Web interface SG200 problems - 50 p

Similar Questions

• Web interface works is not the well-known address of management

  TLDR:

  • opening webinterface on ip management group-> does not work / ping
  • opening webinterface on eql management ip-> works
  • opening webinterface on ip management group-> suddenly done work
  • Why?

  Yesterday I've updated SanHQ of 2.2 to 3.0.1 to prepare to run the path to upgrade to FW 7.x. Since yesterday, I get the following warning:

  [ID: 1.6] The eql-grp01 group has been added using non well known address (MWKA). Delete and add the group using the well-known address of management of group 172.16.0.9.

  The eql-grp01 group contains a single EQL (eql01 / 172.16.3.15) and has a dedicated management port. The beach is a 16, as such, both the IP and IP management EQL management group are in the same network (again).

  I'm able to reach the Web interface of eql01 on 172.16.3.15 without problems for years. Try to reach the Web interface on 172.16.0.9 has always given problems (timeout, ping works however) until I asked the Web interface on 172.16.3.15, after that, I can reach the Web interface without problems on 172.16.0.9.

  Up until now I did not worth to look into it, but as I'll be add another Member to the group within a few weeks and SanHQ's "tenacious" on do not use well-known management IP address I have tought I might give it a try here, maybe it's the behavior?

  Edit: Adjusted the subject as non-MWKA does not work but the MWKA (submits sugested otherwise)

  OK, you need remove the SANHQ and add in it through the Well Known management address.

  I don't know why he first had to go to the Member port Mgmt vs being able to use the IP alias for group management.

  That's all the management IP address is, like the IP address of the ISCSI discovery.  It is a superior a physical port IP alias.   So if you can reach the Member IP address, you will have no problem reaching the alias.

  Maybe something on your network, or the ARP table has not been updated.

• interface Web for SG200 - 50 p

  I just bought a Cisco SG200 - 50 used p switch. I use it in my house. I'm trying to access the web-based interface to play and manage the switch but I can't do it. I am a novice. I have my router Ethernet connection in the switch. It is plugged into the port 49. I have heaps of other stuff connected to most of the other ports. My problem is that I can't access the interface to the default IP 192.168.1.254. I have the switch to get it to the default factory settings. I restart and power he cycled. No help. I thought that maybe there is a different IP is set by the seller which is not compensation, so I tracert my router and the only IP address that appears is my router. The switch seems to operate them on devices have internet access. Can you please help...

  Hi Pareshraja,

  Check the LED system:

  1. If it's Green stable - the IP address is assigned by the DHCP server or static

  2. If it flashes green - the IP address is 192.168.1.254 default

  The best way to overcome this problem, I guess that would be:

  1. switch to factory default

  2. check if the system LED flashes green

  3. connect PC ONLY with static IP 192.168.1.100 (for example)

  4. access to the web interface of the switch and set the static IP address

  5 firmware update might be the next step, you want to do

  Check out the quick guide that may be helpful:

  http://www.Cisco.com/c/dam/en/us/TD/docs/switches/LAN/csbss/sf20x_sg20x/...

  Kind regards

  Aleksandra

• Problem with IP LRT224 web interface

  I have my LRT224 put in place about a week ago. It works very well for a while, but right now I can only access the web interface through the first LAN. If I use any other LAN and type the IP Address of the gateway on my browser as 10.6.21.1, the address bar will change to 'https://[::ffff:a06:1501]/' instead, and it displays the page Web is not available.

  I don't know in the parameter 'Port management'-> '802. 1 q"all my Device Management are enabled.

  Anyone know what's the problem?

  I found something, when enable https and IPV6, this problem occurs.

• The switch Catalyst 3560 G Web Interface problem

  Hello

  I have a problem with my switch to Cisco Catalyst 3560 G. The web interface does not work (I tried IE11, IE6, Chrome, Firefox, and Safari).

  There is only displayed icons but no text:

  Cisco.jpg

  

  To try to solve the problem, I have updated the switch to its latest version of IOS (from 12.2 (55) to 12.2 SE7 (55) SE9). But the problem persists

  WS-C3560G-48TS 12.2 SE9 (55) C3560-IPBASEK9-M

  In the configuration, the web server is enabled:
  IP http server
  IP http secure server

  What can I do?

  Thank you

  Best regards
  Fabien

  Hello Fabien,

  I think I found the problem and a workaround for this.

  The problem comes from the language of the webbrowser.

  I got exactly the same problem with the same model with the same version of IOS.

  I checked with the debugging tools in firefox and I find the browser want to get (firefox in french for my case) 2 scripts:

  http:///fr/charset.js

  http:///fr/re_preflight.js

  But there isn't any record of en flash: / C3560...

  So I changed the preferred language in firefox (put English first). Reload the Web page and it works very well ;)

  I hope this will help you

  Thank you

  Jeremy

• Unable to access the web interface for SG200-18

  Hello

  I got a new switch and I am trying to connect a UCS.  I ping the switch very well, but when I try to use IE8 or firefox, I can't go to the web interface to configure.

  Here is my configuration:

  Cisco UCS C210 M2

  IP = 192.168.1.100

  Subnet = 255.555.255.0

  Default gateway = 192.168.1.1

  Switch SG200-18

  Default IP = 192.168.1.254 (it is not DHCP)

  Any pointers?

  Tom G

  You need to set a static IP on the PC that is connected to the switch. The IP address of the PC

  must be on the same subnet as the 192.168.1.254.  You may need to try something lower to IE8. Should be

  works with Firefox and IE7. There is also a browser called GreenBrowser which works usually with switches.

  Thank you

  Rick Roe

  Cisco Small Business Support Center

• SLM2048 web interface with firefox 4.0 problem

  Updated Firefox 3.6 to 4.0 and now the slm2048 (firmware 2.0.0.8 & boot 1.0.1) web interface problems. I get the following error message:

  error in Pager.SetpagerHTML String contains an invalid character.

  Specifically, the problem is hyperlink to other ports in the switch port settings is missing. I tried 10 Chrome and IE 8 and the two have even worse problems.

  Someone at - it one reasonable alternative to that roll back to Firefox 3.6?

  David,

  
  

  Actually the GUI for the slm2048 is designed to work with Internet Explorer 5 to 7 and firefox is a little maybe on the GUI.  However, you can use the IEtab 2 addon for firefox.

  
  

  Once installed, you will see an emplem of firefox in the lower right of the Web page.  From there, click on the emblem of firefox and it will turn into an emblem of the internet Explorer.

  
  

  Now you will be emulating explore a Web page in firefox and should not have problems with the GUI.

• Problems with the web interface of connection vcenter 5.1

  Guys,

  What don't understand me, I've set up a new virtual appliance version of vcenter test 5.1, I can connect just fine using vsphere client and console, but the web interface refuses to agree with the same identifiers. What is happening with this single sign? I really do not understand.

  You guys could help me please?

  I stumbled upon this same question.  5.1 with the search service is completely different than 5.0, this is why the others are not working.

  Here's what I did to solve the problem.  I turned on the regeneration of SSL certificate:

  1. Navigate to https://[IP]: 5480 and connect
  2. Go to the Admin tab and press the button "Toggle the setting of certification" until activated regeneration 'certificate' displays Yes
  3. Go to the network tab and change the host name.  This will trigger a regeneration of SSL (or you can change the ip address).  I don't know if change 'localhost' to something else helped, but it can't hurt.
  4. Restart the box (restart System tab button.)

  At this point, you can look at the start-up of the machine of vcenter console messages.  You will notice some messages about detection of a new hostname or IP and regenerate a new certificate.  You will see all the services to import it again SSL ceritifcates so.

  At the end of the reset, I was able to connect to the web client to vCenter!

  HTH

• LaserJet 4000: HP LaserJet 4000 web interface problems

  I have an HP LaserJet 4000 very old but still very functional.  When I try remotely inside through the web interface to change settings, the screen does not load correctly.

  It wants to load a JAVA runtime and I have the latest version of loaded oracle, but there must be an incompatibility.  I think that it only works with a very old runtime.  I have tried with different browsers such as firefox and chrome, but the result is much the same.

  Y at - it solution or a firmware update or something to fix this?

  You have the 600n jet direct card and the issues are known.  I think that windows 95 was the last os that could communicate and give you the web page.  You could try to download the latest firmware for your jet direct card and update its firmware using hp download managere, but to be honest I don't think it will work.  The saving grace is that you can make any changes you want in the control panel of the printer.  Just navigate the EIO menu on the printer and go through the menus.  A little more difficult, but it can be done.  Good luck.

• GS752TP - Slow Web Interface

  Does anyone else have this problem? The web interface is so slow to become almost unusable. It loads the background then hangs just for a good 20-30 seconds. Sometimes, it loads the buttons... sometimes it is just with a white background. When I get to enter the interface by clicking on a button sometimes loads data... sometimes it is just there and I have to close the browser and start over? Someone at - it suggestions? It runs later (and also the initial firmware).

  -Eric

  I had this same problem for a while.

  As a "fix"------"Workaround"------"bodge" I used the Portable Firefox 3.5.6 put up-to-date of changes to VLAN\LAG settings.

  Really, it's not perfect, but works.

  /Pokes Netgear with a big pointy stick!

• jumble of text in the web interface after Web Services update / firmware

  I received a message on the screen of my Officejet 6700:

  Update recommended

  An update is available for Web Services (ePrint and Apps).

  Do you want?

  I chose to update now and it installed fine, or so I thought.

  I checked the web interface of the printer, and there is a bunch of text confused, as the code is messed up for the web server.

  I had just finished to check the status of your ink cartridges (and subsequently replaced a), so I have the fully functional Web page fortunately still open on another machine, so I can tell exactly what is forward - after on this page.

  On the tools > gauge of ink page, on the right page (old) the said table (title, first line, first column):

  Cartridges installed

  Color | Magenta | Cyan | Yellow | Black

  Part number

  Type

  End of warranty date (A-M-J)

  First Installation Date (A-M-J)

  Area of ink

  USE

  HP

  But after the software update, it says this:

  Print the self-test Page

  L@S#0456 | Number of recorded events. L@S#0462 | L@S#0552 | L@S#0450

  Use of the accumulated media

  Date

  L@S#0477

  L@S#0561

  L@S#3345

  In addition, the order "supplies" link, with a contextual text of "print order supply."

  now, says "Cartridge", with a contextual text ' block unwanted faxes '

  And "Print Printer Status Report" now says "L@S#2567".

  I went to the support section and found an update firmware, but during download and execution, after you find the printer, he says that he is already up to date and leaves me not choosing to try and reapply the update of the firmware (as is obviously what is happening through the touchscreen menu has already done).

  Should I just restore to factory settings? I think that firmware would not be changed by doing this. It is not an older version of the firmware available on the product support page, to return to an earlier version.

  Via the screen menu touch printer, a Printer Status Report print indicates the firmware version is MPM3CN1322DR.

  How to force a reinstallation of the firmware, or let them difficulty firmware which was released on 25-06 - 2013?

  I've been using Google Chrome and even had 2 tabs open in the same window, one from before the update and the second I opened after the update, so this was not a factor.
  
  I had not revisited the web interface of the printer to date, and currently, I see that the problem has disappeared!
  The version of the firmware has not changed, and I did no manipulation of the printer. I also highly doubt that the main user has nothing, because it is not tech savvy. So, the problem seems to have corrected itself.

  The only thing I see now, that I did not notice before, is that there is a version of firmware fix, but it currently says 0. I don't know what it was before, but I guess zero means that there is a patch, so the firmware didn't automatically update in order to make the problem disappears.

  Problem disappeared, but I don't know how or why. I haven't decided if I will update the second printer that is the same model.

• Integrate the ICB with web interface

  Hi all

  We already have a CVI writes to order any of our instruments. We must develop a web interface to pass parameters to the CVI. In addition, currently the data is generated by the BCI as .csv files. What more we need to do is to transfer the data to a database as well. I did some research and discovered that Measurement Studio provides a .NET environment to control instruments. In addition, I think that the CVI/SQL Toolbox should be able to solve my problem of database. My question is who will Measurement Studio I want to integrate the CVI already present and communicate with him using a web interface? If so, what me does establish this communication?

  Thank you

  Kanu

  Kanu,

  Unfortunately, there is no easy or good way to create a web interface with CVI directly.  You can do this in Visual Studio with Measurement Studio, but you will at least need to the professional edition to do because you want to use web forms.  There are some resources with more information on the web forms, including this Walkthrough.

  Since you already have an investment in CVI, I don't understand why you don't want to throw just as work on.  According to the works of your code, you have a few options on how you try to bring together these two languages.  You can try to make your C code in a DLL and call it in the .NET application, as in this discussion of the call to invoke from managed code.  However, a better solution would probably be to use Of network Variables to communicate between the two programs.  Then, you can limit the .NET application to be mostly just a control interface that writes to the network variables, which are then used in the CVI program that you've already written.

  Hope this helps,

  Jen W

  Technical sales engineer

  National Instruments

  NI.com/support

• SRW2016 Web Interface after Firmware Update error

  I have a new SRW2016 and after updating from 1.2.1 to 1.2.2 firmware I get an error trying to connect.  I use Firefox with IETab and the error message is:

  ... An error has occurred.

  ... You want to debug?

  ... Line 11

  ... Error: "tBodies' is null or not an object

  I tried to use Internet Explorer, but the status bar displays "error on page".

  I * really * need help!  Any ideas?

  BTW, I got the update of the firmware twice.  The first time was

  minutes and finally he stopped (I don't remember if there was a mistake

  message).  The second update seemed ends without problems.

  TIA

  Well, I was about to do the update with hypertermial/xmodem, when I thought I should check the browser interface.  And now, it's working now (even if it's really slow).

  He had to because of my recent update to Firefox v2 to v3, as well as the updated IE Tab addon.

  I hope that the web interface used the HTML standards and not require IE. It's very frustrating.

• WVC54GCA Missing WPA/WPA2 security in the web interface options

  I just had a WVC54GCA and discovered that there are some missing configuration options in wireless settings:

  On the web interface of cameras:

  Web interface > base: Wireless Settings > [modify security settings] > Security Mode:

  the drop-down list gives me two options: Disable WEP, but not WPA, WPA2.

  I've upgraded to the latest firmware (1.1.00 build 02), but the problem remains.

  Tried different browsers (Firefox 3.5, IE8) with the same result.

  Is this a bug in the firmware?  A defective unit? Anyone else having the same problem?

  Try to reset your IE browser settings and then try to connect to your camera configuration page and check if you are able to find that the options... If it is still impossible to find the WPA/WPA2 Option on your camera, press and hold the reset button for 60 seconds... Release the reset button... Unplug the power cable from your camera, wait 60 seconds and reconnect the power cable...

  Now check if you are able to find that the options... If still no so I think this could be the problem with the camera...  I think that you need to replace your camera.

• EA2700 - unable to return to the old Web Interface

  Hello

  I have an EA2700 that I am moving back to the old interface, however it error whenever I try to install the firmware.

  That's all that I always get this message:

  Unexpected error that the firmware update has failed. Please try again later.

  We encountered an unexpected error. If the problem persists, please visit our Technical Support site.

  I have reset the router several times, he turns off all night, re-uploaded the file several times and I am still unable to restore successfully. Sometimes she same error when I try to set the password of the router itself and I have to reset it again before I can use the interface.

  Was setup to give than to try, and Oh surprise when I connected to my router this time I was introduced to the classic web interface

  Among the updates of the firmware Failed must have actually managed, even if he just kept throwing error messages. To be sure, I re-flashed the old firmware from inside the classic interface and it worked perfectly without errors.

  At least I am now finally back to where I was before the clouds rolled in.