Error: "CHKDSK cannot continue in read-only mode" when you try to run it on the E: drive.

Similar Questions

• Error: "CHKDSK cannot continue in read-only mode" while trying to perform the disk check

  : Title real: my backup is suddenly not recognized in Windows 7

  A backup I use regularly is currently not recognized - I went through several pages of suggestions without deleting the instructions to format the drive. I did chkd sk/p/r suggestions with this result:

  Microsoft Windows [Version 6.1.7601]

  Copyright (c) 2009 Microsoft Corporation. All rights reserved.

  
  

  F: C:\Windows\System32>CHKDSK

  The type of the file system is NTFS.

  Volume label is Micron disc for backup.

  
  

  CAVEAT! F parameter not specified.

  Running CHKDSK in read-only mode.

  
  

  CHKDSK checks the files (step 1 of 3)...

  11520 file records processed.

  Finished files checking.

  11 big folder files.

  0 incorrect file records processed.

  0 EA records processed.

  0 analysis of the cases handled.

  CHKDSK is checking the index (step 2 of 3)...

  53 percent. (12004 index entries processed 11514)

  Error detected in the $I30 for 5 file index.

  Error detected in the $I30 for 5 file index.

  12004 index entries processed.

  Index verification completed.

  
  

  Errors found. CHKDSK cannot continue in read-only mode.

  Then I tried to reassign the drive letter of the F to h: the display shows the file system is "RAW and the status is healthy, etc."  He doesn't see this as a NTFS format, even if the chkdsk identified it in this way with the correct volume lable, so I know it was to see the right player.  I almost all still on my coomputer - this backup is material that I could go back more old backup drives, but it's the best version of consolicated of my automatic backups of Win 7, so I didn't it wouldn't be pretty.  Am I out of luck?  Is this drive Kaput

  and should I give up on this?

  Thank you

  Hello
  I suggest you contact the manufacturer of the USB to the backup drive then try formatting the USB and check if the problem persists.

• Error: "CHKDSK cannot continue in read-only mode" and "an unspecified error has occurred (766f6c756d652e63 3f1).

  I'm trying to run a CHKDSK on my hard drives. Whenever I try to do "chkdsk C:" or any other volumes (internal or external) invites of high command. I had

  "This type of file system is NTFS.

  Errors found. CHKDSK cannot continue in read-only mode. »
  (That's all I get, nothing in between)

  I have three internal volumes C: D; and E:. Running chkdsk on a volume any returns "CHKDSK cannot continue in read-only mode. Run with / f on C: will check the disk (no error) is restarted. Run/f on any other volume, I had "an unspecified error has occurred (766f6c756d652e63 3f1).
  Has received the same error in recovery mode, safe mode, using the account administrator or UAC disabled.
  Also got same error when you try to chkdsk on all external hard drives.
  I have formatted my E: and ran chkdsk on an empty volume, got the same error.

  Defrag works OK without any problems. External hard disks can be verified (no error and the bad sector) to another computer (win7 pro x 64).
  My external hard drives can be ejected without any problem. But ejection always fail after running "chkdsk /f.

  This computer is win7 pro x 86.
  Installed software: VMWare workstation 7, Microsoft Security Essentials, Visual c# 2010 express, Office 2003, Daemon Tools. DropBox

  Please help me to solve the puzzle.

  Thank you
  Hello

  After some debugging, I found that the ifsutil.dll reported an exception 'divided by zero.
  Finally I found that there is a fix from Microsoft for my netbook CPU (AMD C60).
  A Chkdsk command fails with an error not specified on a Windows Server 2008 R2 or Windows 7-based computer that uses a low frequency CPU AMD
  http://support.Microsoft.com/kb/2502789
  This fix solved my problem.

• Errors such as: CHKDSK cannot continue in read-only mode... won't let me install the new update for the McAfee antivirus program

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Contact the McAfee Support.

• Get the error "Windows cannot be installed to this disk" when you try to install Windows 7 after Ubuntu was installed on the desktop computer

  So I installed Ubuntu 12.04 on my newly built office. I didn't like, so I had windows 7. I started Windows, and choose to perform a custom, Setup since I did not have before windows. Now, here's the problem, is not letting me install on my drive. I get the message: Windows cannot be installed to this disk. the selected disk is a MBR partition table. on EFI systems, Windoos cannot be installed on GPT disks.    Is my previous installation of Ubuntu, the cause of this? How can I resolve this problem and install windows7?

  GParted allows to format the disk, and then try the installation again.

  Operating instructions GParted: 9 steps - wikiHow

  http://gparted.sourceforge.NET/LiveCD.php

• Firefox 5 works but after 6 installation I get this error when you try to run it: check the details below...

  Firefox 5 works fine, but as soon as I install 6 and try to run it, it gives me this error msg:

  "XML Parsing Error: undefined entity location: chrome://browser/content/browser.xul line number 233, column 5: key-^ =" "< =" "id ="key_scratchpad"keycode =" & amp; scratchpad.keycode; ' modifiers = "Shift" p = "" > < / key > ""

  He also said during installation that it can not find updates for Java and Skype extensions.

  If this does not work in mode without failure, then disable all extensions and then try to find out who is the cause by allowing both the problem reappears.

  • Choose "Disable all add-ons" on issues to troubleshoot Firefox in Safe Mode to set window to disable all extensions.
  • Close and restart Firefox after each change through "file > exit ' (Mac: ' Firefox > leave";) Linux: "file > exit ')

  Remove extensions that do not have a button in the extension manager are installed by other programs and should be disabled or updated via this software.

  You can uninstall and remove extensions of the Java Console, you do not need to run Java applets.

  See:

  • http://KB.mozillazine.org/Java#Multiple_Java_Console_extensions

• Error 0x8004231F when you try to run back to the top

  I tried some things proposed for this error msg, but my HP Recovery is still red - only 8,01 MB of 5.09 GB free space.  The msg comes not long after the backup starts.  There is nothing in the trash and I uninstalled nearly all unused files.

  Hi Diana,

  There are two connected problems here and I tried to solve the easier one first.  My first problem is your point No. 1 - not enough space on the backup location (HP recovery).  I get a popup telling me that I have a disk on HP-recovery space, even if I deleted all external files.  For this reason, I tried to make a backup on DVD, which is when my second problem - the error msg on there is not enough storage space shadow.
  I had checked the wires for the solutions to the problem of the second and did something else at the cmd prompt, which checked for problems.

  If I do as you suggest won't that make my too big storage?

  I'm not good at this computer stuff.  Why can't I just remove everything that is in the recovery of HP?  I don't know what happened to suddenly move the red bar.  HP-recovery is an automatic backup there are too many things I don't understand.

  For the moment, I can't afford to pay to get Microsoft to fix the problem.  It will go well if I wait and do nothing, for a month?  Or should I try what you suggested?
  What

• When you try to run chkdsk, it tells me which cannot be executed, the Volume is in use by another process, but trying to run at startup, I am told that the chkdsk command has been cancelled

  When you try to run chkdsk, it tells me which cannot be executed, the Volume is in use by another process, but trying to run at startup, I am told that the chkdsk command has been cancelled. message also indicates that there are errors.  How can I me then chkdsk to run

  Hello

  See if these two tutorials to help you with this.

  "How to run the check disk at startup in Vista or Windows 7"

  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  "How to difficulty Chkdsk will not run at startup in Vista"

  http://www.Vistax64.com/tutorials/130824-CHKDSK-will-not-run-startup-Vista.html

  See you soon.

• When you try to run Linksys Wireless Network Monitor error: cannot load ProcNICs.dll, Can t Load Res_dll

  Original title;

  Linksys wmp54g & windows vista

  When you try to run Linksys Wireless Network Monitor I get the following errors:

  Cannot load ProcNICs.dll

  Failed to load Res_dll

  Linksys wireless adapter is installed and running properly, but I can't use the application linksys to establish a new network connection.

  Any suggestions?

  Thank you.

  Hello

  I suggest you contact Linksys for assistance:

  http://home.Cisco.com/en-us/home

  Linksys Support link:

  http://homesupport.Cisco.com/en-us/support

  I hope that helps!

  If you need help on Windows, please keep us informed.

  We are here to help.

• When you try to run a system recovery I get this error: cannot start Windows. A recent hardware or software change might be the cause. OxcOOOOOOf

  When you try to run a system recovery I get this error; OxcOOOOOOf

  Original title: error OxcOOOOOOf

  My laptop crashed. I used my initial recovery to start. I get a message from Windows Boot Manager as follows:

  Windows could not start. A recent hardware or software change might be the cause. To solve the problem:

  1. Insert Windows installation disc and restart your computer.
  2. choose your language settings, and then click "next".
  3. click on "Repair your computer."

  If you do not have this disc, contact you system administrator or computer manufacturer for assistance.

  File: \Windows\system32\winload.exe

  Status: OxcOOOOOOf

  Info: Seelected entry could not be loaded because the application is missing or damaged.

  It does not work. Suggestions and no, I have not modified before the crash.

  I loaded my recovery disk for my 32-bit home edition of vista Hp pavilion dv6700 cto entertainment lapt top and after going through the recovery process I just get this mechioned of the screen in the original question. How ever during my recovery process never got far enough to enter my product code, he asked just a two disc and disc supplamentry and then gave me a blue screen black for a minute or two then rebooted and showed the failure of start OxcOOOOOOf screen... what should I do?

  Hi Anthony206,

  Since you've already tried to use the Windows Vista recovery disc has received from the Original Equipment Manufacturer (OEM).

  From now on, you can only contact OEM for the use of the recovery feature.

  I hope this helps.

• 5 error message when you try to run gimp - 2.18.16 - Setup could not create the directory

  5 error message when you try to run setup.exe gimp - 2.18.16 after downloading... it reads:
  Setup could not create the directory
  c:\Users\DEBSWO~1\AppDate\Local\Temp\is-IKDP5.tmp ".
  Error5: Access denied
  In the Temp folder under Security I have:
  'SYSTEM' with full control
  "Administrators" with full control
  "Username" with full control
  All of which is listed in the permissions, but the box for'Include the permissions that can be inherited from the parent to this object "below is checked but not really dim so that you cannot check or uncheck the box?"
  The two latest downloads gave the same error message.

  Thank you for your time.
  Debbie

  I suggest you do this:

  1. click on the start planet.
  2. type cmd.exe in the search box.
  3. press on Ctrl + Shift + Enter
  4. click on "run as Administrator".
  5. type the following commands exactly and press ENTER after each:
  takeown /f "%Temp%" / r

  Cacls "%Temp%" / t/c/g "%nom user %": F System: F

  (Enter Y when you are prompted "Are you sure?")

• Error code 0 x 80248014 when you try to run MSE Update on Vista 64 bit OS

  Tomb guard Windows Update crashes when you try to run the Service Pack 1 for Vista 64 even if it seems to have installed service pack when I view installed updates.  Update the window continues to show the service pack update according to availability.  So far, I ran it three times and he shows as installed three days in a row, but he does not appear in the properties view and continues to show an available update when I check for updates.

  It's a little confusing because the error code 0 x 80248014 appears when you try to update to MSE, so there seems to be two issues.  The MSE error one and two, the apparent success of the installation of the Service pack 1 for 64 bit Vista Home Premium but not appear in the properties view and always appear when checking for updates, even if each attempt to install appears to be successful.

  Hello

  Run the system update tool

  http://Windows.Microsoft.com/en-us/Windows7/what-is-the-system-update-readiness-tool

  Retry the update

  Reset the Windows Update components

  http://support.Microsoft.com/kb/971058/en-us

  Error MSE - which describes the boots s. is what will do the above tools.

  http://answers.Microsoft.com/en-us/protect/Forum/MSE-protect_start/error-code-0x80248014/3c3f7fca-F9E0-4D50-afa2-63acab6fb163

• Error message: "the version of this file is not compatible with the version of Windows that you are using", when you try to run an old ms - based back program in Win-7 Ultimate 64 bit.

  Original title: program compatibility Application Applications App Apps game games Legacy Crash crashes Hang hangs

  I get this message when you try to run an old MS-DOS - based program in Win-7 Ultimate 64-bit.

  "The version of this file is not compatible with the version of Windows you are using. Check your computer system information to see whether you need a x 86 (32 bit) or x 64 (64-bit) version of the program and then contact the software publisher. »

  I understand that I am under a 64 bit OS, but is it possible to get this program to run? I was wondering if anyone has tips :)

  Hi Bcopeland,

  Thanks for posting your question in the Microsoft Community.

  Based on the information, you are trying to install and use an old ms - dos program based in Windows-7 Ultimate 64-bit.

  The problem is a software that was created for Windows 95, 98, and Windows XP has no way to work correctly with an operating system that didn't even exist when the software was written. However, the error message you get normally means that you have a 32-bit software that you are trying to install on a 64-bit system.

  You can check the compatibility of the program with Windows 7, in the Compatibility Center.

  Compatibility Center

  If the program is not compatible, then you try to install and run the program in compatibility mode.

  a. click right on the program.

  b. click Properties.

  c. click on the tab compatibility.

  d. Select run this program in compatibility mode and select Windows Vista or whatever to use the system, the program was executed successfully.

  Here is an article that gives you more information on this:

  Make older programs in this version of Windows

  If the problem persists, you can get in touch with the software vendor to see for the latest version of the program to use the same system of 64-bit Windows 7.

  Hope the helps of information.

  If you need assistance in the future to resolve any issues related to Windows, post your query and we will be happy to help you.

• Error when you try to run an application that worked when built with 8.6

  I have a simple program that I wrote in the 8.6 version that I've never had a problem generation and execution of applications built with it to 8.6.  Two weeks ago, I got 2009 by mail because we had very recently purchased 8.6 and I get errors when you try to run an application built with the same code using 2009.  The error relates to the Mean.vi.  He claims that he can't find it.  The error I get is as follows:

  Error loading VI 'NI_AALBase.lvlib:Mean.vi '.  LabVIEW support 3 error code: could not load façade.  I don't have access to the front panel of this vi, so I wonder if there is a problem with the runtime and not my code.  Please answer as soon as possible because it will quickly start to the impact of my calendar.  Thank you.

  Hello!

  The same problem ?

  I talked with my local OR technical support team. The application now works without any problem.

  Rule of thumb: when creating a Setup program do not forget that the option "Run Time Engine xxxx" in the category "Other installers" is selected despite the fact that the runtime is already installed.

  Best regards.

• Get "communication error with kernel" message when you try to run a virus scan program

  Get "communication error with kernel" message when you try to run a virus scan program

  Hello

  What antivirus do you use?

  Follow the steps in the article mentioned below and check if this solves the problem.

  
  The error message "error communicating with kernel":
  http://KB.eset.com/esetkb/index?page=content&ID=SOLN2280