VMware® Workstation 8.0.4 you will only be able to run 32-bit nested vMs

Similar Questions

• NO MESSAGE SERVICES CONFIGURES blackBerry smartphones. YOU WILL ONLY BE ABLE TO SAVE AS A DRAFT

  BOLD 9700, T-Mobile.  I have the current operating system.  I get the above message when I try to reply to an email.  Yesterday - I had no such problem.  I'm going to E-mail set up & my email addresses are here.  When I'm in the message options and choose settings Email - there is NOTHING there.  Any suggestions?

  Go to the icon manage Internet Email on your device.  Press the menu k ey and select "Service books".  Then select "send Service books".

• Cannot use disk, error: Disc Copier could not find a CD-ROM drive supported. You will not be able to make copies of the disc to another.

  Original title: follow question Winsows XP repair

  I get following messages is displayed when I try to use disk functions.  #1 API can not see all CD ROMS in the system, please check to see if they are properly plugged...

  #2 disc copy could not find a CD-ROM drive supported.  You will not be able to make copies of the disc to another.

  Should I take the modem to a computer repair shop to get this repaired?

  Hello

  I suggest to refer to the procedure described in the following article and check the status of the issue.

  Error messages occur when you run Easy CD Creator in Windows XP.

  http://support.Microsoft.com/kb/285910

• The document _ is on a volume that does not support the permanent version storage.  You will not be able to access older versions of this document once you close.

  I recently started getting this strange message, usually when a Pages document is closed:

  «The document _ is on a volume that does not support the permanent version storage.»  You can access older versions of this document once you close. »

  All my research (apple.com and on the internet) have not enabled all the information on this message.

  Hi Larry,

  The 'volume' is a hard disk, a partition on a hard drive or a storage as a USB device.

  OS X automatically saves your document frequent while you work on it. If the volume of the device / it records on a summer formatted to allow 'versioning', you will be able to use Time Machine to open previous versions of your document. If it has not been formatted like that, you get the message see you, and only the current version of the document will be saved.

  Kind regards

  Barry

• PlayReady update was Incomplete.You will not be able to watch or record content protected until the is qualified. Everyone I have this same problem and found a solution?

  I clean installed 2 x times the RC of windows 7 pro x 64. Both times I got this error in media center. I manually downloaded the playready 1.3 program. I can record my channels satalite with no problems so I don't understand why he repeats the above message. However, I am worried that when the DRM updates for the satalite it won't work and I won't be able to update. I have not changed anything in the hardware level in the computer as so he wouldn't because he thinks it's another computer. Any help would be appreciated.

  Clarification on this: summer working on this issue for more than 2 months on 4 computers, that's what I found.

  Note: Not all the patches will work on a pc due to various stages of updates, patches, etc. No matter what anyone says or claims. What works for me, the other person or even technical support, may not be due to a strange configuration on your pc. Nevertheless, that's what I did on the final 3 computers that have no auto update of the readyplay.

  (1) get to the point in media center it says Readyplay failed to update, you want to try again.

  (OPTIONAL) Download the tool from Microsoft DRM Reset, change in Compatibility Mode for Windows 7 (or any version of Windows), run the tool as admin. He must install and say successful.

  (2) open Windows "Services" via the control panel > administrative tools > Services.

  (3) with Media Center open and show "the PlayReady update was incomplete. Do you want to retry? "Goto Control Panel"Services"you just opened and scroll all the way" Services Windows Media Center Receiver ", double-click it, and then click on"Stop ".

  4) navigate to the folder ReadyPlay HIDDEN (C:\ProgramData\Microsoft\PlayReady), and THEN Delete the mspr.hds file.

  (5) return to the OPEN & CONTINUES, Media Center and click 'Yes' and 'Next' to the question of the PlayReady update. He should immediately zip past and say update complete & you can watch and record copy-protected blah blah blah. It can also update a guide or something too.

  If this doesn't work for you after that 5-6 tests, you have something to another block you, but you don't have need for both 32 bit and 64 bit PlayReady installed to update. This is the 'Service' which is really prevents the update, but simply stop w/o those other steps do not work >.

  Good luck!

• You will still be able to use the old CS licenses if you subscribe to creative cloud with discount customers CS?

  I bought CS4 in 09, and he says he has a subscription rate of discount for customers of cs. If I am subscribed to this plan, I would be able to use my 2 licenses of CS4, as well as 2 CC licenses? I have several computers at home. Thank you.

  Hello

  Please see > http://helpx.adobe.com/creative-cloud/help/install-apps.html here > how many computers can I install on

  I quote: you can install the software on two computers. These two computers can be Windows, Mac OS, or everyone.

  If you install on a third computer, you will be asked to turn off this feature on the other two computers. You can then re-enable one of the two previous computers and use Cloud Creative apps on it.

  With regards to your CS4, which is not a problem to use further, as I do with my Adobe Web premium CS4.

  Hans-Günter

• My WiFi will only connect if I run the convenience store that corrects the problem, and then I'm ok

  My settings are set to auto connect, but lately it does not connect automatically. It is said to run the troubleshooter.  I start the game of shooting and it solves the problem and I am running. My problem is that I have to do this every time I open my laptop.

  Hi Mike,.

  Thanks for posting your query in the Microsoft Community Forums.

  After the description of the question, I understand that you have problems with wifi on the Windows 7 computer connections.

  I understand this must be frustrating, but don't worry, we're here to help and guide you in the right direction.

  I suggest you to update the network driver and check if it helps. See step 4 of section for help to update the drivers.

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  It will be useful.

  Let us know if you encounter problems with Windows in the future. We will be happy to help you

• When I open any pdf file I get the following message: FAILURE of FILEOPENINITIALIZATION (1): you will not be able to open protected documents

  does anyone know how to fix this?

  FIleOpen is an add-on for Adobe Reader, used to read protected documents special. It's not made by Adobe. You can visit http://www.fileopen.com/ for info.

• 64 bit VMs in ESX/ESXi 4.0 that is running as a Virtual Machine in VMware Workstation 7.0.1

  I created an ESX4 host in VMware Workstation 7.0.1 as a Machine with 4 GB of RAM, 2 vCPUs and 1 (25 GB for installation) VMDK virtual and more later added 75 GB VMDK as an iSCSI LUN using openfiler.

  My vCenter Server runs as a Virtual Machine with SQL Express Edition 2005 DB.

  I want to install a Windows Server 2008 R2, which is a 64-bit as a virtual machine within the VM ESX4 embedded operating system. Is this possible?

  Hello

  as this comment by DOC from VMWare, in the 'internal' invited you will just be able to run 32-bit clients, never a 64 bit one.

  Best wishes / Saludos.

  Pablo

  Please consider to assign all useful or correct answer. Thank you!! - Por favor considered premiar any respuesta correcta o util. ¡¡MUCHAS gracias!

  Virtually noob blog

• Impossible to run/load 64 - bit OS in VMware Workstation 8

  I recently bought VMware Workstation 8.  It is installed on a laptop Lenovo T510 with 8 gigabytes of memory, Intel Virtualization is enabled in the BIOS.  I am running Windows 7 64-bit with all the service packs and hotfixes installed from this announcement on March 13, 2012.  My processor is a Mobile Core i7 620 m.

  I'm trying to load a 64-bit operating system, I'm able to succeed in creating the virtual machine.  However when I try to load the 64-bit operating system, I get the following message is displayed:

  Virtualization host is disabled in the BIOS/Firmware of host.

  With the help of virtualization with MMU software software.

  The above message is incorrect; I have virtualization enabled in BIOS.   I checked several times.

  Also, I get a window appears that displays the following text:

  Software virtualization is incompatible with the long mode on this platform.  Long mode off.  Without the support of the long mode, the virtual machine will not be able to run 64-bit code.  For more details, see: http://vmware.com/info?id=152.

  Please help me with this problem.

  Thank you

  Lou

  I have the same problem with VMware Workstation 8 and I tried the method of vMLH thus, still encounter the same error message (I created a new guest OS and made all settings before starting from 1).

  (I'm using a Thinkpad x201t with processor: Intel Core i7 L 620 2.00 GHz)

• VmWare Workstation 8 and no 64-bit support

  First of all. I'm sorry for my bad English.

  My hardware:

  ASUS Sabertooth X 58 Mainboard

  Intel Core i7 950 CPU

  12 GB of Ram

  Under a Windows 7 Ultimate (latest patches installed)

  In the Bios is VT ENABELT

  My problem is that since a little day invited VMware Server as me as my PC dosnt support 64-Bit operating system.

  Follow them Info box introduce yourself a way:

  Virtualization software is Incompatible with the long Mode on this platform, the virtual machine will not be able to run 64-bit code.

  So I have a w2k8 R2 on my server and it runns fine until the error message.

  I hope you can help me quickly while im doing certificate MCITP training and Certification tests in 4 weeks and I neet training

  Thanks a lot for your help.

  Sorry if I post in the wrong Thread.

  There are a few days ago a user had problems with 64-bit VM too well that VT has been activated. Perhaps the cause (and the resolution/workaround) are the same.

  According to Re: comments 8 and 64-bit Workstation bits in the vmware.log indicate that VT - x is turned on.

  2011 09-23 T 23: 21:35.610 + 02:00 | VMX | I120: Common: MSR 0x3a = 0x5

  Bit 0 and bit 2 are defined.

  So maybe jmattson workaround provided in the mentioned discussion can help.

  Add the following line to C:\ProgramData\VMware\VMware Workstation\config.ini:

  hv.assumeEnabled = TRUE
  

  André

• How to set an MTU of 1600 for test Lab at home for the NSX on Vmware workstation

  Hello.

  I'll set up a laboratory at home to build a laboratory to the NSX. I am running 3 on VMware Workstation 11 Esxi hosts. All three hosts of esxi run each 4 Ethernet adapters on them.

  To configure installation VXlan for my lab at home, I have modified the virtual machine's .vmx file and changed the vmxnet3 device and it works.

  Ethernet1. ConnectionType = "custom".

  Ethernet1.virtualDev = "e1000".

  Ethernet1.wakeOnPcktRcv = "FALSE".

  Ethernet1. AddressType = 'generated '.

  ethernet2. Present = 'TRUE '.

  ethernet2.VNET = "VMnet1.

  ethernet2. ConnectionType = "custom".

  ethernet2.virtualDev = "vmxnet3" - change to vmxnet3

  Adapter type VMxnet3 only is not supported for VMware workstation and also one of my hosts broke down several times with the low error message in the log file.

  2015-08 - 02T 13: 37:48.254 + 10:00 | vCPU-4 | I120: Ethernet3 MAC address: 00: 0C: d 29:a4:7: 8 c

  2015-08 - 02T 13: 37:48.261 + 10:00 | vCPU-4 | I120: VMXNET3 user: Ethernet3 pilot Info: version = 16908544 gosBits = 2 gosType = 1, gosVer = 0, gosMisc = 0

  2015-08 - 02T 13: 37:48.527 + 10:00 | vCPU-5 | I120: VMXNET3 hosted: Packet has no eop, 1 scanner, tx ring size 512, txd valid 0.

  2015-08 - 02T 13: 37:48.527 + 10:00 | vCPU-4 | I120: Ethernet3 MAC address: 00: 0C: d 29:a4:7: 8 c

  2015-08 - 02T 13: 37:48.536 + 10:00 | vCPU-4 | I120: VMXNET3 user: Ethernet3 pilot Info: version = 16908544 gosBits = 2 gosType = 1, gosVer = 0, gosMisc = 0

  2015-08 - 02T 13: 37:51.436 + 10:00 | VMX | I120: E1000: E1000 full rx ring, empty packages.

  2015-08 - 02T 13: 37:53.636 + 10:00 | MKS | I120: MKS - SWB: number of MKSWindows has changed: 1 make MKSWindow (s) total 2.

  2015-08 - 02T 13: 37:55.565 + 10:00 | VMX | I120: VMXVmdbCbVmVmxExecState: change of State Exec asked State poweredOff without reset, soft, softOptionTimeout: 20000000.

  2015-08 - 02T 13: 37:55.565 + 10:00 | VMX | I120: Stopping VCPU son...

  2015-08 - 02T 13: 37:56.567 + 10:00 | SVGA | I120: Fate of thread SVGA

  2015-08 - 02T 13: 37:56.571 + 10:00 | MKS | I120: MKS - SWB: number of MKSWindows changed: 0 record (s) MKSWindow of total 1.

  2015-08 - 02T 13: 37:56.575 + 10:00 | MKS | I120: GDI-Backend: HWinMux stopped making the composition of the window.

  2015-08 - 02T 13: 37:56.575 + 10:00 | MKS | I120: MKS - SWB: number of MKSWindows changed: 0 record (s) MKSWindow of total 0.

  2015-08 - 02T 13: 37:56.575 + 10:00 | VMX | I120: Thread MKS is stopped

  Can someone guide me how to set up a lab NSX on VMware workstation and use 1600 MTU for VXlan traffic. Any help is very appreciated.

  Hi all

  I managed to solve this problem by separating the storage traffic to a different vswitch and the traffic to a different VDS NSX.

  ~ # esxcfg - NICS - l

  Name PCI Driver link speed Duplex MAC address MTU Description

  vmnic0 e1000 up to 1000Mbps Full 00 0000:02:01.00: 0C: d 29:a4:7: Intel Corporation 1500 6th 82545EM controller Gigabit Ethernet (copper)

  vmnic1 e1000 up to 1000Mbps Full 00 0000:02:04.00: 0C: 29:a4:7 d: 78 1500 Corporation Intel 82545EM Gigabit Ethernet Controller (copper)

  vmnic2 e1000 up to 1000Mbps Full 00 0000:02:05.00: 0C: 29:a4:7 d: 82 1600 Corporation Intel 82545EM Gigabit Ethernet Controller (copper)

  vmnic3 0000: 0b: 00.00 vmxnet3 Up Full 00 10000Mbps: 0C: 29:a4:7 d: 8 c 1600 vmxnet3 Inc. VMware Virtual Ethernet Controller.

  ~ # esxcfg - vswitch - l

  Switch name Num used Ports configured Ports MTU rising ports

  1536 5 128 1500 vmnic0 vSwitch0

  Name PortGroup VLAN ID used rising Ports

  The VM network 0 0 vmnic0

  0 1 vmnic0 VMkernel

  0 1 vmnic0 network management

  DVS name Num used Ports Ports Ports configured MTU rising

  dvSwitch 1536 10 512 1600 vmnic3 - for network traffic

  DVPort use customer ID

  7 1 vmnic3

  81 1 NSX 2 controller nsx_controller_4be65643-37ca-468e-b00a-f711d6cc5447.eth0---noeud

  79 1 nsx_controller_8bb60e33-b290-4252-92b1-501aa2f83607.eth0---noeud NSX Controller 3

  110 1 vmk2 - vtep interface for the host

  119 1 Linux1.eth0 - test Linux VM

  This laboratory works fine for me now and my Adviser for laboratory at home will be not to use the same network card for storage traffic that was used for the traffic of the NSX.

  Thank you for all your help.

• HELP me please, could not return to vm and crash of vmware workstation 7

  Help!

  I'm in deep problem with a virtual machine that does not work either... I'm disparate because I can't go to a previous snapshot.

  I have a machine t1500 dell with core i870, 16 GB of ram, nvidia quadro fx 512 mb graphics card, 500 gb hd, windows 7 pro 64-bit.

  In this machine wmware workstation 7 (latest version) is installed with autoprotect runs up to 10 daily snapshot.

  About 40 days, I converted two computers in vm... one with 32-bit vista and one with 32-bit xp.

  Every month the recent, everything works well... but yesterday all the vm was crushed because the space in my hd was full... so since the Snapshot Manager, I deleted some old snapshot.

  During the removal of a few shots, sometimes it shows me that he can't remove because the disc is always busy... but, but icon in the timeline of the Snapshot Manager went... go in the folder where I saved the files in vm, also failed in the Recycle Bin of windows.

  Once deleted, I try to turn it on again the vista 32 bit vm... aaaaahhhhhh, it does not start! and it remains pending mode... why!... If I try to take it back, all wmware workstation crash and I can only see a windows message error that vmware workstation has stopped working.

  Then I try to run the virtual machine with 32-bit xp and it work without any problem.

  Then I opened again snapshot manager and I try to use the function "go to...". "to recover a snapshot... ahhhhhh! nothing to do! It crash again!

  so I tried also to remove some files as described in this Ko... but not at all, it crash again!

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 1003846

  HELP ME, PLEASE! I have all my projects in this machine is very important... If I lose the...

  OK, so it looks like us (you) lost snapshot sw2 - 000010.vmdk, which was created between March 1 and March 2.

  What we need to do now is to repair the broken chain instant (because of the missing original sw2 - 000010.vmdk) and create a clone of this disc. Snapshots 000043 and 000044 contain no data and can be ignored.

  What we need to do is:

  1.) to repair the chain instant (link sw2 - 000009.vmdk to sw2 - 000006.vmdk)

  • SW2 - 000009.vmdk backup since we need to modify this file
  • Copy the sw2 - 000009.txt attached to the virtual machine file
  • Copy dsfi.exe to the virtual computers folder
  • run: 'sw2 - 000009.vmdk' dsfi.exe 512 800 'sw2 - 000009.txt.

  2.) creating a clone

  • find a drive with enough free space on the drive on which the clone will be created!
  • run: "C:\Program Files (x 86) \VMware\VMware Workstation\vmware - vdiskmanager.exe «r - t 0 \sw2clone.vmdk C:\vm\sw2\sw2-000042.vmdk»»
  • Create a new virtual machine and attach the vmdk cloned (using existing disk) instead of creating a new disc
  • Before you start the virtual machine, create a snapshot where the clone has some corrupted data and you must go back to for example to fix this virtual disk to a helper VM or open it with the disk mounter utility.
  • run the chkdsk command to check that the disc is ok

  André

• Can we run a 64 bit os on a server esx guest in vmware workstation?

  Hello

  Can we run os 64-bit on an esx server that running as a guest in vmware workstation?

  Thank you

  lol you can run 32-bit nested VM, but not 64-bit

  http://communities.VMware.com/docs/doc-8970

  VMWare products as guest hypervisors

  Since the products current VMWare does not virtualize the virtualization features assisted by the physical processor hardware (or controls segment limit of 64-bit AMD processors), you will be limited to the execution of 32-bit only nested If you use a binary translation under ESX as the guest

  hypervisor.

• How to move the Virtual Machine VMWare Workstation 10 to a completely different computer

  I have a laptop that is going to become my 'old' laptop, I bought and am always set up a new computer.

  I have a VM THAT evolution created on the 'old' portable using VMWare Workstation 10.  I installed the software VMWare Workstation 10 on the new laptop computer and am ready to move to the existing VM development since the old laptop again to continue the development of software on the virtual machine to the new machine.

  I never moved a computer virtual from one computer to another, and I guess that all I have to do is to copy and move the folder and all its content from the old laptop to the new, and then I'll be back in business?

  Just make sure it is this simple before doing so.

  Thanks for any input.

  It's as simple as that. When you start in the new machine, it should ask if you copied or moved. Answer that you moved it will keep the same MAC address and you will not be able to connect the two copies at the same time. You copied it saying assigns a new MAC and they both can connect, but a Windows machine can ask to reactivate. Seems to me he asked also to reactivate when I copied it for an Intel system AMD system, but it was a long time ago

  Lou