Windows XP Cd-rom problems, code 19 error__

Similar Questions

• My sata cd rom a problem after re-installation of WinXP Pro by this cd rom; error code 041; How do I solve this problem

  My sata cd rom a problem after re-installation of WinXP Pro by this cd rom; error code 041; How do I solve this problem

  It's almost certainly a driver problem.

  Please tell the service pack on your Windows® XP Pro level forum and the manufacturer and model of your system, if it is conditioned, or the make and model of your motherboard if it is not.  In addition, please tell us the manufacturer and model of the optical drive.

  First of all, if there is a system, go to the support Web site of the manufacturer for your system model.  If this is not a system, go to the support Web site of the manufacturer of the motherboard for your model of motherboard.  In the first case, you should find the drivers, chipset in particular drivers, updates and software for your system. Install all the that apply.  In the second case, you will find the drivers of integrated devices, chipset, updates and software for your motherboard drivers. Yet once, install all the that apply.  As we know nothing on the optical drive other it is attached via SATA, I can't talk about what to do there except that you should go to the manufacturer's support Web site and search for drivers and updated firmware for your model.

  It would have been helpful if you had provided more complete information on the installation of Windows, your system hardware and the optical drive.  The most complete information; more answers you will get.  Please, read:KB555375 - how to ask a question.

  Don't forget, no member of this forum is omniscient.

• The CD-ROM/DVD-ROM driver cannot be loaded by Windows and can be corrupted (Code 39).

  My DVD/CD driver drive HL-DT-ST DVDRAM GSA-T20N ATA Device cannot be loaded by Windows and can be corrupted (Code 39). How can I get the original device installed new driver if the CD/DVD drive does not work? It is available for download? Should it be first uninstalled and re - installed? A relative novice can handle?

  Hello

  Have you made changes on the computer before this problem?

  I would suggest trying the following methods and check if it helps.

  Method 1:

  Update the driver for the CD/DVD drive and check if that helps.

  Updated a hardware driver that is not working properly:
  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  Method 2:

  Run the fixit for the following Microsoft Fixit and if it helps.

  Your CD or DVD drive cannot read or write media:

  http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us

  Method 3:

  Uninstall and reinstall the CD/DVD driver and check if it helps.

  Follow the steps to uninstall and re-install the drivers.

  a. click on start toreduce this includes this im and then click Control Panel.

  b. click system and Maintenance, click Systemand then click on Device Manager.
  Note If Control Panel is in Classic view, double-click System, and then click Device Manager.

  Reduce this includes this imageIf you are prompted for an administrator password or a confirmation, type the password, or click allow.

  c. in the Manager device, expand CD-ROM/DVD-ROM drives, right click on CD and DVD devices and then click Uninstall.

  d. When you are prompted to confirm that you want to remove the device, click OK.

  e. restart the computer.

  Hope the information is useful.

• Windows Update has stopped working and Windows has stopped the unit, he reported problems (code 43)

  Original title: Windows Update stopped working Vista Home Basic.

  HP laptop 550 Vista home basic 32-bit.  Windows Update stopped working, also adapter display Windows stopped the device says it has reported problems (code 43). I uninstalled / reinstalled the drivers, but not make any difference. Thanks for any help.

  Hello

  Question: Windows Update has stopped working

  1. do you get an error message when you try to update?

  2. were there any changes (hardware or software) to the computer before the show?

  Perform the steps from the link below.

  The problems with the installation of updates (Windows Vista)

  Question: display Error Code 43 adapter has stopped the unit

  Run the Fixit and check if it helps.

  Hardware devices do not work or are not detected in Windows (Fixit)

  Hope this information helps.

• Error "Windows has stopped this device because it has reported problems (code 43)" after the computer start in low resolution and remains after the connection

  Original title:

  Problem occurs intermittently, but almost every time at the first start the morning. The problem can be seen during the POST and the rest after logon. After several reboots, he can come good, but at the next restart could be bad. One clue is that the Device Manager said that to display card NVIDIA Ge Force 8400 GS that "Windows has stopped this device because it has reported problems (code 43)." Driver update says I have the latest driver insalled, version 8.17.12.9573. Help, please

  Have you tried to update your BIOS? Are there updates the firmware for your video card?

• Windows was able to successfully install device driver software, but the driver has encountered a problem when he tried to run. The problem code is 43.

  Windows was able to successfully install device driver software, but the driver has encountered a problem when he tried to run. The problem code is 43.

  Signature of the problem:
  Problem event name: PnPDeviceProblemCode
  Architecture: x 86
  Hardware ID: PCI\VEN_10DE & DEV_0428 & SUBSYS_110B1734 & REV_A1
  Configure the class GUID: {4d36e968-e325-11ce-bfc1-08002be10318}
  PnP problem code: 0000002B
  Driver name: nvlddmkm.sys
  Driver version: 8.17.13.142
  Driver date: 15/05/2012
  OS version: 6.0.6001.2.1.0.768.2
  Locale ID: 1033

  Hi, Senga,

  Start > right click on computer

  Select manage

  Click on continue in the UAC window

  Click on Device Manager

  Click on the + sign next to the device

  Right click on driver and select rollback

  If the cancellation is dimmed, select uninstall

  Close Device Manager

  Back to zero computer and Windows will reinstall the driver

  Go to the manufacturer website, download the updated driver to update and save it to the desktop

  Double-click the .exe file to install

  You can also try booting in safe mode with network.  Download the following tool and run a scan complete to rule out malware.

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=16

• I can't activate Windows 7, when I insert the product note key, which is an error 0xC004F063 problem code. What do I do?

  I can't activate Windows 7, when I insert the product note key, which is an error 0xC004F063 problem code. What do I do?

  Boost telephone:

  Activate Windows 7 manually:

  1. click on start and in the search for box type: slui.exe 4

  2. press enter on your keyboard

  3. Select your country.

  4. Select the telephone activation option and brace yourself for a real person.

  This is the Forum for Windows Update.

  You will get the best help for any problem of activation in Windows 7 install, upgrade and activate Forum. the link below:

  http://social.answers.Microsoft.com/forums/en-us/w7install/threads>

  UTC/GMT is 23:41 Friday, January 20, 2012

• Unknown device: Windows has stopped this device because it has reported problems (Code 43).

  I have Windows 7 Ultimate. Recently an unknown device keeps popping up in the device manager every time that I start to win. It is reported the location is in the front USB hub, but I haven't changed it anything lately. The device status says "Windows has stopped this device because it has reported problems (Code 43)". I can uninstall or disable it but it will get picked up again the next time that I reboot. All other usb devices (mouse, keyboard, webcam, UPS APC, external hard drive, printer) work very well. How can I get rid of this nuisance so that it is not reappear?

  If the problem coincided with connecting the inverter APC that may indicate the problem is with the inverter.

  Somewhat similar situation discussed in the following link:

  http://www.velocityreviews.com/forums/t527369-APC-ups-USB-as-unknown-device.html

  Your situation sounds similar as "Information system" leading the 'problem of the device' has an error Code "this device is working properly" but still "unknown device".

  I would say to detach from the APC UPS of the computer and uninstall any software related.

  Restart the computer and see if the "Unknown device" problem resolves.

• State of the device, Windows stopped the device because it has reported problems (Code 43)

  A usb driver for microsoft

  Windows has stopped the device because it has reported problems (Code 43) Standard USB HOST Controller, location of port #0002 Hub_ #0005

  Right click on desktop, select Properties.  On the next page, top left click on Device Manager.

  Scroll down the page until you come to the Universal Serial Bus Controllers and double click on this.

  Uninstall ALL USB host controllers. (Remember that when you have finished the last of them, your keyboard and mouse may not work!)  Restart the PC.  Windows should then pick up the controllers & install the correct drivers.  The only time where it will not install the drivers is when the USB host controllers are physically damaged.  In this case, the fastest and cheapest method is to buy a USB PCI card which fits directly into a PCI slot on your motherboard and will come with three or four USB 2.0 ports.

• "Window could not find updates. Error (s) found: Code 80244018. Update the window has encountered a problem.

  Hello!

  I found the error in my system, "window 8.

  The message that is displayed when the search for updates,

  "Window could not find updates. Error (s) found: Code 80244018. Upgrade from window fell on a problem".

  To get help on this error, no feedback is provided by help and support section as well.

  Please help me solve this problem

  Concerning

  Generally attributed to a proxy server or a firewall.

  See the info here:

  http://answers.Microsoft.com/en-us/Office/Forum/officeversion_other-OneNote/i-cant-install-one-note-app-for-surface-RT-error/4737171e-6fce-48f6-88d1-8c44ac0e6ae0

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-windows_store/cannot-upgrade-to-Windows-81-error-0x80244018/56c64112-d374-40Cf-B1B1-8c4fd4924d69

  Discussion:

  http://social.msdn.Microsoft.com/forums/en-us/a8c813ab-5b18-482C-82c4-12f1cc57b460/what-issue-is-attributed-to-error-code-0x80244018

• Windows was able to successfully install device driver software, but the driver has encountered a problem when he tried to run. The problem code is 39. __

  The cdrom did run for awhile... and then he stopped. I googled the error code and it said: ERROR_HANDLE_DISK_FULL
  39 (0 x

  Problem event name: PnPDeviceProblemCode
  Architecture: x 64
  Hardware ID: SCSI\CdRomHL-DT-STDVDRAM_GH15F___EG00
  Configure the class GUID: {4d36e965-e325-11ce-bfc1-08002be10318}
  The PnP problem code: 00000027
  Driver name: cdrom.sys
  Driver version: 6.0.6002.18005
  Driver date: 11/04/2009
  The system version: 6.0.6002.2.2.0.768.3
  Locale ID: 4105

  Is there a way to reset the device?

  Thank you... Steve

  Hi Steve,.

  Here's an article that might help: http://support.microsoft.com/kb/314060

  Method One

  1. Completely remove the Upperfilters and Lowerfilters from the following registry key values:
     HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

     NOTE: If you get a code 39 message, it may be that additional third-party filter drivers were added to UpperFilters and LowerFilters values in addition to Adaptec filter drivers. In this case, you can try to remove the first non-Adaptec filter drivers, filters Easy Creator by leaving in place to see if the Code 39 goes away. If you still receive an error code 39, 32 or 31, delete Upperfilters and Lowerfilters completely values in the previous key.

  Mark <> Microsoft Partner

• 19 CD rom error code... computer does not recognize, etc...

  19 CD rom error code... computer does not recognize, etc...

  I tried troubleshooting and I get "unable to set of troubleshooting."
  Please let me know if someone has a possible solution.  I am running Windows 7 family and probably a 5 on the computer.
  Thank you
  JDub

  Hey JDub,

  Please contact Microsoft Community Forum!

  This issue would have occurred after you installed, uninstalled or updated a program or Windows.

  19 code means there is a driver conflict such as two devices attempt to use the same resources.
  
  

  When you say "unable to set Troubleshooting" what Troubleshooter you are referring to?

  You can try the steps from the following link and check:

  Registry warning: Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base. How to back up and restore the in the Windows registry: http://windows.microsoft.com/en-us/windows7/Back-up-the-registry

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/314060

  Keep us updated on the State of the question

  Using the windows-related issues feel free to post on the Microsoft Community Forum!

• Satellite L305D-S5892 - Windows has encountered a problem

  Hello

  I have an I have a Toshiba-L305D-S5892
  With Vista Home Prem 32

  I have a few problems and am currently blocked.

  Each problem below, is a problem that I met after taking a few steps.

  * The 1st problem *.

  A few hours ago my screen was frozen just after I tried to install this codec from microsoft, so the only option I had was to do a hard reset.
  When my computer back on, I received this message:

  Windows has encountered a problem communicating with a device connected to your computer.

  This error may be cause of disconnect a device removable storage such as an usb external drive while the appliance is in use or by defective as a hard disk hardware or the CD-ROM drive which is a failure. Make sure that all removable storage is properly connected, and then restart your computer.

  If you continue to receive this error message, contact the manufacturer of the equipment.

  File: \Windows\system32\winload.exe

  Status: 0xc00000e9

  Info: An unexpected I / 0 error has occurred.

  I didn't have any usb device or removable in media.
  I can only access my utility series at the beginning, which is this menu: hand-Advanced-display-security-Boot - out

  * 2nd problem *.

  I opened my laptop and released the CD / DVD + RW, he started upward and now I get this message:

  For Realtek RTL8101E/8102E PCI - E Ethernet Controller v1.07

  PXE - E61: Media test failure, check cable.

  PXE - M0F: Exit PXE ROM.

  No boot device - insert boot disk and press any key

  * 3rd problem *.

  I downloaded the NEOSMART repair Cd.

  Once I'm in the System Recovery Options, it tells me to select an operating system. However it has not traded. If I press drivers to load, then a message tells me to insert the media, and then select drivers. I almost 'ok', and then am taken to explore, when there are a few system files and files (all empty)?

  I'm confused... any help?

  Hello

  For me, it looks like a problem with the system eventually installed the HDD failures.
  Why?

  Due to the issue described in point 2.
  PXE - E61: Media test failure, check cable error is displayed because the phone didn t find the installed operating system and try to boot from LAN.
  This happens especially if the HARD drive was not recognized by the BIOS.

  My recommendation;
  Access the BIOS and check if the HARD drive is listed there.
  If this isn't the case, then you will need to replace the HARD drive and reinstall the operating system.

  If the HARD drive is listed in the BIOS, then take a recovery disk and try to reinstall the OS again.
  If you have no recovery disc, then you can order it here.
  (I guess it's a Toshiba laptop model we)
  https://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/serviceUnitVerification.jsp?orderType=SFF

  Good luck

• Driver for old parallel port; This device has a problem: Code = 28 (0x1C)

  We organize a Dos based Windows 98 application and I need to find a driver for the integrated parallel port. The motherboard is an ASUS P5GD2-TMX/S. Both the local provider and ASUS only provide XP and more drivers for the motherboard. How can I determine the manufacturer of the parallel port and download the driver directly from their site? I done this before for the serial port and downloaded and installed a Sunnix driver, which worked.

  I did some research on the North Bridge, South bridge and the Super i/o chip set, but to no avail. Here is a copy of the output of sysinfo32.

  [Peripheral problem]

  Unknown device
  Unknown
  This device has a problem: Code = 28 (0x1C)
  The drivers for this device are not installed correctly. To install the driver
  for this device, click the driver tab, then click on set to update driver.
  The registry key: HKEY_LOCAL_MACHINE\enum\ACPI\ * INT0800\0
  Alloc resources: logical Configuration 0
  Memory address range: Base = xFFB80000 End = xFFBFFFFF
  Forced resources: None
  Start resources: logical Configuration 0
  Memory address range: Base = xFFB80000 End = xFFBFFFFF
  Filtered resources: None
  Core resources: logical Configuration 0
  Memory address range: Base = 00000000 00000000 Min End = x x = xFFB80000 Max = xFFBFFFFF
  Driver: Driver is not installed

  Standard 101/102-key or Microsoft Natural Keyboard
  Keyboard
  This device has a problem: Code = 27 (0x1B)
  System failure: try changing the driver for this device. If this does not work,
  see the documentation for your hardware.
  The registry key: HKEY_LOCAL_MACHINE\enum\ACPI\ * PNP0303\0
  Alloc resources: None
  Forced resources: None
  Start resources: no
  Filtered resources: logical Configuration 0
  IRQ: mask 0: x 0002
  IO range: Base = x 0000 End = 0000 Min = Max = x Alias 0060-0060 x x = x 00, decode = x 00
  Base = x 0000 End = 0000 Min = Max = x Alias 0064-0064 x x = x 00, decode = x 00
  Core resources: logical Configuration 0
  IRQ: mask 0: x 0002
  IO range: Base = x 0000 End = 0000 Min = Max = x Alias 0060-0060 x x = x 00, decode = x 00
  Base = x 0000 End = 0000 Min = Max = x Alias 0064-0064 x x = x 00, decode = x 00
  Driver: Keyboard\0003
  Driver date: 23/04/1999
  Driver: idvkd.sys
  File size: driver not installed
  File date: driver not installed
  Driver: hidparse.sys
  File size: 44368 (0xAD50)
  File date: 23/04/1999-22:22
  Legal name: Microsoft Corporation
  File version: 4.10.2222
  Driver: hidclass.sys
  File size: 23520 (0x5BE0)
  File date: 23/04/1999-22:22
  Legal name: Microsoft Corporation
  File version: 4.10.2222
  Driver: hidvkd.sys
  File size: 5088 (0x13E0)
  File date: 23/04/1999-22:22
  Legal name: Microsoft Corporation
  File version: 4.10.1998

  PCI card
  Unknown
  This device has a problem: Code = 28 (0x1C)
  The drivers for this device are not installed correctly. To install the driver
  for this device, click the driver tab, then click on set to update driver.
  The registry key: HKEY_LOCAL_MACHINE\enum\PCI\VEN_8086 & DEV_2668 & SUBSYS_81A71043 & REV_04\BUS_00 & DEV_1B & FUNC_00
  Alloc resources: logical Configuration 0
  Memory address range: Base = xD20C0000 End = xD20C3FFF minutes = x 00000000 Max = xFFFFFFFF
  Forced resources: None
  Start resources: logical Configuration 0
  Memory address range: Base = xD20C0000 End = xD20C3FFF minutes = x 00000000 Max = xFFFFFFFF
  Filtered resources: None
  Core resources: logical Configuration 0
  IRQ: mask 0: xFFFF
  Memory address range: Base = xD20C0000 End = xD20C3FFF minutes = x 00000000 Max = xFFFFFFFF
  HW revision: 004
  Driver: Driver is not installed

  Universal Serial Bus PCI
  Unknown
  This device has a problem: Code = 28 (0x1C)
  The drivers for this device are not installed correctly. To install the driver
  for this device, click the driver tab, then click on set to update driver.
  The registry key: HKEY_LOCAL_MACHINE\enum\PCI\VEN_8086 & DEV_265C & SUBSYS_265C1043 & REV_04\BUS_00 & DEV_1D & FUNC_07
  Alloc resources: logical Configuration 0
  Memory address range: Base = xD20C4000 End = xD20C43FF minutes = x 00000000 Max = xFFFFFFFF
  Forced resources: None
  Start resources: logical Configuration 0
  Memory address range: Base = xD20C4000 End = xD20C43FF minutes = x 00000000 Max = xFFFFFFFF
  Filtered resources: None
  Core resources: logical Configuration 0
  IRQ: mask 0: xFFFF
  Memory address range: Base = xD20C4000 End = xD20C43FF minutes = x 00000000 Max = xFFFFFFFF
  HW revision: 004
  Driver: Driver is not installed

  PCI system management bus
  Unknown
  This device has a problem: Code = 28 (0x1C)
  The drivers for this device are not installed correctly. To install the driver
  for this device, click the driver tab, then click on set to update driver.
  The registry key: HKEY_LOCAL_MACHINE\enum\PCI\VEN_8086 & DEV_266A & SUBSYS_266A1043 & REV_04\BUS_00 & DEV_1F & FUNC_03
  Alloc resources: logical Configuration 0
  IO range: Base = x End = x051F minutes = x 0500 0000 Max = xFFFF Alias = xFF, Decode = x 00
  Forced resources: None
  Start resources: logical Configuration 0
  IO range: Base = x End = x051F minutes = x 0500 0000 Max = xFFFF Alias = xFF, Decode = x 00
  Filtered resources: None
  Core resources: logical Configuration 0
  IRQ: mask 0: xFFFF
  IO range: Base = x End = x051F minutes = x 0500 0000 Max = xFFFF Alias = xFF, Decode = x 00
  HW revision: 004
  Driver: Driver is not installed

  The motherboard seems to be Intel 915P chipset.

  Don't know if it will help, but try installing the software Intel(r) utility V6.0.1.1002 of Installation for Windows 2000/XP/2003 (under Win2K - others) for P5GD2 motherboard from the following link that appears in support of Windows 98 Second edition:

  http://www.ASUS.com/motherboards/P5GD2/HelpDesk_Download/

  Then restart the computer.

• When the phone rings it temporarily blocks access to internet on my laptop. I ran "Troubleshooting" and he said the teredo tunneling adapter microsoft has a driver problem (code 10)

  Teredo tunneling adapter error: Code 10

  I have a wireless modem in my house.  When the phone rings it temporarily blocks access to internet on my laptop. I ran "Troubleshooting" and he said the teredo tunneling adapter microsoft has a driver problem (code 10) and I have to click "Reinstall driver" I did.  But it will not re - install.  I'm not too irritable.   Can help you.

  In addition, I don't know if there is a related problem, but my laptop takes a long time to communicate with the printer.   The doc will be in Quebec but does not print.

  Thank you.

  Hi LindaGreenwood,

  1. what operating system is installed on the computer?
  2. you have made no changes to the computer before the broadcast took place?

  Generated 10 error code when Device Manager does not have enough information or error that spread upwards by device drivers is not recognized by Device Manager. In addition, this error may occur if one of the pilots who needs the unit does not start. If multiple drivers are used by a particular device, it can be difficult to determine which failed.

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers
  http://support.Microsoft.com/kb/943104

  I suggest you uninstall the drivers completely uninstall and then reinstall the drivers from the manufacturers Web site.

  Updated a hardware driver that is not working properly
  http://Windows.Microsoft.com/en-in/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly