QLogic NIC firmware and drivers on 11G servers

Similar Questions

• Update of firmware and drivers controller PowerEdge 2900

  Hello

  I have server PowerEdge 2900. Current configuration I see on OMSA:

  BIOS version 2.3.1 (former)

  Controller PERC 6 / i integrated.
  Version of the firmware is up to date.
  Firmware Version 6.0.2 - 0002
  Minimum Firmware Version 6.3.0 - 0001
  4.05.01.64 driver version
  6.1.7601.17577 Storport driver version

  I need to upgrade the firmware of the controller and make the Windows updates on this server. My questions:

  What is the correct order for the upgrade:

  1. Windows updates
  2. BIOS,
  3. ESM firware,
  4. Bottom of basket SAS firmware,
  5. Disk controller
  6. Firmware of the controller,
  My questions would be:
  How can I verify ESM and bottom of basket SAS version of the firmware on my server, maybe I do not need to update those?
  On the Dell support site, I could find only:

  Dell Server BIOS, 2.7.0Dell SAS Backplane Firmware, v.1.05, A01Dell BMC Firmware, v.2.50, A00Dell PERC 6/i Integrated, v.6.3.1-0003, A14
  

  and how to find software to update the drivers:
  4.05.01.64 driver version
  6.1.7601.17577 Storport driver version
  ?
  The Dell supports any automatic tool to collect and install the drivers and firmware required on a single server of Windows (except ITA)?
  Server is very critical, thanks,

  Yes, it's safe.  It can be run from within the OS, or you can start on SBUU and serve Suu repository for update packages.

  In most cases, it is easier to update of Windows, but it is not necessary.

  1. Windows updates
  2. BIOS,
  3. Environmentally sound management software (Yes, must be updated to BIOS).
  4. Bottom of basket SAS firmware (also needed),
  5. Controller driver (did you mean driver here? pilot, when it is available, it should be updated before... If current firmware to run 2008R2, new drivers are available through Microsoft Update - if available)
  6. The controller firmware
  7. The hard drive firmware
  8. NIC, DRAC, etc..

  When / if get the support.dell.com site update files, use Packages to update for the format of Microsoft Windows.

• Need to sounds of Windows XP Home edition and drivers NIC for Satellite A215-S4817

  I removed Vista and installed Windows XP Home edition on my satellite A215-S4817 but the I am unable to get a sound or recognize NIC

  Vista drivers do not work... Help!

  Hello

  I don't know where you looked drivers but if you have a model of cell phone US please check http://www.csd.toshiba.com/cgi-bin/tais/su/su_sc_home.jsp

  It's very good support page and I hope that here you can find everything you need. If the drivers of Windows XP Home Edition are still not listed, as European for A210 page, it means that support for Windows XP Home edition is not yet started.

  On this forum, you will find a large number of discussions on the drivers of Windows XP Home on Satellite A210. Please check. Maybe you will find some useful information.

• ElitePad 1000 G2: 10 Pro Version 1511, threshold 2 update Windows crashes on 'features and drivers '.

  Summer running Windows 10 Pro 64-bit for months without problem on my G2 ElitePad 1000; application Windows 10 updates throughout - so far. Yesterday, 12/11/2015, 1511 (threshold 2) updated version of Microsoft automatically downloaded and rebooted to start installation of operating system upgrade. The upgrade completed the first phase "Copying files" and began the second phase "Patterns and drivers", then stopped (paused) to 40% total progress/23% features and drivers progress with no other response. Only one stop 'hard' (hold down the power button / stop for at least 10 seconds) worked. On 'power up' the result was a "restore previous version" immediately, and subsequent reboot restored my previous login - as expected.

  HP have a new image or update for Windows Pro 64 - bit version 1511/threshold 10 2? The update is put on hold due to a driver issue? Any advice would be appreciated.

  Finally, a solution for me! I used Microsoft's latest "MediaCreationTool" (as of 11/13/2015) to download and create a "USB stick" (08/01/2016) upgrade support. Stick created USB contained more than 3 GB of content upgrade. Started my ElitePad in my 10 original Windows operating system upgrade, and then insert the USB in my ElitePad. Launched "Setup.exe" on the USB key to start the process to level, and left the USB connected until the upgrade is completed; several reboots of the upgrade. Once launched from Setup.exe, a menu background blue proceeded and displays "Check updates" for more than 15 minutes (check the updated drivers, etc.), and then proceeded to the display of the upgrade process (progress circle GUI). The upgrade has completed in 90 minutes without a hitch. So far, all programs and functions are intact. I guess that is focused on the HP drivers updated (finally) in the current construction of 1511, and/or the last created USB stick media works where Microsoft Update (via Microsoft Update servers) has a problem. For me, this solves my problem to upgrade v1511. I hope this helps others.

• Broadcom/qlogic npar distributed and strategy MPIO on Windows 2012R2

  Hello

  I enabled Distributed on partition 0 in our FC630, card broadcom/qlogic 10GbE. After all configured on MS iscsi initator then I saw all the paths were active for some time (10-20 min), then one of the paths is all just disappeared and never reconnected.

  I see the message "disconnection request has been received from the initiator" on the EQL newspaper but is not very useful. Curiously, it was precisely the LUN; I saw no problem for vss-control. So I was check the option and I noticed that if I change the "least queue depth" MPIO "failover only" then I see no loss path.

  As I'm not sure why the default "least queue depth" option does not work, I would be grateful for any insight and details.

  Thank you

  Hello

  If you open a support case, they probably have you say that it works as expected.  Since EQL FW 6.x our MPIO code negotiates connections as needed.  To ensure effective performance and minimize the number of connections.

  The event message you included confirms that.  The "requested disconnect" comes the HIT MPIO code.  The 6210 has vertical tipping so with little traffic that one connection is necessary. A failure of the cable or switch will not lower your volume.   If the load rises another connection will be established.

  The settings in the registry that Michael mentioned substitute is no longer trading code in the firmware and the HIT.

  Is there a feature request for the connection of two minimum for better offer peace of mind to our customers during this behavior.

  Since you are dealing with a single member, the greater benefit of our code MPIO is not be used.   This requires several members in a pool.   With a single member, you won't see any difference w/LQD on Round Robin.

  Kind regards

  Don

• continues windows server reboot after firmware and enic fnic upgraded 2 has 2.1 to 2.2 6 d

  We are faced with the issue of the continuous reboot on the domain controller after the upgrade of the enic, firmware and update driver fnic upgrade of

  2.1 2 a to d 2.2 6.

  I guess that's an installation on the local disk?

  Are there any that any Windows crash dumps?

  Windows only (if you don't start AD) work?

  Have you tried to downgrade the drivers again (it is fully supported so that the infrastructure running at 2.2.6d)?

  http://blogs.technet.com/b/robertsmith/archive/2013/04/16/Windows-2008-r...

• Find the version of the HBA Qlogic HP firmware

  I have new HP BL460c ESXi 6.0U1 servers.  I looked in the directory/proc/scsi /, but there is no record of qlaxxx version.

  Can we all up to me how to find my version?

  Thank you

  Check if help: audit HBA Firmware and driver in ESXi 5.5 | VMware-Pro

• 554FLB 10Gb - Emulex Corparation HP FlexFabric 2port / 554 M - unstabile after the firmware and the network upgrade driver

  Hello everyone

  I upgraded 2 HP Gen 8 Server on Monday of SPP "2014090.2014_0827.10" firmware and HP ESXi drivers 5.1 U2 September 2014.

  firmware 10.2.340.19

  Driver 10.2.293.0

  After two hours lost both connections to the server. In Configuration/network adapters all missing devices and after awhile they returned to display.

  Network cards have been disabled in the Configuration/network.

  After reboot, all the network were OK but the problem again.

  The only solution I found was a rear roller for the firmware and driver net b2net.

  firmware 4.9.416.0

  Driver 4.9.288.0

  Does anyone have the same problem?

  Thanks and greetings

  Denis

  Yes, I saw two other reports of similar problems.  I happen to run ESXi 5.0 U3, but I was careful to use the latest HP recipe/package of Sept/Oct because of this problem. Check out the blog on this subject at the following site - ICT - Freak.nl

• Teradici 4.0 firmware and SAN certificates

  Use a SAN cert on my servers connection that has on the entrances to SAN a dozen without problems on zero clients with 3.51 firmware, but after upgrading to one of the clients to 4.0 firmware, I now get a warning indicating that the certificate is not trusted, and I see not what follows in the zero client connects :

  20/05/2012, 09:12:19 > RC LVL:3: 0 MGMT_SYS: (ui_cback): event: 43
  20/05/2012, 09:12:19 > RC LVL:1:-505 X509_UTIL: x509_util_subject_alternative_name_cback: SAN buffer is full
  20/05/2012, 09:12:19 > RC LVL:1:-505 X509_UTIL: x509_util_subject_alternative_name_cback: SAN buffer is full
  20/05/2012, 09:12:19 > RC LVL:1:-505 X509_UTIL: x509_util_subject_alternative_name_cback: SAN buffer is full
  20/05/2012, 09:12:19 > RC LVL:1:-505 X509_UTIL: x509_util_subject_alternative_name_cback: SAN buffer is full
  20/05/2012, 09:12:19 > RC LVL:1:-505 X509_UTIL: x509_util_subject_alternative_name_cback: SAN buffer is full
  20/05/2012, 09:12:19 > RC LVL:1:-505 X509_UTIL: x509_util_subject_alternative_name_cback: SAN buffer is full
  20/05/2012, 09:12:19 > LVL:1 RC:xFFFFE8E6 MGMT_SSL: ocsp_http_query: remapping error at ERR_OCSP_RESPONDER_CONNECT_FAILED
  20/05/2012, 09:12:19 > LVL:1 RC:xFFFFC552 MGMT_SSL: mgmt_ssl_certificate_revocation_test: mgmt_ssl_ocsp_validate_certificate() failed: unknown error
  20/05/2012, 09:12:19 > LVL:2 RC: MGMT_VDMCSI-500: warn the default display mode: certificate of VCS responds WoVD no exception of root of trust

  I have an open ticket with Teradici (nine days) and still no reply from them, other than a ticket status of ' Work in Progress '. Anyone else see a problem with the 4.0 firmware and CERT with multiple SAN entries?

  Thank you

  
  Geoff

  Had the same problem with our Digicert wildcard

  I downloaded the intermediate cert as a .pem only through a new profile and psuhed on some P20 test - all good

  The Digicert called Digicert High Assurance CA-3

  

  

• VRTX - NIC firmware update

  I might be missing something obvious, but I can't understand how to upgrade the firmware of the network adapters attached to the chassis on a VRTX.

  Mapping a map NETWORK to blade and trying to update its firmware to the blade iDRAC do not work (it does put a job in the queue, restart the server and go as far as the update screen, but then fail).

  And there is no tab "update" on the CMC interface for PCIe components (it is one of the components of the storage, so I expected to type something similar...).

  Any idea?

  NICS are Intel I350-T4. Current firmware is 15.0.27. The target firmware is 16.0.24. Everything else on the blades and chassis VRTX is the most recent version, AFAIK. It is a license of CMC Express.

  It turns out that I have has been missed something obvious and this is the important information section on the support page of the firmware (lack a bit of professionalism, it is true...). That clearly states that you cannot go directly from 15.0.27 to 16.0.24 during the upgrade by the controller of the life cycle of the blade (via interface iDRAC, iDRAC settings/update and Rollback). What you have to do is to 15.0.27 --> 15.5.0--> 16.0.24. And indeed, it works. If this has nothing to do with the VRTX and with this specific NIC firmware.

  Thanks in any case Chris to try to help, it is always appreciated.

• How to check firmware and the version of the driver on Dell details

  I need to upgrade the version of the firmware and driver on a Power Edge 2950 server. Please let me know is there all orders for this information. I use the Windows 2008 R2 64-bit version.

  First of all, download and install OpenManage Server Administrator (OMSA):
  http://www.Dell.com/support/home/us/en/04/drivers/DriversDetails?driverId=V1JDD&FILEID=3365593125&osCode=WS8R2&ProductCode=PowerEdge-2950&LanguageCode=en&CategoryID=SM

  Download and run to extract the files, and then run C:\Openmanage\windows\setup.exe, choose custom and make sure that storage management is installed.  Add your servernameoripaddress:1311 to the Intranet Zone of IE.

  You can use OMSA to display the current firmware and driver versions.

  Once you have established versions, you can get the latest version from here:
  http://www.Dell.com/support/home/us/en/04/product-support/product/PowerEdge-2950/drivers

  Updating BIOS and ESM firmware, first, and then on the other (drivers before the firmware if necessary).

• Language software and drivers

  How can I force the software and drivers for my Color LaserJet CM1015 MFP to install in English and not in the default language.

  I have a Portuguese (pt) windows xp and the software tries to install Portuguese (br) versions, this is not acceptable!

  THX.

  Hello

  To resolve this problem, follow the steps below.

  Windows XP

  1. uninstall the SW if you have successfully installed the driver.

  2. remove the install CDROM or DVDROM drive.

  3. Click Start, control panel and select regional settings.

  4. click on advanced.

  5. change the "language for non-Unicode programs" to "English (United States)".

  6. check the box for the default user account settings.

  7. click OK and restart when you are prompted.

  8 put in the installation CD and install the printer software. Joanie you see installation screen in English.

  Windows Vista

  1. uninstall the SW if you have successfully installed the driver.

  2. remove the install CDROM or DVDROM drive.

  3. open regional and Language Options by clicking the start (Windows icon) button, click Control Panel, click clock, language,

  and region, and then click regional and Language Options.

  4. click on the "Administrative" tab, under the tongue for clcik programs no unicode on "change system local." Select "English (United States).

  5. click OK, and then click Restart now.

  6. put in the installation CD and install the printer software. You should see the installation screen in English.

  Kind regards

  AlmostThere

• Need to update the BIOS and drivers for Satellite Satellite Pro A10

  I have a Toshiba Satellite SPA10 model num E = 09VYL-PSA15-EN. I searched everywhere but can not find update BIOS and drivers for this model of laptop.

  Please provide me with a link.

  Hello Debbie

  There is no such thing as SPA10 satellite. You either have Satellite A10 or P10. Please check on the label at the bottom of your laptop. Correctly identify your laptop model and you will find everything you need on Toshiba download page.

• Stream HP 200-009: replace SSD (hard drive) and reinstall Windows and drivers

  Hello

  My warranty is over a few months ago and I need to replace my HARD drive which is unnecessary, because all the space is taken by the OS, I can not upgrade to Windows 10. Could you please help me how to recover my key Windows and drivers HP before changing my HARD drive + tips on replacing drive HARD would be also useful. There is no service HP here so I have to do it myself.

  Thank you, I finally solved the problem by creating a partition under Advanced options and recovery of Windows drive, and you select Reset. Search for main windows and use Windows system image did not work with the version of Windows OEM.

• Is there any way to install the operating system and drivers without recovery CD?

  Hello...

  I installed my laptop with the recovery cd...
  but I disappointed because he installed many unusual programs like sonic-pro games, aol...
  What is a way to install windows and drivers only? without this annoying programs?

  I don't want to uninstall after instalation... This isn't the same thing...

  Hello

  Hello

  Why disappointed? It is not uncommon that recovery image on laptops (not simply on Toshiba one) contains different applications and software. No one forced to use anything, and you can remove it. I put t know why you think that this is not the same thing but in any case, you can use Microsoft Windows XP edition family CD and install the OS. After that, each driver must be installed separately.

  Everything you need you can find on the download page of Toshiba.

  Good bye