Windows Setup.

Similar Questions

• HP dv6 7214tx: windows Setup could not configure windows to run on this hardware

  Hello

  I know it has been posted similar problems before, but I still can't get on my instalation.

  I came to this point: during installation PROCESS, almost at the end of this message pop up "'WINDOWS Setup COULD NOT CONFIGURE WINDOWS TO RUN on THIS COMPUTER HARDWARE".

  My PC is: ENVY dv6 7214tx

  3rd gener. Intel Core i7-3630qm

  processor 2.4 GHz

  1 TB HARD DRIVE

  8192 MB DDR3 SDRAM

  Blu - ray optical drive

  Windows 8

  NVIDIA GeForce graphics card

  WLAN & Bluetooth

  I changed boot to the DVD - ROM option, SUPPORT of LEGACY enabled, disabled SECURE BOOT.

  What it might useful to you guys, it's the actual installation takes apx. 5 hours, then he came to the point of pop up window mentioned above.

  Do you have any suggestions please?

  Thank you very much

  .. .also even if this driver has been loaded to the top, another window pops up and says smth like "the driver is not signed, and it might not work.

  However, I let it install... I'll see

• Satellite P300 - 18 M - Windows Setup cannot continue

  Hi, my first post here, hoping for any help.

  I recently bought a Satellite P300 - 18 M, from an independent retailer with no return policy. good on the PC is a brand new, sealed, etc and I get the Toshiba standard warranty.
  When I do the initial installation I received a message all in settng upward of Windows Vista Home "the computer restarted unexpectedly or encountered an unexpected error." Windows Setup cannot continue. To install windows click on 'OK' to restart the computer announced then rstart installation. »
  I tried a few times more full-time catering and the third HARD drive it installed, but...
  either he starts, I get to the password screen then all invent locks, the mouse pointer freezes then the screen becomes full of horizontal lines.

  or

  I've had a few times in windows for a few minutes (2-5 minutes) then the mouse pointer freezes, 3 seconds later the entire screen is full of horizontal lines, everything locked can only turn off the coast.
  Toshiba software error, so no warranty claim and advised that I buy the DVD (£29.90) that I ordered it, on a delivery of 14 days of recovery.

  Any other help or suggestions much appreciated as im not confident of this DVD, being a brand new sealed unit, why corript of Vista in the first place.

  Thanks in advance

  Andy

  Hello

  In my view, that the P300 is equipped with the ability to drive HARD recovery. This means that you could restore the operating system of the image that is stored on the HARD drive.
  To do this, you will need to power the laptop and must press the F8 key.

  A start menu should appear, then you should choose the first option called fix my computer.
  Then, you must choose the option called Toshiba HDD recover or something like that. It should be the last option.
  This procedure helps you reinstall Vista again.
  This facility could be that you can burn the own recovery disk using the preinstalled software called Toshiba Recovery Disk Creator.

  But if the recovery of HARD drive does not work you will need to use your orderly recovery DVDs and have to restore it again.
  If the laptop will not properly work after using Recovery then DVDs I recommend to contact the ASP again and to explain the whole story.

  Good luck

• HP Pavilion dv6-7028tx Enterta: Windows Setup could not configure windows to run on this hardware

  As I tried to reinstall win 7 on my laptop HP Pavilion dv6-7028tx, the competition, Enterta I received this message by win7 saying that «windows Setup could not configure windows on this computer hardwear»

  

  I did some research on this issue, it seems to be the lack of SATA drivers on my computer.

  Could you please tell me which intel SATA driver should I install to fix the problem?

  If this method does not work, then please can you me how to change the hard drive in AHCI or IDE BIOS setting?

  Thank you very much

  Hello:

  You cannot change the drive controller setting in the BIOS on any HP laptop consumers made in the last 5-6 years.

  See if it works...

  Download the drivers from this link below (first listed file - 64-bit).

  https://Downloadcenter.Intel.com/Detail_Desc.aspx? AGR = Y & ProdId = 2101 & DwnldID = 23060 & keyword = Intel + Rapi...

  Extract (copy) the files on a USB FlashDrive without all records.

  With the flash player and support installation of W7 in the machine, boot from the installation of W7 media.

  After selecting the install now option, select the training - Advanced menu, Options and select the option load a driver.

  You should now see the storage driver files listed.

  If you check the box, it only includes the compatible driver.

  Follow the prompts and I hope, will install W7.

• Windows Setup could not configure windows to run on a hardware on this computer

  HP Pavilion Sleekbook 15-b023cl

  I tried to install Windows 7 on my computer for the last day and after several attempts the same error message. It is said: "Windows Setup could not configure windows to run on a hardware on this computer." How would I go about fixing this problem?

  Thank you

  Hello:

  I'm not sure that there is a 'one size fits all' answer to this problem, if you google the error.

  The most common solution is to try to install the SATA driver.

  Here is the link to the SATA drivers you need for your model. Download and extract to a usb flash drive.

  First file listed is for 64-bit operating systems.

  https://Downloadcenter.Intel.com/Detail_Desc.aspx?AGR=Y&DwnldID=22194&ProdId=2101&lang=eng&OSVersion... =

  Use the Drive Options - Advanced method to install and then select the option load a driver.

  If you check the box, only the compatible SATA driver is selected.

  See if it works.

• Windows Small Business Server 2011 - "windows setup cannot continue because a required driver could not be installed.

  Hello

  I try to install windows server enterprise on my hp proliant gen 8. I used smart supply and that everything was working fine, when switching to the windows installation it gets to 99% then comes up with the error:

  Windows Setup cannot continue because a required driver could not be installed

  I was wondering what I can do to solve this problem, I have tried several times without success. Thank you for your time.

  Hello

  Your Question is beyond the scope of this community.

  I suggest that repost you your question in the Forums of SBS.

  https://social.technet.Microsoft.com/forums/en-us/home?Forum=smallbusinessserver

  "Windows Small Business Server 2011 Essentials online help"

  https://msdn.Microsoft.com/en-us/library/home-client.aspx

  See you soon.

• Windows Setup has not finished.

  Hello

  I reinstall Windows XP on a Dell Dimension 4500 with a Dell Windows XP Pro SP3 recovery disk. I followed all the steps to reinstall. I deleted the old partition and installed chose NTFS quick format. The installation went fairly smooth until I got the Windows Setup screens. It had an error message saying that it could not install some files but installation suite. Then I got an error saying that it could not connect to the internet. After that, everything went find until it restarts. He was about to read the Windows XP welcome video until it froze. All that appeared was a white screen with the Windows logo in the upper left corner with an 'X' on it. So I let it sit for about 45 minutes, and then I turned off the computer and deleted from the drive. From the beginning it upward, I found that it created an administrator account and it lacks many things. Also, I can't connect to the internet.  Here is a list of what is missing:

  • Photos from account.
  • A few wallpapers (Bliss, Azul and all others on the theme nature wallpapers)
  • The internet connection wizard.
  • Windows Media Player
  • Outlook Express
  • Help & support
  • Start menu customization options.
  • Remote assistance.

  Most of the drivers installed except a few including Ethernet controller.

  What hurts? and how to fix it? Here are a few screenshots that might help.

  

  

  

  

  It is an old system (with an old optical drive) and Windows XP has reached end of life 1 year ago, his insecurity and preferable to use only not etc etc. Assuming that you know this and to install Windows XP in any case.

  The first problem you have is the optical drive cannot read all the files on the CD and it ignores certain files, probably the laser in the struggles of optical drive with files from certain angles. If you have a newer PC with an optical drive to best, install ImgBurn (make sure that you opt for a facility advanced opting to not install any unwanted preloaded toolbars...). Create a .iso CD image, and then use ImgBurn to burn this .iso to more than 3 CD image. When the installation files cannot be read on the CD instead of exchange for one of the copies to jump. The file will be in a different location on the CD and it will be able to copy the file.

  The second question is you have devices connected to the system which may interfere with the installation of Windows. Its better to attach only keyboard, mouse and monitor. You had a brother printer attached...

  The third point is that you have not installed all the system drivers... I recommend that you use the old version of WSUS offline update to download all the updates of Windows XP (on a new work computer from a USB flash drive) before you install the drivers for your system:

  http://dellwindowsreinstallationguide.com/WSUS-offline-update/obtaining-the-latest-service-packsbuilds-of-Internet-Explorer/patching-Windows-XP-fully-using-the-WSUS-offline-update/

  You can then download the system from the Dell FTP site drivers drivers and downloads may not work for an XP machine (on a new work computer from a USB flash drive):

  http://downloads.Dell.com/published/pages/dimension-4500.html

  You will need to install the drivers in the order, which is particularly critical for Windows XP works correctly:

  http://dellwindowsreinstallationguide.com/downloading-drivers-checking-hardware-IDs-and-downloading-and-installing-Dell-system-drivers-in-the-correct-order/driver-installation/

• How to solve a problem when the windows setup program does not open a program, says I need to install it. and an error message 1706

  How to solve a problem when the windows setup program does not open a program, says I need installation cd and a 1706 error message happens.

  Hi PAtwoodwu,

  1. what program are you trying to install?

  2. did you of recent changes on the computer?

  3 does happen with all programs?

  Check and make sure that the Windows service install is running on the computer.

  (a) click on start to reduce this includes this image, click run , type services.msc , and then press enter to open Services.

  (b) right click on the Windows Installer service and then click Properties.

  (c) if the box Startup type is set to Disabled, change it to Manual.

  (d) click on OK to close the Properties window.

  (e) right click on the Windows Installer service and then click Start. The service should start without errors.

  (f) click on the file menu, and then click exit.

• START WINDOWS VISTA ERROR "the computer restarted unexpectedly or encountered an unexpected error." Windows Setup cannot continue. To install Windows, click "OK" to restart the computer, and restart the installation.

  I have a portable Gateway that will not start, but rather when I turn on the laptop, it gives me a box of caption read "the computer restarted unexpectedly or encountered an unexpected error." Windows Setup cannot continue. To install Windows, click "OK" to restart the computer, and restart the installation. I bought the recovery CD gateway and even made the recovery discs offered by Microsoft, but nothing helped. Or recovery CD were no help. I am running Windows Vista. Any suggestions?

  I have a portable Gateway that will not start, but rather when I turn on the laptop, it gives me a box of caption read "the computer restarted unexpectedly or encountered an unexpected error." Windows Setup cannot continue. To install Windows, click "OK" to restart the computer, and restart the installation. I bought the recovery CD gateway and even made the recovery discs offered by Microsoft, but nothing helped. Or recovery CD were no help. I am running Windows Vista. Any suggestions?

  Hey PeLon416

  If you have problems with the gateway recovery process, you will need to contact Gateway

  It's their recovery process not microsofts

  You may have a hardware problem

  support of bridge at the link below

  http://support.gateway.com/support/default.aspx

  Walter, the time zone traveller

• Windows Update has been returning a message "windows setup is not be accessible" and the error # 641 & 80070641

  The items to be updated were NET & updates Office 2007-12 in all. -# 641 & 80070641 error message. This problem lasts 4 weeks. I tried all the "fixes" that I could find on the Microsoft Web site, which included using their "fix", many, many other options. ". Then these time, other programs could also not be updated because of this problem.

  Through frustration, I decided to reformat the C drive two days ago.

  After obtaining any return on the system, it worked for a day. Then, I received a message on the screen saver photos - "the application failed to start because MSVCR100.dll was not found. Return to the site to find a solution. I tried everything I could find including trying to download M Visual C ++ 2008, 2010. Now the original problem returned - "windows setup is not be accessible...» "so he could install anything. Previous updates that couldn't be downloaded have been uploaded in the update after reformatting & before the return of the problem. I would have thought that reformatting should have solved the original problem.

  If anyone can help.

  Thank you

  I think I found the answer to the problem. After several formats, I decided to leave a bit special to the end of loading software.

  Up til then my system seems to work perfectly, but when I loaded this software, all the old problem returned.

  Software is turned off through Dell and called Dell PC tune-up and was intended to keep your pc clean & working fine by clearing up junk, protecting the registry etc. It is now called System Mechanic. I don't know why it should cause a problem now that I've been using the product for more than 3 years, but it is certanly the problem with my pc...

• «.. . restarted quit unexpectedly or encountered an unexpected error. Windows Setup cannot continue... »

  "The computer restarted unexpectedly or encountered an unexpected error." Windows Setup cannot continue. To install Windows, click "OK" to restart the computer, and then restart the installation. »
  
  I have this error message and called technical support from microsoft, we have tried to reinstall Vista again once I had tried three times with the same error message. It would freeze to "complete installation." even let him all night to see if he needed more time to complete on its own, but nothing helps...

  the technician told me I have a hardware problem, but when I installed XP on it everything works correctly.

  It's a new pc and a clean install of Home premium. I re-post this question since yesterday

  Hi evan9074,

  So was the question then? You can run the Windows Vista Upgrade Advisor to see if there are compatibility issues that you have with hardware or software that would prevent an upgrade to Windows Vista.

  I hope this helps.

  Brian
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows Setup could not configure windows to run on this hardware

  I am trying to install Win 7 on a HP Pavilion dv6-7012tx laptop. He brings Win 7 by default. I installed win8 once. Now I can't reinstall win7 on laptop in May. He tried to install Windows 7, but when the computer restarts and tries to complete the installation, I get the following error: "Windows Setup could not configure Windows to run on hardware of Cet_Ordinateur."

  

  My laptop configuration:

  By default the operating system: Win7

  Processor: Intel 2nd generation Core i5

  GPU: NVIDIA GeForce 630 M

  Hard disk: 640 GB (SATA II)

  RAM: 6 GB DDR3

  Hello:

  If you use an ordinary W7 installation DVD and use no recovery disc, the most common cause of this error is the lack of SATA drivers.

  Download and extract these files on a usb flash drive. First file listed is for W7 64 bit.

  https://downloadcenter.Intel.com/Detail_Desc.aspx?agr=Y&ProdId=2101&DwnldID=23060&Keyword=Intel+Rapid+Storage+Technology+(Intel+RST) & lang = fra

  Plug the flash drive into your laptop and start your installation of W7 DVD.

  When you get to install it now click on that and click the option advanced player options.

  Then choose load a driver.  You should now see all the sata on your USB drivers.

  You can check a box and it will include the compatible sata driver to install.

  Proceed from there, and I hope that will install W7.

• Relocation of 7 home 64 bit by usb. Windows Setup needs a driver. message reads (a required CD/DVD drive device driver is missing).

  54i have a computer laptop m18x by Mei alineware reinstall 7 home 64 bit by usb. Windows Setup needs a driver. message reads (a required CD/DVD drive device driver is missing.) funny iam not to use a cd or a dvd. IAM using a USB flash drive. weird. If anyone can help.  Thank you wberlin

  Probably the installation media itself is corrupt. If your Alienware is preinstalled with Windows 7, then you should be able to reinstall using the recovery partition:

  New computers that come pre-installed with Windows often have what is called a recovery partition. This is used to reinstall an operating system in the case of a system failure. To access it, you need to start when you start your computer by pressing a function key. This can be either F1, F2, F9, F10, F11, F12 key DEL or tab. See the manual that came with your PC for instructions on how to reinstall Windows.

  To restore the image while preserving the data files:
  Turn off your computer.1.
  Disconnect all devices connected to the computer (such as USB key, 2 printer and so forth) and remove any recently added hardware in-house. NOTE: Do not unplug the AC adapter cable.
  Turn on your ordinateur.3.
  When the Alienware logo appears, press several times to access the 4. Advanced Boot Options window. NOTE: If you wait too long and the operating system logo appears, continue to wait until you see the Microsoft Windows desktop; then, shut down your computer and try again.
  Select 5. Repair your computer.
  Select 6. AlienRespawn and backup emergency in the System Recovery Options menu and follow the instructions on the screen. NOTE: The restore process may take an hour or more depending on the size of the data to be restored. NOTE: For more information on AlienRespawn, see article 353560 at support.Dell.com knowledge base.

  Source:

  http://support.Dell.com/support/eDOCS/systems/M18x/en/mm/MM_en.PDF

  If the recovery partition does not work:

  Step 1: Download a copy of Windows 7:

  For 5 years, Microsoft made it fairly easy for users of the Windows 7 operating system to get reinstall media. If you have lost your support disc or installation retail collection; either it has been damaged or defective; You can download a copy of the edition that you have licensed from a membership site called Digital River. More recently, Microsoft ended the availability to reinstall media that you can download as a. File ISO in Digital River, which is a digital reproduction of an optical disc.

  It was particularly convenient for people who could not easily get the manufacturer's recovery media, did not want to pay the fees required to get or preferred a clean configuration without the software packaged manufacturers or even a recovery partition does not work. It's easy to use, all you had to do was reinstall and reactivate using the product key located on the certificate of authenticity and download all the drivers on the manufacturers website.

  Given that this option is no longer available, what are your options? See the article for more details:

  How to: What are my options for Windows 7 reinstall media?

  Make sure you scroll down and read the section:

  What to do if you cannot get your manufacturer recovery media, refuse to use or to buy it or the Microsoft Software Recovery Website does not work?

  Step 2: Perform a custom installation, see Windows 7 section of the following article how to perform a custom installation:

  How to: perform a customized Windows installation

  Step 3:

  http://techingiteasy.WordPress.com/2012/04/13/how-to-activate-Windows-7-OEM-license-using-a-retail-disc/

• Receive error message when you install Windows 7 "Windows Setup cannot find a location to store temporary installation files.

  * original title - Windows Setup is unable to find a place to store temporary installation files. To install the winds make a partition on your startup disk has at least 686 MB free space *.

  Current operating system: Windows XP SP 3

  Windows 7:32 - bit Premimum Family Pack upgrade

  Hardware: Dell dimension 3000

  I read a number of different solutions for this problem.  None have worked.  I have 25 GB of free space on my C drive.  I formatted a dvd using the tool to download Windows 7 USB DVD.

  I ran sfc/scannow to repair system files

  I ran the suggestion to start installing from a command using D:/setup.exe /tempdrive:c window - it did not work.

  Does anyone have any other suggestions on how to perform this upgrade?

  Try these suggestions:

  Error 0 x 80070005 occurs if the upgrade doesn't have permission to the folder writecertain. Try the following steps:

  Reset permissions
  ============

  1 if please download the subinacl.msi from the following link and save the patch to installation on the desktop:

  http://www.Microsoft.com/downloads/details.aspx?FamilyId=e8ba3e56-d8fe-4A91-93Cf-ed6985e3927b&displaylang=en#AffinityDownloads

  2. go to your desktop and double-click on the downloaded file.
  3. Please select the C:\Windows\System32 folder as the Destination folder during installation. Later, we will use this tool to reset the permissions on the current computer settings.

  4. click on the button 'Start' in the 'Search' bar type: "Notepad" (without the quotes) and press ENTER.
  5. copy the following commands, and then paste them into the opened Notepad window:

  off @echo

  Subinacl /subkeyreg HKEY_LOCAL_MACHINE/Grant = administrators = f
  Subinacl /subkeyreg HKEY_CURRENT_USER/Grant = administrators = f
  Subinacl /subkeyreg HKEY_CLASSES_ROOT/Grant = administrators = f
  Subinacl % lecteur_systeme % /subdirectories / Grant = administrators = f

  Subinacl /subkeyreg HKEY_LOCAL_MACHINE/Grant = system = f
  Subinacl /subkeyreg HKEY_CURRENT_USER/Grant = system = f
  Subinacl /subkeyreg HKEY_CLASSES_ROOT/Grant = system = f
  Subinacl % lecteur_systeme % /subdirectories / Grant = system = f

  @Echo =========================
  Completed @Echo.
  @Echo =========================
  @pause

  6. After you paste the above commands, please close the Notepad window. Choose "Save" when you are prompted to save the file. Type "reset.bat" as the file name and choose "Desktop" in the Panel on the left as the save location.

  7. refer to the desktop and right click the reset.bat file, then choose "Run as Administrator".
  8. you will see a window of type BACK treatment.

  NOTE: It may take several minutes, please be patient. When it is finished, you will be prompted with the message: "finished, press any key to continue."

  If the same thing happens, move to the next step.

  Run the upgrade by using the built-in Administrator

  ================================

  1. click the button start-> all programs-> Accessories.

  2. right click on command prompt and select "run as Administrator".

  3. click on continue when user account control window appears.

  4 copy the following command and press ENTER:

  NET user administrator / Active: Yes

  5 restart the computer and then log on the computer of this administrator account.

  6. run the upgrade to windows 7.

  Error code 0 x 80070005 usually indicates that you don't have enough privileges or the operation is blocked. I know, some programs (Boot Camp on a Mac PC, etc.) is not compatible with Windows 7, if you have installed these programs on the computer, you may not be able to perform the upgrade.  You should uninstall these programs before upgrading. In addition, such a question may be related to UAC, I recommend you turn off UAC in Windows Vista, if you have installed security software, try uninstalling the security application as well.

  BTW, for your references, I found similar questions:

  Windows could not create a required installation folder. Error code: 0x80070005
  http://social.technet.Microsoft.com/forums/en-us/w7itproinstall/thread/d04e9cf3-3eae-4A1F-a9f8-e2c5ed88d183/

  "Cannot create file" error when you try to install Windows 7
  http://social.technet.Microsoft.com/forums/en/w7itproinstall/thread/3621e8cf-B2CE-479b-BEAC-08acc435a856

  Error 0 x 80070005 when upgrading to windows 7 from vista
  http://social.technet.Microsoft.com/forums/en-us/w7itproinstall/thread/08986904-c822-4801-95a5-55ddd5aadcea/

  See also:

  http://social.answers.Microsoft.com/forums/en-us/w7install/thread/cb679e27-f2e6-4CD5-b708-a4992cec5a9d

  CREDIT: Dale Qiao Microsoft, host and cdobbs releasing It Easy: with Windows | ActiveWin | Laptops | Microsoft MVP

• Windows Setup could not configure Windows on hardware of this computer Installation error on the new hard drive

  Okay so if please bear with me and be patient.  I'm not tech savvy.  I know enough to be able to remove an old hard drive and put another one, but when there are errors, I don't know what to do.

  Here's the situation.

  I have a Dell Studio XPS with Windows 7 installed.  I started having these notifications that my hard drive could be a failure.  I tried everything that I could find to fix it without having to buy a new HARD drive without success.  The current system has a 1 TB Seagate hard drive.  I installed a memory additional bar thingie right after that I got the computer about 4 years ago.  (If someone tells me how to find the properties of real system, I post them if necessary).  Anyway, I bought a new WD 1 TB black disk hard to install before my old dies and loses all my photos and documents, etc...

  I took the old drive yesterday and installed the new hard drive.  I put back the case and turned on the machine.  I put in my Windows 7 installation disc.  He began installing Windows 7... It's completely past the initial screen where it says it to load it and the other... I had accepted the license agreement, but did not have to make a profile and do the work and the reader.  I hope all this makes sense.  Then it pops up this message "installing Windows could not set up Windows on hardware on this computer."  I couldn't figure out what to do from there.  I got the new drive and put the old one back to and here I am. I tried to find solutions to this problem, but I either don't can't make heads or tails out of the responses on the internet or the solution is not exactly my problem.

  Please help if you can!  And if you have any suggestions, please dumb them down so I can understand what to do.  I CAN do if loaded, you just have to not talk too irritable.  Laughing out loud

  Thank you in advance!

  Maybe not...

  The Windows installation is not happy about something, and since it gets at least started which is a good thing, but your installation problem can not really be with Windows - perhaps something about Dell hardware or your 1 TB HARD drive.

  I looked at your system and found this article that you can read to see if it sounds like your original question:

  Windows Setup could not configure Windows on hardware on this computer.

  http://www.Dell.com/support/article/us/en/19/SLN293812/en

  Since Dell has written an article for help on this subject, it means they've met enough times to take the time to compose the article and put it on their WWW site (but, they say, it is a possible resolution).

  Could you take the issue in the Dell online community where experts hang out (especially your amber light).

  Another good place for support is www.bleepingcomputer.com where there is a similar topic as your question (except Vista) on a Dell and a new disk of 1 TB (also a Seagate) and Dell ideas did not work, but someone else has found a way to fix it:

  http://www.bleepingcomputer.com/forums/t/453378/installation-fails-to-complete-on-new-HDD/

  The bleepingcomputer for your error message search reveals other areas and people who have got things to work in different ways, then it is perhaps another place to look for ideas.

  If the installation still fails it would not hurt to do the BIOS setting and see if things are getting longer, and since you are going to write the current settings before proceeding with the adjustment you can always cancel the adjustment if things get worse.

• Remove 'Windows Setup' to start upward

  My upgrade Windows Vista Home Basic SP2 to Windows 7 Home Premium is not successful.  This created a "Windows Setup" when I start my PC and invites you to me re-install again.   I did several times without success.  So I decided to go back to my Windows Vista operating system.

  Can someone tell me how to remove this "Windows Setup" when I start or restart my PC?.   If possible my Windows Visata will start automatically.

  The start menu with EasyBCD by NeoSmart Technologies edition should solve your problem, it provides a graphical front-end to the BCDEdit Command line that makes it easy for you to set the boot settings and change the entries start on the new window manager.

  http://NeoSmart.NET/DL.php?id=1

  Questions about installing Windows 7?
  FAQ - Frequently Asked Questions from Installation Windows 7 & responses