what current can run off a USB - 6009 DIO? (part 2)

Similar Questions

• What is input equivalent circuit of USB 6009 PFI0

  The entry USB-6009 PFI0 is the same the analog input circuit stated in manual mode?

  I use the PFI0 to trigger a measurement of voltage and it works a lot using a HP function generator.

  When I try to drive the low entrance with my circuit looks like there's a pull up resistance to + 5 on the entry of PFI0 terminal.
  This entry PFI0 will accept an output of comparitor from 0 to 15 volts with being damaged?

  Kip

  Here is my solution to operate the PFI0 TTL digital input using a CMOS comparator.

  I use a 2N4401 npn transistor.

  Connect the transmitter to the ground terminal.

  Connect the manifold to the PFI0 (there is a pull-up internal resistance to the 6009).

  To connect to the Base of a voltage divider that limits in input current and decreases the CMOS voltage to TTL levels.

  In my case I'm going to 0 to + 15 so my voltage divider is 4.7 k and 2.2 kohm to fall to 0-5 volts.

  It is an Inverter circuit so your sense of trigger will go head on falling edge, or vice versa.

  I hope this helps someone.

  Kip

• What is the MTBF for the USB-6009 case

  What is the average time between failures (MTBF) for the USB-6009 case?

  Hello

  Unfortunately, there is no available for the USB-6009 case MTBF.  In order to retrieve this information, there is a cost for our R & D department.  If you need this number, please contact your local representative OR or open a service request to ni.com/ask.

  I apologize for the inconvenience.

• I can't get the "Disk Cleanup" to work, I can run off frag etc., but not the cleaning disc of any idea? __regards__Ian

  The hourglass does not appear when I click on disk cleanup function. I closed and started in safe mode, but still no luck. I can't put my Windows disc to try to do a repair that I loaded SP3 and my version of disc is only SP2.
  Thank you
  INA

  Click Start, run. Type the following command and press ENTER:

  regsvr32 dataclen.dll

  Try to open disk cleanup (cleanmgr.exe) now. Ramesh Srinivasan, Microsoft MVP [Windows Desktop Experience]

• Can't find USB-6009 simulated in list

  In automation solutions Explorer, when I try to create a new OR-DAQmx simulated device, I can't find the USB-6009 case. Looks like it would be under the heading USB - DAQ, but all that's there is the 9000 series devices. The 6000 series are not available as devices of simulations?

  Tim

  Hi Jordan,.

  Box USB-6211 is actually a M Series family.  Expand the M series: DAQ when creating your device simulated, then scroll down to the list of USB devices.  Hope this helps!

  

• temperature sensor with the acquisition of data usb-6009

  Greeting

  I want to use a sensor with usb-6009 to save the variation of body temperature about 15 minutes and then use these data in labview.

  If you please you can advise me with the best low-cost use and the way/circuit sensor connect it to the usb-6009.

  Hi ba7soun,

  If you can use with USB-6009 LM35 depends on the range of output voltage of the sensor. I understand that it requires a 5V supply with respect to the ground, which you can provide to the USB-6009 (more than 200 my should not come from the USB-6009).

  The maximum range of the USB-6009 is - 10V to + 10V, while the minimum range is - 1V to + 1V, also probably the output signal of the LM35 will be in this range. What you need to do is to compare the full range of the output signal with the range of the DAQ divided by 2exp (14) (because it is a 14 bit ADC) and ensure that the first is much more than the latter.

  Kind regards

  Condette Dhruv.

• How to find liability that can run a specific report

  I would like to know how to find what responsibilities can run a specific report.
  
  Is there a was to do later in 11i app? or y at - it a specfic query I can run?
  
  Any help would be appreciated.

  Hello.

  Check if this request meets your needs:

  SELECT r.responsibility_name, g.request_group_name, cp.user_concurrent_program_name
  OF fnd_responsibility_vl r, fnd_request_groups g, fnd_request_group_units rg fnd_concurrent_programs_vl cp
  WHERE r.request_group_id = g.request_group_id
  AND rg.request_group_id = g.request_group_id
  AND rg.request_unit_id = cp.concurrent_program_id
  AND rg.application_id =
  AND r.responsibility_name = '. '

  Hope this helps,

  Octavio

• OR USB-6009 can produce the constant current source/sink?

  Hi all

  I have a card NI USB DAQ to 6009. I need a battery for constant (charge/discharge current<1mA) and="" simultaneously="" monitor="" its="">

  I was wondering if I can use USB-6009 of output constant source/sink of charge/discharge current the battery? I've seen a few threads that says 6009 impossible to output constant son of currents, but other says we can use the digital output to provide the current, but it was not only described how.

  Thank you.

  All the outputs of the USB-6009 case are sources of tension and all have current limits low. There is no way to generate outputs current controlled directly from this device.

  What I would do (and have done) is to build circuits of external current source/sink with an op amp or a transistor and allows you to enable or disable a digital output of the USB-6009. If the current must be adjustable, use an op amp circuit that takes an input of the analog output of the USB-6009 voltage to set the current.  Use an analog input channel to monitor the battery voltage.

  Lynn

• What version of Firefox options do I have to use Firefox on the new laptop running Win 7 64 bit, and how do I move bookmarks current laptop running Firefox 3.5.13 again laptop?

  Currently running on the laptop using Windows XP pro sp3 Firefox 3.5.13 and want to move my favorites to a new laptop. New laptop using Win 7 pro 64 - bit OS. I've read too many conflicting reports on Firefox and Win 7 and Firefox works on a real 64 - bit version. What are my choices for a stable browser for the new laptop and what specific version of Firefox is recommended, and the advantages and disadvantages of this suggestion? (I think we can run Firefox 32-bit version in the 64-bit environment, but which is the best choice?) I have not installed Firefox on the new laptop yet and am eager to dump IE. It is displayed for my old laptop. Thank you...

  Mozilla working on a 64-bit version of Firefox, but it's a way off. Currently, the only release versions are 32-bit, and the next major version will be also only 32 bits.

  I recommend that you install the latest version of publication (3.6.10) available since http://www.mozilla.com/

  To copy bookmarks, follow the procedure described in the article restore bookmarks from a backup or move them to another computer to save a json file, you can import (restore) on the new laptop. You can copy more bookmarks, for details, see back up and restore the information contained in the Firefox profiles and backup - MozillaZine Knowledge Base Profile. The last link includes a third-party utility that can make the process easier.

• My Apple Macbook late 2009 has been upgraded to 4 GB and Mountain Lion but runs very slowly. When I check the memory system activity monitor, I see that there are 1.6 GB inactive. Is this the cause of the slowness and what I can do?

  My Apple Macbook late 2009 has been upgraded to 4 GB and Mountain Lion but runs very slowly. When I check the memory system activity monitor, I see that there are 1.6 GB inactive. Is this the cause of the slowness and what I can do?

  Reinstall OS X from scratch and add more RAM.

  Ways to help make a slow Mac faster

  17 reasons why your Mac runs slower than expected

  Slow performance of Mac? This Article addresses!

  Difficulty of slow start in OS X | MacFixIt - CNET Reviews

  6 easy tips to speed up OS X Yosemite on your Mac.

  Avoid using third-party software that claims to clean your computer. This software does more harm than good. In addition, you don't need it. Note that all computers become slower over time even in the normal conditions of use. Generally, the experienced users erasing the hard drive and do a clean install from scratch at least once a year or every time that the installation of a major upgrade of the OS. Well sure doing so also means that you need to maintain regular and several backups.

  Add more RAM or reduce the number of simultaneously executed from applications and utilities. Remove unnecessary software such as anti-malware and that promises to clean your Mac. Look for the runaway process: Runaway applications can shorten the battery life, affect performance and increase the heat and fan acti... See also:

  Before Mavericks

  Open the activity monitor in the Utilities folder.  Select all processes in the drop process .  Click the % CPU column heading twice to display in descending order.  If find you a process that uses a large amount of time processor (> = 70,) then select the process, and then click the quit icon in the toolbar.  Click the force quit button to kill the process.  See if that helps.  Don't forget to mention the name of the runaway process, so you can find the cause of the problem.

  Mavericks and later versions

  Open the activity monitor in the Utilities folder.  Select all processes in the menu display .  Click the CPU tab in the toolbar. Click the % CPU column heading twice to display in descending order.  If you find a process that uses a large amount of CPU %, then select the process, then click on the quit icon in the toolbar.  Click the force quit button to kill the process.  See if that helps.  Don't forget to mention the name of the runaway process, so you can find the cause of the problem.

  Things you can do to solve the slow Downs

  If your computer seems to run slower, here are some things you can do:

  Start with tours: OS X maintenance - MacAttorney;

  The X Lab: the X-frequently asked questions.

  " Safe mac" Mac Performance Guide;

  " Safe mac" the myth of the dirty Mac;

  Maintenance fast Mac Help.

  Start in Safe Mode , and then repair your hard disk and permissions:

  Fix the hard disk and permissions before Lion

  Boot from your OS X install disk. After the installer loads, choose your language and click on the button continue. When the menu bar appears select utility drive in the Utilities menu. After that the charges of THE select your entry from hard drive (mfgr. ID and car size) in the list on the left.  In the status area, you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is faulty or has failed. (State SMART is not reported on external drives Firewire or USB). If the drive is "verified", then select your OS X volume in the list on the left (subentries under the entry for the road), click the first aid tab, then click the repair disk button. If THE reports any errors that have been corrected, and then run repair disk again until no errors are reported. If no errors are reported, click repair permissions. Wait until the operation is complete, then exit FROM and return to the installer.

  Repair the hard drive - Lion-Lion/mountain/Mavericks

  HD recovery start:

  Restart the computer and after the buzzer, press on and hold down the COMMAND and R until it appears the screen of Menu utilities. Otherwise, restart the computer and after the buzzer, press on and hold down the OPTION key until the Boot Manager screen. Select recovery HD disk icon and click on the button below.

  When the recovery menu appears, select disk utility. After that the charges of THE select your entry from hard drive (mfgr. ID and car size) in the list on the left.  In the status area, you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is faulty or has failed. (State SMART is not reported on external drives Firewire or USB). If the drive is "verified", then select your OS X volume in the list on the left (subentries under the entry for the road), click the first aid tab, then click the repair disk button. If THE reports any errors that have been corrected, and then run repair disk again until no errors are reported. If no error is not reported, then click repair permissions. Wait until the operation is complete, then exit FROM and return to the main menu. Select restart from the Apple menu.

  Restart your computer normally and see if it helped at all. Then do little maintenance:

  For disk utility can't handle situations, the best third party is Disk Warriorutility;  Fixed DW only for problems with the disk directory, but most disk problems are caused by the corruption of directory; Warrior drive 4.x is now compatible with Intel Mac.

  Note: Alsoft ships DW on a bootable DVD that will boot Mac running Snow Leopard or earlier. He cannot start Mac that came with Lion or later preinstalled, however, DW will work on these models.

  Suggestions for OS X maintenance

  OS X performs certain maintenance functions that are supposed to take place on a daily, weekly, or monthly period. Maintenance scripts that are run at the beginning AM only if the computer is turned on 24/7 (no sleep). If this isn't the case, then a great solution is to download and install a shareware like Macaroni, JAW PseudoAnacronor Anacron utility that will automate the maintenance regardless of whether activity if the computer is off or asleep.  Dependence on third-party utilities to run periodic maintenance scripts has been significantly reduced since Tiger.  These utilities have little or no functionality with Snow Leopard or later version, and must not be installed.

  OS X automatically defrags files smaller than 20 MB in size, so unless you have a disk full of very large files it little need to defragment the hard drive.

  Under no circumstances should you install operating MacPaw or ZeoBit software (CleanMyMac/CleanMyDrive or Mac Keeper, respectively.) You don't need special software to keep your computer.

  Useful links about malware Protection

  "If you have an immediate problem with ads popping up see the Mac without danger" Adware removal Guide and AdwareMedic.

  Open Safari, select Preferences from the Safari menu. Click the Extensions icon in the toolbar. Disable all Extensions. If it stops your problem, then re-enable one by one until the problem returns. Now remove this extension as it is the origin of the problem.

  The following comes from user stevejobsfan0123. I made minor changes to adapt to this presentation.

  Difficulty a few pop ups browser that supported Safari

  Common pop - ups include a message saying that the Government has taken over your computer and you pay release (often called "Moneypak"), or a false message saying that your computer has been infected and you need to call a number of tech support (sometimes claiming to be Apple) to get it to be resolved. First of all, understand that these pop-ups are not caused by a virus and that your computer has not been assigned. This "hack" is limited to your web browser. Also understand that these messages are scams, so don't pay not money, call number, or provide personal information. This article will give an overview of the solution to remove the pop-up window.

  Quit Safari

  Usually, these pop-ups will not go by clicking 'OK' or 'Cancel '. In addition, several menus in the menu bar may become disabled and show in grey, including the option to leave Safari. You'll probably force quit Safari. To do this, press command + option + ESC, select Safari, press on force quit.

  Relaunch Safari

  If you restart Safari, the page will reopen. To avoid this, hold the "Shift" key when opening Safari. This will prevent windows since the last time that Safari was running since the reopening.

  It will not work in all cases. The SHIFT key must be maintained at the right time, and in some cases, even if done correctly, the window is displayed again. In these circumstances, after force quit Safari, turn off Wi - Fi or disconnect Ethernet, depending on how you connect to the Internet. Then restart Safari normally. He'll try to reload the malicious Web page, but without a connection, it will not be able to. Leave this page by entering a different URL, i.e. www.apple.com and try to load it. Now you can reconnect to the Internet and the page that you entered is displayed rather than the malicious.

  An excellent link to read is Tom Reed Mac Guide of malicious programs.

  Also, visit the FAQ XLab and read of detection and avoid malicious software and spyware.

  Check out these articles from Apple:

  Mac OS X Snow Leopard and malware detection

  OS X Lion-Protect your Mac against malicious software

  OS X Lion mountain - protect your Mac against malicious software

  OS X Mavericks-Protect your Mac against malicious software

  On the quarantine of file under OS X

  If you need antivirus protection Thomas Reed recommends to use ClamXAV. (Thanks to Thomas Reed to this recommendation.)

  The user Joe Bailey comes this equally useful advice:

  The facts are:

  1. There is no anti-malware software can detect 100% of malware out there.

  2. There is no anti-malware that can detect all targeting the Mac.

  3. the best way to prevent breaches the most is for you as the user is aware that

  the most successful malware attacks rely on sophisticated social engineering

  techniques preying on human greed, * and fear.

  4 Internet pop-up windows telling the FBI, NSA, Microsoft, your ISP has detected malware on

  your computer is designed to trick you into installing their malware thinking it's a

  protection against malware.

  5. some of the anti-malware market products are worse than malware

  go where they are supposed to protect you.

  6. be careful where you go on the internet.

  7. don't download anything from sites, you know are safe.

  8 avoid links that you receive in email, always be wary, even if you get something

  you think a friend is, but that you did not expect.

  9. If there is any question in your mind, then assume that it is malware.

  Troubleshooting Applications

  I recommend that you download a utility such as TinkerTool System, OnyX, Mavericks Cache Cleaneror hiding a Cocktail that you can use to delete the former newspapers and archives, cleaning, etc. Corrupted cache, logs or temporary files can slow down the application or OS X crashes and panics of the kernel.

  If you have leopard snow or leopard, then for similar repairs install Applejackfreeware utility.  If you do not start in OS X, you can boot into single-user mode , where you can run Applejack to make a set of routines for repair and maintenance of the command line.  Note that it takes 1.5 AppleJack for Leopard. AppleJack 1.6 is compatible with Snow Leopard. Applejack does not work with Lion and later versions.

  Basic backup

  For some people, Time Machine will be more than enough. Time Machine is part of Mac OS X. There are two components:

  1. a panel of Time Machine preferences as part of the system of preferences;

  2. a request for Time Machine, located in the Applications folder. It's

  used to manage backups and restore backups. Time Machine

  requires a backup drive that is at least twice the capacity of the

  drive being backed up.

  You can also get an external drive at least equal to the size hard disk internal and make (and maintain) a bootable clone/backup. You can make a bootable clone using the disk utility's restore option. You can also create and maintain clones with good backup software. My personal recommendations are (the order is not significant):

  1 Carbon Copy clone

  2. get backup

  3 already seen

  4 superDuper!

  5. Synk Pro

  6. Tri-Backup

  Visit The FAQ XLab and read the FAQ on the backup and restore.  Also read How to back up and restore your files. For using Time Machine, visit FAQ Time Machine of Pondini for help with all this time Machine.

  Referenced software can be found at MacUpdate .

  Additional tips

  Make sure you have a sufficient amount of RAM installed for the number of applications you run simultaneously. Make sure to leave a minimum of 10% of the capacity of the hard disk as free space.

  Add more RAM. If your computer less than 2 GB of RAM and you use OS X Leopard or later, then you can do it with more RAM. Snow Leopard and Lion works much better with 4 GB of RAM that is their system. Most concurrent applications, that you tend to use the more RAM you should have.

  Always have at least 15 GB, or 10% of the capacity of your hard disk as free space, the largest. OS X frequently accesses your hard disk, so offering enough free space will keep things slow down.

  Check for applications that may be hogging the CPU:

  Before Mavericks

  Open the activity monitor in the Utilities folder.  Select all processes in the drop process .  Click the % CPU column heading twice to display in descending order.  If find you a process that uses a large amount of time processor (> = 70,) then select the process, and then click the quit icon in the toolbar.  Click the force quit button to kill the process.  See if that helps.  Don't forget to mention the name of the runaway process, so you can find the cause of the problem.

  Mavericks and later versions

  Open the activity monitor in the Utilities folder.  Select all processes in the menu display .  Click the CPU tab in the toolbar. Click the % CPU column heading twice to display in descending order.  If find you a process that uses a large amount of time processor (> = 70,) then select the process, and then click the quit icon in the toolbar.  Click the force quit button to kill the process.  See if that helps.  Don't forget to mention the name of the runaway process, so you can find the cause of the problem.

  This problem occurs often because of a corrupted cache or the preferences file or an attempt to write in a corrupted log file.

• Measuring current using USB-6009 with a rheostat shunt resistance

  Hi all, I am an electronic engineering student doing my final year project. I am able to measure the current and voltage of a 9V battery, but not knowing the method that I use if it is correct.

  For the voltage, I have no problem getting it. But for the current, I connected a resistance of 1 k in parallel with the battery. When I run the program, I have a 9mA for battery. I understand when you use the DAQ assistant, for the installation of measuring current for USB-6009, that I need to specify as "external" shunt resistance and shunt resistance value (which is 1 k for the above experience).

  So, my question is when I use a rheostat as shunt resistance, what value should we indicate as a rheostat is a variable resistor, so it doesn't have a fixed value.

  Or the dimmer cannot be shunt resistance?

  Really need help and thank you for the reply.

  
  

• Can I use two USB 6211 to replace a USB-6009

  Hello

  I got a labview vi., 5 output channels digital, 2-channel digital input, 2 analog inputs are necessary for the execution of this vi.  Initially a 6009 usb is used to run the vi. But I have only two usb ports 6211 now, which has digital to digital for each data acquisition 4 inputs and 4 outputs. I wonder, can I use two usb 6211 to run the vi. ? What should I do?

  Reverse lines are wrong, does that mean it will display 0 for false and 5 V 1.

  Active drive is the normal mode of the digital output: it generates tension when said.

  I forgot one thing: that you are behind the wheel of these lines, how much power do you need?

  Analog output is less powerful, it can give only 2-4 mA, while the digital output 6009 could give 8 my.

• Video of the MacBook Air to accuse by unplugged (current running off battery)

  Hello. I have a Macbook Air from 2012. The Macbook works perfectly fine when it is plugged, but the minute I unplug the unit, some video that I might be streaming suddenly freezes, even if sometimes the audio is not yet. Weird. The battery works, even if it runs in less than an hour. It has a cycle of 657 counter. The battery health is diagnosed as being 'good '. Anyone know why this is happening and what I can do about it?

  Thank you.

  Apparently, the MacBook Air is electric rationing of the battery through the

  all of the GPU, CPU, free wireless internet, open, applications and requirements

  Mac OS x itself; so many invisible things are underway in the background.

  Have you looked into the specifications of profile of electrical system and battery

  where the status of the battery is spelled in milli-ampere-hour charge remaining

  and expected full load capacity?

  I imagine that the battery can be replaced; also if SSD drive

  is full of stored content, the effort it takes the system to find the space

  for swap files and read/write then in the storage disk, is your MB/Air tax.

  Maybe an upgrade of the hard drive (SSD) ability is something to check

  in (if it is possible to upgrade) or just be sure to not have much stored on board.

  A replacement may be obtained from the macsales, OWC, among others.

  Also make sure that the MagSafe connectors are clean and free of debris on both sides

  the AC adapter and the DC-in Board (on the computer).

  For more information on batteries for portable laptops, & magsafe Chargers:

  • About batteries for laptops Mac - Apple Support

  • Laptops Apple: Troubleshooting MagSafe adapters - Apple Support

  If yours is a model 11 inches, total expected her battery life cycles are less

  as the largest 13-inch model (with the largest capacity of the battery + request) if the

  County of 657 (of max. 1 000) can be decreased if the computer has never been

  Let it run until the battery is dead. ~ Or if the storage environmental conditions or

  use, have marginalized the ability of the computer to function in the plug.

  • Reset the management system (SCM) controller on your Mac - Apple Support

  • How to reset the NVRAM on your Mac - Apple Support

  The SMC reset (and sometimes reset NVRAM) can help with the battery power

  management in general; but the battery may be suspect. The battery charge

  includes everything in the MacBook Air; brightness, audio volume, so the screen

  the use of Wi - Fi, other applications that run in the background; also the antivirus or other

  analysis software running needlessly in the background, using cycles CPU. The

  battery may be getting a workout. More so, if you run games or any other active content.

  You could look at the activity monitor to check the different points under your control

  who may be using resources; all this that consume energy are suspect. Some of them are

  more in your control than others. the system manages several outside of your access.

  An Etrecheck report generated when the unit is running under the battery and another

  When operating on current alternative, can be useful. If nothing else, to see what is

  installed in the computer and its running configuration specifications. The load can tell a story.

  http://etrecheck.com/#about

  There is also perhaps adware or other software that affect the performance of the Mac;

  This may include antivirus, and if cleaning applications have been executed, they can damage the OS X.

  A free to use app, formerly known as "adware medic" now malwarebytes, can help:

  •Malwarebytes | Malwarebytes Anti-Malware for Mac

  https://www.Malwarebytes.com/antimalware/Mac/

  Malwarebytes Anti-Malware (was AdwareMedic) return of experience helps you get your Mac.

  Hard to say exactly what is happening. -If it were mine, I would look in different details.

• Satellite Pro A60 PL: message: USB device can run faster

  Hello!

  I have a problem with the USB 2.0 drivers in my Satellite Pro A60 PL. everytime when I connect the message apear theres USB 2.0 device this device can run faster. What can I do about it?

  Hi guys

  I received the same message. It s not an error but a balloon tip Windows.
  I didn't find the reason for this message because my phone supports USB 2.0 ports too and I also connected a USB 2.0 compatible device.

  I've tired to remove the Device Manager, the controllers and the USB hubs and updated the Win XP operating system to the last State. I've also updated the driver chipset but sometimes (not always) this message again using a disc HARD 2.5 USB.

  I read in some professional computer magazines that this message is normal and it might appears with some SATA external USB hard drives. So you can ignore it.
  It s nothing serious.

  Greetings

• Current output digital USB-6009

  Hi, I'm trying to increase the voltage output digital device USB-6009. I read a few topics on the use of a relay, but I couldn't get it.

  I was thinking of using power 5V on the map because there current 200mA on it, but when I use it with open-collector output, it cannot change the relay. When I measure the current between

  5V and ground: 200 ma,

  5V output, I read a value around 30-40 my.

  Why can I not use this 200mA with output? It is the Relay that I use.

  If this is not possible, can I use an external power supply 5V (with more current) and a digital output to pass the baton without damage the 6009?

  Outputs digital of the USB-6009 confined to 8.5 my. Your relay coli requires much more than that. Even if the power source can provide enough current for the relay, digital output can not put.

  The solution is to use a buffer of extermal. The ULN2003 can switch currents up to 500 my and voltage up to 50 V while being controlled by digital output.

  Lynn