Windows slow Lenovo Z510 8.1 start-up

Similar Questions

• Lenovo G580 - menu to start cannot find CD/DVD, HARD drive

  Hello everyone

  I have a little trouble with this laptop lenovo G580, which cannot start.

  Problem: HARD and CD/DVD drive is visible in the tap in the bios info, but they are not visible in the faucet of the boot, only an IP4 and IP6 EFI network are visible.

  I tried to change the HARD disk first to ensure if she would do anything, but did not work, so I spent back.

  But I've never seen this kind of problem before, so I really have no idea what to do.

  The version of the bios installed is V9.01 I hope that if someone has an idea that could help solve this problem.

  -Mootix-

  It seems ok I solved my problem, I will report how and what I have done, so anyone with the same problem can try this.

  OK, so apparently the Bios have been installing only the boot devices to reqister who had something to do with Windows 8, which means that the hard drive that was completely empty of any data, had nothing to do with Windows 8 and therefor can not be started with the current Bios settings.

  1. open the safety valve and turn off temp only "secure startup.

  2. go to the tap of Boot and change 'Boot mode' for Legacy Support UEFI.

  3. in the tap water Boot changes 'Boot prio' "first Legacy.

  4 reboot and press F2 and verify tap boot to the disk under "Boot device prio.

  Fact

  I think that since the drive HARD have Win8 installed it will not display as boot device unless it is on Legacy Support.

  because UEFI on the G580 only supports the HARD disk with a Win8 installed operating system.

  Now, I should be able to reinstall Win 8 - 8.1 on the HARD drive.

• Lenovo Y500 does not start

  Hello

  I've had my y500 ideapad for a few years now. One day, my computer froze completely in normal operation. I had to hold the power button to do a manual stop. After that, my computer will not turn back. When I try to start it, I see a black screen, not even the Lenovo Logo. After 30 seconds, there is a single issue of the computer. Thirty seconds later, the fan turns as if under load, then a bit later, the fan to calm down and the computer will beep again. At this point, I can adjust the brightness of the backlight keyboard, activate the backlight of the screen in and out and the lock LEDs Num Lock shift on the job before, but I can't do anything else.

  I tried to connect an external monitor to see if it's just a screen problem, but it doesn't produce any signal on the screen. Important, the same thing happens also when I try to boot in the BIOS using the Novo or F2 button.

  I discovered that by leaving the computer unplugged with the battery for a long time, I can sometimes get it to display the lenovo logo and then start to boot windows. However, he gets as far as the windows 10 logo then goes black and finally beeps, as shown above. It will not fully start in the operating system. The time it takes between the work is around 5 minutes unplugged for a few hours.

  I tried the stock bios flashing (using a USB bootable BACK player) and eventually managed to Flash the bios, but the problem persists. In the rare cases where the computer starts up, I can get to the bios, but as soon as I reboot, it goes back to the black screen.

  I also tried holding down the power button while up to a minute while the computer is disconnected without battery. This seems to have no effect on the amount of time it takes between two attempts to start succesfull.

  So is - anyone help me? From what I've seen, the problem seems to be deeper than the bios (as evidenced by no change after the flash bios). What I can do about it, or I'm on a laptop?

  I finally diagnosed it as the video card. After I reinstalled windows, the computer starts normally and work, but the video card is turned. No video, blue lines outside the screen. I ordered a replacement motherboard, which is about the only way to fix it if you encounter the same problem that I am. Do not know what started the error if. Could have gotten just old.

• Battery Lenovo Z510 problem

  Greetings! I have a Lenovo Z510 8 GB Ram, Core i7, 1 TB hdd, I bought less than a year ago. Off late I've known major battery issues. He started with the laptop stopping randomly without warning, even if there is a life on the left, for example. PCT of 90 or more. This worsened when the laptop did not start at all, until I plugged in the charger. The only way I can now exploit the laptop is connecting to the charger, but again, the battery remains at 0 of the pct, does not load. The battery light continues to flash red, also, I used a BatteryInfoView application to analyze it, and it still says battery reached 83 percent of its original capacity, however, I get a message every time at startup saying the battery is low and needs to be replaced. What can I do about it? Thank you.

  In response to customer relationships of unexpected problems with the performance of the batteries portable Z500 and Z510, Lenovo made an update of the firmware of battery available via download on the Lenovo Forums.

  This battery firmware is intended to solve unexpected load following symptoms when a Z500 and Z510 mobile phone is turned on:

  • Battery is dead
  
  
  • Battery is not detected
  
  
  • Battery is detected and charged 100%, but when the power is removed, the laptop turns off immediately
  
  
  • When the battery is fully charged and the AC power is removed, the battery level falls considerably less than 10 minutes

  Please note a procedure step by step for the upgrade of the firmware is included in the .zip file, found in the file "ReadMe".

  The battery firmware update can be downloaded here: https://download.lenovo.com/lenovo/content/sm/z500_z510_battery_firmware_update.zip

  Thank you

• Battery - Lenovo Z510

  Hi friends, I have a strange problem. More than a year ago, I bought a Lenovo Z510 which worked well. Unfortunately, just after a year of purchase, the battery started to pose a problem. I talked to the person interested in India who quickly rejected my plea for a new battery. As a result the battery was no charge and rest to 0% power. The service staff tested and concluded that the battery was low and in need of replacement. For all reasons, I haven't bought the new battery. Recently, I was to format my laptop for other reasons, and over time, he began to support up to 100% and has worked for about an hour that was actually fun. But my concern is that the event as to why and how it happens. My other question is that how long it would go. Was it due to formatting and updates! Please throw some light and reason it please. DVKNRao

  In response to customer relationships of unexpected problems with the performance of the batteries portable Z500 and Z510, Lenovo made an update of the firmware of battery available via download on the Lenovo Forums.

  This battery firmware is intended to solve unexpected load following symptoms when a Z500 and Z510 mobile phone is turned on:

  • Battery is dead
  
  
  • Battery is not detected
  
  
  • Battery is detected and charged 100%, but when the power is removed, the laptop turns off immediately
  
  
  • When the battery is fully charged and the AC power is removed, the battery level falls considerably less than 10 minutes

  Please note a procedure step by step for the upgrade of the firmware is included in the .zip file, found in the file "ReadMe".

  The battery firmware update can be downloaded here: https://download.lenovo.com/lenovo/content/sm/z500_z510_battery_firmware_update.zip

  Thank you

• On Win 7 after update itunes Error Message error 7 (Windows error 127) whenever I have start download iTunes

  On Win 7 after update itunes Error Message error 7 (Windows error 127) whenever I have start download iTunes

  HI MikeGeorgen,

  I understand that you have updated iTunes on your Windows 7 computer, but now you see an error when you try to open it. I know it's important to have iTunes working properly, so you can sync your device, so I'm happy to help you.

  Make sure that you logged in as an administrator on your computer, and that you have the latest Windows updates. Then check out the additional troubleshooting steps that are listed here:

  Remove and reinstall iTunes and the components of the software for Windows 7 and later versions

  Thank you for using communities Support from Apple. See you soon!

• After clicking on "Download", nothing happens in Windows 8 - where the 'Run' or 'Start' to install it?

  new computer with Windows 8.
  attempt to download Firefox
  After clicking on "Download", nothing happens in Windows 8 - where the 'Run' or 'Start' to install it?

  Hello lashaw1002, windows 8 is not yet registered as an operating system supported
  https://www.mozilla.org/en-US/firefox.../system-requirements/.
  If you are able to install and run firefox, there will be many problems of stability and other oddities since there are still some integration work required to get firefox on windows 8.

• Windows 7 32 bit does not start after the installation of the need for assistance

  I have an iMac 21.5 inches (mid-2011) with 8 GB Ram, 2 TB SSHD, new HL-DT-ST DVD - RW GA32N and tried to install windows 7 (32 bit) on using Boot Camp Assistant.

  I already downloaded and copied software 4.0.4033.zip Boot Camp here-> https://support.apple.com/kb/DL1630?locale=en_US for my 16 GB Pen Drive MS-DOS (FAT32)

  The installation was successful, and windows 7 loads just fine 1st time, I created UserID and password, settings etc... using the apple keyboard then installed the drivers from apple on this issue of my 16 GB USB key. Seems my Magic Mouse works but my keyboard is not detected

  Then I tried to restart so the changes would come into force, and since then my Windows will not start or run Windows 7

  Now if I start my iMac hold down the Option key, I get Macintosh HDD, windows, recovery 10.11.4 and DVD. If I select Windows or Windows DVD it starts Booting then black screen followed by this Message on the screen «Press a key to boot from the CD or DVD...» »

  If I press any button it starts booting from DVD and gives me the option to install Windows and if I do not press a button some then nothing happens

  Windows does not start a BootCamp HDD and I'm left with no option but to press on the button / stop to stop iMac.

  Fortunately my El Capitan works well, but my Windows will not start. I tried 2 times install windows 7 32 Bit on my BootCamp HDD.

  So any help, I do not understand what am I'm doing wrong, I would be really grateful if someone who knew bootcamp can guide me so that I can run Windows OSX on my iMac.

  Thanks in advance.

  Remove the DVD, boot in OSX and after the release of the following Terminal commands?

  diskutil list

  Cs diskutil list

  sudo TPG - vv - r see the/dev/disk0

  sudo fdisk/dev/disk0

  The "sudo" commands will prompt to enter your password, and there do not appear to come back. You can also see caution against improper use 'sudo' and the potential loss of data due to an "abuse" of the order.

• Windows Update every time that I start it places for no reason

  I have an iMac with bootcamp Windows 7 2007. Whenever I start windows, it says "windows is preparing to install updates". Also the annoying "Restart computer in 15 minutes to complete the updates" window will appear each time too. I have to leave my midnight opened computer during rendering, but whenever I wake him in the morning when I see he has already rebooted and automatically started with the mac partition.

  Even if I can't fix this stupid update, I would like to know how to set windows as default boot drive.

  Thank you.

  Do you have any active Windows automatic updates?

  See also Boot Camp: the operating system default value .

• [Wi - Fi card] Lenovo Z510 list of approved cards

  Which Lenovo brand WiFi cards are approved for laptop Lenovo Z510? I can't whitelist of the BIOS for this model. Any help would be appreciated

  LOL, sorry. You're right, pages 91-92.

  In addition, even if you can find those approved cards FRU, they all only capable BGN. That's why any band of 5 GHz.

  Cheers of "up north, eh!

  DragonRider

• Lenove z510 battery - cannot start the laptop

  Hi all

  I bought a lenovo z510 7 months ago. It was working fine. Suddenly, battery does not charge while the AC adapter is connected. Then, she fell to zero, and now I can't open. It recharges even now.

  I tried to uninstall the ACIP, the energy Manager,...; However, it did not work.

  I would appreciate your help.

  Kind regards

  Maha

  In response to customer relationships of unexpected problems with the performance of the batteries portable Z500 and Z510, Lenovo made an update of the firmware of battery available via download on the Lenovo Forums.

  This battery firmware is intended to solve unexpected load following symptoms when a Z500 and Z510 mobile phone is turned on:

  • Battery is dead
  
  
  • Battery is not detected
  
  
  • Battery is detected and charged 100%, but when the power is removed, the laptop turns off immediately
  
  
  • When the battery is fully charged and the AC power is removed, the battery level falls considerably less than 10 minutes

  Please note a procedure step by step for the upgrade of the firmware is included in the .zip file, found in the file "ReadMe".

  The battery firmware update can be downloaded here: https://download.lenovo.com/lenovo/content/sm/z500_z510_battery_firmware_update.zip

  Thank you

• Halo 2 for windows vista does not work on my windows 7. Saiys it cannot start the direct customer

  original title: Halo 2 for windows vista

  Halo 2 for windows vista does not work on my windows 7.  Saiys it cannot start the direct customer.  It will not work in single user either...

  Hello

  Plase make sure you have the latest version of the GFWL Client installed:

  http://www.Microsoft.com/games/en-us/live/pages/livemarketplace.aspx

• I have an old computer running windows 98 when I try to start until you get a date checking DMI Pool error message failure boot ATAPI CD-Rom 07,08 what this mean and how can I solve this problem?

  I have an old computer running windows 98 when I try to start until you get a date checking DMI Pool error message failure boot ATAPI CD-Rom 07,08 what this mean and how can I solve this problem?

  I want to erase the hard drive and use it to install windows xp.

  From what I've read, it could be a number of things that went on the wall. Issue of dead hard drive, BIOS, peripheral USB plugged when starting, etc.

  Does not help, but could help to point you in the right direction...

• Windows firewall stops every time I start my computer.

  OT: I have to pass Windows Firewall, every time I start my computer. What is this caused by a virus or a bad setting in Windows?
  Whenever I turn on my computer, I check that the Windows Firewall is enabled. It is still off and I have to turn it on.

  Hi Tony McLaughlin,.

  1. what operating system is installed on the computer?
  2. are you aware of any hardware or software changes, prior to the beginning of the question?
  3. you have any third-party firewall installed on the computer?

  Method 1
  The Windows Firewall will close if you have any third-party firewall is running on the computer. I suggest you try the steps from the following link:

  Windows Firewall is turned off every time I start my computer
  http://TechNet.Microsoft.com/en-us/library/cc749262 (v = ws.10) .aspx

  Method 2
  To start the Windows Firewall service.
  a. Click Start and all programs and type services.msc in the run window and press ENTER.
  b. find Windows Firewall services and put him automatically and rstart services and verification.

  Additional information:
  Security Warning: the Windows Firewall is disabled
  http://support.Microsoft.com/kb/2288085

• Windows Live Mail could not be started because msmail.dll could not be loaded. What should I do?

  Start Windows Live Mail

  Windows Live Mail could not be started because msmail.dll could not be loaded.  What should I do?

  Post Windows Live questions in the appropriate forum found here:
  http://windowslivehelp.com/