Windows Image Acquisition Service

Similar Questions

• ERROR POPS UP EVERYTIME I OPEN AND IT SAYS WINDOWS IMAGE ACQUISITION SERVICE IS MISSING

  MISTAKE TO REPLACE ON VISTA

  Hello

  1. When you receive the error message?

  2. did you of recent changes on the computer?

  3. do you have a printer or a scanner connected to the computer?

  Method 1

  Check and make sure that theAcquisition of Image Windows (WIA) service is running on the computer.

  one), click Start-Run, type "services.msc", click on OK.

  (b) when loading the Services window, go to the "Service Acquisition of Image Windows (WIA), double click on it to open it,

  (c) make sure that the "Startup Type" says "automatic". " If it isn't, use the drop down menu to change.

  (d) if she once said: "Automatic", then click on the "Recovery" tab in the upper part and replace the line "First failure" "Restart the Service", then click on ""apply ', then OK. "

  Method 2

  If the previous step fails, see if any third-party program installed on the computer is causing the error message.

  To help resolve the error and other messages, you can start Windows Vista or Windows 7 by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See the link below to learn more about how to clean boot.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  (a) click Start, type msconfig in the search box and press ENTER.

  (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

  (c) under the general tab, click the Normal startup option, and then click OK.

  (d) when you are prompted to restart the computer, click on restart.

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• How do you get the Windows Image Acquisition (stisvc) service to restart?

  HP Pavilion DV6-2088dx running Win 7.0 64 Bit Ultimate

  When I try to restart the Windows Image Acquisition Service I get a message access denied (Services tab in the Task Manager) or an "error 1068: the dependency service or group could start" (in the Services window).

  Hello

  One thing to check is the following.

  Open windows control panel, open administrative tools, and then open Services.  Make sure that the following services (order of th specified below check them) are all showing that status = started and the Startup Type = Automatic

  Remote procedure call (RPC)

  Detection material core

  Windows Image Acquisition

  If you need to make a change to one of the above, just right-click the service and select Properties, and then in the drop-down list box next to "Startup Type", select automatic and click on apply to save the changes.  Then click on the Start button.

  Kind regards

  DP - K

• Windows Image Acquisition (WIA) is not listed in Services.msc

  I bought a new printer (HP Envy 4502) and it connected wireless to my PC. It prints and copies fine but when I try to scan (the printer and PC), nothing happens - message on printer says "computer does not.

  I tried with my firewall off and still nothing. (Use Bullguard security, windows firewall is disabled).

  After some research more advice is to check if Windows Image Acquisition is on, but when I look in the list of services there is no Windows Image Acquisition - in alphabetical order, he jumps 'Police Windows Cache Service' to 'Windows Installer' (accessible via the command Services.msc)

  I also tried to run sfc/scannow, but who doesn't.

  CHKDSK found no errors.

  I tried to download "Windows_Image_Acquisition.reg" and "RestoreWindowsImageAcquisitionWIAWindows7.bat" without success.

  What can I do to return WIA?

  How can I check what are the other missing services?

  Thanks in advance for any help

  Hello Jeff,

  Thanks for posting your question on the Microsoft community.

  Thank you for details on the question and your efforts to resolve.

  'Windows Image Acquisition' service provides image acquisition services for scanners and cameras.

  This problem may occur because of damaged or missing Windows files. This can also occur due to incorrect registry settings.

  Please refer to the suggestions marked as answer by Dale Qiao on June 16, 2010 and check if it helps.
  https://social.technet.Microsoft.com/forums/Windows/en-us/6b0e4eb7-3505-443a-9DCC-faf711743faa/has-anyone-seen-WIA-Statup-problems-in-Windows-7-ultimate-x64?Forum=w7itproinstall

  Note: Serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  http://Windows.Microsoft.com/en-us/Windows/back-up-registry#1TC=Windows-7

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• Windows image acquisition

  I can scan is no longer on my canon D480 image class. I get the message "windows could not start Windows Image Acquisition (wia) service on computor local e.» Error 1068 the dependency service or group could start

  Hello

  One thing to check is the following.

  Open windows control panel, open administrative tools, and then open Services.  Make sure that the following services (order of th specified below check them) are all showing that status = started and the Startup Type = Automatic

  Remote procedure call (RPC)

  Detection material core

  Windows Image Acquisition

  If you need to make a change to one of the above, just right-click the service and select Properties, and then in the drop-down list box next to "Startup Type", select automatic and click on apply to save the changes.  Then click on the Start button.

  Kind regards

  DP - K

• Problems to import pictures from my Canon Powershot A580 - Windows Image Acquisition?

  All the photos I import into Adobe transfer in a .tiff because of a TWAIN link images?  What I have read that I need Windows Image acquisition.  Can I download this?  If yes where?

  I used to do this with this camera without problems until a recent virus, now I can't it to work.
  Any help much appreciated!

  All the photos I import into Adobe transfer in a .tiff because of a TWAIN link images?  What I have read that I need Windows Image acquisition.  Can I download this?  If yes where?

  I used to do this with this camera without problems until a recent virus, now I can't it to work.
  Any help much appreciated!

  ==================================
  I have a Canon and everything I do is just copy the pictures
  of the memory card. I never install of the
  proprietary software.

  Have you tried to upload photos to a folder on
  your hard drive before import you them into an image
  editing program?

  If you insert the memory card from the camera into a USB port
  media player and go to... My computer... the media
  drive is listed as one or more removable disks...
  If you right click on the removable disk that corresponds
  You can see it with the location of your card is located in the files and
  copy and paste or drag and drop in a folder on your
  hard drive.

  If you don't have a media player... you can connect
  the USB camera and it should show in my computer. John Inzer - MS - MVP - Digital Media Experience - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - to proceed at your own risk

• WIA.dll; Windows image acquisition

  Tech support said Canon I can't install a printer driver, because a file is missing in my system Windows XP (service pack 3), specifically: wia.dll.

  How can I get the file or otherwise remedy the situation?

  Tech support said Canon I can't install a printer driver, because a file is missing in my system Windows XP (service pack 3), specifically: wia.dll.

  How can I get the file or otherwise remedy the situation?

  Are you sure you got the file name correctly?  WIA.dll is not a standard Windows XP file.  If your Canon printer to a file with this name, it must be included with your Canon printer software.

• 'Windows Image Acquisition' does not work

  This message has been appearing whenever I start my Windows 7 Professional 64 bit OS PC.

  I get a dialog box with the option of sending information to Microsoft, but nothing else to give an indication of what the error occurred or what action I might be able to take to correct the situation.

  Since I got this message at the start that I was also see a very slow page on some Web sites load.

  Is it possible to repair this problem of "reloading" WIA... If so where can I find the right software to download.

  Any suggestions are welcome.

  To complete this thread, I have a confession to make!

  It seems that the source of the problem was my scanner Canon LiDE 500F omitting "initializing" when starting. The scanner "purrs and snoring" as it initializes during the boot-up... something that I am so used to what I hear is really it... so I didn't notice that this was not the case, doh!

  Where the 'pilot' for the scanner does not load when starting because presumably the system failed because it could not 'see' the scanner.

  A violin with wired usb on the scanner seems to have solved the problem... much to my embarrassment!

  I hope you don't think that I've wasted your time auggy, because tips have led me to the scanner LiDE 500F as the source of the problem, but a physical connection instead of overflow of software problem. Thanks again.

• Image acquisition turns off in Windows Server 2012

  I am running Windows Server 2012.  Kind of a necessity, that I also hosts the website of our company.  All updates are installed, and desktop experience is enabled.  Image acquisition Windows is listed in Services, but was originally set to manual by default.  I tried just to start the service, but it stops automatically after about 30 seconds.  I tried the automatic configuration, but it does not start on its own.  I get no error message, and I checked dependencies, which seem fine departure, because repeatedly referenced in many other assignments.  Fresh ideas?

  Hello

  Post your question in the TechNet Server Forums, as your question kindly is beyond the scope of these Forums.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

  See you soon.

• "services.exe - bad image" and "the application or the DLL...\ShimEng.dll is not a valid Windows image.

  At the start this morning, I received the message following "services.exe - bad image" and "the application or the DLL...\ShimEng.dll is not a valid Windows image. Is there a simple solution to this problem? If it is ok, the unit freezes then

  Hello

  1. you remember to make changes to your computer, after which the issue started?

  I would recommend that you follow these steps and check if the problem persists.

  Step 1:

  I would recommend that you run a full scan using theMicrosoft Safety Scanner and check if the problem is related to malicious software.

  Note: You may lose data while eliminating malware.

  Step 2:

  Test the issue in a clean bootand verify if the issue.

  Note: Follow step 7 to your computer as usual.

  Step 3:

  Make SFC scan and check if the problem persists.

• Windows Imaging Component and Cryptography Service

  I'm in big trouble with installation of WIC: I can not install it because the Setup program indicates that I have no update.inf. In addition, my cryptography service is completely shut down and if I try to restart it I get error 1079. I tried the solutions provided on this community on these two issues, but they did not work for me.

  Can someone help me please?

  PS-I use Windows 8 Enterprise

  Hi Hastelloy,

  Thank you for being a part of the Microsoft Community.

  Before you continue with the troubleshooting steps, I would like to know some information about this problem.

  1. What is the exact error code or error message that you receive?

  2. have you installed any program Intel Rapid Storage on your computer?

  3. that all the troubleshooting steps have tried to solve this problem?

  4. is this problem limited only while installing the Windows Imaging Component?

  5. What is the number of brand and model of the computer?

  6. are you connected to a domain network?

  I suggest to check the following Microsoft MSDN blog and check if it helps. This blog explains Windows Imaging Components and Windows 8.

  http://blogs.msdn.com/b/chuckw/archive/2012/11/19/Windows-imaging-component-and-Windows-8.aspx

  Please respond with more information about this problem so that we can better help you.

• Windows 7, update services does not work

  I have a problem to update software in windows 7.

  I have a HP G72 laptop.

  I replaced my hard drive. 350GB, Western Digital 750Go digital West.

  -J' made an image of the C partitie (if it is 3 months, installed for the recovery partition, new updated worked after that).

  The new disk hard there however any possible updates of windows. (the bar is red on the left).

  -After that, I reinstalled the original image when the laptop was new (DVD image). Same result on updates.

  -Remove the folders from the dir c/windows/SoftwareDistibution, no results.

  -Checked the status of services: windows update is statred and in automatic mode.

  N ' tried microsoft 'Fix - it' no results.

  -updated the drivers intel, no results.

  -Downloaded System Update Readiness of windows to resolve the error (Windows6 1 - KB982018 - v3 - x 64). When installing, I get the error 0xc8000247. So I'm not able to install this software.

  Looked after errors in the CBS.log newspaper: found M²: cannot read the time value RptTime from the registry. [HRESULT = 0 X 80070490 ERROR_NOT_FOUND]

  Do a clean boot, without result.

  Does anyone know a solution to this problem.

  Thank you.

  Ed.

  Windows 7, update services does not, RESOLVED.

  The problem occurs when you change your hard drive for a bigger, in my hard drive of the case a GB Western Digital 340 WD 750 GB drive hard.

  For the Windows automatic updates again you need update the Intel Rapid Storage Technology Driverdriver. It will not be updated when you have intel check your drivers! For me, only the 9.5.6.1001 version worked. This driver can be found at http://support.hp.com/us-en/document/c02219204 .

  Versions available at https://downloadcenter.intel.com/SearchResult.aspx?lang=eng & ProductFamily = Software + Products & ProductLine = Chipset + Software & ProductProduct = Intel % c2% ae + Rapid + Storage + Technology + (Intel % c2% ae + RST) did not work for me (I tried the form version 12.8.0.106 08/08/2013.) Why does not the superior version is not clear to me.

  Good luck to solve you yours it took me two weeks to find it.

  Ed.

• Blocks the execution of the user Image Acquisition interface

  I am currently trying to create a user interface that displays images from a camera attached to a microscope with a mobile table.  The user is able to interact with the images and can click on them, which causes the table to move to a new location.  Acquisition is made by calling a DLL, the DLL grey flycapture point camera, using a call library function node.

  When I acquire images at 15 frames per second, it has no problem with user input.  However, when I drop the acquisition at 2 frames / second (necessary if you need to have the exposure time), labview seems to take a break from the user interface while the image acquisition is underway.  Interaction of the UI seems possible in the holes between the image acquisitions.

  I'm sure that this is happening because there is a kind of blocking going on here.  The program is waiting for the new image to be returned and will not not something else happen while he waits.  I have image acquisition running in a separate, called function from a higher level, VI, which puts the image data in a global variable (I know I know... global variables).  When I need to display the image, I read of the global variable and display it on my form of user interface.

  I think I need to run things in separate threads to avoid the problems that I have because I have a dependency that is the cause of blocking.  I'm looking for any suggestions on how I can the architect this.  I have thought about using a VI server to launch the acquisition of the camera and will try to implement this, but I wonder if there is another method that I'm missing here.

  Any suggestions would be greatly appreciated!  I use LabVIEW 8.6 on a Windows 7 machine indeed.  I do not use LabVIEW image acquisition module.

  Thank you

  Hey Gerry,.

  It's Paul in Ministry here at National Instruments engineering applications. What Paul was referring to a call library function node configuration properties. If you right-click on the node library function call you can click on configure and you should see a window that looks like the image below.

  

  As you can see, you have the option to select run this library in the UI thread or any thread. This is important because there is only a single user interface thread. Therefore, deadlocks can occur when the code is written in parallel, but operations are both occurring in the UI thread. What results is a part of the code has to wait that the other part at the end and so the lock upwards in the user interface. The reason why the call library function node is set to run in the default UI thread is now, because only the security thread functions can be performed in any thread. So before you change this configuration it is strongly recommended that you check that the functions you call are thread-safe. You can also check which configuration, the node library function call is in the color of the node itself. If it is an orange color which means that it is set to run in the UI thread. If it is a pale yellow color, it is set to run in any thread. Let me know if you have any other questions!

  Paul M

• Problem with setting window of acquisition on 1429 PCIe capture card

  Hi all

  Recently, I am using the Basler A504k camera with card PCIe-1429 of goodwill for the acquisition of images at high speed. I found problems with setting the acquisition window in the capture card using Measurement & Automation Explorer.

  1. for example, if the size of the original image is 1280 * 500, if I put the window of acquisition with left 0 and width 1280, everything is OK, but if I set the width to 1279, there will be an error (error 0xBFF6002C FIFO overflow caused the acquisition of stop), if I set the width multiple of 8, there was no error. Could someone tell me why in this case, is it because the packet data transfer for acquisition card rule?

  2. the window of acquisition is set according to the camera image, right? If the camera has also a function of area of interest, the acquisition window setting is always the image coming from the camera.

  Attachment is my setting a MAX software.

  Thank you very much

  Hi xiaochunfly,

  My bet is 1280 pixels image size is aligned on 32 bytes, and the material may actually go from line to line without breaking the transfers. With the width of the non-aligned countries, he needs to start a new transfer on each line, and this has an additional load on the PCIe bus and the system memory bus. Currently infrastructure IMAQ trying to adjust to any size of border/size possible image regardless of efficiency, it take the material and changes in recent processor Intel chipsets have reduced effectiveness with system memory bus performs under these conditions. So, you can get much better performance if you use line widths. You can also get the latest IMAQ driver because there was changes in the latest few transfer more effective under some of these conditions.

  AOI is usually under the framegrabber. If you reduce the AOI who sends the camera, it seems often identical to the framegrabber as if you just had a camera with a smaller sensor. Thus, your AOI in IMAQ must be set to the size of that the camera is sending, unless for some reason you want to capture less of what the camera is able to set up on its own.

  Eric

• Can what "Windows Imaging Component' (WIC) I download?

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=32

  What WIC download?
  I need to know, so I can download .NET Framework 4.0

  I have:

  OS name: Microsoft Windows XP Home edition
  Version: 5.1.2600 Service Pack 2 Build 2600
  OS manufacturer: Microsoft Corporation
  System manufacturer: TOSHIBA
  System model: Satellite A105
  System type: X 86-based PC
  SMBIOS Version: 2.31 - what is - this?
  Layer of HAL: Version = "5.1.2600.2562 (xpsp.040919 - 1030)"-which is the Hardware Abstraction Layer?

  -------
  If you need more information, let me know.
  You do not need to respond to the additional questions, but would be appreciated.

  Hello

  I suggest you to download wic_x86_enu.exe from following link:

  Windows Imaging Component
  http://www.Microsoft.com/en-US/Download/details.aspx?ID=32

  What is SMBIOS?

  System Management BIOS (SMBIOS) is a data structure exported by BIOS latest on x 86 platforms, including those currently produced by Sun. SMBIOS is a standardized software system low level export configuration information material as high-level system management software. The SMBIOS itself data format is defined by the DMTF Distributed Management Task Force (). Seedmtf.org if you want to read a copy of the specification itself.

  From: https://blogs.oracle.com/mws/entry/smbios_support_for_solaris_x86

  Layer of HAL
  http://msdn.Microsoft.com/en-us/library/aa915144.aspx