Why my key USB 3 is not correctly recognized

Similar Questions

• GPIB-USB-HS is not correctly recognized NI Max and impossible to find NI VISA resources

  Hello

  I use a laptop Lenovo T400 with Windows XP SP3 and NEITHER 488.2 14.0 installed top. I plugged the laptop GPIB-USB-HS. It can be found in Device Manager normally but may not be properly recognized OR max. In addition, it is not found in resource NI VISA either. Please see attached picture. I reinstalled OR 488.2 and NI VISA. The problem is still there. Advice please? Thank you very much.

  Sincerely,

  James

  OR GPIB enumeration Service is not started. The problem disappeared after the service started. Thank you.

  rqg0717 wrote:

  Hello

  I use a laptop Lenovo T400 with Windows XP SP3 and NEITHER 488.2 14.0 installed top. I plugged the laptop GPIB-USB-HS. It can be found in Device Manager normally but may not be properly recognized OR max. In addition, it is not found in resource NI VISA either. Please see attached picture. I reinstalled OR 488.2 and NI VISA. The problem is still there. Advice please? Thank you very much.

  Sincerely,

  James

• How to fix my usb ports? Not correctly recognize the iPod and other devices of storage correctly.

  I had problems with getting my iPod classic 6th generation to be recognized by my computer windows 7.  It works very well but all of a sudden stopped working.  When I connect the iPod, it says on the product than its 'connected' and is in charge, but does not appear on "my computer" or on iTunes.  Now, I supposed that it was a problem with my apple product, but after putting in the store and plug both Mac and PCs, this worked fine, its clear that it is actually a problem with my specific PC.
  All software are up to date and I tried stop and start the unit. (Control Panel > administrative tools > services > device mobile apple).  The PC also recognizes the iPod randomly once in a while and I managed to restore the iPod to factory settings to ensure that there is no problem with the device itself.

  As stated earlier that the iPod is not visible in 'my computer', but when "devices and printers", there are two elements relating to the iPod, appearing almost as if it's two separate devices. the first is "apple ipod usb device" on the devices section and "Apple mobile device USB driver" in the section not specified.  When I click the first device it freezes the computer for awhile.
  I tried to move the ipod to different USB ports that make no difference.  However, when I put in a pen memory USB (TDK 4 GB), it initially also put it in unspecified, but with a yellow warning down logo on the left and when I moved my wireless usb key for my keyboard, it didn't work initially.  These two seem to have resolved themselves in Device Manager...

  In my view, there is a problem with my usb ports grateful drivers. Any idea what I need to do?

  Hello

  Thanks to community Microsoft can help you with your concern for Windows!

  You are facing problems with the USB ports on the computer.

  Method 1:

  Run the troubleshooter of material and check what is happening.

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Method 2:

  As all devices have same also have USB device associated drivers. Appropriate sometimes drivers not detected after initial installation so reinstalling the drivers can fix the problems.

  You can check after uninstalling and reinstalling USB drivers if you are able to connect. You can disconnect all USB devices and then perform the following steps:

  1. click on start and then click Control Panel.

  2. click on system and Maintenance, click System, and then click Device Manager.

  Note: If Control Panel is in Classic view, double-click System and then click on Device Manager.

  If you are prompted for an administrator password or a confirmation, type the password, or click on allow.

  3. in Device Manager, double-click to expand the "USB Bus controllers", right click on the controller host, click "Uninstall" and click "OK".

  Check that if at all, there is an exclamation point on the pilot, it suggests problems with the installed driver.

  4. Repeat step 2 to uninstall all items under 'USB Bus controllers'.

  Then, restart your computer and Windows 7 will automatically reinstall all USB controllers.

  Method 3:

  You can update the driver from chipset from the web site of the manufacturer and then uninstall and reinstall the device driver updated from the web site of the manufacturer.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  If the problem persists, or you need help on Windows please keep us informed.

  We will be happy to help you!

• Wireless USB adapter is not correctly detected by XP

  Hello, I have Windows XP SP3 computer in office. I also have a Cisco AE2500 wireless adapter. When I conect the adapter it detects but I go to the Device Manager and it shows as 'unknown' and with a yellow exclamation point. Most of you would say update the drivers, but I already have and they are drivers xp and ive tried uninstalling and reinstalling and it still does not work, please help if you can and thank you!

  I also try with n-300 net gear

  They both work because I tried on other xp computers

  [IMG] http://i41.tinypic.com/2pyst1f.jpg [line]
  http://I41.Tinypic.com/2pyst1f.jpg < view="" snapshot="">

  Hello

  ·         Did you try to plug the device into the other USB port and check if it works?

  ·         Another USB device works fine on the computer?

  Follow these methods and check if it works:

  Method 1:

  Follow the form of measures troubleshooting article and check if that helps.

   

  Why my computer does not detect my new USB device when I run Windows XP or Windows Server 2003?

  http://support.Microsoft.com/kb/314634

  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 how to back up and restore the registry in Windows

  Method 2:

  I also suggest you to follow the steps in this Microsoft KB article troubleshooting and check if that helps.

  Advanced troubleshooting tips for General USB for Windows XP problems

  http://support.Microsoft.com/kb/310575

  Method 3:

  The main reason for an unknown device to display in your device manager is because you have a device that is not working properly. To resolve this problem, obtain an updated driver for the device. For more information, see this article:

   

  How to troubleshoot unknown devices listed in Device Manager in Windows XP

  http://support.Microsoft.com/kb/314464

• Satellite A500-1GL - some FN keys only work does not correctly

  Hello
  I have the Toshiba Satellite A500-1GL, and I have a problem with the FN key (actually not the key itself, is the other keys, the keys that have orders)
  for example:
  FN + ESC = mute, and it works great!
  But... FN + F8, should turn the wireless, but it's not!
  Here is a list of what work is / is not:

  FN + ESC: Mute {color: #008000} (Working) {color}
  FN + F1: Lock/unlock windows {color: #008000} (Working) {color}
  FN + F2: Search {color: #ff0000}(Not Working) {color}
  FN + F3: Sleep {color: #008000} (Working) {color}
  FN + F4: Hibernate {color: #ff0000} (doesn't) {color}
  FN + F5: Screen output Monitonr/projector {color: #008000} (Workin) {color}
  FN + F6: Decrease brightness {color: #ff0000}(Not Working) {color} it really increases the light!
  FN + F7: Increase brightness {color: #ff0000}(Not Working) {color} it decreases! O_O
  FN + F8: Turn the wireless on / off {color: #ff0000}(Not Working) {color}
  FN + F9: Toggle the Touchpad {color: #ff0000}(Not working) {color}
  FN + space: focus {color: #ff0000}(Not Working) {color}

  I tried to use the Toshiba Service Station to check for the update, but I couldn't find!

  I'd appreciate any help.
  Thanks in advance.

  See you soon

  Hello

  You need to reinstall the Toshiba Flash Cards Support utility and added value package!

  First remove the two pieces of the system software.
  Restart the device and then first install the PPV then Toshiba Flash Cards.

  Welcome them

• Why our brother USB printer does not work?

  We tried for several days to get our brother USB Printer to work!  It is a USB Brother printer, model # MFC - 885CW if this will help any! If anyone knows how to get this printer to work, please let us know!  Sincerely, your friends at Iowa City, Iowa - Connie and Bob Richards.

  Have you contacted Brother support?

  What is doing?

  It will not install?

  Do you get any error messages?

  Please provide a few details.

• Shift key works still does not correctly

  I mentioned this problem a couple of days.  I say that it is the SHIFT key, but maybe it's down option.

  Anyway, by the training film, that I use, when I'm on TRANSFORM and hold SHIFT + OPT, the proportions of the image must be limited.  However, they are not.  What I get is the magnifying glass + / icon, which seems to take everything in and out, or, if I move the object transform, only that I'm not limited.

  In addition, I take is more screen screenshots.  When I type the command-shift, I get instead a Spotlight search dialog box before I can hit 4 or if I hit 4 and then control-shift, I get nothing.

  I tried to restore the keyboard preferences and using another keyboard - same thing.  This happened only after I rebooted Photoshop to solve other problems, which might be a lesson and himself.

  See the photos below.

  Thank you very much.

  Kenneth

  

  If uou use photoshop Cc 2015.x

  Go to edit-> preferences-> General

  Click Preferences to reset on quit

  Restart phtoshop

• Win7: Administrator is not correctly recognized

  Hi people

  I have a little problem with my Windows 7 Professional. The starting point for this were two questions:

  (1) I could not create new users, as the correct files and registryentries have not been created.

  (2) using the my separate administrator account (that I don't use usually) I can't change my preferences for Windows Update. It does work with the admin hidden either. I get information that "some preferences are only to be changed by administrators.

  The first problem I could solve actually give everyone more rights for users / default. Not the best solution, but I guess I can live with that.

  The second problem that I couldn't yet solve. I activated the hidden administrator, but still had no permission to modify preferences. If I type mmc at the command line I get an empty window now (actually got a window not empty when the hidden administrator was not activated yet, so I'm a little worried about it). The ProfileList in Windows NT folder in the registry has an entry for each user, so it seems that things were good there. Running Sfc/scannow does not return anything. Although I can't change preferences for Windows Update I always seem to be able to install programs and set other preferences using the hidden admin or my own admin user. I don't really know why this happened, but of course, I would be happy if someone could give me a clue as to how to solve this problem.

  see you soon

  S4nya

  Hello

  I suggest you use the construction in the administrator to create a new administrator account and check if everything works correctly in the account.

  The built-in administrator is not to work from, but to help create another account. Built-in Administrator account should not be used as a normal administrator account, it is not recommended as not all things or options will work from there.

• Imaging Source DFG/SV1 acquisition card is not correctly recognized in LabVIEW 2009

  I have an Imaging Source DFG/SV1 frame grabber/capture card (I think that this example uses a Bt878 chip) that I am using with LabVIEW 2009 (Fall edition 2009 academic Site license), including elements of acquisition of vision (NEITHER Vision, NOR-IMAQ (4.3) OR-IMAQdx (3.4), etc.). I have all the latest sources of imagery support drivers and software for the Board of Directors (http://www.theimagingsource.com/en_US/products/grabbers/dfgsv1/ drivers: v6.0.3.0, IC Software v2.1 and IC Imaging Control v3.1) with drivers being compatible DirectShow. The DFG/SV1 is detected in MAX under devices NOR-MAQdx / DFG/SV1 / cam0 and I can grab and preview images, however to 320 x 240 resolution, I have a higher resolution camera and know that the jury is capable of greater resolution using IC software manufacturing and also via TWAIN with ImageJ software drivers. Interesteingly, if I try to acquire an image of the card purchase using the Vision Assistant, the DFG/SV1 card is not recognized as a card acquisition, but listed under IEEE 1394 or GigE peripheral, revealing with it being direct device that I can't understand. Despite this I can acquire images, but I am limited to 320 x 240 format and change the type of image (RGB, UYVY etc) causes an error. Once again, oddly enough, I can use "enter and select mode example VI" which should only be compatible with IEEE 1394 cameras.

  I'm not sure why LabVIEW is not seen this card properly, I contacted Imaging source who were also intrigued by the fact.

  Any information on how this could be resolved would be much appreciated.

  Thanks in advance.

  Hi OCastell,

  With this Council Imaging Source, the only interface supported with drivers of NI Vision Acquisition is through using IMAQdx DirectShow interface. It is possible that their DirectShow driver does not properly support all of the capabilities of their Council. Given that ICR software and TWAIN support can be routed to a different implementation of one of the DirectShow support, you can see the different features available. Unfortunately, you probably go through Imaging Source to determine why their DirectShow driver does not support the full resolution. You can confirm that it isn't IMAQdx this limiting trying other software such as Windows NetMeeting or AMCAP DirectShow and see what capture resolutions are listed.

  Because the DirectShow interface is managed by IMAQdx driver, it will not be detected as a framegrabber IMAQ using the IMAQ driver. This is expected since it fits in the same category as firewire and GigE Vision cameras and is supported with the IMAQdx driver instead.

  The "Grab and select the Mode" example VI isn't really specific FireWire, although he was certainly intended to highlight the various video modes that generally expose FireWire cameras. Since the DirectShow devices are similar and have several selectable video modes, it's why he's probably working. In any case, IMAQdx abstracts usually differences between all supported camera types and in general a single VI can run on all cameras IMAQdx-taking in charge unless you rely on buses or the camera-specific features.

  Regarding Vision Assistant marking the camera as 'IEEE 1394 or GigE', I think it's just an aesthetic issue (which may already be fixed in new versions). When IMAQdx was out, these are the supported types of cameras and so Vision Assistant was trying to say clearly what driver was used for the type of device. Now that IMAQdx supports a multitude of new interfaces (including DirectShow and some IP cameras) that the label is inaccurate.

  Finally, looking at the specs for this capture card, it looks like a standard reference BT878/848 model and then you could try potentially replace your Imaging Source driver with one here:

  http://BTWinCap.sourceforge.NET/

  I used this with a with IMAQdx BT878 capture card and can get it to capture an image full resolution (but of course, your results may vary...). It goes without saying that this solution using DirectShow is much more limited than using an industrial camera on 1394/firewire or a framegrabber IMAQ.

  Hope this helps,

  Eric

• USB Flash will not be recognized in Windows 10

  I have 1 UltraFit 64 GB, bought last month. It's work very well and smoothly until a few days ago.

  Suddenly, the disc not recognized in my windows laptop 10. I see it in the Disk Manager, but I can't assign a letter, cannot format or do something else.

  I tried 3 other laptops with Windows 10. just noluck

  I tried 2 other laptops with windows7, it should work normally

  I tried on my NAS MyCloud, there work.

  I've created boot on my friend laptop (windows7) then try to start my computer laptop. it's working normally.

  So I think that my USB flash only have problems with Windows 10

  The Bank refused to help me, because they all use windows7 and have no problem with my usb drive.

  You guys can suggest me how to solve this problem?

  Thank you very much.

  You run the last update to win 10 AU? There are jobs everywhere in the Internet of devices USB not recognised in WIn 10 but from what I can find, it seems, the issue has been resolved in the latest version of win 10 to THE.

• Cam sex is not correctly recognized on Satellite L500D

  Hello

  I have a Satellite L500D when I failed to connect in the web cam app appears and say web camera initialization. Please check your device and restart the application or computer.
  I press ok and the application closes down so I checked the Device Manager and there is no camera device.
  I downloaded the driver twice and that you don't always see the driver in the Device Manager box.

  Hello

  That s quite strange.
  What is your laptop pre-installed with original Toshiba (factory State) recovery image?

  Everything is possible and it can be faulty cam but the best way to find out is to install the OS using Toshiba HDD recovery facility. After doing this, you will have to new factory condition.
  With the factory settings, each hardware component should work fine.

  Do not install any additional software. After finishing OS installation webcam control functionality to see if the same thing happens again. If there is the same situation contact the closest service Toshiba and explain the situation.

• DELL new 1 TB drive 6 GB/s SATA is not correctly recognized by DELL SAS 6/ir controller

  I have a Dell PowerEdge R310 with a Raid SAS 6iR controller
  with a SATA 2 x 1 TB drives RAID1 volume.
  The SAS Raid Controller is a LSI1068E chipset.
  Now, I bought a new drive to replace a faulty in the RAID1 volume.
  Has bought the drive with Dell
  400-18614 1 TB SATA 7.2 k 3.5 "HD Hot Plug fully assembled - Kit
  It seems that it is a seagate ST1000NM0033.
  It is a 6GB SATA drive.
  When I replaced the defective drive - the RAID1 game not resync No.
  In fact, the controller has not see the drive. When I plugged the drive
  in another (new), the Bay, and then the controller did see the drive, however,
  it it detected as a virtual disk with only 3950 MB (4 GB)!
  Any idea if this disc is:
  -broken?
  -not compatible with / 3GB SATA?
  -needs jumpers positioned to be compatible?

  Thanks in advance!

  Hi all

  Thanks for the comments.

  However, in my opinion, the disc should work and I shouldn't waste my time at low level

  kind of things. It should be "swap-out/swap-in/resync '...

  So I called the support technique dell that the disc is not good.

  Come back my money - ordered a new one - exactly the same model - and it works very well!

  If the disc was just DOA.

  Thank you all for your time tho.

  Kind regards

  Kurt

• InDesign plugin CS6 not correctly recognized by InDesign

  I tried to create a simple InDesign CS6 plugin that writes to a log file, that I am opening and closing of the InDesign documents. The SDK package had the LinkWatcher example I used as a reference when creating my solution.

  Currently, the problem is that I'm a "Adobe InDesign does not recognize mfindesign.pln as a plug-in" when I try to start InDesign CS6 with the plugin. Is not too useful because it won't let me know where is the problem and the compilation of the code with VS2010 gives me no errors currently.

  Relevant parts of the code for https://github.com/crnd/MFIndesign/can be found. I have been using CResponder as a base class in my implementation.

  Someone at - it good indications where & how to start looking for the problem? Or even better if someone can already identify the mistakes that I made.

  I guess it's the problem of related resources. Check if you have the directory (MFIndesign resources) in the plugins directory

  Concerning

  Bartek

• BlackBerry smartphones HELP! Ball control and keys doesn't work does not correctly!

  I have the curve 8330 and when I put in my unlock code and press the trackball, it acts as if im entering additional keys. When I finally get into the phone and try to press on the trackball, in its action, as if I am pressing the asterisk key. It does not correctly read the keys and is to register them as another key! Help pleaaase!

  This looks like what I've seen several times on a device with moisture damage.

  Even sitting on a countertop bath during a hot steamy shower or bath can cause problems with keyboard and trackball up to this JUST-withered.

  Really, it is more common than you think.

  1 the battery immediately! Do not turn on your BlackBerry device.

  2. allow the device to dry in a warm, dry place for 3 to 5 days * (see below)

  3. DO NOT "check it every day" by placing the battery in. Leave what would to dry completely. It takes time. Replacing the battery to check it can damage only (humidity + power = disaster).

  3. If the unit is hot after the drying period, let it cool to room temperature before placing the battery in the.

  * Suggestions on your BlackBerry in a warm dry place (open, with battery):

  • Place the BB in a container of dry uncooked rice, and then you can also place it in one of the locations mentioned below.
  • On top of all heat dry emitting electronic components: TV or CRT, LCD, TV cable box / Satellite or plasma monitor
  • On the dashboard of your car on a day sunny

• USB keyboard does not work laptop computer whis Satellite A100-012

  I have install WinXPpro and my usb keyboard does not (id error 10). I have try 3 different usb keyboard. Other usb devices are working normally.
  Windows XP Home Edition reanimation keyboard drive works normally.
  I have install the chipset and latest bios drivers. What can I do to make my keyboard work in WinXPpro?

  Hello

  Don t know why the USB keyboard may not be recognized, but I recommend suite solution:

  1. click on start
  2. right click on my computer, click Properties
  3. click on the Hardware tab
  4. click on the Device Manager button.
  5 expand the Universal Serial Bus controllers section.
  6 right-click every device under the Bus USB controllers and click on uninstall to remove them one at a time.
  8 restart the computer and let the operating system reinstall the USB controllers.
  9. plug the removable USB storage device and perform a test to ensure that the problem should be solved.

  good luck buddy