Where is the Scanner Twain driver?

Similar Questions

• Where is the SATA AHCI driver for the NB200 notebook?

  I searched the forum and I know that I should integrate the drivers under XP with Nlite, but I Don t find the NB200 AHCI driver in the driver download section!

  I don't know much about your model, but if you publish the chipset model, I'll try to find it for you:

  http://forums.computers.Toshiba-Europe.com/forums/Ann.jspa?annID=38

• How can I download hp scanner twain driver for hp photosmart c8180 all-in-one?

  I have windows xp

  utilities for hp said I had need of "HP Twain Scan and the HP Scan Flow Manager" I download the latest software, but doesn't always solve a problem.

  Hi Freezzee,

  The full software and driver on the link below contains the two drivers to scan. You will need to select your operating system and then download the drivers and full software features.

  http://h10025.www1.HP.com/ewfrf/WC/softwareCategory?CC=US&DLC=en&LC=en&os=4063&Product=3204788&softwareitem=MP-76036-1&sw_lang= &

• Where is the "PCMCIA Bus driver" and how to uninstall it?

  The menu Tools and Information on the performance said that "these drivers are causing Windows to resume slowly"-

  Name: PCMCIA Bus driver

  File name: pcmcia.sys

  Feature: Texas Instruments controller CardBus PCI - 8 x 12/7 x 12/6 x 12

  Other posts on this forum, I understand that it is safe to uninstall this driver if it is not in use.  Unfortunately, I can't find.  I looked in Device Manager (there are two other devices Texas Instruments listed - or one has the correct device name).  I also looked in programs and features and menu of start-up of sysconfig with no luck.

  My computer was crashing regularly about 10 minutes after waking up from hibernation.  My hope is that this driver uninstall will fix the problem.  Any help would be greatly appreciated.

  It seems that the "Texas Instruments PCIxx12 Integrated FlashMedia Controller" device is the device you are looking for (the first two digits in 8 x 12, 7 x 12 and 6 x 12' is reduced to a "xx12' in the name of the device for simplicity). Try to disable it and see if your problem is solved.

  Note: This device looks like it controls a card reader. It is a decive integrated on your CPU, where the floppy drive which reads flash memory cards (for example: SD card, Memory Stick, xD card, etc.).

  Rifdhan

  If this is your answer, click on "Mark as answer" below. If it's useful, click on "Mark as useful" on the left.

• Use the Interface of the Scanner in gray

  Does anyone know how I could change things permanently in a scanning interface? I'm on a desktop PC Windows 7.

  When I select file > create > pdf from scanner > scanning custom, and then select the Options button next to the scanner, the User Interface appears dimmed. I really want to permanently change the defaults - dpi, color, paper size, etc.. Is there another way to do this in Acrobat DC?

  Thank you.

  Hello

  I expect you are scanning with WIA scanner drivers. Interface scanner option will always disable to WIA drivers.

  If you want to enable this option, you can download the scanner TWAIN drivers, site of the society of the scanner. For TWAIN drivers, these options are by default turned on and you can set any value of DPI, color and papersize.

• Where can I find a twain driver for the scanner?

  Original title: twain driver for Windows 8

  After having upgraded Win 8, my scanner has failed. Once verified, the problem come from twain driver. Pls help

  Fixed mine. There is no drivers Windows 8 available on the Canon's Internet site or Windows Update. Follow these steps to install a scanner CanoScan 8400F under Windows 8 x 64 in desktop mode:

  (1) download and install the drivers Windows 7 x 64 on the Canon site.

  (2) launch Manager devices, right click and uninstall any unknown device (?), then scan again for new hardware and drivers Windows 7 x 64 installs automatically.

  (3) download and install the Canoscan Toolbox software from the Canon site.

  (4) run the Canoscan Toolbox software, select settings and click on the reset button to fix the non-working electronic copy, scan, PDF, mail scanner buttons.

  (5) reset.

  The button is restored after the restart. Everything works as expected today. Good luck!

• After the upgrade to El Capitan, I get "the scanner is attributed to ImageCapture. Using the scanner with TWAIN? What to say?

  I have XP Epson-610 and have scanned on it successfully for years. To date, but when tried to open I get the ap scanner, the scanner is attributed to ImageCapture. Using the scanner with TWAIN? ImageCapture does not work on El Capitan? What is TWAIN, a printer-scanner driver?

  Thank you.

  TWAIN is an old scanner interface. OS X now use ICA, Architecture (?) of Capture of Image.

  Never seen this message, but I guess that means Capture of Image is using the scanner, or is configured to use the scanner and it is not necessary for the third party software. You open picture Capture, or did the scanning software provided with the scanner by Epson?

• LaserJet MFP M277dw Pro: How to find the TWAIN driver?

  The program that I use to scan works best with a TWAIN driver. Scanning HP doctor using it seems that both a WIA driver and TWAIN driver are available on my MFP M277 scanner, but the select option shows only the WIA. How can I find the TWAIN driver?

  Analysis of the issues...

  Please try this scanning solution:

  HP extended Scan
  
  FTP://FTP.HP.com/pub/scanners/HPScanExt/HPScanExt.msi
  
  Once it has downloaded and installed, go to start > all programs > HP > HP Scan extended > Run "HP Scan extended.
  
  Let us know.

• HP Deskjet 3050 J610: How to find and download the scanner software and TWAIN drivers

  How can I find the link to download and install the latest software and TWAIN driver.

  My laptop recognize my printer and print documents but does not recognize the scanner.

  Hello

  Plese follow this link to choose the operating system and get the drivers for your printer

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?cc=us&DLC=en&JumpID=reg_r1002_usen_c-001_title_r0001&LC=en&product=4066452&

  Thank you

  I am an employee of HP, these messages are consistent with my knowledge and HP is not responsible.

  By clicking on the star of congratulations in the post helped you to say thanks.

  Please indicate the position that solved your problem as accepted Solution

• Cannot install the scanner (Epson Workforce 500) Windows 7 driver

  I have an Epson Workforce 500 multifunction printer, copier, scanner, fax, which worked well in the past, but the scanner no longer works.

  I tried several times, following the line (and by telephone with a technician of Epson) instructions on downloading and installing the printer updated and drivers scanner Epson.  However, always, the installation stops and the message that drivers cannot be installed (and then restart and try again message appears).

  I was able to get the printer to work by plugging the USB cable to the printer and allowing Windows Installer the driver of the ESC/P-R, but the scanner does not work, and I did all the other characteristics of the available printer.  When I try to get the latest driver via the printer preferences, I get the message that I have already installed the most recent driver.

  More recently, I used the Troubleshooting Guide for the Epson, up to the point where it is said: ' Click or Start and select programs or all programs. "

  Select Epson or Epson printers, select your printer folder, and then select Epson Printer Software Uninstall. »

  When I do this, the program from the start menu does not have the listed Epson printer, or it displays the option to uninstall the printer.

  In addition, when I go into Control Panel, uninstall a program, the Epson printer is not as an installed printer.

  I tried once more to install the driver downloaded from the Epson site package and again, has received the message that the driver could not be installed.

  Then, I used the window update to install all the updates Windows 7, deleted the Epson printer, reconnect the USB cable and restart the computer.  Once Windows has installed the ESC/P-R driver, which she says is the last available.  I'll let it go and just not use the scanner if I can't get this resolved.

  Before you install go to start, make right click on computer, click on properties and the system window will open, left eye for click Advanced settings open then click on the Hardware tab, click installing driver and assigned to the let me select never install Windows update, and save at the bottom. You can set it back by default later if you wish. Now install the downloaded driver, have turned on printer, but do not connect the USB cable until you are prompted.

• Bookmarks in version prior to the 8 - installed the new hard drive - where is the bookmarks file?

  installed new hard drive two months ago - just now to reinstall Firefox - installed new version 8 - need to know where my old favorites would be stored (what file and where)

  The profile is a file that store your personal information in a safe place

  • https://support.Mozilla.com/en-us/KB/profiles
  • here explain how to make a backup of https://support.mozilla.com/en-US/kb/Backing%20up%20your%20information profile
  • here explain how to restore

  https://support.Mozilla.com/en-us/KB/recovering%20important%20data%20from%20an%20old%20Profile

• Portege Z830 - where can I get the new HARD drive

  Hello

  I have problem with my toshiba portege z830 ultrabook.
  My HARD drive died, and I don't know where I can get the new HARD drive.

  I've got guaranteed but I am forgotten registered my cell phone before when I went for repairs not authorized, because my first problem was with the motherboard.

  This motherboard has been replaced for new ones.
  If my warranty is maybe cancelled.

  Well, that's my problem to another.

  What should I do?
  Please help me. I am available to do anything.

  Hello

  I think that you should first check if your warranty is still valid.
  This can be checked on Toshiba Unitdetails page:
  http://APS2.toshiba-tro.de/unitdetails/

  Where the warranty is valid, get in touch with maintainer authorized Toshiba in your country for replacement.

  But as far as I know the Portege Z830 was equipped with an mSATA SSD drive.
  This means that the laptop doesn't support HDD 2.5 common but requires special mSATA SSD drive module.

  In case your warranty is not valid, you will pay for a new mSATA module.
  Replacement should do a service provider authorized Toshiba as well because this replacement is a little tricky on this model of laptop.

• Satellite A300D-16W - where I can get the new display driver?

  Hello

  I have a problem when I installed the driver from Toshiba support. Playng in very slow options of games very slowly.

  When I perform the installation of the ATI support driver will not work correctly. Can someone tell me where I can find the best driver for this video card before I have Vista ultimate that I play in the race driver grid, everything is ok in weak options of course but normally plaing, then I install Vista Home premium and the game of options very low don't work normaly :(

  can someone help me?

  Hello

  On the Toshiba driver page, you can find a display driver for Win XP v8.479 and another for Vista v8.479.1.4

  If you are using Vista, then you must select the v8.479.1.4 driver.
  If you are using Win XP then it must select the v8.479 driver.

  You said that you were able to play this game using Vista Ultimate and driver of Toshiba page. So in my opinion, the driver seems to be OK and should work!

• "Unknown device" USB Barcode scanner, problem with the USB controller driver?

  Hello

  I need assistance with our Barcode Scanners that doesn't work on our newly purchased computers at HP with Windows7 Pro x 64 operating systems.

  The brand and model of the bar code scanner is:

  Datalogic Heron D130 USB.

  When you connect the scanner to a USB port, Windows will try to install this as a HID, but it takes an unusually long time, about 7-8 seconds, to boot the device and install the drivers and appears as an unknown device in windows "devices and printers" and the hand scanner does not work.

  Sometimes when you move the USB back can I sometimes the scanner at hand to be recognized as an HID device or a Datalogic barcode scanner,

  It works fine until you restart the computer.

  After restart the computer cannot detect the scanner Barcode correctly without re - appears as unknown device.

  I suspect that there is a compatibility problem between barcode scanner and card USB controller on the computers.

  I tried to update all the drivers available on the website www.hp.com and same www.Intel.com (chipset drivers) but nothing has helped to solve this problem

  Tried newly bought barcode scanners and "used" barcode scanners earlier who works on other computers, but the problem remains.

  I found a workaround by connection of bar codes in a USB hub, and then plug the USB hub to the computer.  And leave the USB - hub to take care of the communication with the Barcode Scanner.

  in this case, it takes about 2 seconds for the code scanner barcode to mount correctly in windows under the heading "devices and printers" and then works perfectly, even after a reboot.

  I googled after a response after my problem, but it seems I'm the only one who experience this issue. ?!

  Bought more than 40 computers that I have this problem.

  These were bought at different times with two different for suppliers

  Computer model are the following

  HP ProDesk 1 400 P/N5S21EA

  Specifikations:

  http://WWW8.HP.com/emea_africa/en/products/desktops/product-detail.html?OID=6614160#! tab = specifications

  Does anyone have an idea what could be wrong and how to fix it?

  Thanks in advance

  Sincerely

  Robert T

  Hello

  The problem is not power - related.

  We use passive USB hubs that solves the problemon these computers.

  (it also works with the docks, or if you EliteDisplay E241 HP as we thers a usb hub 2 ports inbulit in monitor that works.)

  The problem lies in the incompatibility between the Intel USB controller and the hand scanner, can be connected to USB 3.0

  When you let another usb-controller support in handshakeing (such as a usb hub), it works.

  Datalogic or Intel would like to acknowledge this error.

  Because none of the big companies want to acknowledge the problem or repair, personally chose to switch to an AMD platform / CPU instead of the Intel and now it works fine!

  We get more performance for your money when AMD is usually less expensive to purchase.

  And because of the poor of Datalogic press where they don't even answer e-mail (their only channel for support)

  I chose to stop using their products. I'm going to use another provider / brand of barcodescanners.

• Satellite L650-11F: where are the backup information stored on the HARD drive

  Hello.

  My original Toshiba HDD is a failure and I had to replace it with a new one. I haven't had any recovery DVDs until Windows stopped booting and try to avoid buying one.

  I thought that I copy just my recovery Partition and the master boot record on the new HARD drive which worked well. However I find that this hidden restore partition has only 400 MB and so cannot possibly contain all the necessary information to restore the system.

  I have boot from it, but I don't get any options to restore the default settings. It scans only for problems with Windows, runs a few tests on my records and presents me with advanced options that I can't go because I'm not connected.

  I went searching all about and know that ELSEWHERE THE PARTITION RECOVERY that you still need your Windows partition for recovery work.

  It seems just really stupid because most people will try to restore their default values after damage to their windows (deleted files accidentally or whatever).

  What is the point of keeping a partition hidden with just enough to Prime the system, but then require that certain parts of their partition original windows remains intact in order to restore?

  What I'm trying to know is exactelly what part (files) do I need to restore my computer. I tried to copy the Windows partition on the new disk but its too damaged and he'll take it apart if I try to copy some files or to copy directly (using linux dd or ddrescue).

  I am able to copy some of the unique files, so with little chance I might be able to copy everything that I need. I can't copy the part of the Windows folder however.

  So any1 know where the backup information is stored or has other ideas?

  Thank you in advance and please excuse my bad English.

  Hello

  At first, I must say that your biggest mistake was not not to create recovery discs. With these discs you didn t now have a stupid problem.
  Anyway, in my opinion, only option for you is now buy original Toshiba Recovery disk and install Recovery on the new HARD disk image.

  I put t know how to start the discussion with you and try to offer some answers. Is Toshiba doesn t create recovery CD/DVDs more and original recovery image is saved on the HARD drive. At first he was saved on the second partition of HARD drive and visible for laptop owners. Many people have deleted and do some experiments with these files for recovery. Later after the screwing up of most of them wondered why the recovery installation doesn t work anymore and blaming Toshiba for non-working HARD drive recovery facility.

  You need to just check this forum and see how many comments you can find here all this.

  I think that was the reason why Toshiba has decided to save this image on a hidden partition to avoid such things. Please note that this image of hidden recovery is designed for your laptop only and can be used if your laptop has the factory settings. Any type of change may result with missing option to start the installation of HARD drive recovery.

  Problem is that people don't read the operating manuals and don t understand how it works. To avoid any situation where the installation of the HARD disk can't start or failure HARD disk Toshiba strictly recommended recovery DVD creation. I m wondering really you didn't create these disks.

  At this point, I would like to repeat what I think: you will not be able to do anything, except by using the original installation disc of recovery. To be honest, it is cheap and costs 30 euros. Don t waste your time to play, buy, install the OS, and be happy.

  Bye and good luck