What is a dvi input

Similar Questions

• HP Pavilion a6750f: problem dual monitor (Second monitor not detected in DVI input)

  Hello everyone, I'm going to by a problem of not being able to setp toward the top of my second monitor.

  I own a HP Pavilion a6750f with an ATI Radeon HD 3200 card on board running on Windows 7 Ultimate 64 bit operating system.  In the back, I have two VGA and DVI inputs, VGA works, but when I connect the other monitor which is connected to a DVI adapter on the back, Windows does not detect any.

  I tried to go the DVI adapter to the other monitor and noticed that it refuses to work. I will note that my display drivers are all updated and I activated the option of customization to detect the second monitor, nothing shows up, it will not be the same acknolowdge that there are several screens.

  I think it's weird that I don't see this problem being issued when I was searching for a resolution on google for hours now. If someone can help me here please I would be very happy.

  Just to remind you try to connect a VGA (analog) monitor to a DVI - D (digital only) output on the computer. This is never going to work as analog and digital are two completely different incompatible signalling methods. With the help of an adapter DVI / VGA passive is the problem that these cards may work with DVI - I or DVI - A output... not DVI - D.

  Wikipedia - DVI;

  "More digital, the DVI connector includes pins that carry an analog signal compatible with RGBHV signals in a VGA connector. This allows a VGA monitor be connected to a passive adapter and offers a universal solution for the DVI interface. The analog pins are the four that surround the apartment or cross the blade as shown on the right side of the diagrams below. »

  

  8 analog vertical sync

  C1 - analog Red
  C2 - analog Green
  C3 - blue analog
  C4 - analog horizontal sync
  C5 - analog ground

  Note the absence of the pins on your computer and your so-called card C1, C2, C3 and C4. Without these pins is not just going to work. Still, there is no way to get an analog VGA monitor to work with your digital DVI - D only output using a so-called DVI - D to VGA. You may be able to buy an asset DVI - D to VGA Converter, but this will be expensive and cannot provide a poor video image quality.

  As you said, the HP f1703 monitor supports only VGA. However, based on the specifications, your HP w2207h 22 inch LCD monitor supports the entry to a VGA and a HDMI input. HDMI and DVI - D share the same signage and using a HDMI-DVI cable or adapter HDMI-DVI and HDMI Cable will solve your problem. For two monitors running on your computer, please connect as follows:

  Computer > HDMI-DVI cable or adapter HDMI-DVI and HDMI Cable > HP w2207h monitor

  Computer > VGA cable > HP f1703 monitor

  Please send Bravo

• DVI input supplement on my monitor

  I own a HP Pavilion PC connected to a monitor of HP2010i p6631 and I would like to have the monitor connected to the 2 hard drives, but only see a DVI input connector and I think that I need another.   Is this possible and if so, how.  Thank you

  Hello

  You probably need a switch because you can only have 1 computer at a time. Please, try the next option:

  http://www.WikiHow.com/operate-multiple-computers-with-one-keyboard-and-monitor

  Kind regards.

• C60 DVI input 3 Auto Detect using a DVI to VGA splitter

  Hello

  We install a codec C60 using a splitter DVI input n ° 3 for the presentation source (DVI - I male to DVI - D & VGA Splitter cable's female adapter)

  The DVI input source is configured as Auto-Detect.  Administrator's Guide confirms this seting automatically detects the signal is analog (VGA) or digital (DVI or HDMI).

  The problem is the codec can't really switch from one source to another.   We do not seek to send two signals at once, but rather stable wether VGA and HMDI will be detected by the codec according to the entry sends the laptop.

  can anyone confirm if this is a limitation of the codec, or bug in firmware or even simply impossible without adding additional hardware.

  see you soon,

  Mel

  Hello

  Yes, auto-detection works for me.

• What is the keyboard input HP microsoft 10 key

  What is input keyboard microsoft 10

  advise please

  What is the entry on hp microsoft 10 key

  none showed urgent

• In Labview 8.5, what happens if the input signal exceeds the scope of the signal defined by the DAQ Assistant?

  Hi all

  This should be a pretty simple question, but I can't seem to find the answer online and currently do not have the functionality to test this:

  I'm using LabVIEW 8.5 and have a VI that imports data from sensor through the DAQ Assistant. In the configuration tab, there is a range of signal input. What happens if my sensor exceeds this range? I get a warning? The default value is the maximum (or minimum)? I was interested in writing a code to display an error that I approach the limits of this range, but did not know if I also need to include code to display an error if the scope is exceeded as well.

  Thanks for the help,

  Tristan

  Hello, Tristan,.

  The behavior depends on the selected range and the device you are using.

  If you are using a device with a single input range is valid, we will use this range, even if you set a smaller minimum and maximum in the DAQ Assistant.  So, if your device only supports ±10V and you set the range to ±8V, you will still continue to get valid data after your top sensor 8V until what you approach 10V.  When you reach the limit of the extent of your device, the output will be 'rail', and simply return the maximum value until the signal is less than the maximum value again.

  Note: A device that is nominally ±10V usually has a go-around (such as ±10.2V) which are usually specced in the manual.

  However, if you use a device with several ranges of entry then things become more complex.

  NOR-DAQmx player will choose the smallest range that entirely covers the interval you choose.  For example, suppose that your device supports the following input range: ±0.2V, ±1, ±5V, ±10V and you choose 0V - 3V as the range in the DAQ assistant.  The NOR-DAQmx driver will focus on the input range and the list of the entry lines that your hardware supports and choose the smallest encompassing the entire range that you set.  This would be the ±5V, because this is the only beach that contains up to 3V.  Thus, all between ±5V input signal is returned and none outside this range will be 'rail' to the maximum or minimum value.

  We do this because using small beaches make more efficient use of the resolution of the ADC.  So, we try to use the most effective range based on what you ask without picking up a range that will make you miss data.

  Let me know if I can clarify it more.

• What is the analog input of the NI PCI-6229 impedance?

  I am trying to determine the effect of a 12 K resistor that is in series with an analog input of an NI PCI-6229 data acquisition card.  Resistance of 12K seems to be part of a RC filter.  I have a 0-10 VDC source this supply circuit.  What is the impedance of the analog input of the NI PCI-6229 data acquisition card?  If it makes any difference, the analog input is connected in differential mode with a 180K resistor to Gnd AI.

  Thank you

  RWB

  Hi, RWB,.

  The input impedance is classified in the specifications 10 GOhm.  So, the effect of your k 12 resistance should be relatively low.  Take care!

• Dell E2416H Displayport/DVI input

  Hi everyone, I bought a Dell E2416H. My pc has a dvi output port & vga. E2416H has vga and display port of entry. Now I use the vga port, but I want to use displayport for better quality. I bought a cable that is displayport (male) to dvi (male) but it did not work, Caron was passive. I have read some information on the web, people say that "active adapters (dp/DVI) should be used.

  How do I do it please help...

  The E2416H can only 1920 x 1080, in your case, using DP will look no better than to use the VGA, so use one of its ports.

  A DVI output port video card cannot convert up to monitor DP/CDM in ports through a straight through cable. What you have purchased is designed to down convert a DP/CDM map video signal to a DVI monitor port. You must purchase a current converter.

  Video card DVI out--> DVI converter DP --> DP to DP cable--> monitor DP in

• Mac Pro 1.1 GeForce 7300 GT - what type of DVI?

  Hi all

  I would ask for more information.

  I'm about to buy a Mac Pro with 2.66 processor and graphics card, Geforce 7300 1.1.

  Currently, I have a LG L19WT monitor that has both the VGA output of DVI output and I want to understand if there are particular problems in the use of this monitor with the Mac Pro, because I read that there are different types of DVI, and I don't know if it is compatible, or even because I have to buy the cable.

  Thank you all.

  Vincenzo

  No problem at all. Simply connect the Mac and the monitor via a cable DVI.

  However, I wouldn't buy a Mac Pro 1.1. (2006) 1.2 or 1.3 even (2008).

  They are not very good. 2006 and 2007 are limited to OSX 107 unless you make a cut.

  The 008 is not that bad, but the memory runs hot like the previous ones, and often fails.

  Better is a 20o9 or later of Mac Pro. 2009-2012 are essentially the same.

• Qosmio G30-161: Cable for HDMI output on DVI input

  I have my G30-161 "HDMI" output as well as the analog out. I began to find a cable to connect it to the DVI to a TFT monitor, but seem to have trouble identifying which is the end "HDMI" cable connection. Does anyone know the formal classification of HDMI connector (or a UK power cable) I can be sure I buy the right cable?

  Thank you very much

  Phil

  Hello Phil

  Put? HDMI-DVI adapter? as keywords on Google and you'll find enough online shops where you can order one.

• With U2410 PIP: cannot use the HDMI and DVI inputs at the same time

  Hello

  I can't have a HDMI source and a DVI source on the main screen in the picture-in-picture (or visa versa). Trying to choose the entry in the menu PIP PIP shows grayed out the HDMI and two DVI sources. The manual does not address this. Is this a limitation of design or a known issue that is under development?

  "Technological evolution is like an axe in the hands of a pathological criminal." (Albert Einstein, 1941),

  Dr. Z.

  Dr. Z..
  It's normal.

  Source = VGA main
  PIP = DVI, HDMI, DP, component, Composite

  Source = DVI
  PIP = DP, Component, VGA, Composite

  Main Source = HDMI
  PIP = DP, Component, VGA, Composite

  Main Source = DP
  PIP = VGA, DVI, HDMI, component, Composite

  Main Source component =
  PIP = VGA, DVI, HDMI, DP, Composite

  Main Source = Composite
  PIP = VGA, DVI, HDMI, DP, component

• Codec of Tandberg C series - DVI - I adapter

  Hi guys,.

  I'm trying to understand the DVI ports on a codec C60. I need to connect a VGA (from PC) input and an Hdmi output (on a plasma screen). I can only find vga-vga cables and hdmi to hdmi cable (good quality).

  I want to know what type of DVI/VGA and DVI to HDMI adapter that I need to buy. DVI - I ports on the codec.

  For the vga cable should I buy an adapter DVI - A, even a vga DVI - I adapt, just not a DVI - D adapter?

  For the hdmi cable should I buy a hdmi to DVI - D, even a DVI adapter - I adapt, just not a DVI - A adapter?

  Is the corect above or not?

  Thank you

  Silviu.

  Hello

  To pc with VGA output, you use a VGA/DVI-I or DVI - A VGA cable.

  For the connection to the screen if your screen has a hdmi input, you use an hdmi cable to hdmi.

  If your screen input dvi, then it depends on what type of dvi input there. If DVI - I or DVI - D, you can use HDMI/DVI-I or HDMI to DVI - D cable. If the DVI - A, then you probably need a digital analog converter between the two.

  Sent by Cisco Support technique iPhone App

• No input vga no signal dvi or

  I just bought a custom built Gamining PC. Every now and then when I start the pc I get the message "' NO signal vga input / no monitor DVI input signal go to sleep" I turn off the pc and wait a few minutes and then try to start the pc again. " After about 3 to 4 times to go through who / pc boots fine and desktop is displayed on the monitor.  So, what could be my problem?  It sounds as if there is a problem with my video card?

  TlWilliams,
  Thank you for visiting the Microsoft Answers community forum.

  Yes, that sounds like a video card problem.  Or it could just be a cable or in bulk.  Check the cable that goes from the video card to the monitor to make sure you it is connected at both ends, try change if it is editable, turn off your computer and reinstall your video card (take out and put back) If you are comfortable doing this, or contact who built to allow you to take a look.

  Let us know if we can help you.
  Thank you
  Gloria
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Input DVI does not?

  Hello. I have my desktop connected via the VGA port. I am trying to connect my XBox 360 to the entrance with a DVI - Vga adapter DVI and vga switch xbox plug. When I turn on the XBox and try to switch to the DVI input, he says there is no input signal. No reason?

  A DVI port on a monitor must have DVI or HDMI as a source, a VGA source on an xBox will not lead the DVI input on monitor.

  VGA-> adapter-> DVI = No.

  DVI-> adapter-> VGA = OK

  There is only one monitor that HP has recently who would do what you want to do, and it's the w2558hc. This is the DVI input is DVI - I, all others are DVD - D.

  See you soon,.

• Satellite A200 - Radeon HD 2600: cannot reach 1680 x 1050 using a HDMI-dvi cable

  Hello

  I use a LCD (ACER 22 ') which has VGA and DVI inputs. When I connect my laptop to the screen using the VGA cable, I get resolution 1680 x 1050 without problem, but when I want to use the digital output of the laptop (using an HDMI to DVI cable), I can reach only 1440 x 900.

  In the center of catalyst, the max of my screen 22 '' resolution is 1680 x 1050, but this resolution is not displayed as an option when I select.

  What is the problem? I've updated the graphics driver with the latest version of the end of January, but no change...

  Hello

  I did not have the opportunity to test this but check please interesting discussion here.

  Good bye