WAP321 captive portal - impossible to set up the guest network connection

Similar Questions

• Is impossible to turn on the guest account. Cannot create new user account. "The service user profile Service has no logon. User profile cannot be loaded. »

  Is impossible to turn on the guest account.  Cannot create new user account.  After to try one of those and reboot, the icons of account appear, but when you try to use, the following instructions of error present when you try to log in with the new account or comments: "the user profile Service service has no logon.  User profile cannot be loaded. "I looked at the answers to all the previous ones (including the KB947215) and no not to address specifically.  For the most part, they seem to assume that there is a guest or a new profile in the first place...

  The system is Win 7 Pro 64-bit with all available updates.  I can't say when the last time that the guest account has worked (rarely used) and just found out I can't do new additional user, accounts trying to solve the problem of account of comments... so I have not tried to enter Safe Mode and do a system restore , because I can't yet identify a useful restore point...

  There are no entries in the registry for a guest or a new standard user account.  The registry entries for the three accounts normal-quickly (2 x admin, 1 x level) seem to be appropriate.  Watch register computer/HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\ProfileList

  S-1-5-18 = system profile

  19 = local service,

  20 = network service,

  21 long numbers + 1004 plus User1 (admin),

  22 long + 1005 plus 2 user (admin),

  23 plus long + 1006 is user3 (standard,

  and no comments or additional profiles appear.

  C:\Users includes

  All users,

  User1,

  User3,

  By default,.

  Default user (which is inaccessible for me, even as an administrator),

  Public,

  User2,

  No guest or additional profile appear.

  All except the default user (I can't open) seem to have the appropriate, NTUser.DAT files although I don't know how to check for corruption.  Having both a default value

  and a default user folder seems hokey.

  I think I understand instructions how to fix or remove a corrupted profile, but that does not apply to the guest account or profiles that do not exist.

  Help?  Ideas?

  This message contains the strange solution.

  [Plan B - I found one thread where one user said that the same symptoms of the problem that you experience this problem solved]

  - - - - - - - - - - -

  Plan h - while another user said that it was caused by a file Windows Live problem

  This is the thread I can not create a new user account (Windows 7): the user profile service service doesn't have the logon

  You find it difficult to follow the thread as it's long and reported problem by different people to confuse it and there is also a bit of bickering [long filaments often end up being quite incomprehensible].

  ..., See references to the event viewer in the middle of page 4 and Windows Live we [at the bottom of page 2 more on page 3].

  I see not the logic of the any of those things, but if one of them do things long enough that you are trying to create new accounts that works, you will know how in the future until a proper solution is found.

  This is the useful part where this user has tested the solutions proposed in this thread linked above: -.

  This has proved to contain leads to a difficulty.  Have to admit, when I read everything the first time, several days, I did indeed find it confusing and even the parts that I "heard" (sorta) does not appear to be related to my symptoms.

  It turns out that the answer of JDMICHAL May 17, 2011 contained this:

  (1) C:\Users\Default\AppData\Local\Microsoft\Windows open live
  (2) this directory has two subdirectories with a single file of each. Go into each directory and apply the following:
  (a) make a right click on the file, open the properties.
  (b) click the Security tab.
  (c) it will issue a message: "to continue, you must be an administrative user with permission to view this object's security properties. Would continue you? ». Click on the button continue.
  (d) click on the Add button...
  (e) ' everyone' type in the box at the bottom of the dialog box. Click on "check names"; It should be emphasized the "everyone". Click OK.
  (f) ensure that the new "Everyone" entry "read" and "read & run" check under the column "allow".

  After doing this for two files, attempt to connect to the account. He must undergo.

  The procedure (bascially) worked... Although the different answers on my system differed slightly along the way (perhaps due to the slightly different versions of Win 7?, because I was already logged in as an administrator?).

  In any case, "Everyone" with the read and read/execute permissions adding to these two files seems to have done the trick:

  C:\Users\Default\AppData\Local\Microsoft\Windows Live\Bici\Bici1_00.sqm

  and

  C:\Users\Default\AppData\Local\Microsoft\Windows Live\SqmApi\SqmData720896_00.sqm

  Thank you for leading me to this!

• I can't print due to the "wireless network connection" doesn't have a valid IP address.

  Cannot print wireless

  I can't print due to the "wireless network connection" doesn't have a valid IP address.  How can I fix this problem myself (an absolute non-techie)?

  Hello

  -Did you change your computer, after which the question began?
  -Check if you are connected to the network?

  The question seems more like a network connection problem. I would like you to do the following.

  Method 1: run the Network Troubleshooter utility and see if the problem persists.

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

   
  Method 2: release and renew the IP (Internet Protocol) address and see if the problem persists.

  has. click Start. Type cmd in the search box and press ENTER.
  b. at the command prompt, type the following command and press ENTER:
  ipconfig/all (there is a space between ipconfig and /)
  The command ipconfig/all command displays for all your network adapters, TCP/IP in Windows settings.
   
  If your IP address of your Local network connection is 0.0.0.0 or 169.x.x.x (where x is a number any), then your computer is not getting an IP address from the router.
  If this is the case, try this:
  ·        enough ipconfig at the command prompt and press ENTER
  ·        ipconfig / renew in the command prompt and press ENTER

  Method 3:

  Network printer problems

  Note: The steps also apply to Windows 7.

• The active network connection icon keeps changing on me. He began by showing only 2 connections to the internet and the changes and then later to 3.

  Hi, the active network connection icon keeps changing on me.  He began by showing only 2 connections to the internet and the changes and then later to 3. But does not show where is this extra connection to connect to the local network.  I have a laptop so no wireless and cannot understand why he continues to display an additional connection.

  original title: network access connection

  Hello

  1. what version of Windows operating system do you use?

  Click on the link below.

  http://Windows.Microsoft.com/en-in/Windows7/help/which-version-of-the-Windows-operating-system-am-i-running

  2 has there been any changes to your computer until the problem occurred?

  3. have you installed all types of network adapters on your computer?

  4. are you able to connect to the network and browse the Internet?

  I suggest you to follow the troubleshooting steps and check if the problem on your computer is resolved.

  Method:

  Check if the network adapter is displayed in the Device Manager.

  a. right click on computer or workstation.

  b. Select manage.

  c. click Device Manager on the left was next to the window.

  d. on the right side, locate the network adapters and click the arrow to expand the menu.

  If you have multiple NICs installed (watch), I suggest you uninstall the network adapters that is irrelevant to your computer by right-clicking on the adapter irrelevant and selecting Properties and then select uninstall.

  Please provide us with additional information. So that we can help solve you the problem on your computer.

  Hope this information helps you.

• my pc will not connect to wireless internet... It is said there could be a problem with the driver for the wireless network connection card

  connection network card

  my pc will not connect to wireless internet... It is said there could be a problem with the driver for the wireless network connection card... I'm not sure how to solve the problem of the dat

  Hello

  Did you change your computer?

  I suggest you to follow the links and check out them.

  The problems of Internet connection

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Internet-connection-problems

  Solve problems, find wireless networks

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-finding-wireless-networks

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Tips for solving common driver problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-driver-problems

• Problems connecting to the internet using the wireless network connection

  I can't connect to the internet using my wireless network connection. I had made the diagnosis and he stated that "the DHCP is not enabled for the wireless network connection. I had checked the DHCP, but it has been activated!... Someone would give any suggestion for me to solve the problem?

  Open the run command box by pressing Windows key + R, type services.msc and press enter . Search The Client DHCP and check if it is enabled or disabled. If disabled then turn it on and see if the problem still persists or not.

  Open the run command box by pressing Windows key + R, type cmd , and press enter . At the command prompt, type ipconfig/all and press ENTER. Now, check the IP address, default gateway, DNS etc. If you find all the information is correct, but you cannot yet access the Internet so if you connect the wireless network is secure or not. To determine the glance to the wireless network icon in the taskbar, then click on it. It will show you the available wireless networks. If there is a "yellow shield" present on the network icon, the network is not guaranteed, if there is no "yellow shield" does while the network is secure. In a secure network, you might have a "network security key. In this case try to disable the 'Network security key' option for this network. To do this:

  Open Control Panel , click network and Internet , click network and sharing Center , click manage wireless networks on the left.

  In the list select the wireless network and do a right click, select Properties, Security disable tab all options that is, in security type do not select no authentication (Open) and to the type of encryption , select none . You can also activate the automatic connection and SSID settings to further enhance connectivity, on the connection tab, click to select the "connect automatically if this network is in range " and "check boxesto connect even if the network is broadcasting his name (SSID) .

  For more information click here and see how you can determine whether a network is secure or not.

  http://Windows.Microsoft.com/en-us/Windows7/how-do-I-know-if-a-wireless-network-is-secure

  If the problem still persists, then check your firewall settings and make sure that the firewall is not blocking your Internet connection. Some software Antivirus has a built-in firewall and they block by default all unknown connection to the tightening of security.

  Try to restore Windows Firewall default settings. Open Control Panel click on network and Internet , click system and security , click Windows Firewall , click default settings .

  Hope this will help. Thank you.

  Arup Ratan Paul

• problem witththe driver for the wireless network connection card

  Quite suddenly my laptop (Toshiba) could not connect to my Modem and printer. I can only connect to the internet with a cable connection to the modem. The printer reports no problem with the connection. Troubleshooting report 'Problem with the driver for the wireless network connection card.' Problems also with ISATAP MS Driver adapter and Teredo Tunneling adapter. Software could not solve the problem.  A technician online know-how also faled to solve the problem after an hour trying everything - uninstalling and reinstalling, etc. He thought it would be a virus even though I have several active antivirus programs. Any ideas? Should I chuck the laptop away and buy a new one?

  If, as you say, you have several active antivirus running programs, they will conflict with each other and you will have no protection

  Visit the support of Tosh, specific to your model, and reinstall the drivers for the chipset and wireless

• WAP321 - captive portal in 2 VLAN different

  Hello

  I have a Wap321 installed in my network.  IP: 192.168.0.36 - VLAN 1

  If I'm in the local network, I don't have any problem to use the wireless.

  I just added a guest VLAN for people who need to connect Internet, without access to the network. So I install a second SSID and label with vlan 50. I can access the Internet.  But if I want to active the captive portal, I can't access it because the address is in the VLAN 1 (or 192.168.0.36).

  How can I configure my Wap321 having the captive portal in the VLAN 50, and not in the VLAN 1?

  Thank you

  Alex

  Hi Alexander,.

  For interVlan on ISA5510 setting, yes the same security settings is the first step to enable this function runs. This article will help you configure InterVlan routing.

  https://supportforums.Cisco.com/thread/2035882

• Printers Multifunction LaserJet 1536dnf impossible to set up the network in Lion scanning

  Hello

  I'm trying to configure ethernet scanning using my Laserjet 1536dnf. I am able to set up the network in Lion scanning. I was able to do in Snow Leopard. Can someone help me? It would be much appreciated. Thank you

  Hello

  If you have previously installed software, be sure to remove it using the option of the scrubber:

  * Please note that the following steps will delete all HP software installed.

  1. click on menu go (click the desktop, then watch the menu in the bar at the top of the page)
  2. Select Applications
  3 select the Hewlett-Packard folder
  4. double-click on uninstall HP application
  5 follow the uninstall to prompt to select a device to uninstall
  6. press and hold Ctrl + Alt + Cmd keys on the keyboard at the same time as you click on uninstall
  7 approve any prompt to uninstall all HP software.

  Once done, download and install the full functionality of Lion software:

  http://FTP.HP.com/pub/softlib/software12/COL41268/IM-100565-1/HP_Lion_LJ_SW_v12.13.26.dmg

  Make sure to install any update HP available by clicking the Apple icon, then software update

• Impossible to set up the account on the mail application

  I am new to windows 8 and I try to use the app mail mail calendars people trio apart, and am pretty dead on the use rather than other applications. My problem is that my phone is apple so I have an email from icloud I want to put in the icloud app is not available as a type of email, so I select the other option and then select the IMAP type but I can't connect to the server. Please tell me if its possible to add it to the app! I got it to connect with outlook, so I think it should work with this app as well. Help, please! :)

  Hello Megan,

  Thanks for posting your question on the Microsoft community.

  I would like to know some information about the problem so that we can help you better.

  Do you receive an error message or a code when you say, 'I can't it to connect to the server?

  Thank you for details on the issue.

  This behavior can occur if the app files or settings are corrupt or missing.

  I would suggest trying the following methods and check if it helps.

  Method 1:
  Run Troubleshooter app and then try to set up the e-mail account. This tool can automatically identify and fix problems with applications and the Windows store.
  See this link:

  http://download.Microsoft.com/download/F/2/4/F24D0C03-4181-4E5B-A23B-5C3A6B5974E3/apps.diagcab

  If this does not help, use method 2.

  Method 2:
  Please refer to this article and check if it helps.
  Reference:
  Messaging app for Windows
  http://Windows.Microsoft.com/en-us/Windows-8/mail-app-tutorial

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• How to set up the Windows network access program?

  original title: how to set up the N A P

  How to access my windows network access program

  Hi bryan stacy,.
   
  - What version of the operating system are you using?
  -Are you talking about in the center of network share or the network connection folder?
   
  If you are referring to the network connection folder, see the following link for more information:
  Work with the network connections folder

• Impossible to manually add the wireless network

  I need to manually add a wireless network to the laptop. When I click on add in the wireless connection properties window, however there is no pop-up window. If I try on a similar laptop windows wireless network properties appears. The Wireless Auto-Configuration service is started. How can I get the wireless network properties window?

  I was finally able to solve this problem and I posted the results on another forum, I used for this purpose.  Here is the text exactly as I posted on the other forum.  It answers some of your questions.
  Regarding other software that manages the wireless card, Yes, there are (Atheros), he was not managing the adapter (off a long time ago), however, to be sure, I removed it to run in the registry.

  Here is the text of how I solved the problem, I mentioned.  If you have more questions, feel free to post them.

  *****

  I am just posting this here because I could solve the problem and not able to find a reliable source on the internet on a fix for this and for a problem that is the result of my attempts to fix it.

  This is the situation and my landline.

  I was getting this error message

  "Impossible to migrate dependent packages.

  After trying to install a pacakage KB. It did not matter that one but they have been associated with the Wireless settings.

  I continued to try to install the newer packages.
  KB893357
  KB917021
  KB918997

  Each gave me the same message

  "Impossible to migrate dependent packages.

  I read online that I install KB937143 (update IE7) could help.

  I did this and still got the same message on dependent modules.
  I also had another problem occur.
  In the section my network places properties connection wireless adapters, whenever I clicked the Add button / PROPERTIES without window appears to allow me to change the settings, however, I was able to remove items from the preferred networks window.

  My Automatic Configuration Service wireless is running and took Windows to configure my wireless settings.

  I downloaded the updates for my driver Wlan (WiFiHP 500) and I still had the same problems.

  I restarted KB918997 using the/log option and read the log file. This is the last important lines:

  33.849: MigrateHotfix: hotfix migration KB937143
  34.129: migrating QFE KB937143 with command line: update.exe z q - B: sp2qfe
  36.783: failed 1603 Update.exe.
  36.793: MigrateHotfixes: KB937143 Migration failed
  36.793: DoInstallation: Migration failed
  36.933: failed to migrate dependent packages.
  39.597: message displayed to the user: cannot migrate dependent packages.

  I then uninstalled the KB937143 package and reinstalled KB918997 update with the newspaper of Pétion and he went along. I also tested the buttons add and PROPERTIES in the window of Favorites and those networks worked too.

  I checked the logfile KB918997 and he showed this:
  42.311: MigrateHotfix: hotfix migration KB932168 have
  42.511: migrating QFE KB932168 have with the command line: update.exe z q - B: sp2qfe
  88.768: MigrateHotfix: Hotfix KB932168 successfully migrated
  88.768: MigrateHotfixes: return code: 3010
  88.928: DoInstallation: Migration succeeded

  As a side note, I restarted the laptop frequently just to be sure.

  So, really, the option of running with the Ko log file helped me diagnose the problem.

• Need help to choose the correct setting in the virtual network Editor

  This is my first time using machines virtual period. What I do is implementing a laboratory MCSE to follow certain CBT courses, I bought. I created a team of three virtual machines - two of them that are running WIndows Server 2003 and the other WIndows XP. The lab wants to use the following TCP/IP parameters for the three machines (Server1, Server11 and XP1)

  Server1:

  192.168 1,201

  255.255.255.0

  192.168.1.254

  11 server: 192.168.1.211 (same gateway and subnet as Server1)

  XP1: 192.168.1.1 (ditto for the door and the subnet as Server1)

  Primary DNS is set to 192.168.1.201 (Server1 is DNS server).

  Default VMWorkstation allowed me to ping both servers very well without any additional configuration. My problem is when I try to fix the DNS redirector on Server1. Any DNS server IP address that I plug in I could not get my XP box to get out of the Internet. I know it's a problem with my virtual network settings, I'm sure. Problem is I don't know where to start. Can someone point me in the right direction?

  Thank you!

  General things:

  You cannot use the IP address ranges which are used somewhere else, and that the host might be able to see.

  Type ' ipconfig/all' on the host and the glance to the adapter VMnet8. Suppose you see a 192.168.30.1 there. This means that your network VMnet8 address is 192.168.30.0/24 (24 =, displayed subnet mask as 255.255.255.0).

  Your DNS and gateway for virtual systems would be 192.168.30.2.

  You can check this in the editor of virtual network on the NAT tab.

  To change the range of network addresses VMnet8 you must use the virtual network Editor.

  1. go on 'host Virtual Network Mapping.

  2. click on the ">" beside VMnet8 and choose "subnet".

  3. change address you need. It's the network address, so the last digit (in your case!) should be 0. The address range should not be used elsewhere (physical network, VMnet1).

  4. click on 'apply '.

  5. When you click on the ">" again and choose DHCP or NAT you can see that all addresses have been changed accordingly.

  When you enter ' ipconfig/all' to the host, you will see that the VMnet8 host adapter has an IP address of your selected range with 1 node address (e.g. 192.168.1.1).

  The gateway and the DNS so its node address + 1 (192.168.1.2).

  If you found this information useful, please consider awarding points to 'Correct' or 'Useful' responses Thank you!!

  AWo

  VCP / vEXPERT 2009

• Why do block/allow the python network connections?

  Whenever I restart my computer, I get a popup window asking me to deny/allow incoming network connections to python.app. I checked my firewall settings and they are configured to allow incoming network connections. How can I fix so I did not have these messages?

  Create a new account and start in this account. If the problem persists, it may be another application is triggering demand or maybe it's that the firewall application is causing the problem. Function where and how you use your mac OS firewall may not be necessary.

  See the following topics

  http://www.thesafemac.com/do-i-need-a-firewall/

• Base station disappeared after creating the guest network

  After you activate a burst network 2 things happened:

  (1) my original network is always visible, but you can not connect and it does not work.

  (2) all devices of the airport, including the base station have disappeared from the Airport utility.

  I can connect to the network invited near the base unit as expected. As all devices have green LEDs. However, I can't on the main network. And I can't do anything to solve that devices are not visible in the Airport utility.

  Help!

  The 'main' and 'guest' characteristic of network work properly If the right type of modem is used to enable these services.  That would mean a simple modem, as in the example you see just below:

  

  The main and guest feature will not work properly if you have a modem/router, also known as a gateway, as in the example below, which is the type of device that has a number of ISPs providing to their customers.

  

  
  

  Therefore, the first troubleshooting question here would be.. .what type of "modem" you?

  If you don't know what kind of modem you have, please post back with the number of brand and model of the device that you call your modem. (Please do not distribute private information, such as a serial number).

  Next question... base stations AirPort how do you have?

  Finally... to fix things, it may be necessary to connect your Mac directly to each base station by using a wired Ethernet cable... Since Wireless will not provide access to the settings on the airport using AirPort Utility if things are messy. Your Mac has an Ethernet port?