an example of 192.168.135.110 IP)

  iSCSI port 2: 192.168.136.102-> server iSCSI NIC 7 (on an example of 192.168.136.110 IP)

  iSCSI port 4: 192.168.137.102-> server iSCSI NIC 8 (on an example of 192.168.137.110 IP)

  I left just 4 subnets controller 1 on the '102' IPs for more easy changing future.

• Recommendations or best practices configuration Oracle HTTP Server Oracle Webcenter 11g Portal

  Hello everyone.

  I'm looking for recommendations or best practices configuration Oracle HTTP Server Oracle Webcenter 11 g Portal

  I appreciate if you could give me some references and/or experiences.

  Thank you very much in advance.

  Best regards.

  Configurations may vary depends on place on your needs, in general you can see Configuration high availability for the Web - 11 g Release 1 (11.1.1) layer components

  Use the configuration WebTier documents to the address above if it is sufficient for your needs.

• What is the best practice for a 'regular' Server VMware and VDI environment?

  What is the best practice for a "regular" VMware Server and VDI environment?   A single environment (ESXi and SAN) can accommodate two if it is a whole new configuration?  Or even better to keep separate?

  Enjoying inputs.

  Quick and dirty answer is that "it depends."

  serioulsy, it depends really two things budget and IO.  If you had the money for two without then buy two and don't have to host your server environment and the other for VDI desktop, their IO profiles are completely different.

  If this is not the case, try to keep each type of use for their own dedicated LUN.

• What is the best practice to merge both vMware vSphere environments?

  We recently bought another company that also manages vMware 4.

  They have a 4-node cluster and we have a 3 a node. Each is managed by its own vcentre.

  What would be the best practice to migrate all the guests and the hosts on the server main vCentre.

  Thank you

  Lance

  I choose one of the vCenters, unplug and remove hosts from the other and connect them to those elected. Configure the cluster after that (all in the same or keep the separation of the group, which I think is the best)

  You can also use related modes.

  Marcelo Soares

  VMWare Certified Professional 310/410

  Master virtualization technology

  Globant Argentina

  Review the allocation of points for "useful" or "right" answers.

• Recommendations or best practices around change of the audio data on a network share?

  I have several users editing audio located on the same network share. They are always complaining about the performance.  Is it a best practice to edit audio located on the network?  I see so many issues (latency time, possible corruption, etc.) with that from the computer SCIENCE point of view, but I would like the opinion of those more familiar with the application and its best practices.  Thanks in advance.

  It's crazy! So that any audio to be edited with any degree of speed and security, it must be downloaded to a local computer, edited on that, and then the final result re-recorded on the network.

  You might as well do this anyway - at the time wherever you make a change, you store a local version of the file temp on the editing machine, and it has real save, or save as who turned to the network drive. Also, you would be working on a copy, the original is still available in the case of the vis - is up, and would not be the case if you edit the original files directly on the network, so it is intrinsically safer.

• Best Practice Guide for stacked N3024 switches

  Is there a guide to BP for the configuration of the 2 N3024s stacked for the connections to the server, or is the same eql iscsi configuration guide.

  I'm trying to:

  1) reduce to a single point of failure for rack.

  (2) make good use of LACP for 2 and 4 nic server connections

  (3) use a 5224 with it's 1 lacp-> n3024s for devices of unique connection point (ie: internet router)

  TIA

  Jim...

  Barrett pointed out many of the common practices suggested for stacking. The best practice is to use a loop for stacking and distributing your LAG on multiple switches in the stack, are not specific to any brand or model of the switch. The steps described in the guides of the user or the white papers generally what is the recommended configuration.
  http://Dell.to/20sLnnc

  Many of the best practices scenarios will change of network-to-network based around what is currently plugged into the switch, and the independent networks needs / requirements of business. This has created a scenario where the default settings on a switch are pre-programmed for what is optimal for a fresh switch. Then recommended are described in detail in white papers for specific and not centralized scenarios in a single document of best practices that attempts to cover all scenarios.

  Express.ypH N-series switches are:
  -RSTP is enabled by default.
  -Green eee-mode is disabled by default.
  -Frother is enabled by default.
  -Storm control is disabled by default.

  Then these things can change based on the towed gear and needs/desires of the whole of society.

  For example, Equallogic has several guides that recommendations of configuration detail to different switches.
  http://Dell.to/1ICQhFX

  Then on the side server, you would like to look more like the OS/server role. For example a whitepaper VMware that has some network settings proposed when running VMware in an iSCSI environment.
  http://bit.LY/2ach2I7

  I suggest making a list of the technology/hardware/software, which is used on the network. Then use this list to acquire white papers for specific areas. Then use these white papers best practices in order to ensure the switch configuration is optimal for the task required by the network.

• Best practices for the configuration of virtual drive on NGC

  Hello

  I have two C210 M2 Server with 6G of LSI MegaRAID 9261-8i card with 10 each 135 GB HDDs. When I tried the automatic selection of the RAID configuration, the system has created a virtual disk with RAID 6. My concern is that the best practice is to configure the virtual drive? Is - RAID 1 and RAID5 or all in a single drive with RAID6? Any help will be appreciated.

  Thank you.

  Since you've decided to have the CPU on the server apps, voice applications have specified their recommendations here.

  http://docwiki.Cisco.com/wiki/Tested_Reference_Configurations_%28TRC%29

  I think that your server C210 specifications might be corresponding TRC #1, where you need to have

  RAID 1 - first two drives for VMware

  RAID 5 - 8 hard drives within the data store for virtual machines (CUCM and CUC)

  HTH

  Padma