What is continuous and Dangling channel mode in VPN mode?

Similar Questions

• Setting port channel between UCS - FI and MDS 9124 (Mode F)

  Dear team,

  We tried to create the channel of port between UCS FI and MDS 9124

  But the port channel do not take action in mode F on MDS 9124

  FI is in host FC end Mode

  We have allowed FC uplink on FI trunking

  We have activated NPIV on MDS

  We have activated the MDS trunk

  FI and MDS in default VSAN

  To check that we have changed the way FI FC channels mode and switch port became active, but in E mode

  When we enabled CF trunking of uplink on the port mode FI channels and FC Switching became active in mode TE

  but in both cases above, showflogi database shows WWPN of SAN alone does not have the any fi.

  How to achieve this?

  Have read that no need to change the mode switching mode of CF swicthing and keep FC Endhost way

  SO how to channel ports with mode F MDS and FI (Display Mode as NProxy)

  What is it has nothing to do with the MDS NX - OS version? (https://supportforums.cisco.com/thread/2179129)

  If yes how to put as license for ports came with the camera and we don't have any CAP/PAK or license file as she came

  with license

  Also, we saw 2 files available for download (m9100-s2ek9-kickstart - mz.5.2.8 .bin and m9100-s2ek9 - mz.5.2.8 .bin b b) to use

  Thanks and greetings

  Jose

  Hi Jo Bo.

  What version of the software if your MDS race?

  On your UCS do connect nxos and show ficelleStringString ficelleT inteface and find the mac address.

  It is possible that you could be hitting the bug below. If this is the case, you may need to update the firmware on your MDS.

  Add MAC YES '002a6a', '8c604f', '00defb' for 5 k/UCS-FI

  http://Tools.Cisco.com/support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId= CSCty04686

  Symptom:

  Link change cannot connect any other Nexus or other Cisco Switch in mode VAN with a port channel F.   Question can be viewed in older versions of 5.1

  5.1.3.N1.1a

  but not later

  5.1.3.N2.1c

  Release. Question is also found in

  5.2 (1) N1 (1)

  and

  6.0 (2) N1 (1)

  and later versions.

  Conditions:

  Nexus configured for the link SAN PortChannels or NPIV Nexus mode connected to the UCS via regular F port channel where UCS VAN VAN edge mode switch: YES switch manufactured FI or another Cisco UCS Port WWN: xx:xx:00:2 has: 6a: xx:xx:xx or xx:xx:8 c: 60:4f:xx:xx:xx

  Workaround solution:

  Turn-off on Nexus 5 k TF-port question link mode does not happen with standard F-PORT SAN to remove Portchannel config

  Other Description of the problem:

  To check question collect please see the flogi-event history internal errors whenever the port is attempted OLS, AMENDMENTS, PBA counters will increment. This can be determined via the following output, view port internal info to see all the internal-historic port of error events

• Error: "CHKDSK cannot continue in read-only mode" and "an unspecified error has occurred (766f6c756d652e63 3f1).

  I'm trying to run a CHKDSK on my hard drives. Whenever I try to do "chkdsk C:" or any other volumes (internal or external) invites of high command. I had

  "This type of file system is NTFS.

  Errors found. CHKDSK cannot continue in read-only mode. »
  (That's all I get, nothing in between)

  I have three internal volumes C: D; and E:. Running chkdsk on a volume any returns "CHKDSK cannot continue in read-only mode. Run with / f on C: will check the disk (no error) is restarted. Run/f on any other volume, I had "an unspecified error has occurred (766f6c756d652e63 3f1).
  Has received the same error in recovery mode, safe mode, using the account administrator or UAC disabled.
  Also got same error when you try to chkdsk on all external hard drives.
  I have formatted my E: and ran chkdsk on an empty volume, got the same error.

  Defrag works OK without any problems. External hard disks can be verified (no error and the bad sector) to another computer (win7 pro x 64).
  My external hard drives can be ejected without any problem. But ejection always fail after running "chkdsk /f.

  This computer is win7 pro x 86.
  Installed software: VMWare workstation 7, Microsoft Security Essentials, Visual c# 2010 express, Office 2003, Daemon Tools. DropBox

  Please help me to solve the puzzle.

  Thank you
  Hello

  After some debugging, I found that the ifsutil.dll reported an exception 'divided by zero.
  Finally I found that there is a fix from Microsoft for my netbook CPU (AMD C60).
  A Chkdsk command fails with an error not specified on a Windows Server 2008 R2 or Windows 7-based computer that uses a low frequency CPU AMD
  http://support.Microsoft.com/kb/2502789
  This fix solved my problem.

• My wallpaper appears only in the extended format. I want to display a .jpeg file into the center channel mode. I click on center and save the changes, but he remains in stretch mode...

  My wallpaper appears only in the extended format.  I want to display a .jpeg file into the center channel mode.  I click on center and save the changes, but he remains in stretch mode...

  HP technical support solves the problem for me with a patch: I'm sorry that I don't remember all the steps they walked me through but the patch was SP45575. EXE.   It was working fine.  Good luck

• When I open a PDF and try and connect you to convert the document to word format he said "reader has no ability to access this service" and it doesn't let me move forward. What this means and how do I continue to Word so I can edit pdf

  When I open a PDF and try and connect you to convert the document to word format he said "reader has no ability to access this service" and it doesn't let me move forward. -What this means and how do I continue to Word so I can change the pdf document?

  Hi wayned76005641,

  You subscription Adobe export to PDF, make sure that you are signed in DC from Adobe Acrobat Reader Adobe - Adobe Acrobat Reader DC Distribution using your Adobe ID to use the service to export it to PDF service The Adobe export in PDF format allows you to convert a PDF to Word, Excel, PowerPoint and RTF formats..

  You can also use this online https://cloud.acrobat.com/exportpdf service

  Once the PDF is converted .docx file you can edit in MS Word.

  Kind regards
  Nicos

• bought photoshop elements several weeks ago and started the download process, but I had to stop... needed to upgrade my mac so I could continue... now it won't let me continue and download the program. What should I do to correct this?

  bought photoshop elements several weeks ago and started the download process, but I had to stop... needed to upgrade my mac so I could continue... now it won't let me continue and download the program. What should I do to correct this?

  What do you mean won't you of... What is the error message?

  kglad links in response to #1 here can help https://forums.adobe.com/thread/1930162

• Dual channel mode is not enabled on the Satellite P50T-B-10V

  Hello

  I recently bought a laptop by Satellite P50T-B-10V.

  Everything works fine, but I saw in the software helped that it s not activated for 1The memory channel mode, although the chipset support this mode.

  How can I solucionate what mind?

  + Memoria driver +.
  + Type Dual Channel (128-bit).
  + Modo Activo single channel (64-bit) +.

  I hope that your answers! Thank you!

  Dual channel mode can be activated manually.
  Mode dual channel will be activated and used automatically if all of the requirements be fulfilled.

  What does that mean?
  Well, to use the two channels, you need two memory modules and both modules need to support dual channel.

  The Satellite P50T-B-10V seems to be equipped with a module of 8 GB RAM
  http://www.Toshiba.PT/laptops/satellite/satellite-P50-b/satellite-P50-b-10V/

  This is why the double channel does not appear to be used.

• 4530 > upgrade to UMTS? Upgrade SSD? Upgrade RAM? Upgrade processor? What is possible and what is not

  Hello

  I have a HP Probook s 4530 with an Intel Core i5 2410M, 4 GB of RAM to processor and a normal SATA.

  Now, I want to upgrade the following parts

  an SSD (max. 256 GB)

  increase the RAM up to 8GB

  If possible:

  Update of the UMTS Modem

  and when it's not expensive and not so expensive:

  upgrade to a Blu ray player player

  and an upgrade to 2630QM processor

  Now my questions:

  What disk SSD can you recommend? That the bios settings are the best for this?

  I found: Intel SSD 335 series 240GB, 2.5 ", SATA 6 Gbps (SSDSC2CT240A4K5)

  Is the standard RAM (4 GB) inside the laptop capable of dual channel mode and can easily buy an another RAM from another company?

  What is the best?

  is it possible to upgrade my normal 4530 s with a UMTS module?

  How is the name of the product?

  now for the processor:

  which is the best for my laptop? and compatible with my motherboard and the other material?

  Please fill out the processor type

  Thank you

  You will need this:

  Repair manuals

  It's the fastest clock speed processor that you can install:

  I7 - 2620 M 2.70 GHz (Turbo up to 3.40) processor 4 MB L3

• Error: "CHKDSK cannot continue in read-only mode" when you try to run it on the E: drive.

  Original title: CHKDSK does not work on my Windows 7 laptop

  I'm trying to run a CHKDSK on my external Hard Drive E: but everytime I try to CHKDSK E: in the shell, all I get is

  "This type of file system is NTFS.
  Errors found. CHKDSK cannot continue in read-only mode. »
  (That's all I get, nothing in between)
  I tried to make the Tools section of error checking, but it does not work there either...
  If this is a problem with the operating system, I don't have a Windows 7 disc because my laptop came with it pre-installed
  So, what should I do?

  Hello Rayzorexe,

  Thanks for the response back.  You are able to start your computer and get the recovery options?  From there, you can run "Command Prompt" and I want to know if you are able to run Chkdsk from there successfully.

  Are you the same response from the commands below:

  Type 'chkdsk e:' in the command prompt. Press 'Enter' to run the utility to check the disk in read-only mode. He locates errors but does not fix the

  Enter 'chkdsk e:/f' in the command prompt. Press 'Enter' to run the disk check and correct errors without analyzing bad sectors.
  

  Type 'chkdsk e:/r' in the command prompt, press 'Enter' to do a thorough analysis of the sectors and files and repair any problems found.
  

  Recovery options:

  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

• Tungsten T3 Hot Sync in Windows 7 Ultimate 64-bit and WIndows XP mode

  I've upgraded to Windows 7 Ultimate 64 bit and now my Palm T3 will not be synchronized.  I downloaded desktop 4.1.4e 6.3 and 4.1.4. I tried all three in both windows 7 and windows XP mode that tells me is a 32-bit o/s but I'm really not sure.  I tried to hot sync in bluetooth in windows 7, as the T3 and laptop connect but he always tells me that the port is used by another program? Does anyone know what I have to do to get it to sync or am I've sentenced to throw my faithful T3 out? Any ideas?

  Hello eaglesfan723 and welcome to the forums of Palm.

  The Tungsten T3 HotSync driver is not 64-bit capable, this is why you can't get the T3 to HotSync.  Please read this thread to learn more about your options with Windows 7.

  Alan G

• TS of HP ENVY 17-j043cl and dual channel memory

  I am very happy with my new computer laptop 17-j043cl of envy, but I see it came with 12 GB of RAM, 8 GB DIMMS and a 4 GB DIMMS.

  If I replaced the 4 GB DIMMS with a 8 GB DIMM caller, the memory would be in dual-channel mode, offering a performance gain, or this computer only supports single channel memory?
  
  More concretely, the performance gain would be sufficient to justify the effort?
  
  (Although, really, I'd probably do it if there was even the slightest advantage of performance or efficiency.) "I'm just that kind of GUY!)

  Thank you!

  Hello

  Please find the link given below for your unit specifications shows clearly your device supports up to 16 GB. And for your question about the upgrade, it will improve the performance and speed of the device.

  Link
  

• 3 years, 6 accidents - why is what is happening and how to stop it?

  I got my iMac 27 2013 with 32 GB, 3 TB and a fusion drive. Six months after the merger by car became separated from the logical drive (if that's the correct term). Some time after that repair, it crashed kernel hard so that even with an Apple phone support they were gather to reinstall the software. Six months later the familiar Rainbow ball came, he began to slow down and crashed again. I reinstalled from TM and about half a year later it crashed again - and so on. When the Rainbow ball appeared before the last crash I ran every diagnostic I could find on the line and then on them again with Apple rep on the phone. They have picked up for the third time and kept for a week sending him by saying they could find nothing wrong. Now he broke down again.  Why?

  I knew that to put a version of Yosemite on an external HARD drive, so I can run the computer from that. I can connect the 2013 with my Macbook and Thunderbolt cable, too. I called Apple and asked them to have the look of engineering team on newspapers OS for me. They go back to me next week. So, I have this bum computer on my desk and I'm trying to make sense of what's wrong with it.

  It does not start in safe mode. Of course, I ran repair disk through the Macbook (thunderwire), Terminal (while connected through Yosemite on this external HARD drive, I mentioned) and the Recovery Mode. Which made me think maybe I could divide the disc and put a new OS on half. Nope. I tried with the two diskutl, fdisk (by pure frustration) and TPG if Airmac, Yosemite and the Recovery Mode. In all cases, the drive could not be mounted or busy. I tried to disassemble the drive of the terminal to start a partition and also to split the partition but nothing works.

  Based on the information that I gave you, does anyone have an idea what is happening with my OS? It's like there a part of the program that deteriorates over time. It is really frustrating, is that I still have my iMac 2009 with the same exact programs and I work through the same data (sharing data through my network). If it was something about my data, it should affect my other computers, right?

  Any ideas or thoughts you have are appreciated.

  Can explain how it "crashed" in more detail?

• Checking file system on C: the Type of file is NTFS. The Volume is dirty. -What this means and how do I clean the Volume, please? My computer is Dell XPS

  Recently, when I turn on my computer is starts, guests of the computer and starts check my system files as follows: "checking file system on C: the Type of the file is NTFS. The Volume is dirty. "That is what this means and how can I clean and maintain the clean Volume, please? My computer is Dell XPS

  The computer system continues and invite "CHKDSK checks the files (step 1 of 3)... .

  The system deletes some files and at the end of shows, complete audit files and then show

  CHLDSK is verifying indexes (stage 2 of 3)...

  Once again, it shows the following:

  Deleting Index Entry _64280 ~ 1. jpg in index file 4632 $130

  Deleting Index Entry _64280552_little-mix_211112_get [1] .jpg in index file 4632 $130

  Deleting Index Entry 69gw [1] .jpg in index file 6722 $130

  Remove entries of Index 69 GW_1 ~ 1. jpg in index file 6722 $130

  Deleting Index Entry _64274754_messi_211112_elvis [1] .jpg in index file 6722 $130

  Deleting entry Index _64274 ~ 1. jpg in index file 6722 $130

  Finished the index checking

  CHKDSK is checking security descriptors (stage 3 of 3)...

  100%

  CHKDSK checks usn Journal...

  Windows control disc is finished.

  After all checks, Windows proceed to start as usual.

  I would like to know if I need the dirty Volume, and if so, how can I carry out the cleaning operation.

  Sometimes, at the early stage of the CHKDSK, the computer makes a pe. .. PE... noise and cut.  Then I turn the computer off via the key of the insulation. When I restart the computer, it then runs the check again until the end.

  Please advice me on the following points:

  1 is this normal as he started only happening in recent weeks?

  2. How can clean the Volume in order to show "Volume is clean instead of sale"

  I look forward to hear from you.

  Thank you

  Hi, Dr.,

  Volumes that contain file system errors are known as Sales. To indicate that a file system problem has occurred and that the volume is dirty, Windows XP Professional displays a message similar to the following when you try to open, delete, or rename a file or folder by using Microsoft Windows Explorer or the command prompt:

  Autochk runs if the volume is marked as modified.

  If the file system has marked the volume as dirty, Autochk runs the Startup Repair process. Volumes are marked as dirty, when the file system detects an error on the volume. If Autochk detects a dirty volume, it provides a delay of 10 seconds, and then starts the repair process. If you cancel Autochk when a volume is dirty, Autochk tries to run again after a 10 second delay every time the computer is restarted.

  See Chkdsk for all the necessary explanations:

  http://TechNet.Microsoft.com/en-us/library/bb457122.aspx

  Run the Dell Diagnostics to check the drive failure.  If the disc is a failure, it must be replaced.

• Aspire Revo R3700 memory does not work in dual-channel mode

  Hello

  I have a Revo R3700 a few years now with 2 GB of memory. The PC came with the DDR3 10600 Hynix 1x2GB memory module.

  I recently bought a second module of the same 2 GB of the same brand (Hynix) and part number.

  After you install the BIOS and Windows detects 4 GB with no problems and everything seems to work fine, but CPU - Z tells me the following:

  (1) it is running in single channel and not dual-channel mode.

  (2) aren't 399 MHz and 800 MHz.

  3) SPD 1/2 bandwidth is 667 MHz and no 1333 MHz.

  Do I need a BIOS update or configure something?

  Sorry if I mix things up.

  Thanks in advance

  I've attached screenshots below.

  

  

  

  Module original stock Acer is on the left. A new one on the right.

  

  The Aspire AR3700 doesn't support dual channel. This system only supports single channel.

• I reinstalled Windows XP & he said that if I continue, I'm not able to connect to Windows. I hit continue, and now I can not connect.

  I reinstall windows xp & he said that if I continue, I'm not able to connect to windows. I accidentally hit continue and now I can't log on. Help, please. What should I do now? Lynn B.

  original title: Reinstalling windows xp

  Hi Lynn B,.

  ·         What is the exact error message?

  ·         What type of installation you perform? Is this an upgrade or fresh on-site installation?

  ·         What service pack is installed on your computer?

  ·         You have the Windows installation disc?

  You can consult the following Microsoft articles:

  Install, reinstall, or uninstall Windows

  http://Windows.Microsoft.com/en-us/Windows/help/install-reinstall-uninstall

   

  How to perform an upgrade on the spot (reinstallation) of Windows XP

  http://support.Microsoft.com/kb/978788

  Hope this information helps.