Windows 7 does not recognize the Patriot 256 GB Flash Drive

Similar Questions

• Satellite A200-1AE does not recognize the USB 2.0 flash drive

  I have a problem because my satellite A200-1AE with Microsoft Vista does not recognize the USB 2.0 flash drive. He asks me a program/software!
  The same USB works without problem on other computers with vista!

  Someone knows what to do?

  Hello

  First of all, you must disconnect all USB devices and must remove the USB ports and controllers in the Device Manager.
  After this procedure, you must restart the laptop. After a new restart the Vista operating system should recognize the USB ports and should reinstall USB drivers again.

  Then you must update the Vista to the State! All fixes and patches must be installed. Please note that you will have to visit the MS Update site for all patches

  Notes; MS has released a beta of Vista SP1. I installed it on my laptop and it has solved several problems.

  Best regards

• Windows 7 does not recognize the new WD external hard drive added to the usb port

  Recently, I tried to add my third USB WD hard drive to my computer.  It's a My Book Essential.  The meter turns and the virtual cd drive is listed in WD, but the hard drive itself does not appear on the list of devices with a drive letter.  My my first two books are readers: J:, and L: I have no "new device found" message   I search for new devices and it the PC do not find anything.  If I click on the virtual CD drive (M :) it askes if I want the computer to allow WD to make changes...) I say Yes and the screen flashes and nothing happens.
  The drive be defective?  Any other ideas?

  Hello

  Have you tried to connect the external hard drive on another USB port?

  Try to connect the WD external hard drive on another computer.

  Follow these steps:

  Method 1: You can run the troubleshooter in the following article and see if this fits the Bill.

  Open the hardware and devices Troubleshooter

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Also, run the Fixit.
  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

  Method 2: Check if the external hard drive is recognized in disk management and assign a drive letter to the same.

  To open disk management, follow these steps:

  a. click Start, type disk management in the start search box and press enter.

  (b) if the drive is detected in disk management, I suggest you to assign a drive letter and see if that does the trick.

  For instructions, see this article change, add, or remove a drive letter

• LG C500-G. AEE5GE1 with Windows 7 home prem OA MEA have been formatted. But despite giving the product key and Windows registry does not recognize the activation. Help, please

  LG C500-G. AEE5GE1 with Windows 7 home prem OA MEA have been formatted. But despite giving the product key and Windows registry does not recognize the activation. Help, please

  Name of the operating system Microsoft Windows 7 Home Premium

  Version 6.1.7601 Service Pack 1 Build 7601

  Manufacturer of operating system Microsoft Corporation

  System name HANDSOME-PC

  System manufacturer LG Electronics

  System model C500.-g. AEE5GE1

  System Type X 86-based PC

  Processor Intel (r) Core i3 CPU M 390 @ 2.67 GHz, 2666 Mhz, 2 Lossnay, 4 logical processors

  H46YSF00 Version/Date of BIOS American Megatrends Inc., July 2, 10

  Product key:

  X 16-96084

  CONCERNING

  TUESDAY BIOJY

  Have you tried to restart by phone?

  How to activate Windows 7 manually (activate by phone)
   
  1) click Start and in the search for box type: slui.exe 4
   
  (2) press the ENTER"" key.
   
  (3) select your "country" in the list.
   
  (4) choose the option "activate phone".
   
  (5) stay on the phone (do not select/press all options) and wait for a person to help you with the activation.
   
  (6) explain your problem clearly to the support person.
   
  http://support.Microsoft.com/kb/950929/en-us

• Install Windows 8 does not recognize the system drive

  I built a new machine (chart below). Since this is a new machine and not an upgrade, I bought Win 8 Pro 64 bit OEM to do a clean install. The SSD is my system disk that Windows 8 will be installed. Four data drives are mirrored, two for the other two. Construction went perfectly. The BIOS recognizes all six disks: 1 SSD, 4 HDD, 1 DVD.

  Insert and boot the disk of Windows 8. Accept the EULA, enter the product key. Arriving at the page "Where do you want to install Windows?", only four hard disks are listed. The SSD (installation to go) is not found by Win 8. ??? I tried to change ports SATA, cables, power supply - no difference. For each new change of hardware, the BIOS still sees everything. This isn't a hardware problem.

  The question remains: why the installation of Windows 8 does not recognize the SSD drive. All five disks are on AHCI. I'm not in RAID.

  I spoke with crucial technical support of all (manufacturer of the SSD). They were also surprised that the drive does not appear in the list.

  Does anyone have a solution? I spent all the money on hardware, as well as the new version of Windows and I cannot install it.

  This is the real kick in the teeth: Microsoft won't support me. The OEM of Windows 8 version is the same as manufacturers, such as Dell or HP. Support told me I had the support of the manufacturer. HA! I am the manufacturer. Either that or upgrade from an earlier version of Windows. This means that any that a new construction machine will get ZERO assumption of Microsoft. All just great.

  Thank you in advance for any assistance.

  Windows 8 Pro 64-bit (full version) - OEM
  Intel Core i5 - 3570K
  Card mother GIGABYTE GA-Z77X-UD5H
  Crucial Ballistix 2 x 8 GB DDR3 1600
  Crucial M4 2.5 "128 GB SSD (system disk)
  WD Green WD30EZRX x 4 (data readers) 3 TB drive
  Rosewill Challenger-U3 ATX Mid Tower Case
  SeaSonic M12II 620W 620 Bronze PSU
  ASUS DVD writer

  The DSS must be LOW LEVEL FORMATE.

  Once, there may be no other [HDDs] not connected to the SATA ports.

  Install Windows 8 Pro now.

  [Edit] Can someone please mark this as answered? I can't because I posted the question. Thank you.

• Windows 8 does not support the prolific usb to serial driver

  Windows 8 does not support the prolific usb to serial driver
  What is the solution?
  We want to use windows 8, but because of this driver issue, we do not buy windows 8

  Windows 8 does not support the prolific usb to serial driver
  What is the solution?
  We want to use windows 8, but because of this driver issue, we do not buy windows 8

  Understand when the manufacturer of the hardware device will provide you with the drivers for the hardware you want to use on the operating system you want to use.  If they aren't - so there you go.

• Qosmio F30 - 112 - Windows XP does not recognize the HARD drive

  Hello.

  I have a Qosmio F30-112.
  I tried to install the Windows XP Professional instead of the Media Center edition.
  However, during the execution of the installer, my laptop does not recognize the hard drive. Therefore, the installation cannot continue.

  I thought it might be a problem of corruption with my laptop and reinstalled Media Center Edition successfully.
  But when I try to install XP Professional it always gives me the same error.

  Suggestions for the configuration of the BIOS or solutions for why this is happening?

  Thanks in advance.

  Hello

  Just a question:
  You are looking for in this forum for other similar issues with regard to the installation of Win XP and lack HARD drive? I doubt

  The fact is that your notebook has a SATA controller and you need a SATA (Intel Matrix Storage Manager) driver.

  You should have a look here in this doc from Toshiba:
  [How to integrate a SATA AHCI driver into a Windows XP installation CD | http://aps2.toshiba-tro.de/kb0/TSB85017Z0000R01.htm]

  and should also search this forum for other threads

  Good bye

• Windows 7 does not recognize the installation discs

  Hello

  I have a problem, and I don't know if there is a solution, but here goes.

  My laptop is a HP DV6-7029WM Windows 7, 64 bit.

  The hard drive was dead, and he was replaced last month.  I sent it to HP.  C is the hard drive, and was originally the recovery on D. Removable media were on E, and when I connected a USB stick or memory card reader it would on F.

  When I came back, hard drive was on C as it was originally, and there was no recovery drive D. D is now my removable media drive. When I put in a USB stick or a memory card reader, which is now on the E drive.

  After I bought this, I put the recovery on a USB key, but I've accidentally thrown out. (My mistake) So I ordered the installation diskettes after that I return my HP PC.  I had 2 DVD system recovery disks and an Application and a recovery DVD Drivery.

  I want to reinstall Windows back to the default settings. I put disc 1 (System Recovery DVD) and close.  I reboot and it goes directly to the office. I hear the whirring disc, but nothing happens.

  I go to the control panel > Recovery > advanced retrieval methods. I click on restart, and it loads files and then says DVD set, which I do. He told me that he does not recognize the installation disc.

  I googled this problem and found a poster on CNET that had the same problem as I do. Also, I can't do a system restore.  My problem is the same as this poster on CNET.  I can read DVDs and CDs.  Those that work very well.

  http://forums.CNET.com/7723-19411_102-568059/Windows-7-installation-disc-not-recognized/

  The files are on the DVD, because I see them.

  I don't know what to do. Should I send my PC back? Can I do to solve this problem?

  Thanks in advance.

  pen

  Hello:

  With recovery disc 1 into the DVD drive, restart the computer and at the beginning of the HP welcome screen, press the ESC key to display a menu of options.

  Select the F9 boot menu option.

  Select the DVD drive on the list of bootable devices, and press the Enter key.

  Watch the screen for additional instructions.

• Windows xp does not recognize the hp c6180 photosmart printer

  My windows xp does not recognize my hp c6180 photosmart printer

  Hello

  1. were you able to use the same printer without any problems before?
  2. don't you make changes on the computer before this problem?
  3. you receive an error message?

  See the following articles that may help you resolve this problem.
  Printer in Windows problems
  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Resources for the resolution of the printer in Windows XP problems
  http://support.Microsoft.com/kb/308028

• Windows XP does not recognize the Sony Walkman NWZ-E344 media player Red

  original title: Sony Walkman NWZ-E344 Media Player Red

  My Windows XP does not recognize my Walkman when installed in USB. All other computers do, then only, assumes that I do not have good pilot.

  Hi brumbybrat,

   

  You must install the drivers for the walkman to recognize.

   

  More information is available in the following links:

   

  Is there a CD of installation for the Walkman® player?

   

  How to install manual and the Content Transfer software for the Walkman® player

• Windows 7 does not recognize the graphics cards

  I have been using the same PC for the last six years of the game without any problem, I upgraded to Windows 10 and things went to * a few days after talking to Microsoft Care I was told that with the latest version of Windows 10 updates and other updates my system is no longer compatible with Windows 10 and I did a clean install to Windows 7. now, Windows 7 does not recognize my graphics cards 2 x 'GeForce GTX 480"with SLI configuration.

  In "Device Manager", it shows two units operating as VGA standard with no details etc.

  It install drivers for the 'GeForce GTX 480"because it does not recognize their being there.

  Any ideas or help... Please also stay simple for a non PC Geek

  No problem if nothing else, you've found the system images is now with win-10 days worth being pushed m main $ :)

  It of free and worth to be using,

  http://www.Macrium.com/reflectfree.aspx

• Windows 8 does not recognize the photosmart 5510

  Cannot use my HP Photosmart since the installation of Windows 8. My pc does not recognize the printer.

  Hello

  Please download the following program and run it on your Windows 8 machine:

  http://ftp.HP.com/pub/softlib/software12/COL44840/MP-109033-2/hppiw.exe

  You need the printer on your home network.

  Kind regards.

• WINDOWS 8 DOES NOT RECOGNIZE THE SCANNER OFFICE HP OFFICEJET 4500

  MY WINDOWS 8 DOES NOT RECOGNIZE SCANNER OFFICE OF HP OFFICEJET 4500

  Hello

  1. don't you get any error message when the scanner not detected?

  2. do you insert scanner in another port of the computer or to another computer?

  3. were there any changes (hardware or software) to the computer before the show?

  4. other recognized devices?

  If your computer is having problems with a recently installed device or other hardware, try to use the hardware and peripheral troubleshooting tool to solve the problem. It checks the common issues of interest and ensures that a new device or hardware connected to your computer has been installed correctly.

  Run the hardware and devices Troubleshooter and see if it helps.

  a: press the logo Windows + O to open the search box.
  b: Type Troubleshooting, press on enter.
  c: now click material and its.
  d: now click hardware and devices , and then click Next 

  Answer please if you have any questions.

• Lost in car-Windows xp does not recognize the slave drive

  I do reinstall xp home, no problem when I did the system does not recognize the slave drive I have.  As far as I can tell that it's all hooked up correctly.  When I go into disk management it does not recognize the drive either.  All of the suggestions.

  Hi james.williams,

  1. How is the drive connected to the computer?
  2. What is the number of the brand and model of the player?

  I suggest that you check the jumper settings and make sure that the jumpers are correctly positioned.

  Make sure they are in the two master/slave jumper and not cable select.

• Recovering the Windows system does not recognize the hard drive

  Computer does not recognize the hard drive when booting.  Guard gives me 1782 disk error.  Then try to use the ROM installation thing and throw a disc hard test there is no option to test anywhere.  Computer was working fine this morning and then I stop when I turned it back on it was not properly start.

  I have a zt3000 running xp sp3

  someone please help me, thanks

  Hello

  Please reinsert the drive from the rear panel and check if the device detects the drive hard in case you have the same problem, then the hard drive is bad, you need to replace the hard drive and reinstall the operating system on the unit to return to its operating state.