interface Web for SG200 - 50 p

Similar Questions

• Could not load the interface Web VMware Server 2

  Hello

  It seems that there have been a number of users has a problem similar to mine. Unfortunately so far it seems not be an easy fix. A few weeks ago, I downloaded VMware Server 2.0.2 and installed on my Ubuntu 8.04 Server. Surprisingly, it worked very well and I set up a virtual machine via the web interface. It took 3 weeks later I started having problems. Or, when I tried to access the web interface through the browser page just came not upward or it came I have connected, but then was then put on the door.

  Initially, I have done the following but doesn't seem to help.

  -Reboot the system

  -Restart all vmware services

  -Delete all cookies and cache.

  Then I thought that this question had to do with the process of webaccess. It seems that the process was not because for a very short period of time, the connection appeared and I was able to connect. But after a short period of time, it displays an error and then the connection was unreachable again.

  I checked the port 8308 below:

  netstat - LNP | grep: 8308

  TCP 0 0 0.0.0.0:8308 0.0.0.0: * LISTEN 5754/webAccess

  Here is the response from audit ipv6:

  netstat - LNP | grep tcp6

  ping6-c1 localhost

  Unknown host

  I disabled it by changing of ipv6 on off in the etc/modprobe.d/aliases.

  My hosts file resembles the following:

  127.0.0.1 localhost

  127.0.1.1 web web.cinci.rr.com

  The following lines are desirable for the hosts with IPv6 support

  : 1 localhost ip6 ip6-loopback

  FE00::0 ip6-localnet

  FF00::0 ip6-mcastprefix

  FF02::1 ip6-allnodes

  FF02::2 ip6-allrouters

  FF02::3 ip6-allhosts

  I have attached the file proxy.log. I saw a few exceptions so don't know if this has to do with the problem.

  Also, I've included the hostd.log (it's in a zip archive because there are a few files of newspapers spend). I have

  Finally, I checked all the active internet connections and sockets. The results are below:

  Connections Internet active (only servers)

  Name of Proto Recv-Q Send-Q address foreign address State PID/program Local

  TCP 0 0 127.0.0.1:8005 0.0.0.0: * LISTEN 6910/webAccess

  TCP 0 0 0.0.0.0:902 0.0.0.0: * LISTEN 6888/vmware-authdla

  TCP 0 0 0.0.0.0:8009 0.0.0.0: * LISTEN 6910/webAccess

  TCP 0 0 0.0.0.0:8333 0.0.0.0: * LISTEN 6994/vmware-pass

  TCP 0 0 0.0.0.0:80 0.0.0.0: * LISTEN 4917/apache2

  TCP 0 0 127.0.0.1:8307 0.0.0.0: * LISTEN 6994/vmware-pass

  TCP 0 0 0.0.0.0:8308 0.0.0.0: * LISTEN 6910/webAccess

  TCP 0 0 0.0.0.0:23 0.0.0.0: * LISTEN 4421/sshd

  TCP 0 0 0.0.0.0:443 0.0.0.0: * LISTEN 4917/apache2

  TCP 0 0 0.0.0.0:8222 0.0.0.0: * LISTEN 6994/vmware-pass

  UDP 0 0 0.0.0.0:68 0.0.0.0: * 4393/dhclient3

  brute 0 0 0.0.0.0:1 0.0.0.0: * 7 6634/vmnet-natd(8)

  UNIX domain sockets active (only servers)

  Proto RefCnt flags Type State I-node PID/name path of the program

  UNIX 2 BDRM STREAM LISTEN 16158 6994/vmware-pass/var/run/vmware/root_0/1267514173386057_6994/ha-nfc-fd

  UNIX 2 BDRM STREAM LISTEN 16165 6994/vmware-pass/var/run/vmware/root_0/1267514173386057_6994/ha-nfcssl-fd

  UNIX 2 BDRM STREAM LISTEN 16167 6994/vmware-pass/var/run/vmware/proxy-Web server

  UNIX 2 BDRM STREAM LISTEN 16189 6994/vmware-pass/var/run/vmware/root_0/1267514173386057_6994/hostd-vmdb-fd

  UNIX 2 BDRM STREAM LISTEN 16191 6994/vmware-pass/var/run/vmware/proxy-mob

  UNIX 2 BDRM STREAM LISTEN 15714 6634/vmnet-natd(8) /var/run/vmnat.6634

  UNIX 2 BDRM STREAM LISTEN 11895 4940/python /var/run/fail2ban/fail2ban.sock

  Finally, just to try to "start over". I removed VMware Server system and reinstalled. Since the virtual machine is in a separate Directory I thought I had nothing to lose. Removal and resettlement seem to succeed. After a reboot and an attempt to access the interface web it STILL didn't work. I'm really at a loss right now. Any help would be much appreciated.

  Thank you

  Aaron

  Hello

  Welcome to

  Don't forget to give my answer. It is the way to give users of vmware communities who helps others.

  Best wishes / Saludos.

  Pablo

  Please consider providing any useful answer. Thank you!! - Por favor considered premiar las useful responses. ¡¡MUCHAS gracias!

  Virtually noob blog

• I get a JavaScript Application error: "setTimeout" called on an object that does not implement the interface Window for Firefox.

  I get a pop up box with the message: Application JavaScript error: "setTimeout" called on an object that does not implement the interface Window for Firefox.

  But it seems to appear when I go to Amazon.com. Then he opens with this message and the OK option? But as fast as I can click OK, another box appears. After all a half dozen, she disappears - until what I move to another part of Amazon! I uninstalled - reinstalled and then - Firefox and BA. I do not understand this!

  (And of course, there is always the possibility that it is not only attacking me on Amazon... There may be a lot of other sites that also trigger, and I just haven't been there yet.)

  Hello

  Try Firefox Safe mode to see if the problem goes away. Firefox Safe mode is a troubleshooting mode that temporarily disables hardware acceleration, restores some settings and disables add-ons (extensions and themes).

  If Firefox is open, you can restart Firefox Safe mode in the Help menu:

  • In Firefox 29,0 and above, click on the menu button

    

    click Help

    

    then select restart with disabled modules.

  • In previous versions of Firefox, click on the Firefox button in the upper left of the Firefox window and click help (or click on help in the Menu bar, if you do not have a Firefox button) and click on restart with disabled modules.

  If Firefox is not running, you can start Firefox in Mode safe mode as follows:

  • On Windows: Hold down the SHIFT key when you open the desktop Firefox or shortcut in the start menu.
  • On Mac: Hold the option key during the startup of Firefox.
  • On Linux: Exit Firefox, go to your Terminal and run firefox-safe-mode
    (you may need to specify the installation path of Firefox for example/usr/lib/firefox)

  When the Firefox Safe Mode window appears, select "start mode safe."

  

  If the problem is not present in Firefox Safe Mode, your problem is probably caused by an extension, theme or hardware acceleration. Please follow the steps described in the section Troubleshooting extensions, themes and problems of hardware acceleration to resolve common Firefox problems to find the cause.

  To exit safe mode of Firefox, simply close Firefox and wait a few seconds before you open Firefox for normal use again.

  When find you what is causing your problems, please let us know. This might help others with the same problem.

• When I type in a search on the web for anything whether it's IE, eBay or Facebook my PC just redirects research and opens another page, how can I rectify this

  Original title: redirection

  When I type in a search on the web for anything whether it's IE, eBay or Facebook my PC just redirects research and opens another page, how can I rectify this

  Hi Mark,
  Your computer is probably infected by a virus. Try following the steps in this virus/malware removal guide: http://www.selectrealsecurity.com/malware-removal-guide
  It contains instructions which will remove most malware infections. If you have any questions, just ask me. I hope this helps you.
  Brian

• I bought Lightroom 3 and installed on my MacBook Pro via a disk. Later, I upgraded via web for Lightroom 5. My question is how can I install a copy of Lightroom 5 on my new iMac?

  I bought Lightroom 3 and installed on my MacBook Pro via a disk. Later, I upgraded via web for Lightroom 5. My question is how can I install a copy of Lightroom 5 on my new iMac?

  Download, install and activate...

  Lightroom - all versions

  Windows

  http://www.Adobe.com/support/downloads/product.jsp?product=113&platform=Windows

  Mac

  http://www.Adobe.com/support/downloads/product.jsp?product=113&platform=Macintosh

• Insert data to tabe in interface web oracle

  Hello.
  I created and inserted the data from my database using SQL more.
  all tables created sucsefully and I can see them YES.
  but all rows in tables shown empety (this means under the lines, the column is empety not 0).
  
  now how to check the data that I inserted in the tables? I can see them in YES? (web interface)

  is not anyway to see the data in the web interface (web console in EM)?

  Don't know what your problem is... in EM you choose schema tab, in "Data objects" you select Tables, and then select a schema, and you can see the list of tables: you choose a table and in Actions, you choose 'view data '. It does not work?

• Unable to access the web interface for SG200-18

  Hello

  I got a new switch and I am trying to connect a UCS.  I ping the switch very well, but when I try to use IE8 or firefox, I can't go to the web interface to configure.

  Here is my configuration:

  Cisco UCS C210 M2

  IP = 192.168.1.100

  Subnet = 255.555.255.0

  Default gateway = 192.168.1.1

  Switch SG200-18

  Default IP = 192.168.1.254 (it is not DHCP)

  Any pointers?

  Tom G

  You need to set a static IP on the PC that is connected to the switch. The IP address of the PC

  must be on the same subnet as the 192.168.1.254.  You may need to try something lower to IE8. Should be

  works with Firefox and IE7. There is also a browser called GreenBrowser which works usually with switches.

  Thank you

  Rick Roe

  Cisco Small Business Support Center

• GANYMEDE conf for interface web aironet 1100

  Hello

  I have configured our access point for Ganymede and his works fine, but I still want one thing, web user interface & pass must use Ganymede.

  How can I do this?

  Thank you

  Hello

  I use a 1200, but maybe it helps.

  Via the Web Interface, I can navigate to SECURITY > Access Admin and turn on an option called "authentication server if not found in local list". After having turned it on, I can use my username and password for the Web Interface and in the Telnet program.

• Update firmware of Web for failure to GS108Ev3

  I have money to upgrade to version 2.00.05 but do not have a very practical Windows machine. So I thought I would use the web interface.

  After entering the "loader" on the switch mode, I downloaded the firmware, only to find the router stuck in this mode charger with no way out.

  I tried:

  * reset

  * power off/power on

  * held reset for > 1 min (no effect at all).

  What I do, I will never return to the screen of the firmware loader. I saw a similar question for an earlier version (https://community.netgear.com/t5/Managed-Switches/GS108E-Firmware-Upgrade-Issues/td-p/372672) that was solved by using TFTP to download the firmware. That doesn't seem to work in my case.

  Ideas, or I need to get my hands on a Windows machine and try the utility?

  And an update: managed to borrow a Windows machine. The ProSafe (latest version) utility did not find even the switch. Nice!

  Then I tried upgrading the firmware of the chrome on the windows machine, and voila, that actually worked! What on earth could be the problem?

  So, to summarize: firmware upgrade of chrome or firefox on linux failed, Prosafe utility has not detected switch, Chrome on Windows, saved the day.

  I'm more confused as I was when entering.

• LaserJet p1102w: how to access the interface web printer with new router

  I just bought a new wireless router, hoping that I'll be able to more easily print with my p1102w.

  Internet access works ok desktop and laptop (wireless).

  However, I had bookmarked the IP address of my printer, and before, I've always been able to access it by clicking on the bookmark. I checked the range of IP addresses for the router, and the IP of the printer is outside this range, so I don't know why I am no longer able to access to this. I can't access the web interface, whether they come from my laptop or desktop (wired). However, the printer is capable of printing from the desktop without problem.

  How do I enter this? I would like to restart the configuration wireless configuration, but I thought I needed the web interface for this.

  I should just insert the CD? I made a tweak or two and would prefer to keep all the settings of the printer even if I can, but I can start all over again if I have to.

  
  HP LaserJet p1102w

  I just deleted the printer on my laptop computer, reset the settings of the printer default and then run Setup from the wired desktop wireless utility wireless. Seems to have worked, I can now access the web interface via my laptop now.

• Interface Web of SGE2000 does not

  Get a blank screen in the two settings of the web interface when you are connected. Cannot know why it will not load.

  SW worm 3.0.0.18

  Start: 2.0.0.03

  HW Ver: 00.00.01

  Have tried to use the easy upgrade tool and get a caveat: not found device information. Application will end.

  Step 1: trying to open the telnet connection...
  Information STEP1:Gathering
  show the system - control of result for «show system unit 1-2»
  Step1:type:
  Step1:OID: 1.3.6.1.4.1.9.6.1.72.2000.2
  Step1:sys name: company
  Step1:location: Salledeserveurs.com
  Step1:sys Contct: IT
  Step1:MAC - address: f0:25:72:89:9e:e2

  Has anyone experience this problem? Any ideas how to fix?

  Salvation of parking, if the GUI does not load, please try the following:

  The same computer using IE, Firefox, Chrome, etc.

  Another computer with the mentioned browsers (preferably Windows 7 or more)

  If none of these works, try the plant selector as it seems that the software is hooked

• interface web cisco ip phone from the computer LAN

  Hello

  On the uc540 the DATA VLAN is en 192.168.10.0 as the VLAN DATA it is en en 10.1.1.0, I want to access them from the local network the computer the my client who is en 192.168.0.0 to web interfaces of the cisco ip phone so by going to http://10.1.1.x without needing to modifier already exists, how can this be done? I have available in my not to a manageable switch that would allow me to integrate the lan that does not exist in the DATA VLAN of the CPU.

  Thanks for advance

  Hello

  The voice VLAN 10.1.1.0 is not routed in your network.

  Namely that workstations do not know that there is, and this due to the fact that their router default doesn't know not router network.

  Here's how to fix that little problem of routing:

  1 / if the default router for the positions in the VLAN data isn't the UC 500, just to add a static route in this router with the sub network 10.1.1.0 and address of next hop (IP address of the router that helps you achieve this subnet).

  For example: If the default router is a Cisco router, it is in the VLAN data with the UC500 and the UC500a as the IP address 192.168.0.1.

  conf term

  !

  Route IP 10.1.1.0 255.255.255.0 192.168.0.1

  !

  end

  2 / if we can't change this router by default, we must add a path in given work stations of the VLAN.

  In a post Windows you do that in a CMD window with the ROUTE ADD command

  c:\>route add 10.1.1.0 mask 255.255.255.0 192.168.0.1

  and you can check your local routing table with the command

  c:\>route print

  If you want that this road remains in positions of work even after a reboot, use option-p of the route command added

  c:\>route add 10.1.1.0 mask 255.255.255.0 192.168.0.1 Pei

  Control the Access-list!  : Of course, after having solved the problems of routing, assure you that there is not an access list that blocks traffic

  FINISH POUR a bit of security.  Allow access to the VLAN voice is not a good practice!

  As long as possible, to avoid to make the voice VLAN too accessible from anywhere. Therefore, a good practice is to not allow the VLAN data access to the VLAN voice.

  Patrick

• Passage of thanks VM SATA drives? (update: a bug in the user interface web host)

  I use ESXi 6.0 for private home use and am currently building a NAS with him (on top of ESXi OpenMediaVault). However, as I am using only material quality consumer, my SATA controller does normally not for raw device mapping. I added the raw device manually in accordance with VMware KB: Raw Device Mapping for the local storage but when I try to join the top device (via the file on the local data store) a virtual machine, the user interface gives me an error message indicating that the capacity is too large for the given data store (of course, the system disk is much smaller than the data disks).

  Is there a way I can still add raw devices to virtual machines?

  Another update: upgrading the client to the web user interface host to 3731936 seems to fix this problem. I can now add virtual disks as RDMs in the web client.

• VMWARE Server 2 and Red Hat 5.4 Interface Web ES crashes

  I have been using VMWare Server 2.0.1 fine several months until I've restarted my server in a new kernel.

  Although all modules start OK in the window of the terminal web interface seems to hang after have been up for a few seconds only - sometimes barely enough to open a session.

  Any ideas?

  My hardware is Dell R900 - 4 image intel CPU with 128 GB of ram

  My OS is Red Hat Linux ES version 2.6.18 kernel - 128.2.1.el5

  Thank you

  I came across the same issue last week. This is the background I and fix that made me backup for now.

  It seems that vmware provides their own libraries for some of what they need and that there may be a bad interaction between that and RHEL 5.4 libraries updated.

  The FIX:

  yum downgrade glibc glibc-common

  Delete it / come back about 22 packages/dependencies. Then I restarted and re - represented vmware-config and functions of each thing. Note You must change your configuration of yum update so that it is not pushing the new glibc glibc-common until this problem gets solved official.

• How to access the interface web web services test

  I'm running my server 10.3 in test mode. How can I access the web test for my web service interface?
  I can see the wsdl, but I can't access the test interface as in previous versions.
  
  Thank you

  Click in the table of your Web Service deployment.

  Scroll down to the section modules and components. Here, you should see a tree that contains Web Services.

  Click your web service

  Click on the test tab

  Open the tree and here, you should see the link to test client.

  If you have the location of the WSDL file, you can also add: http://adminserverhostname:7001 / wls_utc /? wsdlUrl = forward, for example,

  http://adminserverhostname:7001/wls_utc/?wsdlUrl=http://serverhostname:port/CompanyWebService/CompanyService?WSDL
  

  in what http://serverhostname:port/CompanyWebService/CompanyService? WSDL is the location of the WSDL file