When the power settings are on anything except power save speakers make a hissing sound

Similar Questions

• the problems of sound, lost power when the power came back... no sound

  I have a Creative x - fi titanium sound card to sound problems, loss of power... when the power came back... no sound... Please help!

  Maybe the following link would provide a few ideas:

  Windows 7 - no sound in Windows
  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows
  (valid for XP - Vista - 7)

• My laptop can open internet explore properly, the cursor may work when you tap the address space to type a Web site, but the site it does not point to the search space to find anything except the right button

  My laptop can open internet explore properly, the cursor may work when you tap the address space to type a Web site, but the site it does not point to the search space to find anything except the right button. What is the problem? Harry

  When you try to search it's inside Windows or Internet explore?
  When is this last work fine?
  You did changes to the computer?
  Has it worked before, then you can try to run the system restore and check if that helps

  ;)

• Pagefile.sys has completely disappeared. It started when the power failed and my computer crashed.

  My pagefile.sys has completely disappeared. This all started when the power failed and my computer crashed.
  I get the message that he was away, I went to the performance and settings and tried to change custom settings & re-start.

  No matter what I do, nothing works. I lost several hours of visiting sites for tips and nothing seems to help.

  I was told when re-boots WinXP it creates the new file pagefile.sys and I should delete the pagefile.sys file may be corrupted on the C drive.

  So I put the folders to show hidden files and delete pagefile.sys. I have re-set and tried to recover with no success.

  There is now absolutely no pagefile.sys on my C drive. Anyone know how I can get back my pagefile.sys?

  I want to get my virtual memory works again?

  Thank you very much in advance!

  I'd start first with the chkdsk/r.

  Don't forget - if you have a factory installed recovery Partition, fixmbr will scan it as the Master Boot Record that written XP will equal not the MBR installed by the factory, so first run chkdsk /r (did I say that already)?

  Here are some instructions:

  http://pcsupport.about.com/od/fixtheproblem/SS/RCONSOLE.htm

  Where people have no XP bootable media, here are my instructions:

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget.

  This is not the same as recovery disks that might have come with the acquisition of the system store.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  http://www.mediafire.com/?ueyyzfymmig

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD:

  http://www.ImgBurn.com/

  When you install ImgBurn, DO NOT install the Ask toolbar.

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

  A good idea before you start things must first verify the integrity of your file system by using the chkdsk command.

  In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.

  Running chkdsk is fine, even if he finds no problem.  It won't hurt anything to run it.

  Assuming your boot drive is C, run the following command:

  CHKDSK C: /r

  Let chkdsk finish to correct the problems, he could find.

  It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

  You must run chkdsk/r again until it finds no error to correct.

  Remove the CD, and then type "exit" to exit the RC and restart the computer.

  You have not to set the BIOS to boot the disk HARD since the CD won't be.

• NB200 abandoned wireless connection when the power cable is plugged

  ALL ideas welcome, my notebook NB200 drops Wi - Fi when it's attached power alternative, on another forum, someone suggested I could change the power settings to avoid this problem, but not how, all ideas welcome, thanks
  kazz45

  > I found the power options, but all that it gives me a choice of power management, which is energy-saving Toshiba which corresponds to the current setting, I see nothing wireless on the tabs it?

  You must discover the power plan that is used when the power adapter is attached.
  Then, you click on change the power plan settings

  New window would be open where you will find an extra option called change advanced power settings

  Now you will see further options. Scroll down the settings of the wireless adapter and make sure both options are set on the performance

• Satellite Pro L500 - stops when the power cord removed

  Toshiba Satellite Pro L500 stops when the power cord is removed even with the battery to 100%. I removed the battery and all the indications associated with battery answer correctly. For example turns off, Toshiba Health Monitor also indicates when the battery is removed. If installed Health monitor indicates that the battery is at 100%.

  Someone please help. I have not installed anything new.

  Hey,.

  For me, the matter is clear: the battery can't hold a charge so the laptop will be shut down because it has no power.

  I think you need to replace the battery with a new one and you can get a provider of service authorized in your country. Simply contact the guy and ask that they can tell you how much it would cost.

  You can find a list of all FSA here:
  http://EU.computers.Toshiba-Europe.com > support & downloads > find an authorized service provider

  Good luck! :)

• Satellite Pro L20: battery not charge when the power adapter is connected

  Hello

  all advice appreciated.

  I had a Satellite Pro L20 for about 18 months. Recently, battery does not charge when the power adapter is connected. The battery light starts yellow (which means more liberated, I think?), then will both green, the machine sat for awhile. However the ACPI often said that AC is "offline."

  There are two recent occurrences that coincide with this problem, I try to eliminate:

  1. my friends rat chewed by the feeder for pets! Power is Mobile OK insofar as he fled sector - the rat seems to have simply chewed by the outer cover (I see some threads, but I think that is just a shield, although I'm not an electrician).

  2. I put the laptop in hibernation for the first time. That seemed to mess up the system a bit, which was what initially drew my attention to the problem. This question is a bit complicated because I'm under Linux (Xubuntu).

  I updated the drivers etc from windows when I bought the laptop. Never had any problems until now and have been running linux for centuries. Also, I have mainly the laptop the power supply turned off, but do not remove the battery (is that really a problem these days?)

  I obviously need to replace the adapter, but is - it is likely (and how I can check) that the battery was borked until?

  see you soon
  Chris

  First, please check if the other are lit.
  If the AC led and power led are on the adapter sector is ok and it provides the power to the laptop.

  > The battery light starts yellow (which means more liberated, I think?), then will both green, the machine sat for awhile
  If the battery LED is yellow, this means that the battery is not fully charged and if the Green led changes then recharging is caught and the battery has been recharged.

  So I really don t see any problems with the charge process.

  Maybe the battery is old and so you cannot use it for an extended in such a case only the replacement of the battery could help.

• Satellite L655 - questions turn on when the power adapter is unplugged

  Hello

  I have a problem with my new Satellite L655. When the power adapter is disconnected and wireless is disabled, the laptop can turn on for less than a second turn it off again. OR turn 'power' and 'Wireless' turns on, but black screen and hd light; After startup bios of 30-40 seconds, the wireless light turns off and hd lights; OR turn on normally;

  Toshiba has changed the motherboard a few days ago, but the problem persists. Update BIOS. My laptop is the only one affected

  Thank you in advance,
  Maurizio.

  Hey Buddy,

  > Toshiba has changed the motherboard a few days ago, but the problem persists
  So have you contacted already technicians again? You must tell them that the problem is still not resolved and it must be another reason for this problem. Then get in touch with technicians again to clarify this issue.

  Have you connected external devices while laptop is turned off?
  -Online if yes remove each of them.

  Load default settings in the BIOS?
  -Online if it is not this. Enter in the BIOS, and then press the F9 key to load defaults.

  Otherwise, it would be time to service as I have already written. It must be a nuisance material

• Manufacture of extreme dual band 802.11 airport "buzz sound" when the power supply is attached

  Hello

  which is very probably wrong with my Airport Extreme?

  My Airport extreme dual band 802.11 done "buzzing" sound when the power supply is attached. The sound disappears immediately when power is disconnected and begins as soon as you connected again. It started two weeks ago, and it's really annoying.

  THX,

  Laura

  Most likely, the question is a bad capacitor in the diet. These can fail and are, unfortunately, not serviceable by the user... unless you have experience with electronic repair. You can try Apple, but chances are that you will have the best chance to get a replacement from another source, such as Impact Computers & Electronics or eBay.  I'm sorry.

• Power problems: computer turns off when the power supply cord is unplugged.

  original title: power problems: computer shit turned off when the power supply cord is unplugged.

  I have a HP Pavilion dv2000

  Windows vista home premium/sp2

  AMD Turion (TM) 64/2 1.80 ghz processor

  1 GB memory

  32 bit operating system

  I have 2 problems with this laptop.

  !. I have lost the power cable and bought an expensive one online step (model: PA-1650-02 c. input 100-240v 1.5 put out a(1,5A) 18.5V 3. 5 = a)

  When I first plugg cord battery charge light came on the balance, then he started to come on and outside.

  now its completely off, even with the power cord plugged in. on the lower right part of the screen its showing that cord is connected to the power supply and the battery is fully charged, but as soon as I unplugg the power cord or remove the computer cut right away.

  the second problem is that the left mouse botton does not work, the work aside right very well. I went in the proprties to put it right, click on to, but who does not work either. I've updated the drivers but still nothing.

  Any help will be greatly appreciated.

  Hi aloum,.

  (a) what kind of mouse you are using?

  (b) the left button of the mouse seems to be stuck or it does not meet the click? This only happens with certain applications?

  Step 1: Test the mouse on another computer or another mouse on the test computer

  To determine whether the mouse or the computer is defective, follow these steps:

  1. test the mouse in question on a system that works, you know. If the problem appears to follow the mouse, you may need to return or replace the mouse.

  2 test a mouse you know is working on the computer in question. If the problem seems to stay on the computer, then the problem is most likely related to the software.

  In regard to the battery not holding charge

  Battery problems are often associated with the battery itself. If you encounter this problem, contact your mobile PC manufacturer. If you purchased the battery separately from the notebook computer, contact the manufacturer of the battery.

  Troubleshooting battery problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-battery-problems

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• The screen of my laptop turns off when the power cable is connected. If this isn't the case, connected screen is ok. No idea why?

  The screen of my laptop turns off when the power cable is connected. If this isn't the case, connected screen is ok. No idea why?

  Original title: clear the display

  Click Start or press the Windows key and type power can locate the power to change recording settings in the section of the Control Panel from the list above and click on it. At the opening of the Power Options pane, click choose when turn off display available on the left side.

  

  Choose a new setting for brightness in the drop down menu on the battery . Look at all the other parameters that you feel you want to modify, and then click save changes in the lower right to apply the options you have selected energy saving.

  You can now close the Power Options pane when you return.

• Portege M500 cannot start when the USB ports are loaded

  We have a M500 that recently seems to be affected by start-up problems when the USB ports are loaded with things like KB and Wireless Mouse USB external adapter.

  When these ports are occupied at the start, all the usual tools seem do not load and the associated icons do not appear in the toolbar at the bottom of the screen. The machine in question XP Professional and has 2 GB of RAM. The machine software is generally updated. Machine seems to start normally when the USB ports are empty.

  Once completed a successful boot USB ports can be occupied and the machine will then seem to operate normally.

  Any thoughts?

  Thank you.

  Hello!

  In your case, I would do a BIOS update and also the chipset driver.
  The two you can find on the Toshiba site. I m not sure but I think you have a model for Canada:
  http://www.Toshiba.ca

  Have you tested the devices USB on another computer laptop or PC? Maybe the problem is the keyboard and/or the mouse and not the laptop.

  Good bye

• HP Color Laserjet M277n MFP: How to use the black cartridges only when the color toners are empty

  Hello team HP,

  I recently bought a HP Color Laserjet MFP M277n I printer I print black & white user only and really don't need color prints. How to set the printer options to print only black & white? How can I replace only the black cartridge when the color cartridges are empty? How many prints (approximate), we can take by toner?

  Kind regards

  Christèle

  Hi @Pavumba,

  Welcome to the Forums of HP Support!

  I understand you're wondering how to use black ink only on your HP Color Laserjet M277n MFP printer. I would be glad to help and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I see that you wonder if you need to replace the color cartridge when it is low. This printer is a printer AIO, therefore, you need to replace the ink cartridge when it becomes too weak to be able to resume printing. However, if you print mostly in black, you can configure a preset black only to print in black and white. This would help reduce the use of the color cartridges.

  NOTE: Composite black - for black and white images and photos, a mix of colors called 'composite black' can be used to achieve the quality significantly improved picture and soft gray tones that can be achieved with only black toner. For users who want to print images using just black toner, many HP printers color customer offer configurable options allowing the client to print using only black toner. For example, by selecting "print in grayscale" in the printer driver Specifies print using black ink only. For more information about the use of the toner cartridges, please see this article: how the Toner is used.

   

• The HP printer won't turn on or respond when the power button is pressed

  The HP printer won't turn on or respond when the power button is pressed

  The HP printer won't turn on or respond when the power button is pressed

• What happens when the error report are sent to Microsoft from my computer?

  I received a call from a Clayton asked for a Windows Service Center. He called about the error reports that were sent from my computer to Microsoft. He gave his phone number as 91 9008 37 23295 in Calcutta, India. If this has nothing to do with Microsoft or Windows?

  John is correct.  And to answer your direct question: "what happens when the error report are sent to Microsoft from my computer? -Not much.  If these reports are used at all, they are used for the statistical analysis and do not respond to individuals.