Wireless authentication but encryption

Similar Questions

• What does "wireless authentication failed because of a time-out" mean?

  Have a combo unit router and modem.  Having two computers.  You can use the wireless that the other cannot use Wired.  Getting messages like "wireless authentication failed because of a time-out," conflict of IP address and canceled due to the delay.  There was a variety of messages.  We had been able to use a router before, but it would be turned off every two hours or more.  Giving the same messages on Windows Vista.  The other computer is Windows XP Motorola
  modem/router.

  Hello

  1. what security WEP, WPA, etc. Do you use?
  2. is the driver software updated for the router to work correctly on Vista computer?

  I suggest you to follow these steps and check if that helps:

  Method 1:
  I suggest you to check if you can connect by using a different port or a different router in case the problem is with the router itself.

  Method 2:
  You can also visit the link provided below, which offers a similar problem resolution. Check if the steps to help you resolve the problem.
  http://social.answers.Microsoft.com/forums/en-us/vistanetworking/thread/4db4caa0-86bb-4b7b-8aa7-252d5653f063

  It will be useful.

• Vista can communicate with the wireless router, but cannot access the internet

  I have a SONY Vaio with Vista.  Until recently, it worked fine with an old router Netgear wireless with no encryption.  I replaced the router with a Linksys E1200 and set up for WPA/WPA2 encryption.  My iPod, iPad, an HP printer and laptop running Windows 7 quite change with absolutely no problem.  After entering the SSID and password on the Vaio, it connects to the router but will not access the Internet.  I tried to reset the router and cable modem, without success.  Suggestions before you start the laptop across the room and rid my life of the bane of Vista forever?

  Hello

  ·         What is the antivirus installed on the computer program?

  Let's try the following methods.

  Method 1: Temporarily disable the antivirus on the computer program and check if the problem persists. If no problem occurs, then you need to firewall settings in the security software.

  Note:  Check that you activate your anti-virus protection on the computer back after you complete these steps. It is not recommended to disable these settings on the computer. It's just to solve the problem.

  Disable the anti-virus software

  Method 2: Follow the steps in the article mentioned below.

  In the Windows wireless network connection problems

• Need to disable CGI, I have two-factor authentication, but I don't have the phone number or device with me. What can I do?

  Need to disable CGI, I have two-factor authentication, but I don't have the phone number or device with me. What can I do?

  For Apple ID - Apple Support two-factor authentication

  If I can not connect, how I again to access my account?

  If you can't sign in, reset your password, or receive verification codes, you can account recovery application to restore access to your account. Account recovery is an automatic process designed to help you back into your account as soon as possible while denying access to anyone who might be impersonating you. It may take a few days - or more - depending on the specific account information, you provide to verify your identity.

  It will be your option. If you try to find an iPhone with locking Activation that you don't remember the password, you can remove the account from the iPhone with the help of Apple's Support with the receipt of the initial purchase of the iPhone as a way to prove that you are the real owner of this iPhone.

• Wireless connected but cannot display Web page

  Hi, I have a HPG7094 laptop with Vista 64 bit installed.

  I tried for days to fix my problem. My wireless connection has stopped working. It says it is connected to my wireless - excellent - but when I try to open the internet I get the error IE cannot open the Web page. I deleted my network and tried to re-login only to get the same error. I did a clean install on my laptop and downloaded the drivers on the HP site, but it's always the same.

  In the lower RH it says 'Unidentified network' (and the name of my network) access: Local only. If I connect the ethernet cable, it works fine and if I connect my mobile dongle orange it works very well.

  I have other laptops and desktop computers and all these connect wirelessly without problem. I have tried to 'fix' the wireless connection and not to renew the period of INQUIRY, still no joy. I connected on the router from my office and changed the channel from "auto" to "6" and "11", but this has no effect.

  Someone at - it ideas, what could cause this problem, any help would be highly appreciated.

  Gail

  Hello

  After a couple of hours last night looking through this forum, I came across a post by Paul Tikkanen, January 21, with a link to another driver for the Atheros wireless. I downloaded and now my wireless works!

  Thank you for all your help and keep up the good work!

  Gail

• I have the wireless option, but if I use it not I can't connect to the internet.

  I have the wireless option, but if I use it not I can't connect to the internet.

  original title: difficulty borrowed from internet

  If it's the Acer utility, it is best to visit Acer support:

  http://support.Acer.com/us/en/default.aspx

• My PC is connected to the wireless network, but it is impossible to open any internet page. I went through the diagnosis of Internet Explorer, see below.

  Diagnosis of last run time: 28/01/12 10:16:32 Gateway diagnosis

  Entry door

  Info the following proxy configuration is used by IE: automatically detect settings: enabled Automatic Configuration Script: Proxy Server: Proxy bypass list:

  info could not get the proxy settings via the Proxy Automatic Configuration mechanism

  Info this computer has the following (s) default gateway: 0.0.0.0

  warn that there is no default gateway entry

  repair automatic action: reset the network connection

  action to disable the network card

  activation of the card network action

  successfully activated information network adapter

  Info this computer has the following (s) default gateway: 0.0.0.0

  warn that there is no default gateway entry

  user redirection of information in support of the appeal

  IP layer diagnostic

  Corrupted IP routing table

  prevent the default route is missing or not valid

  Invalid entries in the ARP cache

  action cache ARP has been emptied

  Diagnosis of IP Configuration

  Invalid IP address

  detected info valid IP address: 192.168.0.1

  Wireless diagnosis

  Wireless - Service disabled

  Wireless - user SSID

  required user input action: specify the name of the network or the SSID

  Wireless - first installation

  Info the name of the wireless network (SSID) to which the user wants to connect is IrinaLaptop-router.

  Wireless - Radio

  detected info valid IP address: 192.168.0.1

  Wireless - off limits

  Wireless - hardware problem

  Wireless - Novice user

  Wireless - network Ad - hoc

  Wireless - less preferred

  Wireless - 802. 1 active x

  Wireless - Configuration mismatch

  Wireless - low SNR

  WinSock diagnostic

  WinSock status

  info all base service provider entries are present in the Winsock Catalog.

  channels of information the Winsock Service provider are valid.

  Info entry provider MSAFD Tcpip [TCP/IP] passed the loopback communication test.

  Info entry provider MSAFD Tcpip [UDP/IP] passed the loopback communication test.

  Info entry RSVP UDP Service Provider provider passed the loopback communication test.

  Info entry RSVP TCP Service Provider provider passed the loopback communication test.

  Info connectivity is valid for all Winsock service providers.

  Diagnosis of network adapter

  Network location detection

  Info to help home Internet connection

  Identification of network adapter

  Info network connection: name = connection to the LAN, device = Broadcom 440 x 10/100 Integrated Controller, MediaType = LAN, type = LAN

  Info network connection: name = wireless network connection, Device = Intel (R) PRO/Wireless 3945ABG Network Connection, MediaType = LAN, type = Wireless

  Info network connection: name = 1394 connection, device = 1394 Net Adapter, MediaType = LAN, type = 1394

  Info network connection: name = connection high speed, device = Miniport WAN (PPPOE), MediaType = PPPOE, type = NONE

  Info network connection: name = blank, peripheral = Miniport WAN (PPPOE), MediaType = PPPOE, type = NONE

  Info both Ethernet connections and wireless available, ask the user for selection

  required user input action: select network connection

  Info Wireless connection selected

  State of the network adapter

  Info network connection status: connected

  HTTP, HTTPS, FTP Diagnostic

  HTTP, HTTPS, FTP connectivity

  warn HTTP: error 12007 connecting to www.microsoft.com: the server name or address cannot be resolved

  warn HTTP: error 12007 connecting to www.hotmail.com: the server name or address cannot be resolved

  WARN HTTPS: error 12007 connecting to www.microsoft.com: the server name or address cannot be resolved

  WARN HTTPS: error 12007 connecting to www.passport.net: the server name or address cannot be resolved

  WARN FTP (passive): error 12007 connecting to FTP.Microsoft.com: the server name or address cannot be resolved

  WARN FTP (active): error 12007 connecting to FTP.Microsoft.com: the server name or address cannot be resolved

  error could not make an HTTP connection.

  error could not make an HTTPS connection.

  error could not make an FTP connection.

  I did not want to do this (restore point). However, I found a solution. It comes: http://forums.techguy.org/networking/1029348-network-connection-status-media-disconnected.html

  Where there are two crucial steps (do not know if the two were needed) RUN command (1) netsh int ip reset reset.log and (2) netsh winsock reset catalog
  
  
  After a restart, hey presto my wireless connection was repaired. This seems useful, but not essential (shows wireless performance but not the solution): http://wpc.475a.edgecastcdn.net/0047...etup.1.2.0.exe which is run Xirrus Wi-Fi Inspector 
  Thanks for your time!
  Good bye

• My computer connects to the wireless internet, but I am still unable to connect to internet even though it is always connected to the wireless connection.

  connection Wi - Fi

  My computer connects to the wireless internet, but I am still unable to connect to internet even though it is always connected to the wireless connection. How can I solve this problem and what could be the problem?

  Hello

  1 did you change your computer, after which the issue started?
  2. during how long have you had the problem?
  3. what web browser do you use?

  I recommend to update your network card drivers and check if that helps.
  http://support.Microsoft.com/kb/283658

  Let us know the status of the issue and also please answer these questions.

• I have a dell laptop with windows XP I want to use a wireless mouse but cannot figure out how to turn off the pc mouse

  I have a dell laptop with windows xp I want to use a wireless mouse but cannot understand how to turn off the pc mouse

  Thank you for your help, I saved it for future use. My computer it turns out that's very smart after all the fourth test of every thing, I turned it on and the mouse remotely worked, thanks again

• HP LaserJet 200 colorMFP M276nw connects to my wireless network, but will not recognize the printer

  I am trying to set up my wireless printer, and the printer says its is connected to my wireless network, but I can't get my computer to print wireless if I disconnect my regular network and attach the direct wireless network name, which is different and stops my internet to work. How can I get my computer to recognize the printer on my regular wireless network?

  Hi @lelg,

  I understand that you want to configure the printer on the wireless network. I can help you with this.

  Uninstall the printer software.

  Uninstalling the printer software.

  Restore the default settings of the printer.

  Go to Configuration, restore the default values.

  Cycle power to the router and the computer.

  Run the installer on the printer wireless.

  Go to the configuration, Setup, menu wireless network, Wireless Setup Wizard.

  Print a configuration page to get the IP address of the printer.

  Print a Configuration report.

  Select the method.

  If you have a valid IP address for the printer, then try and access the Web built-in to the printer server. Type the IP address in the address bar of your web browser. (Internet Explorer)

  If it loads the page from the network printer then the printer is on the network.

  Download, save, and then run the installation of the software. Color HP LaserJet Pro 200 pilot M276nw MFPS.

  Select your operating system, click Next and click on the software to download and install.

  Test the printer.

  What operating system do you use? How to find the Windows Edition and the Version on your computer.

  Please provide detailed results if you're still having problems.

  Good day!
  Thank you.

• I accidentally turn off my WIFI! When I go to it says disable 'status' HP wireless assistant but no, where do see how to activate it again, can someone help please!

  hen I go to it says disable 'status' HP wireless assistant but no, where do not see how to activate it again, can someone help please!

  I went to something help I have and it says to reboot my laptop, press F10, then go to system configuration > integrated device options > LAN/WLAN switching > activate. I restarted my laptop and pressed F10 but it come with the system configuration...

  Hi you can access device manager and enable you WLAN, or simply more portable computers HP come with a button to toggle WLAN, please check the color of the light wireless button and press again to see if it changes color, if not you have successfully activated the WLAN again.

  You can also try

  1. Reboot the laptop.
  2. Press F10 .
  3. Enter the BIOS .
  4. Select Advanced options .
  5. Select the Device option , WLAN/LAN switching.
  6. Switch to Activate .
  7. Select save changes and exit .

  If you could tell the laptop model and the version of the operating system you use that I'll be able to give you more accurate and simpler measures

• I can delete, change and move all other profiles wireless network but one that reappears immediately after that I erase it.

  I have exactly the same problem in Windows Vista Ultimate Edition.  I can delete, change and move all other profiles wireless network but one that reappears immediately after that I erase it.

  I see that you asked initially that this issue in 2010.  Has there every been a resolution?
  Elliott
  Split of: http://answers.microsoft.com/en-us/windows/forum/windows_7-networking/network-profile-keeps-reappearing-and-displacing/515108df-1aa6-457f-9262-6be835f82198

  My Eureka has been using netsh, explains Superuser.com «How to completely remove a wireless network from Vista» Everything I found on the Microsoft site doesn't give any examples on how to find profiles (netsh wlan name) or the statement appropriate to remove this profile (netsh wlan dlete name = "the name exactly as shown, case-sensitive quotes". That he solved it for me.

• I can connect to my wireless router, but cannot get internet connectivity via Wireless. If I connect the cable to the port on the router, I get internet connectivity.

  Wireless router / Internet problems

  I am running Windows Vista Home Edition with Security Essentials.  I can connect to my wireless router, but cannot get internet connectivity via Wireless.  If I connect the cable to the port on the router, I get internet connectivity.  Is there a firewall setting that could cause this problem?

  Hello

  Your router could be suspicious here, you have successfully updated its firmware as a possible solution? And I would like to
  Update your WiFi drivers on computers. How you are positioned in the router? Are there
  obstacles in the path?

  Actually try updating your driver and disabling the network logon.

  Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
  version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
  Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
  manufacturer of system become your backup policies).

  Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
  updated drivers.

  I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
  are almost always old, and you can search drivers manually as needed.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ------------------------------------------------------

  Make sure you know the details of connection to your wireless router - SSID and password.

  You lose connection when you do and have to redo your logon.

  Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
  lower left click on merge or delete network locations - REMOVE all instances of your network (and the
  others you don't use anymore) - REBOOT. Start - Connect To log on to the network.

  -----------------------------------------------------

  Check this box:

  Strange problem with Internet under Vista
  http://www.catonett.com/blog/archives/194

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233/en-us

  ----------------------------------------------------

  And:

  Network connection problems
  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Windows Vista detects the wireless network but will not connect to it. Two other users in the same office connect without difficulty.

  The title says it all really.

  I was connected and working normally for about an hour this morning, until suddenly the connection has been lost.
  Windows detects the wireless network but will not connect. Two other users in the same office connect without difficulty.
  Help, please.
  Thank you.
  original title: vista detection network but will not connect

  Hi JulianBeach,

  1. you have made no changes to the computer before the broadcast took place?
  2. What is the exact error message you get?
  3 is connected to the domain of the computer?
  4. what happens when you try to connect to the network?

  Try the steps from the following link:
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Additional information:
  Wireless network card: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows-Vista/wireless-networking-frequently-asked-questions

• wireless authentication failed because of timeout on new router

  Wi Fi nightmare!

  We bought a new router as we couldn't find MSI we bought the ASUS!

  ASUS WL-520GC router =>

  Wireless authentication failed because the timeout. Layer 2 security key exchange did not generate multicast keys before timeout. I have a Windows vista with the latest Service Pack installed on an Aspire 7520-5115. What I'm doing wrong (I'm a semi ILLITERATE computer!)?

  We bought a new router as we couldn't find MSI we bought the ASUS!

  ASUS WL-520GC router =>

  Wireless authentication failed because the timeout. Layer 2 security key exchange did not generate multicast keys before timeout. I have a Windows vista with the latest Service Pack installed on an Aspire 7520-5115. What I'm doing wrong (I'm a semi ILLITERATE computer!)?

  Help you contact your ISP or ASUS. This isn't a problem of Microsoft.