VPNClient connects, but fail links network

Similar Questions

• VPN connected but no visible network

  so I have a windows 7 (VPN server) desktop computer and a windows laptop 7 (VPN client) and I have set up the incoming VPN connection on my desktop and a client VPN connection on my laptop. When I go and establish a VPN connection, it says that I'm connected on my laptop and my desktop but I can't access my network resources. Ive been cracking as a result for a few weeks now and have gotten nowhere with it, any help would be greatly appreciated. Thank you!

  I can't access something like \\ServerName\ShareName I can't do a ping them either. address ranges are not the same on the server or client networks. the funny this is that it says I am connected at both ends, the customer declares that ipv4 has no internet access on the vpn which is fine because all I want is access to the network and it shows that I have an ip address assigned on the vpn map. side server but it is said that ipv4 and ipv6 are not connected, but if I do "ipconfig/all" he shows me his ip address on the vpn.

  client side, I've disabled 'Gateway on remote network use default' so that I can still have access to the internet on the im client that is connected to the vpn. on the side server, I tried selecting "Assign addresses automatically using DHCP" as well as "specify IP addresses (with a beach which is on the client and the server ip address range).» I have also "Allow the calling computer to specify its own IP address" selected on the server.

  When I finally fell a VPN server on a Vista box I got the address assigned to the configuration of clients like that.

  http://theillustratednetwork.MVPs.org/Vista/PPTP/VPNSetup06.jpg

  The address range was the same that the server of the LAN address range, in this case, I used 192.168.10.X on the local network.

  http://theillustratednetwork.MVPs.org/Vista/PPTP/ExampleVistaVPNNetwork.PDF

  Customer recevrait.31 ou.32...

  Of course assumed that the customer was or would not be on a LAN 192.168.10.X to start. If it was so I could have problems connecting to shares on my LAN Server.

  MS - MVP Windows Desktop Experience
  "When all else fails try what the captain suggested before you started...". »

• readers of connection but the VPN network not showing

  I have a couple of Windows machines that work very well, so I certainly have the correct information for VPN.

  When I hit 'Connect', it does not seem to connect to the VPN with success and I can see the data traffic in both directions.

  After that, I tried "Go to server" and if I navigate or enter the details of the server manually, it will not connect to network server actions.

  I think I have the completely straight oblique lines around and I tried to add the username at the end of the address of the server, which is an SME.

  I put as follows

  SMB://server/folder/

  I also tried smb://server/folder/username

  No joy. Can anyone help please?

  Thank you

  Navigation uses Hello and Hello does not normally work through non-local connections, so it will not work on a VPN connection. It should be possible to connect through a VPN by using one of the following URL format in "connect to Server".

  AFP://192.168.1.10

  or

  AFP://fileserver.domain.com

  AFP://fileserver.local will not work since it is reserved for the Hello that as I mentioned does not work over remote links.

  Note: Not everyone gets their properly configured VPN system for searching DNS is possible that afp://fileserver.domain.com may also fail but the numeric address should work.

  Note: Again according to the VPN configuration, they may need to define a static route and have failed to do so, it would break digital even answer, however if numeric address works for Windows, they must work for Macs.

  It is always interesting to try to PING tests.

• Try to create a new VPN connection but Creat new network connection is grayed out

  Hello world

  Thank you for your help in advance.

  I would like to ask why I could not create a new VPN connection as the "Creat new network connection" is grayed out. I'm also sure that remote access connection manager, and another car once are started.

  I can create an account with my domain administrator account. But once I passed the orginary user, the shortcut to the connection could not be accessed. I also tried to add the user to the local Administrators group, and the result is the same.

  HOEP that you can help.

  Thank you.

  Windows XP Service Pack 3?

  Do you have any software security 3rd party running on this computer?  Or maybe something in group policy that limits access to create a new network connection?

  -B-
  http://www.officeforlawyers.com | http://www.OneNote-tips.com
  Author: Guide to counsel for Microsoft Outlook

• Cisco vpn 5.0.07.0440 - k9 connected but not the network remote access to Windows 8.1 pro

  I use 5.0.07.0440 - k9 vpn Cisco and Cisco vpn 5.0.07.0290 - k9 both version on our 8.1 Windows Mobile pro.
  VPN connected successfully, but not remote access network and receive no ping.

  But when I try with wifi and vpn, then good job.

  Please help me as soon as possible.

  Thank you
  Sanjib

  It is very problematic on Windows 8 and EOL now.

  Kind regards

  Nehmaan

• Link network LED on the blades of the UCS

  Hello

  We got a work system user guide (6248 FI, 5108 chassis with IOM blades and B200-M3 2204) everything works fine but the link network LEDS are off. Is this a normal behavior? Since then, according to the documentation, they should blink green.

  concerning

  Hey Lukasz,

  This is followed by default CSCul93683, as it is postponed to the next major release (2.2 (3), ETA No. yet), so that you can add to your list of bug track and monitoring of the air.

  Thank you

  Majid

• I am connected but centre network and sharing Center says im not. It shows no connection available, even if I am logged in? Photo included (win 7 pro64)

  Here is a link that shows the problem better than I can explain it.

  http://www.mediafire.com/i/?n3dy0y5qldyy3y7

  I am connected to the net via an ethernet cable and I have an internet connection, but I use my pc to share files with my laptop and xbox and now I can not because he thinks it is connected to a network and do not think that some are available. When I say to diagnose it fails to find a solution.

  I looked online but has not gotten anywhere. I uninstalled and reinstalled hardware drivers and I checked the network services are running.

  Your help is highly appreciated

  Paul

  Hello again Paul,

  Sorry for the late reply.
  Go through your list services.msc and click twice on the service of "knowledge of network locations.
  Stop the service and then restart and then check to see if she is still shows as not connected to any network.
  If that does nothing so this thread has some advanced troubleshooting which involves some registry settings and permissions that appear to have worked for a large number of users inside:
  http://social.technet.Microsoft.com/forums/en/w7itpronetworking/thread/df17c593-E78F-4878-97b0-7569307934c5
  If you are uncomfortable trying these changes then I suggest to try.

• Windows 7 recognizes a wireless network; trying to connect but can not

  My laptop with Windows 7 detect my home wifi network. I typed in the access code and my computer attempted to connect with him, but it still fails. I ran the store and followed all the steps, he gave me. I unplugged unit, waited 10 seconds, plugged it back in, and represented the resolution of problems, and it came with the message "Windows cannot solve your problem of wireless connectivity."

  How can I fix it? If necessary, I can provide more information in the troubleshooting report.

  Hi Mellodramatikk,

  -You receive an error message after you type in the access code?

  You can try to start your computer in safe mode with network and check if you can connect to the wireless network.

  . To boot to the desktop in safe mode with network keep tapping key F8 during restart. Once you see the option to start it in safe mode with select network and press ENTER.

  Access the link to learn more about how to start the computer in safe mode:http://windows.microsoft.com/en-US/windows7/Start-your-computer-in-safe-mode

  Also, check if you have any third party security installed on your computer and try to temporarily disable the security software of the computer and try to connect to the wireless network. If you are able to connect to the wireless network after you disable the security software, you can contact the manufacturer of security software and check if you need to change the settings. Later, re-enable the security software.

  Post back with the above information and let us know the result.

  Thank you and best regards,

  Srinivas R Microsoft technical support.

  Visit ourMicrosoft answers feedback Forum and let us know what you think.

• HP OfficeJet Pro 8600: HP OfficeJet Pro 8600, connected to the local network but does not print a printer on the same LAN

  HP OfficeJet Pro 8600, connected to the local network but cannot print printer on the same local network.

  Work tried fixing it but all attempts fail.

  Firewall disabled.

  Printer recognizes the router's LAN.

  Was also pointed out that the port does not communicate, can not remove it; Cannot add another...

  Printer does not print.

  How can I fix?

  Hi @AnnisMonadjem,

  Welcome to the Forums of HP Support!

  I understand that you are unable to print to your printer HP Officejet Pro 8600. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  When you say 'LAN', are you referring to the network or you try to share the printer on the network?

  How is the printer connected? (Ethernet/WiFi)

  If you have noticed that the port is causing problems, please download and run the print and Scan doctor, it will be probably diagnose and fix the problem you are experiencing.

  What were the results when you ran the Print and Scan Doctor? (she print or scan, error messages)

  HP has several Officejet Pro 8600 series.

  What is the name and the product number of your printer? How can I find my model number or product number?

  • Update the firmware of the printer.
  • Don't hide the SSID (network name).
  • What type of encryption are you helping? HP recommends WPA and WPA2.
  • You have a double router broadband? Make sure that the two groups were not the same network name.

  If the problem persists, you may encounter an IP address conflict. It's a good idea to assign the printer a static IP address outside your DHCP range. For example, some routers default DHCP is located between 192.168.0.100 to 192.168.0.200. So, I would use 192.168.0.232.

  To assign the static IP address, use the following steps as a guide.

  • Print a Page of Network Configuration menu of the printer front panel. Note the IP printer. IPV4 address
  • Type the IP address in the browser to bring up the SAP.
  • Choose the network tab, then wireless on the left side, and then select the IPv4 tab.
  • Select Manual IP.
  • Enter your IP address manual (192.168.0.232)
  • Enter 255.255.255.0 for the subnet mask, except if it is different.
  • Enter the IP address of your router that sits on the Network Configuration Page) for the default gateway.
  • Please, click on manual DNS server. For the preferred DNS Server Manual please enter 8.8.8.8 and the Alternate DNS Server Manual, please enter 8.8.4.4.
  • Click on apply.
  • Restart the router, the printer and the computer.
  • Test printing and scanning.

  If the problem persists, download and run this patch rollup: resolving printing issues in Windows 7 and Windows Server 2008 R2

  • Try printing and scanning.

  In addition, if you are still having problems try the steps in this guide, HP printers - "offline" Status Message printer (Windows 7).

  Continue on, if the problem persists.

  Important!   Delete the temporary files and folders by using the disk cleanup utility

  1. Open the disk cleanup utility:

• I am connected but the network properties window does not show the size of the packets to all the

  I am connected but the network properties window does not show the size of the packets to all the

  Hi asaimas,

  You can follow this link & check if it helps:

  Configure the Option of configuring server network packet size

  Hope the helps of information.

• I can not connect computer vista laptop to my network home, but I can connect to other networks. Other computers can connect to my home network very well. This can be corrected?

  My laptop runs Vista and I've not had problems connecting to my home network wireless until a week ago or not.  Then, trying to connect, I see other available networks, but not my own.  When I try to connect manually, it says that the network already exists.  Other computers, macbooks, are able to connect to my home network without problem.  I am able to connect to a network on my laptop fine unsecured wireless.

  I could 'solve' the problem or get reconnected with a restoration of the system to an earlier date, but it only lasts a day or two.  I searched for another fix and tried many things, including to reset the router, remove my network, and then reinstall, etc, but can't seem to get this to work as if it were - automatic connection as the first network.

  Any help would be appreciated.  Thank you.

  You have rebooted the router and the pc at the same time?

  You run the IPCONFIG / all from a cmd prompt can and download a preview of the output to a file share services like rapidshare and put a link to it in your next post?

• WRT110 connects unencrypted wifi, but fails to connect on any form of encryption

  all about the wrt110 seems to be okay, but when I try to set up a password it stops working. the broadcast ssid, and it isn't that I have the wrong password, but I get an error saying failing to connect. but with I disable encryption, then it connects very well.

  IM on a mac using firefox and safari.

  I feel like I've had this problem before, but I don't remember what I did to remedy

  thaaaaank you for ideas, or if someone has had this problem that would also be good

  Change the settings on your router wireless-

  Open an Internet Explorer browser on your computer (desktop) wired page. In the address bar type - 192.168.1.1 and press ENTER... Let the empty user name & password use admin lowercase...
  For wireless settings, follow these steps: -.
  Click on the Wireless tab
  -Here, select manual configuration... Wireless network mode must be mixed...
  -Provide a unique name in the name box of the wireless network (SSID) in order to differentiate your network from your network of neighbors...

  -Set the Standard - 20 MHz Radio band and change the Standard channel to 11-2, 462 GHz... Wireless SSID broadcast should be enabled and then click on save settings...
  Please take note of the name of the wireless network (SSID) because it's the network identifier...
  For wireless security: -.
  Click the sub-tab under wireless > Wireless Security...
  Change the mode of WEP wireless security, encryption must be 64-bit. Let the empty password, do not type in anything...
  Under type of WEP Key 1 in all 10 numbers please (numbers only and no mailbox for example: your 10-digit phone number) and click on save settings...
  Please note the 1 WEP key as it comes to the security key for the wireless network...

  Click the settings advanced wireless
  Change the interval of tag to 75 > change the Fragmentation threshold to 2304, change the RTS threshold to 2304 > click 'save settings '...
  Now let's see if you can locate your wireless network and try to connect...

• WMP110v2 network connection, but do not open web pages

  I have a Dell 2 GB of Ram and XP PC with the latest service packs and updates. No apparent reason, I had a little difficulty with the installation but after only two tests, but I the WMP110 to properly install and connect to my wireless connection. I use a D - Link Wireless Router N DIR-615 and my other wireless devices are running smooth.

  My problem is that my wireless connection will not go to the internet and I tried to use the Linksys monitor, but also Windows network utilities to check the problem and run the wireless but not connect me. The Web page tries to load, but then ends with the screen 'diagnose connection '.

  I think it will be easy but don't have yet to see a post explaining this problem and I don't know what to try next. Any help would be appreciated.

  Thank you for your interest in Klatch - I got it working well. As the biggest computer frustration usually boils down to a few clicks. For those who have the same problem, here is what has held back me.

  Until I'm able to get a connection I had to find some time to figure out how. Until I went in: WIFI - right click on the wireless connection, and then select PROPERTIES - click on the tab that says WIRELESS NETWORK -, PROPERTY - and then, AUTHENTICATION - once you see a checkbox indicating "authentication enable 802. 1 x for this computer"- UNCHECK this box. You will be able to connect to the wireless network.

  Then, my next problem and the reason for this post was that my network is connected, but I could not display web pages. This solution is buried in the manual on the CD itself. To resolve this issue, you must go into the DEVICE MANAGER to view the Linksys WMP110 under network adapters. Click on in the driver, then go to the ADVANCED tab. Here, you will see a list. You will need to click on the NETWORK TYPE. You should see two types of networks that you can select. The default value for mine was INFRASTRUCTURE. I had deselect this and select AD-HOC instead. My web pages now appear quickly, and I can browse the internet with wireless only!

  My setup is a N D - Link DIR-615 wireless router. I run Windows XP Home Edition on a Dell system. My type of security is WEP.

  Hope this info may help others.

• WUSB600N detects the wireless network, but fails to register.

  Hi all!

  Recently, I bought a WUSB600N adapter for my pc to share a wireless network and internet between the WAG120N router, my laptop and my pc. I installed the adapter successfully in my pc, but whenever I try to connect to the router, it detects the network wireless signl forcefully excellent, but fails to establish a connection. The error indicates that the security key is incorrect or the router is not in the range of availability. As mentioned, the signal is strong and the key is correct. I even removed the security key once and tried to connect, but the results were the same.

  So what's the problem? What should I do?

  Thanks in advance.

  I finally managed to fix the problem.

  I realized that my WUSB600N MAC address is not registered with the router. I tried everything possible and it didn't work... untilI I entered the adapter ' MAC in authorized MAC addresses for the router. and now it works perfectly.

  I think I have to get along that the adapter has serious problems with XP in the first installation, but after the have registered manually, it works fine.

• I can connect to ad hoc networks, but cannot navigate

  I have a compaq laptop with VISTA home SP2 original base. I have can create and connect to ad hoc networks but once established connection, other computers on the network do not appear on my network card, so I can not navigate on their.

  they can see my laptop on their network, but they can't sail too not my camera. It is shown as "inaccessible" on their network

  I activated files and printers, sharing, file sharing and all the options.

  XP and 7 do not have this problem, vista laptop to have this problem

  Please help, I'm frustrated

  Thanks in advance

  Hello santu

  The link below has a multitude of steps that you can use to try to resolve this problem. I hope this helps.

  http://forums.techguy.org/networking/925138-solved-ad-hoc-network-CMPTR.html