Windows Embedded Standard 7 - compatible database tool box?

Similar Questions

• LabVIEW Runtime engine on Windows Embedded Standard 7 P 32 / 64-bit?

  Any who tried never to install and run the LabVIEW Runtime Engine (2011 or later version) on Windows Embedded Standard 7 P 32 / 64-bit?

  I'm trying to figure out if this will work, for example on a CX5120 PC Beckhoff embedded. I have to have some TCP/IP communication simple to exchange information with another PC, but nothing else, i.e. drivers, etc...

  I hope that someone tried to do already. I don't have the right equipment now to check it out.

  As NEITHER sells touchscreens with WES7 installed here: http://sine.ni.com/nips/cds/view/p/lang/en/nid/210551 it's pretty safe to assume that they used the RTE on WES7.

  But yes, it is done.

• IE 8 on Windows Embedded Standard 7 is extensible to IE9 or IE10? Is it possible to install other browsers? that is, firefox or google chrome?

  I have more than 10 thin clients with Windows Embedded Standard 7 with IE8. We are running a web application that crashes with IE8. I tried the upgrade to IE9 or IE10, but during the upgrade process, it stops and fails to install. I also tried installing various other browsers such as firefox and chrome, but they fail during the instalation.

  Is there a limitation with the installation of other browsers or IE upgrade with windows embedded standard 7?

  Hi Billy,

  The question you posted would be better suited in the MSDN Forums. See the link.
  http://social.msdn.Microsoft.com/forums/en-us/home?category=EmbeddedWindows

  Hope this information helps you.

• In XP, SP2, Windows Embedded Standard 2009, system to see the CF 8 GB Extreme like disk sets.

  Hi all

  I'll put up an industrial PC with reader CF card on the motherboard. The system come with a card CF 8 GB, XP SP2, Windows Embedded Standard 2009 installed. I want to keep this card as the master of the copy, so I buy a SanDisk CF Extreme 8 GB in replacement card. I managed to copy the image to the new CF card and make it bootable. However when XP is running, he still see the CF card as a removable drive C:\. Where as with the original card CF, the operating system see a fixed drive C:\. It's a way I can make the SanDisk CF card as a fixed disk, as I have a problem with the installation of the software.

  Unfortunately no you can go see it as fixed disk. SanDisk sells only fixed disk via the OEM channel cards. you will need to contact one of their OEM distributors and buy a card of fixed disk mode.

• Thin Client PC with Windows Embedded Standard 7/8 requirements?

  Dear support,

  Could you help us do I need a VDA or SA if we use

  Thin client, PC with Windows Embedded Standard 7/8?

  Thank you.

  Hello

  I suggest you to post the question on the TechNet Support link below. It is the team dedicated to the issue that you are facing.

  http://social.technet.Microsoft.com/forums/Windows/en-us/home?Forum=w7itpronetworking&filter=AllTypes&sort=lastpostdesc

  Do not hesitate to write us if you have problems with Windows

• Windows Embedded Standard Service Pack 3

  I use Windows Embedded Standard Service Pack 1 in my pos machine. I want to install a new application that is supports only Windows embedded standard service pack 3. I am trying to get the service pack 3 for windows embedded standard.

  I can't find something. Is it available?

  Please please someone help me.

  Hi Omar,.

  Since then, the query is related to Windows Embedded Standard Service Pack 3 installation. I would say that contact their support site to improve assistance:

  http://TechNet.Microsoft.com/en-us/windowsembedded/dd632975

  Thank you and best regards,

  John

• Deploy an image of Windows Embedded Standard 7

  Hello

  The company I currently outsources our computers, but in order to save money, I took it upon myself to develop our internal computers.  Right now, the company works with that offers us a computer, a hard drive (with a customized version of Windows Embedded Standard 7) and all the necessary material to hang all this.  Rather than spend me time for the redevelopment of the OS for our needs, I was wondering if I can just picture one of the drives that they provide for us (with software such as Norton Ghost) and flash the image on the blank hard drives.  Obviously, this made appear some questions when it comes to product keys, licenses, etc.  What I hope is, that once the OS image is flashed on the new hard drive, can I just change the product within the software key so that the version of windows in real and legitimate for each image I have flash.  In no case that I want to "pirate" software, just the exact configuration of the OS even for each hard drive.  Once the image is flashed on the new drive, a new product key will be purchased/provided for each hard drive that I Flash the OS.  We rely on the purchase of the exact same type/model computer that was provided for us the company, we outsource to, therefore, and this is one of the reasons why I want to do this way, drivers, etc. should not be a problem.  If someone can provide an idea would be great.
  If, for some reason, this is not possible and decide us to purchase a Windows Embedded Standard 7 license and install the drive, as well as any type of software development, we need to customize the operating system, is there a way to emulate easily configuring of the hard drives that we have in our possession now?

  I suggest you post the thread at http://social.msdn.microsoft.com/Forums/en/category/embeddedwindows for assistance. The reason why we recommend that you post to the most appropriate forum is that you can get the most qualified respondents pool.

• Windows embedded standard 7 toolkit

  I am currently installing windows embedded toolkit 7 on a computer that also runing the same operating system.

  The mother Board that I use is a GA-Z77M-D3H-MVP. The hard drive is a 500 GB.

  I ran the setup.exe as an administrator. I have set up the program I get an error requested 1117 error message could not be run because of an i/o device error. I ran a chkdsk on my hard drive that does not solve the problem. I also tried with a different hard drive that does not solve the problem. 4.5 Microsoft Framework is currently installed

  Hi Mica,

  Please contact Microsoft Community,

  The problem you are having is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public.

  Please post your question in the TechNet Forum.

  https://social.technet.Microsoft.com/forums/en-us/home?category=windowsembedded

  Hope this helps you solve the problem, if any question you can write us and we will be happy to help you further.

• Windows Embedded Standard 7 Support

  I have an Application using NOR-DAQmx and NOR-488. 2. it has been tested and run on Windows 7 Pro.

  This will install and work on WES7?  And if it will support NEITHER?

  Thank you!

  Thanks Ausitin,

  FYI: Both NOR-DAQmx and NOR-488. 2 install with PCI-6229 and PCI Express GPIB card.  No errors or complaints.  Preliminary testing seems good.

  Kind regards

  Bob

• You need to remove Windows Embedded dual-boot system.

  Original title: replacement of the Windows XP boot manager.

  Hello

  A few days ago, I installed Windows Embedded Standard on a PC that already had Windows XP on it. But (Windows Embedded) has been installed with a lot of system files missing (Task Manager, System Configuration and even the application to activate Windows was absent).

  The Windows boot manager that came with Windows Embedded could not be successful because I could not access "msconfig". It doesn't even have a "repair" advanced option.

  "Windows Embedded would be useless in 30 days, so I formatted the disc that contains the" management of the computer "in Windows XP.

  But Windows Boot Manager Embedded stayed with Windows Embedded as one of the options (Option low said "Earlier Version of Windows". This driver for the Windows XP boot manager).

  Is there a way I can get rid of him?

  Thank you

  DOM

  Hi Dom,

  Did you uninstall normal Windows XP or Windows Embedded Standard?

  If you have removed Windows Embedded and normal Windows XP still installed, you can use FIXMBR and FIXBOOT from the Recovery Console to restore the boot loader.

  For more information, please visit this link: Description of the recovery Windows XP for power users Console

  If you have removed the normal Windows XP and Windows Embedded, you can ask your question in the MSDN forums for assistance.

  http://msdn.Microsoft.com/en-us/windowsembedded/standard/dd673653

  Hope the helps of information. Please post back and we do know.

  Concerning
  Joel S
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• HP Thin Client running Windows Embedded don't profile with attributes DHCP

  My company has a large population of HP Thin Clients that are not attached to our AD domain and therefore cannot do dot1x because they have no certificates.

  We decided to do the profiling for these devices. We present a few attributes, two of these DHCP attributes.

  About 90% of our profile of thin clients, as expected, but the other 10% will refuse to work. We need to statically assign them to a group of identity to authenticate properly.

  A lot of troubleshooting reduced us to query DHCP the thin client sent was not received by the strategy node. A TAC engineer looked over the config switch, IP helper address configuration and said that everything seems to be configured correctly.

  The only explanation is that it seems that these specific thin clients were not finishing the DHCP process before reassigned switch the VLAN of the port. So when the dhcp request has been sent, the thin client was already in our vlan "invited" who does not dhcp to the ISE.

  It's very strange, because we have so many thin clients that works properly. It's only a handful that do not. We have not been able to further refine to something specific. They are running Windows Embedded Standard 7 and a majority of them are HP t5740. I don't see Windows or HP updates available for these units and not sure if there are any registry hacks available to expedite the DHCP process.

  Has anyone ever come across something similar to this?

  It's pretty obvious to me, the end point isn't you get profiled before there was authenticted, which means that you do not correspond to the profiling conditions defined in rules 6 and 7, which means it will match the rule 11 (I think, having not seen your real rules). What I expected this, is that endpoint gets profiled, if ISE receives the attributes of this endpoint via dhcp e.g. forwarding help. Then, what should happen is, that it should issue a certificate of authenticity to the switch, which will lead to the passage to be re - authenticate this ending point, which now must have customization attributes you are trying to match. However if the DHCP packet never reaches ise, it won't work. That's why I think you should do a trace of package on the ise server, to see if the packets actually reach ise. If they don't you will probably need to find another way to profile, or activate dhcp for assistance on your guest virtual local network. Have you looked at the attributes of endpoint maybe after 30 seconds? They change?

• Color Laserjet M252N: HP Color Laserjet Pro printer M252N for Windows XP Embedded Standard.

  I can't install the driver HP Color Laserjet Pro printer M252N to my machine (OS: Win XP Embedded Std version) without an internet connection.

  1 error message are requested in advance for MS .net framework 3.5. (after that, I download and installed: NETCFSetupv35.msi)

  I found the name of the printer in the list of drivers, but then I try to add a new printer with this driver, the pop-up error message and the installation is not complete.

  My question is: the HP Color Laserjet Pro printer M252N are not compatible with Win XP Embedded Std?

  Please help, even the HP sales technician unable to answer me to this questation.

  Hello

  The HP Color Laserjet Pro M252N Featuer software complete is not supported on Windows XP, however you can get the features of the printer using HP PCL 6 Universal Print Driver listed on page 9 of the User Guide, be aware that the Service Pack 3 must be installed on the operating system to use the printer:

  Make a right click my computer and select Properties - locate Service Pack 3 in this form... If Service Pack 3 is not the operating system MUST be updated first:

  http://h10032.www1.HP.com/CTG/manual/c04475955

  You can download the HP Universal Print Driver below:

  http://ftp.HP.com/pub/softlib/software13/COL39348/LJ-95977-14/UPD-PCL6-x32-6.2.1.20636.exe

  As Windows Embedded edition is an edition of the customized version no official support is guaranteed.

  It is a customized operating system version includes only the components of the operating system selected for specific needs.

  Those selected by the OEM computer and not necessarily include any component required by the HP software or hardware.

  Try to install the printer and see if this can work, however it can work as explained and may not only the manufacturer of the computer can respond if such material can be installed on the operating system or not...

  Kind regards

  Shlomi

• The printer and settings tabs in the HP Solution Center tool box, do all the windows.

  Tabs tool box, in the HP Solution Center, and the printer settings do not appear in these windows.

  I check to see if there is another way to access the settings of the printer before I ininstall and reinstall the printer and the HP software.

  Windows Vista

  DeskJet F380

  Previously worked

  Thank you!

  Hey @HoopsHopes ,

  Thank you for taking the time to post on the HP Forums today! Hope you enjoy the experience.

  I'm gathering that you have problems with your HP Solution Center and seek advice before uninstall/reinstall.

  My advice would be... to do a uninstall and reinstall. This you will get the updated version and save you to address the problem that you are experiencing. If you need help to uninstall it and reinstall, let me know.

  Can't wait to hear back on your part.

• Windows 8 Embedded Standard doesn't have a "Full Windows compatibility"?

  Hello

  I am trying to determine what version of Windows Embedded might be the right one for a particular product. The comparative table of features at https://www.microsoft.com/windowsembedded/en-us/windows-embedded-8.aspx indicates that the Standard edition version does not "Complete Windows compatibility". In the datasheet, I could, unfortunately, not to determine which features of Microsoft compatibility refers to. Does anyone know what restrictions apply?

  Thank you!

  Dominik

  Hello Dominik,

  Thanks for posting your question on the Microsoft community.

  The question will be better suited to the audience of professionals on the TechNet forums.

  I would recommend posting your query in the TechNet forums.

  TechNet Forum
  https://social.technet.Microsoft.com/forums/Windows/en-us/home?category=w8itpro

  Thank you

• We get an error "windows 7 was not compatible with my computer" during the download of Windows Media Player for Windows 7.

  * Original title: Windows Media Player for Windows 7

  It seems that my computer (windows 7) did not come with Windows Media Player. When I tried to download it, it has stated that windows 7 was not compatible with my computer and gave me a windows xp download. Why is this and how would I be able to get the version for windows 7?

  Hello

  What version of Windows 7 do you have? What is an "N" or "KN" version that doesn't include WMP 12?

  Start - type in the search box-> WinVer find upstairs and double-click it.

  Media Feature Pack for Windows 7 N and Windows 7 KN (KB968211)
  http://www.Microsoft.com/downloads/en/details.aspx?FamilyId=31017ed3-166a-4C75-b90c-a6cef9b414c4&displaylang=en

  ========================================

  If this did not help to tell us which version of Windows you have.

  ========================================

  Check the Task Manager to make sure that WMPlayer.exe is not already running, and if it is complete the process
  on this subject. Click right tab taskbar - TaskManager - process.

  -------------------------------------------------

  Make sure that Windows Media Player is on.

  How to enable or disable the features of Windows 7
  http://www.SevenForums.com/tutorials/5023-Windows-features-turn-off.html

  -------------------------------------------------

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  ---------------------------------------------------------------

  Do this to reregister the Jscript.dll and Vbscript.dll files.

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  type or copy and paste-> regsvr32 jscript.dll
  Press enter

  type or copy and paste-> regsvr32 vbscript.dll
  Press enter

  Restart and if all goes well, it will run now.

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.