Windows 7 does not start after the C disk cloning

Similar Questions

• Windows XP does not start after the installation of an SSD.

  Windows XP SP3 and Intel Smart Response Technology

  Recently, I built a new computer and installed Windows XP Pro and Windows 7 Pro in a dual-boot arrangement.  Everything worked very well.  I then installed an SSD in the hopes of using the Intel Smart Response Technology (SRT) to speed things up.

  I shut down the computer, installed the SSD, brought up in Win7 and follow the easy guests in SRT to activate the player.  Restarted several times and things SSD speed up significantly.  Wonderful.
  I so restart and select Windows XP so I can SRT it.  After you select Windows XP in the boot menu, a few seconds and I get a quick flash of a BSOD and the computer restarts spontaneously.  I can't enter in WinXP, not even without failure or last known good config Mode.
  I again in Win7 and disable the SRT, reboot and I can enter Windows XP very well.  So obviously WinXP has a problem with the SRT is activated outside the XP.  That being said, I can't activate SRT in WinXP first either.  "Accelerate" option does not appear in the menu.
  Any ideas on that?
  Thanks for your help!
  -Matt

  Hello

  In these cases, we always recommend to update the system BIOS of motherboard, update the firmware of the controller RAID and disks installed. If the problem persists, you will need to fix the compatibility problem directly with the manufacturer of the motherboard and add it to the RAID controller itself.

  I suggest you to contact Intel support site to improve assistance on the issue.

  http://www.Intel.com/p/en_US/support?IID=HDR+support

  Warning of the BIOS:

  BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  See also:

  http://download.Intel.com/support/chipsets/SB/intel_smart_response_technology_user_guide.PDF

• Windows XP does not start after the installation of 3 GB of RAM. Will start with only 2 GB or less.

  I installed the new RAM on my desktop Compaq EVO D500.  Everything was working fine until 2 GB.  When I tried to install no matter what the computer does not start.  Specifications of the computer say maximum RAM is 3 GB.  All the memory and are good because I swapped taken in all the combinations possible and memory.  Any ideas. gknapp_ny

  If their were any memory related settings that had to be changed I would have no idea how do.  I had initially 512 MB of RAM (256-2 sticks).  I added a stick of 1 GB aditional third availabel taking and all went well.  Then I had two more identical 1 GB sticks and added them one at a time.  With 2 GB without problem.  But with the third stick of 1 GB that I couldn't start - I just beeps. I swapped one of the sticks of 1 GB for an old 256 MB and still no start just beeps.  When I run 2 GB everything is fine.  The BIOS recognizes the 2 GB of RAM. gknapp_ny

  Sounds as if your BIOS will not identify no matter what says the spec, 3 GB.

  It seems as if you may need a BIOS update in order to recognize the 3 GB of RAM - especially if it is a very old Compaq Evo D500.  See the "Improvements" tab to the page linked below.

  See http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=12454&prodSeriesId=96295&swItem=PSG_I15378-37635&prodNameId=97121&swEnvOID=1093&swLang=13&taskId=135&mode=3

  Note that the patch on the link above is for models Evo D500 "with a ROM family 686Y2."  Read the "Release Notes" on this page to determine if your machine is one of those and if so, see "Instructions of Installation" to install the upgrade.  If your D500 is a laptop, you should Flash the ROM ONLY (i.e., update the BIOS level) when the computer is plugged - loss of power during this process can potentially cause irreparable harm to the computer.

• Windows vista does not start try the recovery disk and nothing

  I have a pavilion hp a1712n with windows vista starts not tried the disk recovery and nothing, it sounds like it is stuck in mode 'sleep'. I can hear it loading but it dosnt take the cd/dvd drive, I tried unpluging the drive to see if it will continue to load, but it didn't. I can not use the key to go into bios Board or something, all ideas given lose don't are not important computer been gave me this problem, so if there is something that I can do but personal files will be lost is very well thank you all

  Hi scoobydoochick,

  1. what recovery disc do you have?

  2. you receive an error message?

  3. you see the computer manufacturer's logo while you start the computer?

  Looks like that there are some hardware failure on the computer that is preventing the computer from starting.

  Will need you a Windows vista installation disc as recovery are different from the install disc and restore disks are created by the computer manufacturer, we are not aware of its functions.

  Once you get the Windows vista installation disc, that you try startup repair by using the link below or take the local computer tech shop and the material tested on the computer.

  What to do if Windows does not start correctly

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-to-do-if-Windows-wont-start-correctly

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Pavilion HDX 16: Windows 7 does not start after the upgrade to Windows 10

  Hello

  I have a system to dual-boot with windows 7 and ubuntu (with Windows 7 and NeoGrub Bootloader Windows Boot Manager).

  Recently, I upgraded from windows 7 to windows 10 via free upgrade offered by SM. However, I didn't like windows 10 and tried to upgrade to windows 7 by the following settings-> update of the security & -> Recovery-> Go Back to Windows 7.

  After the long process of decommissioning, cannot start windows 7 and the "Startup Repair" tool began to run. However, he could not solve the problem. Other recovery options 'system restore' and 'image system recovery' is not such that it could not find any restore point or the image created previously (I'm sure it were created before upgrade restore points).

  So, although I can boot ubuntu without any problem, I can't start windows 7. After the "starting windows" screen, I get the blue screen (a problem has been detected and windows has been shut down...).

  I intend to use the DVD to install windows 7 for repair, but

  (1) I don't know if I can boot from the CD because it is a dual-boot configuration

  (2) I'm afraid of losing work ubuntu OS.

  I appreciate if someone can help me find my Windows 7. I thank very you much for your time.

  Sorry, but there are a lot of reports on forums of Win10 the option of GoBack does not always work correctly.

  You should be able to boot properly from the same DVD of Win7 if you dual-boot with Ubuntu, but be aware, if the startup repair works (you may need to run three times), it will replace the link to start Linux in the MBR and after that, the machine starts immediately to Win7.  You will need to reinstall GRUB to get Ubuntu boot back.  You may be able to fix the boot of Ubuntu using repair boot: Boot-Repair - Community Ubuntu Documentation

• Windows 7 does not start after the installation of updates - sounds familiar!

  Apparently, I have another system that no longer starts after you install an update to Windows 7. New kick computer _ I have to disable the automatic update of windows. Twice I had to restore the system in the first week because he hung up after the installation of updates for windows 7. I have no idea what update is the cause of the problem.

  Essentially, start the screen goes black with the cursor blinking in the upper left corner of the screen. The only way out is to restore the system.

  Does anyone know what update is the culpret? HP support has no idea. Their only solution was to update windows 7 to 'never download an update from windows '. It is a terrible thing to be underestimated solution.

  Here's the resolution...

  I installed all the updates except KB2284742 954430, 973688 and 971033. So I decided to install these 1 4 at a time in the order shown. I installed successfully 228472 and 954430 and 973688 disappeared from the list of available updates. So I installed 971033 and it installed successfully and I was still able to restart.

  My conclusion is that there is a conflict between the first 3 updates when they are installed at the same time.

  Now my system is up to date with all windows updates and I'm able to restart without any problems!

  Close this message.

• Windows Vista does not start after the beginning upward

  My computer won't start Windows Vista after startup, I tried startup repair and it gave me a screen type scrambled at the end.  When I let him start normally I get a black screen and when I do the Startup Repair I get every time the same garbled screen. I tried to reinstall Windows Vista, but when I put the disc in my pc it did nothing. How can I reinstall the operating system?

  Hello

  Startup Repair might not have worked however the SFC, CheckDisk system restore and then even a new attempt of
  Startup Repair might work.

  Try the repair to start the Recovery Console (if you have a) or from a disk of Vista - if you have not a
  Disk of Vista, you can borrow a friends (they are not protected against copying) or make a. The manufacturer of your system will also
  sell cheap physical disks since you already own Windows.

  This tells you how to access the System Recovery Options and/or with a Vista disk
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  Try Options recovery or a disk of Vista startup repair.

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  Also from the command PROMPT on the Console (if possible) recovery or a Vista disk

  SFC/scannow
  Press enter

  and after that runs away

  Chkdsk /f /r
  Press enter

  (Spaces between C and / k and / and f and /)

  Retry After Chkdsk startup repair.

  If after those try you system restore from the recovery or Vista disc.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html
  Retry if necessary startup repair.

  =================================================

  To re - install:

  Check with your system manufacturer that they all slightly different methods. They may have included a recovery
  Partition or other methods to restore the default value. Also your system manufacturer will sell you the physical disks at a great price
  Since you already own windows.

  What are the system recovery options in Windows Vista?
  http://windowshelp.Microsoft.com/Windows/en-us/help/2b3724d1-f4ad-5b26-16dc-3e9e66f4be5e1033.mspx

  This tells you how to access the System Recovery Options and/or Vista discs
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  ----------------------------------------------------------------------------------------

  Check with your system manufacturer support as they may have understood, Partitions recovery Vista DVD, and/or
  other methods to return to the original configuration.

  Here it is just a few options and you should contact our service system Maker to be sure
  you know all the options you have.

  How to perform a repair for Vista Installation (this keeps your data if the backup off the)
  Player is safe)
  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

  How to do a clean install and the installer with a full Version of Vista - this erase ALL programs and data on
  http://www.Vistax64.com/tutorials/117366-clean-install-full-version-Vista.html

  This tells you how to access the System Recovery Options and/or Vista disk
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  How to do a clean install with a Version upgrade to Vista - this wipes ALL programs and data on
  http://www.Vistax64.com/tutorials/68767-clean-install-upgrade-Vista.html

  How to do a Custom Installation of Vista - this is a clean install should, however, save your data
  http://www.Vistax64.com/tutorials/241565-custom-install-Vista.html

  Upgrade to another edition of Windows Vista - this should keep the programs and data
  http://windowshelp.Microsoft.com/Windows/en-us/help/3af7e05f-4d2a-4af7-A168-9242f9093bb81033.mspx

  Installation and reinstallation of Windows (upgrade - store programs and data or New Installation that removes them)
  http://windowshelp.Microsoft.com/Windows/en-us/help/e77344fa-e978-464c-953e-eba44f0522671033.mspx

  On-site upgrade
  http://vistasupport.MVPs.org/repair_a_vista_installation_using_the_upgrade_option_of_the_vista_dvd.htm

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Windows xp does not start after the system restore

  Hi, a few days ago, I restored the system to my computer because it showed no hard disks that have been added to the computer. I had no problem before, so I restored the system to the same day. AGTER system restore, my computer would not start. Well, it's not to the point where I'm supposed to pick a user, but instead of a list of users, it shows 'windows xp' on a blue background. I turned the computer off tension and Trier to start in "safe mode", but it did not help. What should I do? Thank you.

  Hello

  Follow these steps and check if they help.

  Step 1:

  Remove all external devices such as printers, USB and then try to start.

  Step 2:

  I suggest that you perform the installation of repair XP on your computer and check if that helps.

  http://www.Microsoft.com/windowsxp/using/helpandsupport/learnmore/tips/doug92.mspx

  Note: Make sure you have uninstalled the latest version of Internet Explorer if installed before to perform the repair facility.

  Reference:

  http://support.Microsoft.com/kb/917964

• 32 bit Windows Vista does not start after the electricity blackout

  Hello
  I was running the computer normally, and unfortunately, a power outage unexpectedly turns off the computer. Usually its not much, just start it as soon as the power is restored, however, this time on restart, it got stuck at the beginning (the screen with the slide bar through the green screen).
  It's the first time that, on an unexpected shutdown that has happened.
  I tried to leave the system operating at the start of the longest screen half an hour, but it seems as if the system was locked in a never-ending loop of the sliding, green bar as if the system can not find something to start upward.

  Hello

  See if that helps you.

  Do a Safe Mode system restore to before the problem started.

  http://bertk.MVPs.org/html/restoresysv.html

  How to access Safe Mode

  http://www.bleepingcomputer.com/tutorials/how-to-start-Windows-in-safe-mode/#Vista

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  If it doesn't, try a startup repair and / or a system restore using a DVD of Vista from Microsoft

  Manufacturers recovery disks normally do not have Service Options; they are normally a relocation to the factory only settings option.

  Here is the guide to repair Options using a Vista DVD from Microsoft.

  If a friend or a work acquantance of yours has one, you can borrow and use it for repairs.

  http://www.bleepingcomputer.com/tutorials/repair-Windows-with-Windows-Startup-Repair/

  Table of contents

  1. Overview of Windows Vista repair options
  2. How to perform an automatic repair of Windows Vista using Startup Repair
  3. Advanced Tools Overview
  4. Conclusion

  If you do not or can not borrow a Microsoft DVD there is a download of a file ISO of Vista Startup Repair available that you can put on a Bootable floppy to make the above startup repair and that the method is recommended by a large number of posters in these Forums.

  Unfortunately, you have to buy it.

  Here is a link to it:

  http://NeoSmart.net/blog/2011/Windows-Recovery-discs-updated-reinstated/

  See you soon.

• Windows Vista does not start after the abnormal termination.

  I use windows Vista Home premium for more
  two years without major problems so far. However, this week, I encountered a major problem with Vista, the computer froze and I had to manually turned off. After that when I rebooted my laptop, it will remain on the screen starting with drag the green bars forever.

  I tried the following:

  
  -start in safe mode: safe mode works, but normal startup after that still hangs.
  -System Restore: System Restore works, but even after restoring hangs normal startup.
  -repair of the system with the help of the installation DVD: is not able to repair.
  reports of undetermined origin.

  Help, please.

  Thanks in advance.

  "Gets to a point where I see microsft operation and green bar and it gets stuck.
  there forever. "
   
  Hmmm - it's therefore something quite critical, then! :(
   
  Start safe mode and run the System File Checker
   
  1) click the Start button
  (2) type: cmd.exe
  (3) right click the cmd.exe file and select 'run as administrator '.
  (4) in the CMD window, type: sfc/scannow
  (5) reboot and see if that solves the problem.
   
  If not, then in Safe Mode, take a look in the event viewer and see if the
  the events surrounding the last boot to normal mode give any idea regarding the
  cause. (Just use the app and the Windows system event logs for the)
  now)
   
  BTW - I saw boots to take more than 30 minutes of the Normal Mode - so make sure you
  sure leave you long enough!
   
  --
  Noel Paton
  CrashFixPC
   
  Nil Carborundum Illegitemi
  www.crashfixpc.co.UK
   
   

• Windows 7 does not start after the Welcome screen after password

  I've been running Windows 7 for the last 10 months with no problems until a few days ago. The PC starts fine, goes to the password screen, accept the password and then adheres to the Welcome screen.  The PC is not frozen, the cursor moves and the circle just keeps running load.  It starts perfectly in safe mode and safe mode with network.  This problem started to occur intermittently, but tonight, it took 4 re - begins to initialize.

  Would be grateful for any ideas.

  Hello
  
  a. did you software/hardware changes to your computer before this problem?
   
  Step 1: Try to perform the clean boot in safe mode and check. This is perhaps due to some third party software installed on your computer.
  Reference: http://support.microsoft.com/kb/929135
   
  Step 2: Also, look for error messages in the event viewer. If you find error messages after return the exact error message so that we can help you better.
  Measures to check the application event log:
  a. Click Start.
  (b) in the search box type eventvwr.msc , and then on enter.
  c. now, click Application in the event viewer (local).
  d. now, looking for event log on the right side of the event viewer window.
  http://Windows.Microsoft.com/en-us/Windows7/open-Event-Viewer
  http://Windows.Microsoft.com/en-us/Windows7/what-information-appears-in-event-logs-Event-Viewer

  Thanks and greetings
  Umesh P - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  [If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]

• Windows XP does not start after the interruption of the power supply

  Power was cut while the computer is running, now when you try to start the computer, it goes to black screen with options to start in safe mode, start in SafeMode with network, last good configuration and boot normally.

  I tried all the choices and put right back on the same screen. How to make the computer to boot normally without losing all my personal data of staored on the hard drive?

  Be careful to perform a repair installation.  If you have upgraded Internet Explorer (IE7 or IE8, for example) must be uninstalled before running the repair facility:

  "How to perform a Windows XP repair installation, if a later version of Internet Explorer is installed"
    <>http://support.Microsoft.com/kb/917964 >

  Your first priority should be to save your existing files.  My preferred method is to create a free Knoppix (Linux Live) boot CD and boot your machine from the CD.  This should give you full access to your hard drive and allows you to copy your files to an external USB drive or a network drive.  Afterwards, you may need to reinstall Windows, either from a recovery partition or your recovery CD.  Creating a Knoppix disk is as simple as downloading an .iso file and your function "Burn Image" program of CD burning to create a CD.

  Knoppix: http://www.knopper.net/knoppix/index-en.html >

  HTH,
  JW

• Windows Vista does not start after installing Linux OS

  original title: Windows Vista does not start after the installation of the Linux OS... Help!

  I installed Fedora 10 Red Hat Linux on my HP laptop and now each time it powers on, I can't do vista windows at startup.  Goes directly into Linux.

  I need to get back to normal.  Any help would be appreciated.

  I installed Fedora 10 Red Hat Linux on my HP laptop and now each time it powers on, I can't do vista windows at startup.  Goes directly into Linux.

  I need to get back to normal.  Any help would be appreciated.

  Hey Oscar Jose

  Download the correct ISO file and make a disk bootable from the link below

  Then use the Startup Repair option when you start from

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  or at startup press F11 to start the process of restoration of hp and see if you can reinstall vista from the recovery partition and place your machine, back to the way you bought

  warning you all data loss and 3 third-party programs that you have installed unless there is a non-destructive option in your hp recovery options

  Thirdly try to ask in a fedora forum to solve the problem, he has caused

  http://fedoraproject.org/

  Walter, the time zone traveller

• ITunes does not start after the installation of Windows 10

  ITunes does not start after the installation of Windows 10, 1511 version (OS Build 10586.164). ITunes version 12.3.2.35, 6 GB RAM, Intel i3 @3.3 GHz. Itunes and Ipodserver module will run by Manager jobs, but Itunes does not open. iTunes starts in SafeMode as explained in the link below (hold SHIFT and control on your keyboard while you open iTunes).

  Fix unexpectedly closes or problems of launch in iTunes for Windows - Apple Support

  Solution, according to this link, is:

  If the problem does not occur in Mode safe, remove any third party plug-ins iTunes: solving problems with third party plug-ins - Support Apple iTunes but the link has been archived, and I can't find any plug-ins installed iTunes. Any other ideas?

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  TT2

• computer does not start after the Windows XP logo window

  Windows xp home edition
  service pack 2
  Dell inspiron 1501

  1. computer does not start after the Windows XP logo window
  2 works well in safe mode, even connect to the external monitor
  3. I reinstalled xp many times, problem stil exist.

  All the answers?

  Hi dhanushm,

  1. What happens after the Windows logo screen?
  2. You receive an error message?
  3. You have security software installed on the computer?
  4. Have you performed an installation clean Windows XP and even after that this problem exists?

  Method 1

  As the computer starts up fine in safe mode there is a possibility that some third-party programs installed on the computer is the origin of the problem.

  I suggest that you configure the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See section to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  1. Click Start , and then click run.
  2. Type msconfig , and then click OK.
     The System Configuration utility dialog box appears.
  3. Click the general tab, click Normal Startup - load all device drivers and services , and then click OK.
  4. When you are prompted, click restart to restart the computer.

  Method 2

  If fails it above step can refer to the article below and try the steps mentioned, check if it helps.

  After the Windows Logo appears or after you log in to Windows, a Windows XP computer cannot display the wallpaper, a black screen or a blue screen

  http://support.Microsoft.com/kb/318027