VRTX - NIC firmware update

Similar Questions

• GS716t V2 firmware update download for switch

  Hello

  in recent years, I have visited this site.

  I'm trying to update my 716v2 to version firmware, version 18 running 19.

  Using http download I can select the extracted the zip as a .stk file but the downoad never starts.

  I tried this a Mac and a PC running in parallels on the MAC and nothing happens.

  If left long enough the session times out.

  I forgot to add this switch has 2 VLANS active and I'm doing the upgrade of the designated vlan.

  Ian M

  Hi people,

  fixed the problem of say it both on the switch. The sad thing about the firmware update process is the lack of process indicators.

  After updating the switch sees a little faster and yes it has been restarted recently to overcome locking port that would not speak directly to a processor intel NIC on the firewall, but through a 'normal' switch

  Ian

• SOLVED: Slow wireless internet passthrough after firmware update

  If I first bought a Nighthawk in July 2014 and it was great for a while. Then in the notice happened a few months my streaming services are jumping and more than usual buffering (which was almost never with the Nighthawk).

  I have a connection of 110Mbps (Comcast and through a SB6141 modem), but all of a sudden was only getting 10 Mbps (or less) passthrough on 5 G wireless band (at the beginning of the speed test would sometimes up to 50 Mbit/s, but on a few seconds would fall to nothing..)

  Cable speeds were very good. Always 110Mbps +. Tried several different channels and factory reset the router, wireless speed was still slow. Connected to the Netgear website and submitted a support ticket within 2 hours they sent me with an RMA number and the next day a new unit has been FedEx would be for me. Support rep Tech says it's a problem of material known in some units... I was super impressed with the customer service, it was seriously a no replacement of hassles that took every 15 minutes of my time.

  EXCEPT when I got the replacement router in the next few days, he had the SAME PROBLEM. As soon as the new router is on and I'm connected, I've upgraded to the latest version of the firmware, done a factory reset and down Speedtest. And I had the same problem: speed internet passthrough on all my wireless devices has been terrible. Less than 10 Mbps when I have a connection 110 + Mbps. (Wired speeds were great, it was not a problem of modem or provider).

  Again contacted support and they asked me to download the latest firmware on laptop and upgrade the router manually, do a factory reset before and after the upgrade. They also told me to try to disable WMM (made no difference speed passthrough, but lower my laptop connection between 433Mbps to 54Mbps speed!).

  I tried this... still slow passthough wireless speed.

  The only thing that has changed since I first got a Nighthawk in July 2014 (and I've run speedtests then and had a speed 110 wireless + Mbit/s at the time), is that the firmware has updated several times... makes me think...

  I downloaded the Netgear support the past 5 versions of the firmware for the Nighthawk. http://downloadcenter.netgear.com/en/product/R7000#sear...

  I then manually downgraded the Nighthawk to each previous version (do a factory reset before and after each installation) and ran Speedtest every time. Once I have got down to the R7000 Version - V1.0.3.24_1.1.20 (released 12/02/14) and ran a Speedtest, the PROBLEM has BEEN RESOLVED. Speed wireless devices (laptop, HTC a M7 and iPad Air 2) were all back up to 110Mbps or more!

  Hope this experience helps someone else... If your are affected by the passthrough slow internet speeds and it is not your connection speed (i.e. radio parasites) that is the question, there seems to be a serious problem with the latest latest versions of couple... Try downgrading to the R7000 firmware version - V1.0.3.24_1.1.20

  UPDATE: Yes, I actually tested the speed with several different devices (a laptop HP HTC a M7 and Nexus 9) each on 5G band, all compatible with the latest updates ac. I also used a few test sites of different speed (speedtest.net, comcast speedtest, cnet speed test), not had the same result all devices and hosts.

  However, I actually got in touch with Netgear L2 support for the last month... beta test a few different versions of the firmware of the Nighthawk and even spend more than an hour on the phone one night with a nice guy who told me he was on an island in Southeast Asia, part of the Philippines... This is where Netgear technical support is to halfway between China where they build them and Taiwan where engineers are. After trying all tweak he could think for an hour and not get better speeds wireless, he finally dropped out and wished me a Merry Christmas lol. Not one of these beta firmware made a bit of difference, and I hate the hours that they made me screwing around with them!

  BUT today, they released vR7000 - V1.0.4.14_1.1.50 http://support.netgear.com/product/r7000

  And to my surprise it actually worked! Not only my high speed wireless is returned (120 + Mbps)

  http://www.Speedtest.NET/my-result/4078979293 (laptop)
  http://www.Speedtest.NET/my-result/a/1131321713 (nexus 9)
  http://www.Speedtest.NET/my-result/a/1131332778 (htc a m7)

  but also my Seagate SRD0SD0 previously incompatible (3 TB) USB 3.0 external hard drive works now, too. What a bonus! The reason I bought the Nighthawk was to use as Server DLNA and the monster external HD I picked up 6 months ago only was on the long list of those incompatible with this capricious router.

  But now everything works (at least for now).

  P.S. Maybe it's in my head, but I swear to you that since the last firmware update when running speedtest now or file transfer (while heavy streaming) I can hear the router doing a greater slope electric buzzing/hissing noise is a little disconcerting... I'm not sure my brain fried by overclocked wifi will be worth a high speed in the end...: eek:

• HP P2055dn Laser printer. Firmware update does not work.

  HP P2055dn Laser printer. Win 7-64. USB is connected. Download the appropriate firmware update, ljp2055dn_FW_Update_20120131.exe. Running the file. Select the printer in the dialog box. Printer has been powered up and ready. Bar showed progress update was sent to the printer and concluded successfully, with a smiling face in the dialog box. However, printer doesn't react at all, just keep to indicate loan. When the Self Test / Configuration page, it always shows firmware like 20111214.

  Printer works fine. The update is supposed to fix a security hole.

  Found the answer on the support page for businesses. Buried in the Menu of configuration, to the terms of Service, the last menu item is RFU. This determines if the firmware can be updated. The default value is OFF and LOCKED. It must be put on updating the firmware. After update, it will automatically return to CLOSED and LOCKED.

  It would have been nice if HP put it in the manual, rather than trying to pay $35 for the support of something that should have been documented. Must be a secret or maybe I'm the only person who didn't know what that meant the RFU.

• on printer_what wireless firmware update will allow to connect a cable to screw?

  Instructions for JO 8600 Pro n911a HP says the firmware updates don't work for wireless connections.  Using Vista x 64.

  That I have not found, this is what can happen when I plug a printer already implemented wireless with a USB cable or ethernet.  And how many ways can he screw up my installation of the printer?

  Nothing is mentioned in the manual on this printer support page or the user on the CORRECT way to change from USB wireless or ethernet - TEMPORARILY, updating of the firmware; then return wireless - w/o problems.  Which is not a common question?

  In addition, I don't see a way to say positively what firmware version is later.  The versions are different, but not like xxxxx100 & xxxxx105.

  First characters of the firmware & a to d/l are the same; last digits of the current FW are 1150CR. There is no date for the installed FW, anywhere, I looked. 

  Version more recent d/l is 1304AR.

   

  I've seen a lot of files / names of the drivers where the last 2 characters - CR & AR - would be more wrinkle is that the 4 last digits are higher on the d/l version; as this is a new printer.
  

  Thank you.

  Hello lostsowl,

  I think that we are on the same page.  I was using different terminology for the same thing.  I use the word 'install' to mean 'add printer' or 'other connection of installation.  A printer can be connected to a computer through different types of connections.  Each type of connection would require a separate installation, although you can use the same software.

  Looks like you have made a reasonable decision.  If I can do something else to help, let me know.  Nice day!

• QLogic NIC firmware and drivers on 11G servers

  Hi all

  Can someone explain why the new QLogic NIC firmware (formerly Broadcom) and the pilot are not shown on the pages of download for 11 G- servers?

  We have a bunch of R710 servers (Windows Server 2012 R2) with NIC BCM5709C NetXtreme II which, according to the release notes are compatible with these new updates.

  If you go to the download page for R710, these files are not, (only older files of Broadcom).

  Instead, I run the last SUU (15.04.200.109) on a R710, the pilot and the new fw QLogic are listed as extensible.

  A strange thing here is that the version of fw-package in the SUU is 7.12.15.
  (I can't remember having seen the version of the Driver and download pages).

  "QLogic BCM57xx and BCM57xxx Network Device Firmware 7.12" version which is downloadable for example R720 is 7.12.17.

  Verifying compliance on R710 to OME with the latest version of the catalog, no new QLogic driver or firmware appears.

  I have applied these new QLogic on a R710 updates in our lab and installed both without problem and seem to work well.

  I am bit confused now and would like to know if Dell supports the driver and QLogic fw on R710 with NIC BCM5709C NetXtreme II

  Larnil,

  Thank you for bringing this to my attention. According to me, that it was simply an oversight due to the change of name, following the acquisition of Broadcom by Qlogic. We will look on getting the page corrected to reflect the most recent update.

  Thank you once again.

• DSC-hx200v for remote usb firmware update?

  The DSC-HX200v is a nice camera, but it has some annoying features.

  Top of my list is unable to disable filtering of noise - it can be set to high or low, but even 'low' causes really ugly image artifacts.  For detail work, it would be preferable to disable filtering altogether in the device and use image processing software to clean the sensor noise.

  Second on my list is the lack of a remote - camera trigger must have at least one command trigger USB, or a more complete control APIs, to allow a laptop computer collect the series Time lapse.

  My third wish list is trivial - adds an average speed (4 to 5 fps) burst mode.  I had many opportunities when 10 FPS is too fast and 2 images per second is far too slow - intermediate dieting (or the ability to set the value of fps as you can the shutter speed and ISO) would be just the ticket.

  So my question is if Sony ever plans to publish an update of firmware for this device, and if so, what changes are planned?

  Hi Tad,

  These are good options. Firmware updates are released frequently to provide enhancements to existing features. Our engineers regularly focus on these positions. I don't know that they're going to try to incorporate these options in future models.

• firmware update

  I tried updating my two cinema Display on my iMac (27 inch, end 2013) iMac Intel Core i7 3.5 GHz 32 GB 1600 MHz DDR3 NVIDIA GeForce GTX 775 M 2048 MB tons of time, using all possibilities, but unfortunately not worked.

  What is happening with this firmware?

  Hello RUBENSCOSTA,

  Thanks for this info and choosing the communities Support from Apple. I know how important to get your Cinema Display works again is for you!

  If I understand correctly, you are unable to update the firmware on the LED Cinema Display. I would like to try the following steps to get these working again:

  1 make sure that your iMac has all available firmware updates installed as well:

  On the updates of the EFI and SMC firmware for Mac computers with Intel processor

  2. try to follow the process in this article on the updating of the LED Cinema Display Monitor:

  On the 27-inch LED Cinema Display Software Update 1.0

  3. If you're still having problems, you can see the general troubleshooting guide:

  Get help with your Apple Cinema Display Monitor

  See you soon!

• Airport Express firmware update

  I had a Firmware Update for my Airport Express.

  How can I update? I can only choose ignore, do not to update. In other words, what I did now.

  Zu-updates information to update Firmware as airport-Basisstationen - Apple Support

  It's funny. I think it's a bug.

  Airport-Dienstprogramm 6.3.6 on El Capitan

  "You are not allowed to create or update this content" - funny too.

  This firmware it works now?

  What model is the Express?

  You can do it manually even if it is a bit complicated.

  Re: proxy server annoy 7.6.7 update?

• Wan interrupts the connection after the firmware update

  Looks like the latest firmware upgrade is the source of the problems.

  I've just updated my timecapsule 1 TB of first generation version 7.6.7 and my 3 TB timecapsule new version 7.7.7

  Both are connected to the router of the provider of Internet services and extend the network even in my house.

  WiFi is stable until the upgrade, but now the connection is lost every few minutes or seconds.

  Both versions are later to the respective timecapsules.

  I end up having to downgrade if no solution is found.

  I powered the two market still nothing does not. Redefine the network and tried both hidden and not hidden, yet once nothing doesn't.

  Any ideas on what is causing the problem?

  Well, since nobody seems to have an explanation, and Apple are not out with firmware update after 7.7.7 and 7.6.7 I decided to downgrade the firmware to the previous version. I now run version 7.7.3 on the new 3 Tb Time Capsule and 7.6.3 on the 1st Gen Time Capsule. So far, the network is stable. Using WiFi Explorer Ii see that they use channel 6 and 8 respectively. Signal is strong and no dropouts have taken place so far. Hope the issue is resolved in the next firmware update.

  As I read in another post: firmware update does not solve a problem, you didn't. However, it can create a problem that you didn't.

• TimeCapsule Firmware update 7.6.4 is not possible

  on my Timecapsule is not possible firmware update.

  Airport utility shows me that there is an update, but I have no button to update.

  

  Hold down the option key and click two times on the base station. before an option there will be updated to version, click on it.

  The system will reboot and firmware will be updated.

• Airport Extreme Base Station model bricks A1408 after failed firmware update

  Shown on Macbook Pro iOS X 10.10.5 airPort utility update the firmware available for both devices on my network 3 June 2016
  1 Airport Express 7.6.7

  2 version of Extreme Base Station Airport unknown as not reported as I expected not die

  After the update successful of the AirPort Express, the update cannot be installed on the Base Station firmware.

  After waiting a while, I tried the update again which also failed to install.

  Current symptoms:

  a. the Base Station is hot indicating energy consumption

  b. No. LED light is during the power on self test or during the race

  c. not discover measure on the WIFI network

  d. is not identified on Ethernet connection without light next to the Ethernet port

  e. DC output is 12V on the connection of the power supply works as expected

  f. cannot perform factory reset using the reset button on the back of the Base Station

  Where other devices working on the same power supply as the Base Station that very sensitive to power outages - these remain functional during the attack of upgrading me to think that he has not lost power while firmware update took place.

  My home network is made entirely of Apple devices - should I worry on the application of the firmware updates in the future.

  It's embarrassing and I now Cat5 running through my house just to maintain services.

  I can't confirm the date of purchase, so I don't know if it is covered by the warranty, however, I'd like to think Apple would cover this.

  What I am doing wrong and y at - it a way to recover the device.

  Help

  We have seen a few posts of users who have had the same problem.

  Unfortunately, not a really nothing you can other your advocate Support of Apple.

  Good luck and hope that you will have this resolved quickly.

• Cannot run AirPort Extreme or Express 7.7.7 Firmware update-> gray button

  Hello!

  I have an AirPort Extreme and Express stations. Both come with a pill that indicates a upgrade must be performed:

  

  Now, I click on the AirPort Express icon. The following window appears:

  

  He told me that a Firmware update is available. But in this window, I can only select "ignore". I can't select the choice of the update.

  If I click on the "Edit" button to change the settings of the station:

  

  But in the window that appears, the "Upgrade" button is gray:

  

  The same thing happens when I click on the icon of the AirPort Extreme station.

  What is the secret path to the update of the Firmware 7.7.7?

  Thank you

  JHR

  Montreal

  MacBookPro 13 "mid-2012. 10.10.5 OSX

  Click on 'version' and you should be able to update from there on.

• TimeCapsule downgrades WiFi 2.4 GHz after applying the firmware update v7.6.7

  After applying the firmware update v7.6.7 free WiFi to TimeCapsule is now 2.4 Ghz instead of 5 Ghz.

  It was the update of the firmware with certainty that has made this... no doubt about it:

  • My mouse bluetooth interference notice when my MacBook is connected to WiFi 2.4 Ghz;
  • Before the update, everything is OK
  • After updating, my mouse mouse start jittering
  • < alt-click > WiFi icon in the menu bar confirms: the connection is now 2.4 Ghz

  Restart to e TM Mo doesn't change anything.

  In the TC WiFI options tried to put another name to the network successfully, but only 5 GHz can not connect to it: timeout error every time.

  Tried the hard reset of TC and reconfigure the WiFi... the same result, but with a difference:

  • Setting an SSID separated for 5 GHz connection (in the WiFi options) has now created a network I can access.
  • However, this is not the best solution... I don't want 2 SSID.

  It is not the first time Apple breaks things with updates... and I see people move away from Apple to this kind of situations.

  I also had bad experiences with OS updates lately and postpone the as much as possible.

  The problem is that I can't go back... or can I?

  Any help is welcome.

  THX

  The problem is that I can't go back... or can I?

  Of course, you can, but it may or may not help.

  Open AirPort Utility

  Click on the image of the AirPort base station

  Hold down the option key on your Mac while you click on the version number of the firmware

  A drop down menu appears

  Choose the version of the firmware you want to use

• TimeCapsule firmware update error, now defunct

  I received notification of a firmware update for my TimeCapsule AirPort, then click it to start the update. He seems to have run the update and was himself reboot after the bar got to end state. He came back with a message 'update error occurred'. Now the airport is not at all in the AirPort Utility window. Tried unplugging the power at the airport to force a reboot. Tried the manual reset button, still not joy.ow I have a constant flashing orange.

  Now, it's just an amber flashes continuously. And nothgin all appear in AirPort Utility window.

  Thoughts?

  Tried the manual reset button

  Sorry, don't know what this means, because there are 3 types of resets.

  Have you pressed the button of reset for 1 second and then release?

  Do you have the reset button during 5-6 seconds and observe the led flashing quickly until you release the reset button?

  Or something else?

  Have you restarted your Mac?