When I try to turn on my PC it reads windows not load correctly

Similar Questions

• When you try to turn on my computer which has windows vista, I get this error code '! 0 * c0190036! 535/95417 (explorer.exe)

  When you try to turn on my computer which has windows vista, I get this error code '! 0 * c0190036! 535/95417 (explorer.exe)

  Hello

  -Remember to make changes to your computer, after which the issue started?

  I would recommend that you follow these steps and check if the problem persists.

  Step 1:

  Start your computer in safe mode.

  Start your computer in safe mode
  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode
   

  Step 2:

  If the computer starts in safe mode, there must be a third party software that is causing the problem to occur, this is why I suggest you put your computer in a clean boot state.
   
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  
  Note: Put your computer in normal mode (step 7).

  Step 3:

  If you haven't already done so, I would say doing a full scan on your system.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

• Windows Defender does not work. When I try to turn it on, I get the message "not responding".

  Original title: Windows Defender

  I have Windows Vista and my Windows Defender will activate/doesn't not work.  When I try to turn it on, it responds by saying: 'it is not responding' and stops automatically.  I tried to re - install & who did not work.  Any ideas.

  Hi lskdjfoie,
   
  What have you tried to reinstall? Windows Defender or other programs?
   
  I suggest the following steps and check.
   
  Step 1:
   
  Usually if you have a third-party security software installed, Windows Defender would not work. I would temporarily disable all security software and check if the problem persists.
   
  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Firewall-on-or-off
  
  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software
   
  Note: Antivirus software can help protect your computer against viruses and other security threats.  In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.
   
  Step 2:
   
  If this does not help, I would say you scan SFC on your computer and check if Windows Defender works fine.
   
  Step 3:
   
  If none of the steps helps create a new user account and check if the problem persists.
   
  Let us know
  Aziz Nadeem - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• When I try to print a PDF file it reads does not

  Is this a problem with the printer/windows or adobe?

  Hicharlesr49424062,

  Open Acrobat Reader DC, go to the Help menu and repair the installation.

  Also check the updates under the Help menu. If any please install.

  If the problem persists, try the solutions listed in this KB doc.   Acrobat and Reader help / troubleshooting PDF printing | Adobe Acrobat, Adobe Reader

  Kind regards

  Nicos

• Hello, I was wondering why my adobe first pro ((when I try to open it)) say that "the application could not start correctly 0xc000007b" I need help as soon as POSSIBLE. Im trying to work on a film, but I can't until I have correct this problem. Help?

  Hello. I need help as soon as POSSIBLE, when click on my first adobe, it says "the application is unable to start correctly 0xc000007b" I need major help as soon as POSSIBLE - does anyone know how to solve this?

  ... 07 b problems http://forums.adobe.com/thread/1355374?tstart=0

• My Mac Pro 2009 gives me only a power button blinks when I try to turn it on.

  My Mac Pro 2009 gives me only a power button blinks when I try to turn it on. External drives turns on but not the computer or monitor. I tried holding down the power button to restart but I still get only a power button blinking and no departures. It is running IOS 10.8.5 and I use it mainly for recording and mixing of music. I use Digital Performer and, sometimes, ProTools. Nothing new has been installed recently.

  fans on, power button flashing says "not enough RAM that works correctly for starting up".

• Equium A60 - 155 clicks when I try to turn it on

  Hey

  I was wondering if any1 could help me. I recently put a toshiba equium a60-155 without a power adapter, also without battery but the store are previding by toshiba as soon as possible. so I put a power adapter and plugged - DC IN light turns green so everything seems good but then when I try to turn it on just click and the keyboard lights flash, then nothing happens - if I hold down the power button everything that just clicks and flashes. is it because I dnt for a battery? -I don't think dnt. any other ideas?

  see you soon

  Josh

  Hi Josh,.

  Your A60 equipped with a pre-installed system or you have set up your system CD provided?

  Your laptop must turn on without the battery, so it is possible that there is no operating system installed for the time being installed.

  Have you had the correct PSU for your A60? Your card must be able to supply sufficient power for the laptop or that it does not start.

  HTH

• 6 iPhone with iOS 9.2 does not and freezing when I try to turn on + WiFi freezes

  6 iPhone with iOS 9.2 does not and freezing when I try to turn on + WiFi freezes cannot allow him. (When I get to start the Iphone by pluging it to Itunes)

  I've done a new install and reset the network settings.

  But always the same questions

  Thanks a lot for your help

  I have the same questions and more from Friday December 11 when I've upgraded to iOS 9.2.

  Device: iPhone 5 s

  Problems:

  -Screen freezes randomly reboot * required (sometimes restart by the camera itself)

  -Sometimes device reacts very slowly on the command (or even then restarts)

  -For the most part within the first hour when used, sometimes immediately (after restart)

  -Cannot slide or apps to react when I touch

  -AssitiveTouch on, keep available however to move and opening, but no order accepted when the screen is in gel

  Resolution of problems so far:

  -Reset all settings (no result)

  -Backup on iTunes (11 dec)

  -Erase content and settings and restore the backup to iCloud (10 Dec *) (no result)

  -Erase content and settings and restore the backup of iTunes (11 dec) (no result)

  -Tried with the new iPhone camera 6 and restore backup icloud (unsuccessfully; restore hangs at "1 minute remaining")

  -Tried with the new iPhone camera 6 and restore backup of iTunes (no result: same freezing questions reappear)

  Conclusion date: is not a hardware problem (device), but one software: combination of the configuration (such as backup) and the new iOS 9.2.

  By the way: I guess that not possible to restore 9.1 on the device.

  The new iPhone 6 initially contained iOS 9.1, but then did not 'see' backups, because they were made from a 9.2 iOS device.

  So I had to first install the iPhone 6 as a new iPhone, upgrade to iOS 9.2 and then I was able to reset and restore the backup (with no good result, as described above).

  *) restarts: hold Home-button on/off-button simultaneously for 10 seconds

  backup *) in the form of clouds 10 Dec worked without problem on iOS 9.1.

  I will continue to investigate on removing the apps installed a year or two, see if that generates the result.

• A small flag appears on the bottom of my screen that says activate security service Windows, but when I try to turn on it says could not start the Windows security service

  Original title: HELPPPPP

  My computer a little flag in the background with a x... said red it turn security service windows, but when I try to turn it on... it said windows security service cannot be started :/

  Hey ChelseaHarris,

  Take a look at two responses in the thread below the link to see if they allow the Windows launch security service:
  Could not start the Windows Security Center service.

  If these steps do not help, try to run a full scan using the Scanner from Microsoft which can be downloaded using the link below:
  Microsoft safety scanner

  Hope that helps.

• When I try to turn on "Windows Defender" I get an error message "ox800106ba".

  Original title: error 0x800106ba.

  When I try to turn on "Windows Defender" I get an error message "ox800106ba".
  How can I activate the Windows Defender?

  Hello

  If you use Norton, AVG, Avira, Microsoft Security Essentials, McAfee, etc. the default action is for Windows Defender must be disabled, that these AntiVirus programs have their own Antispyware Applications.

  There is nothing to worry.

  Using both programs at the same time can cause system conflicts, etc.

  If you are using one of the above AntiVirus programs, this Information from David O - Support Engineer shows you how to manually enable Windows Defender (disregard information from uninstalling; not possible in Vista):

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-security/how-do-i-manually-start-Windows-Defender-in-Vista/dab845b2-9ba5-47F3-9518-c4c6781e7d5b

  "Go to start, Control Panel, Administrative Tools, Services. Look for Windows Defender.

  Right click and select Properties , ensure that Startup Type is automatic.

  Once modified, click apply and OK.

  Quit and restart your computer. Check the back take the same path to confirm that Windows Defender has started"

  .

  If you want to have additional protection against malware using the version FREE of Malwarebytes AntiMalware:

  http://www.Malwarebytes.org/products/malwarebytes_free

  And for now, change startup Vista programs without using Defender, use one of these methods:

  "How to use MSCONFIG in Windows Vista"

  http://netsquirrel.com/Msconfig/msconfig_vista.html

  Or the program Autoruns for FREE:

  "V11.21 Autoruns for Windows"

  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902

  See you soon.

• When I try to turn on the Windows Firewall, I get a sign message that says "Due to a problem not identified, Windows cannot display the firewall settings."

  When I try to turn on the Windows Firewall, I get a sign message that says "Due to a problem not identified, Windows cannot display the firewall settings."

  I found another thread in Microsoft Answers relating to this problem, but who said to go into Services and see if the firewall is configured to automatically start.  However, I can't find a Windows Firewall item in the Services Menu.

  I have the PC Tools Spyware Doctor antivirus.

  I had to do a complete recovery system... which sets just need to make sure that you back up your files.

• "" My Windows J.4 Center repair center is currently disabled but when I try to turn it on I get the error "cannot be turned on.

  original title: Security Center

  I had a virus to infect my computer but I'm to remove by doing the scans. I can't solve the problem of after-sales service. "" My Windows J.4 Center repair center is currently disabled but when I try to turn it on I get the error "cannot be turned on.

  Hello Barbaram1,

  Use the Windows key + R on the keyboard or click on start, select run.
  In the run box, type services.msc
  Click OK.

  Make sure that the Security Center service is enabled and started.
  Probably, you will need to click Start to start the service.
  The Startup Type should be automatic.  The status should be started.

  Let me know what happens. If the problem persists, it may be that there are residual questions of the malware infection.

  Councillor of State & progress.

  Maurice Naggar ~ MS - MVP

• When I try to update to Firefox, I get a window saying that it cannot be loaded because I don't have all the necessary permissions. What do this mean and what do I do?

  When I try to update to Firefox, I get a window saying that it cannot be loaded because I don't have all the necessary permissions. What do this mean and what do I do?

  If he has problems with the update or the permissions then simpler is to download the full version and trash the version currently installed to do a clean install of the new version.

  Download a new copy of the Firefox program and save the file on the desktop DMG

  • Firefox 6.0.x: http://www.mozilla.com/en-US/firefox/all.html
  • Trash the present application Firefox to do a clean (re-) install
  • Install the new version you downloaded

  Your profile data is stored in the Firefox profile folder, so you will not lose your bookmarks and other personal data.

  • http://KB.mozillazine.org/Profile_folder_-_Firefox

• Safari iPad links work do not. Is froze safari when I try to open the link in a new window.

  I use the iPad 2 with iOS 9.2.1.

  When I try to open a link it's doing nothing.

  When I try to open this link in a new window, Safari, Safari freezes.

  Then, I use Firefox. The links in the same window do not work, but they work fine when it is opened in a new Firefox window.

  Can you help me?

  A chance we can get an answer to this problem?

  Thank you

• When I try to install Firefox, I get an error "could not open the output file. I used Firefox before and it doesn't work anymore, so I uninstalled. Cannot re - install now.

  When I try to install Firefox, I get an error "could not open the output file. I used Firefox before and it doesn't work anymore, so I uninstalled. Cannot re - install now.

  This has happened

  Each time Firefox opened

  I tried to download firefox.

  User Agent

  Mozilla/4.0 (compatible; INTERNET EXPLORER 6.0; Windows NT 5.1; SV1; AntivirXP08; GTB6.3; .NET CLR 2.0.50727; MS - RTC LM 8)

  When you click on the download link on GetFirefox.com, you should be asked if you want to run or save the file. If this situation occurs when you try to run the download, try instead to record and put the file on your desktop or in a similar place, where you are certain that you can find.

  When the download is complete, try double-clicking on the downloaded file in the normal Windows Explorer (browse your way to the file from the desktop). This should start the installation.

  If, in the Explorer window, you notice that the file seems to be missing the Firefox icon orange/blue, right click the file and select Properties. The image should look like the attached picture (except that mine is in Danish, but that is irrelevant) if saved correctly - if it don't look like this, would you please describe the content or attach a screenshot of the box. Especially what it says under "File Type" - it must be 'program '. If this isn't the case, will have to focus on what could be the problem here.

  A bit off-topic, your Internet Explorer seems to be quite a bit outdated (IE 6, where the current version is IE 8), so I highly recommend that you try to run Windows Update to get your system up to date. Is it as a society (such as a thin client Terminal Server computer) system, this is not possible, and most likely, your system administrator will have to help you.