InDesign plugin CS6 not correctly recognized by InDesign

Similar Questions

• Why my key USB 3 is not correctly recognized

  I have a Kingston USB 3 six-month-old stick memory (which works without weird messages on my PC). From time to time (not always) when I plug it into one of the four ports USB 3 on my seven-month-old Dell Inspiron 17R IS tells me that it would work faster in a 3 USB port! Once told me ready boost would not work if I did not USB 2 or better! These messages are trash.

  Dell, at HIS own expense, being a decent company, took the laptop, updated all the drivers and got rid of some echoes of startup. Next, the message appeared again. The next day, told me the ready thing kick boost (see above) and that the next day (yesterday) and today, insertion of the memory stick has produced no message.
  Kingston, another good company, proposed to replace the stick without fees.
  But EVERYONE seems convinced it's a Windows problem (and Microsoft does not correct problems JIB, it?)
  What is going on? And how to stop these absurd messages that appear again?
  Any suggestions? Please?

  Have you tried a different brand of USB 3.0 memory sticks?

  If they do not work correctly then I would offer of replacement of Kingston. If the other brand is not working properly I would make sure to run all windows updates. If it still fails, you will need to contact Dell and look into getting a replacement of the system board.

• GPIB-USB-HS is not correctly recognized NI Max and impossible to find NI VISA resources

  Hello

  I use a laptop Lenovo T400 with Windows XP SP3 and NEITHER 488.2 14.0 installed top. I plugged the laptop GPIB-USB-HS. It can be found in Device Manager normally but may not be properly recognized OR max. In addition, it is not found in resource NI VISA either. Please see attached picture. I reinstalled OR 488.2 and NI VISA. The problem is still there. Advice please? Thank you very much.

  Sincerely,

  James

  OR GPIB enumeration Service is not started. The problem disappeared after the service started. Thank you.

  rqg0717 wrote:

  Hello

  I use a laptop Lenovo T400 with Windows XP SP3 and NEITHER 488.2 14.0 installed top. I plugged the laptop GPIB-USB-HS. It can be found in Device Manager normally but may not be properly recognized OR max. In addition, it is not found in resource NI VISA either. Please see attached picture. I reinstalled OR 488.2 and NI VISA. The problem is still there. Advice please? Thank you very much.

  Sincerely,

  James

• Imaging Source DFG/SV1 acquisition card is not correctly recognized in LabVIEW 2009

  I have an Imaging Source DFG/SV1 frame grabber/capture card (I think that this example uses a Bt878 chip) that I am using with LabVIEW 2009 (Fall edition 2009 academic Site license), including elements of acquisition of vision (NEITHER Vision, NOR-IMAQ (4.3) OR-IMAQdx (3.4), etc.). I have all the latest sources of imagery support drivers and software for the Board of Directors (http://www.theimagingsource.com/en_US/products/grabbers/dfgsv1/ drivers: v6.0.3.0, IC Software v2.1 and IC Imaging Control v3.1) with drivers being compatible DirectShow. The DFG/SV1 is detected in MAX under devices NOR-MAQdx / DFG/SV1 / cam0 and I can grab and preview images, however to 320 x 240 resolution, I have a higher resolution camera and know that the jury is capable of greater resolution using IC software manufacturing and also via TWAIN with ImageJ software drivers. Interesteingly, if I try to acquire an image of the card purchase using the Vision Assistant, the DFG/SV1 card is not recognized as a card acquisition, but listed under IEEE 1394 or GigE peripheral, revealing with it being direct device that I can't understand. Despite this I can acquire images, but I am limited to 320 x 240 format and change the type of image (RGB, UYVY etc) causes an error. Once again, oddly enough, I can use "enter and select mode example VI" which should only be compatible with IEEE 1394 cameras.

  I'm not sure why LabVIEW is not seen this card properly, I contacted Imaging source who were also intrigued by the fact.

  Any information on how this could be resolved would be much appreciated.

  Thanks in advance.

  Hi OCastell,

  With this Council Imaging Source, the only interface supported with drivers of NI Vision Acquisition is through using IMAQdx DirectShow interface. It is possible that their DirectShow driver does not properly support all of the capabilities of their Council. Given that ICR software and TWAIN support can be routed to a different implementation of one of the DirectShow support, you can see the different features available. Unfortunately, you probably go through Imaging Source to determine why their DirectShow driver does not support the full resolution. You can confirm that it isn't IMAQdx this limiting trying other software such as Windows NetMeeting or AMCAP DirectShow and see what capture resolutions are listed.

  Because the DirectShow interface is managed by IMAQdx driver, it will not be detected as a framegrabber IMAQ using the IMAQ driver. This is expected since it fits in the same category as firewire and GigE Vision cameras and is supported with the IMAQdx driver instead.

  The "Grab and select the Mode" example VI isn't really specific FireWire, although he was certainly intended to highlight the various video modes that generally expose FireWire cameras. Since the DirectShow devices are similar and have several selectable video modes, it's why he's probably working. In any case, IMAQdx abstracts usually differences between all supported camera types and in general a single VI can run on all cameras IMAQdx-taking in charge unless you rely on buses or the camera-specific features.

  Regarding Vision Assistant marking the camera as 'IEEE 1394 or GigE', I think it's just an aesthetic issue (which may already be fixed in new versions). When IMAQdx was out, these are the supported types of cameras and so Vision Assistant was trying to say clearly what driver was used for the type of device. Now that IMAQdx supports a multitude of new interfaces (including DirectShow and some IP cameras) that the label is inaccurate.

  Finally, looking at the specs for this capture card, it looks like a standard reference BT878/848 model and then you could try potentially replace your Imaging Source driver with one here:

  http://BTWinCap.sourceforge.NET/

  I used this with a with IMAQdx BT878 capture card and can get it to capture an image full resolution (but of course, your results may vary...). It goes without saying that this solution using DirectShow is much more limited than using an industrial camera on 1394/firewire or a framegrabber IMAQ.

  Hope this helps,

  Eric

• Win7: Administrator is not correctly recognized

  Hi people

  I have a little problem with my Windows 7 Professional. The starting point for this were two questions:

  (1) I could not create new users, as the correct files and registryentries have not been created.

  (2) using the my separate administrator account (that I don't use usually) I can't change my preferences for Windows Update. It does work with the admin hidden either. I get information that "some preferences are only to be changed by administrators.

  The first problem I could solve actually give everyone more rights for users / default. Not the best solution, but I guess I can live with that.

  The second problem that I couldn't yet solve. I activated the hidden administrator, but still had no permission to modify preferences. If I type mmc at the command line I get an empty window now (actually got a window not empty when the hidden administrator was not activated yet, so I'm a little worried about it). The ProfileList in Windows NT folder in the registry has an entry for each user, so it seems that things were good there. Running Sfc/scannow does not return anything. Although I can't change preferences for Windows Update I always seem to be able to install programs and set other preferences using the hidden admin or my own admin user. I don't really know why this happened, but of course, I would be happy if someone could give me a clue as to how to solve this problem.

  see you soon

  S4nya

  Hello

  I suggest you use the construction in the administrator to create a new administrator account and check if everything works correctly in the account.

  The built-in administrator is not to work from, but to help create another account. Built-in Administrator account should not be used as a normal administrator account, it is not recommended as not all things or options will work from there.

• vSAN + health plugin = work not correctly WebClient

  Colleagues, after the installation of plugin vSAN health (VMware-vsan-health - 6.0.1.2940255) WebClient does not work missing from the interface all the shares, off virtual machines are displayed. It is useful only remove plugin et Restart vserver. Any thoughts?

  System: vServer 6.0.0 - 2800571, esxi 6.0.0 - 2809209

  I had the same problem on the Windows version of vCenter.  You must launch a prompt by right clicking and then run as administrator.  Then run Setup from the command prompt.  Right clicking on the file configuration, then on run as administrator does not work.  Thank you, Zach.

• Cam sex is not correctly recognized on Satellite L500D

  Hello

  I have a Satellite L500D when I failed to connect in the web cam app appears and say web camera initialization. Please check your device and restart the application or computer.
  I press ok and the application closes down so I checked the Device Manager and there is no camera device.
  I downloaded the driver twice and that you don't always see the driver in the Device Manager box.

  Hello

  That s quite strange.
  What is your laptop pre-installed with original Toshiba (factory State) recovery image?

  Everything is possible and it can be faulty cam but the best way to find out is to install the OS using Toshiba HDD recovery facility. After doing this, you will have to new factory condition.
  With the factory settings, each hardware component should work fine.

  Do not install any additional software. After finishing OS installation webcam control functionality to see if the same thing happens again. If there is the same situation contact the closest service Toshiba and explain the situation.

• DELL new 1 TB drive 6 GB/s SATA is not correctly recognized by DELL SAS 6/ir controller

  I have a Dell PowerEdge R310 with a Raid SAS 6iR controller
  with a SATA 2 x 1 TB drives RAID1 volume.
  The SAS Raid Controller is a LSI1068E chipset.
  Now, I bought a new drive to replace a faulty in the RAID1 volume.
  Has bought the drive with Dell
  400-18614 1 TB SATA 7.2 k 3.5 "HD Hot Plug fully assembled - Kit
  It seems that it is a seagate ST1000NM0033.
  It is a 6GB SATA drive.
  When I replaced the defective drive - the RAID1 game not resync No.
  In fact, the controller has not see the drive. When I plugged the drive
  in another (new), the Bay, and then the controller did see the drive, however,
  it it detected as a virtual disk with only 3950 MB (4 GB)!
  Any idea if this disc is:
  -broken?
  -not compatible with / 3GB SATA?
  -needs jumpers positioned to be compatible?

  Thanks in advance!

  Hi all

  Thanks for the comments.

  However, in my opinion, the disc should work and I shouldn't waste my time at low level

  kind of things. It should be "swap-out/swap-in/resync '...

  So I called the support technique dell that the disc is not good.

  Come back my money - ordered a new one - exactly the same model - and it works very well!

  If the disc was just DOA.

  Thank you all for your time tho.

  Kind regards

  Kurt

• Why does my indesign cs6 not print black (k100) correctly?

  InDesign does not correctly print black 100%, but at 90% to 1%, prints well?

  

  Thank you all for your support and your help to try to solve this problem, but on a hunch, I looked again the printer cartridges and found that the Black-light cartridge was defective, all prints come out now as it should.

  Thanks a lot again

• CS6 not recognizing plugins

  I installed the plugins for CS6(64bit) in Program Files/Adobe/Adobe Photoshop CS6 (64-bit) / other Plug-ins and nothing!  CS6 does not, namely "dofpro.8bf" and its companion file "convert.exe".  I checked the above path is in the additional plugins CS6 preferences.

  I then copied the Program Files/Adobe/Adobe Photoshop CS6 (64-bit) files / Plug-ins and no help!

  I looked everywhere and can't find any other places to install files.

  Instructions for the DOF Pro software simply copy the two files in the folder where CS6 has its plug-ins.  I don't know why CS6 does not display the DOF Pro filter option in the drop-down filter.

  Any ideas what's happening?

  I am running Windows 7 family 64-bit and it is perfectly up-to-date.

  Thanks for your help!

  Gary Kueppers

  You run the 32-bit application (which has a different plugins folder) by mistake?

  This plugin compatible with 64 bit addressing? (some are not)

  In addition, the "Plug-ins extra" is not a folder of Photoshop.

  Your third-party plugins go into the folder "Plug-Ins".

• CS6 exporter Plugin does not open premiere elements 11 (Windows)

  I want to make my exporter (Windows) - compatible with 11 elements of first plugin.

  So far, I've got my exporter plugin in Adobe Premiere Pro CS6 and Media Encoder CS6 and the plugin it runs correctly.

  I then followed the indications for execution of Premeire CS6 to create an export preset (*.epr) file.  I copied copied this file exported *.epr to 'OTHERS/MyCompany/MyPreset.epr' in my first [App installation folder] 11.  (As well as the copy of the plugin-binary *.prm to Plug-ins/common

  In the tab < Publish: share > when I use the mouse to select 'OTHER', I get an error dialog box:

  "Premiere Elements has encountered an error.

  [..-.. \Src\Exporter_Accessors.cpp-213] "[Continue]

  After I click on continue, I do not get the dialog box to my plugin-exporter.  In the tab < Publish: share >, I now see the triangle warning and text next to it: "export invalid parameters."

  Premiere Elements team notes that first elements 11 is based on the version of MediaCore CS5.5.  So, using the SDK CS5.5 is probably the best way to build plug-ins to specifically target the Prem El 11.

• Movie Convert plugin will not appear on CS6

  Hello

  I recently bought convert movie 2.12 pro to use the first pro cs6.

  It will not appear in my effects Panel although it is in the folder plugins-cs6-common.

  I looked online and shift operation so that I start the Prime Minister to update plug-ins had no luck either.

  Help, please!  I would really like to use it for my work in time.

  Thank you

  Davies101 wrote:

  It will not appear in my effects Panel although it is in the folder plugins-cs6-common.

  I looked online and shift operation so that I start the Prime Minister to update plug-ins had no luck either.

  have you checked this thing? !!!

  http://www.filmconvert.com/help/default.aspx?help_id=37

  (read the NOTE at the bottom... it says hold Shift and Alt keys!)

  If you still cannot operate, your best shot is to communicate with them in New Zealand!

  http://www.filmconvert.com/Contact_us.aspx

  baaa, Tak!

  hahahahahahahahahahahahahahaha!

• Flash does not correctly install in the directory Plugins of Firefox 3. Help!

  Hello
  
  I had a real bear trying to get flash works with firefox 3. For awhile, I've been runing Firefox 2 and Firefox 3 beta/RC side by side (installed in different directories, of course), but now that Firefox 3 is out, I uninstalled Firefox 2 and do a fresh install of Firefox 3. However, when I try to run the Flash Player installer, it lists the "output folder" as "C:\WINDOWS\system32\Macromed\Flash" and does not affect the directory of the Firefox plugin - which of course means that Firefox does not know that the plugin is here.
  
  I don't know if it's the default behavior and some files are copied but not correctly, or if the output folder is simply false, but if I manually copy the contents of the C:\windows\system32\macromed folder in the plugins directory, flash works in Firefox.
  
  I need the installer works well. Can someone help me with this?
  
  Thanks in advance.

  OK, I found the problem: there are incorrect permissions in the registry. The Administrator's guide led me to this page: http://kb.adobe.com/selfservice/viewContent.do?externalId=tn_19148&sliceId=2. I discovered the HKLM/Software/Macromedia registry key (as well as two key in HKLM/Software/Mozilla, Firefox and ' HKLM/Software/Mozilla Plugins') was inaccessible to the administrator; I had to take possession of the key and replace the permissions.

  So the problem (get flash to install correctly) is now fixed. I guess the problem didn't rear its head with older versions of flash, because they have installed the flash plugin in the directory plugins of firefox rather than rely on the registry.

  Thanks for all your help!

• [CS4 Server Win]: Plugin does not work on Windows Server 2003?

  Hello

  can anyone help?

  My plugin works on Windows XP and Windows Vista.

  On the two operating systems, the methods of scripts are visible in ExtendScript Toolkit and can be called by javascript.

  On Windows Server 2003 that my plugin is not running, the script methods are not visible in ExtendScript Toolkit!

  What is missing?

  Thank you

  Alois Blaimer

  Looks like you are using a compiler more later-than-recommended that refers to a later-than-recommended runtime library that is not included in the OS and/or InDesign.

  Either:

  1. Use the correct compiler
  2. Discover the missing library and install it
  3. twist the compiler to use the correct library

  (I would recommend against 2) and 3) because these hacks tend to break.

  For example if you delete something through your runtime lib that has been allocated by InDesign through competitors runtime lib, you could screw up memory management.

  Dirk

• "images are not a recognized format" boredom

  a previous post - 2013 - illuminated the problem.

  I'm having issues importing still images in a sequence of time in photoshop and would appreciate suggestions!

  I want to create a time using a sequence of photographs.  All file names are in name order / numbered.

  I use the workspace of proposal and followed all the instructions available.

  • Create correct size document (film and video).
  • Create a video montage.
  • Pace of game.
  • Choose 'create new video layer from file '.
  • Point to the first image in the folder where the pictures are stored.

  At this point, no matter what I tried, I get this error:

  

  end of the previous post.

  I have the same problem and it is extremely frustrating because I have to export via LR6 thousands of images as tif files in a different folder, because; file, new layer of the file (in ch cc) does NOT RECOGNIZE on my photoshop jpeg files.

  He acknowledges that tif files?

  I tried stuarts how to use file, layer, new layer of the file instead, and although it seems to work it doesn't matter all files? When I try and export the video, the work area is stuck at 0-59

  and Yes, all my images are renamed and numbered sequentially.

  I don't understand what setting may need to be changed to allow it to load all images. can there be something in the preferences which addressed this?

  My ps cc created vids mp4 perfectly to the exported JPEGs LR, tiff (in thousands at the time) files but does not load JPEG files, I get this msg:

  "Unable to complete the new video layer from file because the film is not a recognized format"

  Thanks for any help with this annoyance "footage is an unrecognized format.

  TWS

  Have you seen Julianne Kost on Lynda.com tutorial?  I think it's free show without subscription Lynda.

  Photoshop CC Essential Training (2015)

  If this does not give you the answer, come back and I'm sure someone here can give you more specific advice.

  [EDIT]  I just saw the other thread that you hit.  As you say, that is three years old, and things are different with new versions of Photoshop, so the question is, which version do you use?  If you have a version of CS6 pre, then maybe something like Quicktime Pro could be better.  You mentioned the proposal workspace, so I think that you have the latest version, in which case that old thread is probably more relevant.