Wireless printing to a printer via linksys router.

Similar Questions

• Connection to a wireless - printing Via Ethernet network?

  Hi, I had a search here but you can't find what I'm looking for, sorry if it was taken!

  I just bought a HP C310a wireless all in one, very happy so far.

  I connected my Netgear DGN2200 wireless, job done. I printed the test page and all is well.

  I'm now trying to set up my PC to print through my router via an Ethernet connection, but I've hit a brick wall!

  I tried to connect via usb and then try to go wireless, but it will not find the printer. I have also run the program quotes but it does not find the printer?

  Any ideas please?

  Thank you.

  OK, another problem as well!

  I just tried to connect with my wireless laptop and it failed. Looks like maybe that's a problem with my Netgear router?

  This rule!

  Just in case anyone else has this problem, it was down to my speed on my router settings. Speed has been set to "up to 300' and I reduced it" up to 145', and it worked very well, both wireless and ethernet. "

• printer via usb router two computers to access

  I have a Canon iP4300 printer connected to my router via a USB port. I am running Windows7 Home Premium (x 86 on my laptop (connected WIFI)) and Windows7 Home Premium (64-bit) on my office (LAN connected).

  The printer works fine from my laptop - it was the first to be connected to the printer.

  However, during one attempt of the same exact configuration of my desktop (again) - I get "the printer cannot be contacted over the network.
  I used the own methods windows for the installation of the printer and it was OK and went through the Setup without a hitch. It's only when I got to print a test page that nothing happened. On verification of the device in printers and devices that I noticed an exclamation point on this printer on execution of the troubleshooter, and were done with the above result.

  Don't know if this will help, but here is the report:
  Devices and printers

  Problems found
  CANON printer cannot be contacted over the network
  Contact your network administrator
  Problem with printer without current issue
  Any problems that have been checked without current issue
  CANON printer is not shared with the homegroup without current issue
  Printer paper is low or empty without current issue
  Printer toner is low or empty without current issue
  Printer has a paper jam now childless
  Printer driver requires update no current issue
  Printer is off without current issue
  A print job in the print queue is preventing another printing of f...             No current issue
  The print spooler service problems of print spooler service is not running without current issue
  CANON is not the default printer
  No current issue
  Problems found
  < printer="" canon="" cannot="" be="" contacted="" over="" the="" network                     ="" not="">
  Network problems may prevent the printer from printing.

  TCP/IP printer port
  Port name: CANNON
  Port number: 9100
   
  Contact your informational network administrator
  Windows cannot solve the problem. Please contact your network administrator.

  Problem with printer detected
  There could be problems with CANON. Windows will take additional steps to continue troubleshooting.

  Potential problems that have been verified - (show all 'Does not present edition')

  Details of detection

  Diagnostic information (network card)
   
  Network card diagnostics information:
    
  Network adapter driver to connect to the Local network information:

  Description...:
  Realtek PCIe GBE Family Controller
  Reference of the manufacturer.... : Realtek
  Provider of...: Realtek
  Version...: 7.45.516.2011
  INF file name... . : C:\Windows\INF\oem2.inf (NB: I also tried an inf file that is downloaded from the website of Canon via the driver file.)
  Date of the INF.... January 26, 2012 03:41:59
  Name of the section.... : RTL8168E.ndi hardware... ID: pci\ven_10ec & dev_8168 & rev_06
  Instance... state flags: 0x180200a
  Status code of Device Manager. . : 0
  IfType  . . . . . . . . . . . . : 6
  Type of physical support...: 0

  Network Diagnostics log
  File name: F2B2D1FB - 07B 5 - 43E2 - 8 d 15. 965B6653BE52 Diagnose.Admin.0.etl (it is a pirated copy of the .etl report).

  Other newspapers and Network Configuration
  File name: NetworkConfiguration.cab

  Publisher details...

  A question, I thought that can be a problem, is that two computers use the same port (9100) even if I started adding the printer, while the laptop was on and Windows seemed to correctly identify it.

  My setup real basis is:
  Canon of general
  Location: http://192.168.1.1:631/printers/CANON
  Model: Canon iP4300 (this changes a little when I used different drivers)
  NB: Don't know if this helps, but I can't change ' paper available:' default > no matter what I do with the printer preferences?
  Sharing is off
  Http://192.168.1.1:631/printers/CANON ports > Port TCP/IP Standard > Canon iP4300
  Security... I did all what I can in an attempt to make sure there is no robbery here.

  AND as stated above... it all works very well from the laptop.

  So, any suggestions?

  Hi Snapafun,

  Try the steps in this link, it worked for me.

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

• Problems with a printer via wireles router two laptops, test message says not UPnP supported 0 x 80070035.

  Have checked all resorcess so far, error message microsoft search bar after kodak printer has 0 x 80070035

  Hello

  • What is the full error message that you receive?
  • What were the changes made before the problem occurred?

  You can view these methods:

  Method 1:

  I suggest you to disable any program of security on your computer and check if it solves the problem.
  After reviewing the question you must reactivate the security on your computer program.
  Note: Run the computer without antivirus software or firewall is a potential threat to the computer; Be sure to activate security software after completing the troubleshooting steps and after identifying the problem.

  Method 2:

  Alternatively, you can try to uninstall the Kodak drivers and reinstall it and check.

  http://Windows.Microsoft.com/en-us/Windows-Vista/uninstall-or-change-a-program

  http://Windows.Microsoft.com/en-us/Windows-Vista/install-a-program

  See also:

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

• I'm trying to view the photos on my pc on my tv samsung, which has a wireless connection to the computer via the router. I spent a lot of time setting up, but it still does not work! Work.

  Recently I bought a Samsung smart tv I want to connect it to my pc so that I can view the pictures and videos on my TV. I have a connection through the modem but the pictures do not appear on the TV.

  I did the same thing only to realize that a standard USB cable will not work. Make sure that you connect your computer to your TV using a HDMI cable standard. They are not perfectly retangular than a USB cable and have edges around the corners of slightly rounded connectors. Can be purchased at most stores computers or shack radio for about 17 or 18 dollars 6 feet long.

• I have my printer connected to my router via a usb cable... I also have my (Vista) computer connected to the router by ethernet cable. How can I set the computer to print on my prints through the router?

  I have my printer connected to my router via a usb cable. I also have my (Vista) computer connected to the router by ethernet cable. How can I set the computer to print to my printer via the router?

  Usually, you need to install the printing software / drivers on your PC, configured / installed specially for a printer "remote" (its an option in the installation of the printer software)

• LaserJet p1505 for connection wireless printing

  I have a Laserjet P1505 (not 1505n) a Net Gear N600 dual band Router router with USB port and printer. I tried to connect the printer USB cable to the USB port on the router and installed the printer on the laptop (a Windows Vista) I'm trying to save up for a wireless printing capability. The updated drivers from HP Web site, set to turn on printer 'sharing' but the printer does not appear in the network and sharing Center. Have directly connect the printer USB cable to the computer laptop USB port to print from the laptop.

  I missed something or cannot print via the router P1505 (without the "n")?

  Thank you

  I found a post where a similar problem has been resolved. The user has enough to show what he has done to help others like you. I hope this helps.

  OfficeJet 7210 won't install with Netgear N600 router

• Printer HP Photosmart more B210 loses the wireless connection. with MAC 10.6 and Linksys router.

  From time to time my printer HP PSt + B210 indicates not 'online' in the window of the printer utility and do not print.

  I have spend hours to review what I did in th past and become confused.

  Should I start with the HP utility and make sure that my printer is listed only once in the queue (as is sometimes show 2 forms - for the same printer) OR should I stop MAC PB > router > Modem and then restart in correct, reverse order?

  Given that I need to choose "IP automatically...". ", I used Safari and put the 192.168.1.1 in the address bar and follow these steps, as already suggested.  What would be the clear measures to reconnect my HP printer status online? Thank you very much!!

  We will set an IP address of the printer:
  
  -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
  -Enter the IP address in a browser to reveal the internal settings of the printer.
  -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). You can find the beach DHCP from the router using its internal settings page or in its manual. Use the CD that came with your router or type the IP address of the router (ends para.1) in a browser.
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Enter the IP of your router (on the Page of the Network Config) for the bridge and the first DNS. Let the second white.
  -Click 'apply '.
  
  Now, stop the router and printer, start the router, wait, and then start printing.
  
  After that, you will have to redo 'Add printer' using the new IP address.

• HP wireless printer (3545) showing only printer and scanner, connected via Wireless

  When I connect via USB, I see Print/Scan option in the settings system-> Printers & Scanners

  But when I connect through wireless, I only Print

  What is the problem?

  Even in the HP utilities, I don't see this option "Scan to Computer" when it is connected to the wireless printer

  Hi TahseenJamal,

  Thanks for the video, which has been most useful.

  I suspect that the router can be not broadcast the Hello Protocol as it did in the past. To resolve this problem, please follow the instructions below.

  1. Out of the router, unplug the power cable
  2. Out of the printer, unplug the power cable
  3. Stop the Mac
  4. Give up everything for 1 minute and then reconnect the router
  5. Once sighted routers are on, reconnect the printer to the
  6. When the wireless printer is solid, turn on the Mac
  7. Now try to add the printer that you had previously, you should now see the Hello or Hello printer multifunction beside him.

  If this does not resolve the problem, it could be the printer. Follow the steps below.

  On the front panel of the printer, the arrow down to settings, then press OK. Down arrow for wireless and press OK. In the wireless menu, go to IPV6 and turn it off. Once IPV6 is disabled, try to add the printer in the preferences system again.

  Please let me know if either of these solutions solve the problem and if one of them, please also let me know, thanks.

• OfficeJet pro 8620: HP 8620 won't print via wireless for nay on my home mac

  I have 2 Macs in my home, Macbook, and Macbook Pro running Yosemite. I tried to implement a pro 7310 office via an ethernet cable printer to print wireless from these two macs and after 3 frustrating months trying everything that I could find, I bought the 8620 thought that would solve everything.

  Instead, it's the same. I am trying to print from firefox or word or anything and it cannot find the printer. But if I turned off everything, including the Mac and the router (N of Belkin N300 router wirleless) and the computer and then turn them back on, the printer is detectable and prints well. It just seems to disappear and I can't find it when searching for available printers after a few hours. I installed the last softeare for this printer and it worked when fine forst, implemented.

  Any help would be greatly appreciated that I spent way too many hours trying to figure this, it doesn't help that I'm not that tech savy.

  Thank you!

  Hello @bokke ,

  Welcome to the HP forum.

  I understand that you are having problems of communication between your two Macs and your 8620.

  I would like to help.

  Three things have caught my attention.

  You said that this is happening to both computers.

  You also mentioned that the same thing happened to another model of printer.

  Finally, after you power cycle your network everything works. At least for a little while.

  I feel that we should seek less software and more to your network.

  Belkin N300 wireless N Router, how old is this router?

  How is the printer to the router?

  Your router should have the following configuration

  ~ The multicast must be on or enabled (allows connectivity Hello)

  ~ Wireless Ports, they can also be frozen in security software:

  The incoming (UDP) ports: 137, 138, 161, 427

  Outgoing (TCP) ports: 137, 139, 427, 9100, 9220, 9500

  ~ Our printers support only the 2.4 GHz not 5 GHz

  ~ Recommended that the network name and password DO NOT containing and spaces/punctuation or special characters ~ Dual Radio enabled (for b/g wireless & networks n)

  ~ Mac disabled filtering

  ~ The built-in firewall must be the default or the lower settings

  This should solve the problem.

  PORTS TO UNLOCK.

  UDP: 137, 138, 161, 427, 80 & 443

  TCP: 137, 139, 427, 9100, 9220, 9500, 5222 5223

  So please make sure that multicast & Hello are enabled. Also never hurts to check for an update of the firmware.

• Unable to connect a wireless printer with laptop computer since the reset wireless router

  I have a wireless HP C4580 printer that connects to my Acer Aspire laptop using windows 7. The two have worked together very well for months.  My wireless router stopped working a few days ago, so I had to unplug the device to make it work again is it.  But since then, I can't get my lap top to communicate with the printer now.
  I went all the problem of shooting and insured the printer is on line and set it as default printer. I even did a system restore, as suggested in the troubleshooting
  With the help of the program are the two messages that I get now troubleshooting
  1 that the C4500 series can be contacted via the network (this is the message that I had before the restoration also)
  2 the C4500 series is not shared with the homegroup

  All the tips are greatly appreciated in progressive simple language as possible as I am a bit useless with computers

  I assume that the printer is all first directly connected on the router, then the laptop?  Access the router and make sure that the printer is listed as a "wireless client" connection  If this isn't the case, you should probably restore the wireless "link" between the printer and the router then the printer should work.

• HP7310 wireless printing with a new laptop &amp; Vista and existing wireless router?

  I just started to the top of my new laptop running Vista and have an existing HP all in one single 7310 and router wireless. I don't know what I have to do this printer works wirelessly. After talking with sales of HP, they tried to upsell me to "Wireless G Print Server" for a new printer. retailers say all I need is an adapter USB; I don't know what else I need this sunrise a race? Can anyone help?

  If your printer and router are close to each other, I would recommend via ethernet to your printer to your router connection.  Then follow these instructions.

  If you need to connect the printer to the wireless router, because they are in different rooms, you can use a wireless print server, but I'm not sure it is worth the money and the headaches - just get a new printer wireless - IMHO, of course.

• P1102w printer: have new router and can not figure out how to print wireless at P1102w printer - he sees old router

  I installed a new router (Netgear R6220) and cannot figure out how to get the P1102w printer to recognize the new router. It shows the former name of the router (Belkin.833) on the test page and displays the IP address configured by AutoIP rather than DHCP as the old router does. The computer is a desktop Dell Dimenstion about 3 years and use Windows 7. The router connects to the computer to the Internet.

  Help - How to make the printer recognize and communicate with the new router? (The original installation instructions don't seem to work for me.)

  I made an update of the firmware a few months ago and the currtent datecode is 20130703. Allowed to print from my Samsung S2 Tablet through the router.

  Here's what finally worked.

  1 had to withdraw from old installation CD but Uninstall selected, so I completely shut down the computer. Guy at Best Buy said to "remove the device" but it was not enough.

  2. download install the latest software from the HP download site and ran it. (http://ftp.hp.com/pub/softlib/software13/COL32431/bi-80329-11/hp_LJP1100_P1560_P1600_Full_Solution-v20120831-50157036_SMO.exe)

  3 downloaded another file and ran it. (Setup_IP4, [192_168_1_5], [NPI073E2D] _it) Not sure where I found this one, but the software prompted me to run.

  Finally, everything works and all devices are wireless printing

• All-in-one 1510 printer, router LinksysWRT54GSv4, use to set up my wireless printer?

  I have an all in one printer 1510 and I also have a LinksysWRT54GSv4 itinerary that is not used. My question is this, can I use this router to set up my wireless printer? I can be whistleing in the wind, but I need to know before you dispose of it. Thanks in advance for your consideration, I remain, sincerely greartful.

  paulq

  Hello

  Based on the following link, the printer doesn't have a wireless card so you can't use only a router to make wireless unless your router is also a print server, in this case, it is not.

  http://h10010.www1.HP.com/wwpc/us/en/SM/WF06b/18972-238444-410635-12085-F57-428822-428823-428855.html?DNR=1

  Kind regards.

• I GOT A NEW ROUTER FROM VERIZON ACTIONTEC GT784 INSTALLED BUT NOW CAN'T USE MY MX340 WIRELESS PRINTER HELP

  I GOT A NEW ROUTER FROM VERIZON ACTIONTEC GT784 INSTALLED BUT NOW MY PRINTER DOES NOT PRINT. MX340 WIRELESS PRINTER. CLOSE

  Hello

  To help you to propose measures to solve the problem, I would appreciate if you could answer the following question:

  1. what version of Windows operating system is installed on the computer?

  2 successful wireless connection configuration?

  3. do you receive an error message or error code when trying to print?

  In the meantime, I suggest to add the device on the network and check if that does the trick. To do this, follow these items:

  Connect to Bluetooth and other wireless or network devices

  http://Windows.Microsoft.com/en-us/Windows7/connect-to-Bluetooth-and-other-wireless-or-network-devices

   

  Add a device or computer to a network

  http://Windows.Microsoft.com/en-us/Windows7/add-a-device-or-computer-to-a-network

   

  Sharing of files and printers

  http://Windows.Microsoft.com/en-us/Windows/sharing-files-printers-help#sharing-files-and-printers=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Hope this information helps. Reply with more information about the issue so that we can help you better.