Similar Questions

• Implementation of Airport extreme with the same SSID

  My House has very thick walls and so I run a Cat5 cable for a number of rooms and installed an Airport Extreme for everyone to create a local WiFi network.

  For the moment, each creates its own wi fi network which is very good for connecting phones, tablets and laptops but I'm trying to connect some SONOS devices and they are not find each other so not a link to the main controller of SONOS.

  SONOS support suggests that if I could get the extremes of the airport on the same SSID, which should help you because they would all be network extensions and so devices would be able to find each other.

  I tried making them all extensions of the network wi fi router but can't see not in the options when I select "Extend an existing network", although on my iPad, I can see wi fi network to the router where the Airport Extreme is so too, it is wired to the router would have thought it should be possible to make all the extensions of a single network.  Research in the community, it seems that the airport is unable to extend a wifi network not Apple, but I could at least get all the airports on the same SSID can help.  I also tried to set up airports so they all extend the network, but they do not see each other because they are too far away.

  I'm not an expert in network management, I understand bits having to solve problems earlier, but if there is there advice or suggestions of the community that would be great

  Thank you

  David

  You choose to extend a network when the incoming signal is wifi. What you need is a "mobile network". Simply connect each airport to the router by ethernet and network with the same SSID and password than the original. Reset the airports so that they put in place from the new so that they detect the arrangement and get into bridge mode - you do not want to provide the IP numbers, you want the home router to do and airports to pass.

  See this page and scroll down to "Roaming Network (Wi - Fi connected base stations)':"

  Wi - Fi base stations: extend the reach of your network wireless by adding additional base stations Wi - Fi - Apple Suppo...

• the same SSID used on 3 sites and even vlan assignment client IP?

  our 5508 controller and LW APs to IP phone 7925 G wireless

  Controller is installed at A site and there are APs and wireless to the site B and C as well.

  1. can I use the same SSID for the three sites for cordless phones? or having to use separate SSID 3?

  2. If I use the same SSID, can I associate a subnet for example 10.10.131.0/24 for the 3 sites Cordless IP phones? (our UCM Cisco is fine with that)

  3. If I use 3 distinct SSID, must I give three subnets for IP phones on three sites?

  Thanks for the help!

  Eric

  Yes you are right... but its recommended to configure HREAP for remote offices... so that the failure will be less compared to the AP in local mode...

  Let me know if that answers your question...

  Concerning

  Surendra

• Problem of airtime with the same SSID

  I often use AirPlay to my iPhone and iTunes on my PC to play for my (home theater installation) AVR - 1506 Marantz.

  Configuring wifi in our House are a router/modem to the ISP and an Asus RT-N56U (in access point mode) with DIFFERENT SSID to which I don't have problem to play AirPlay on any device. I had the same SSID when so I can use wifi roaming without having to change the SSID whenever the other signal weakens.

  When I put two (router & AP) with the same SSID, Airplay icon will not be displayed? But if I put a different SSID to one of the two, airplay icon is back. Channels are on ch.1 (router) and ch.11 (AP). Someone knows how to set up?

  UPDATE:

  Disable NAT in fact access point the AirPlay icon always appear but he cannot yet play through my APR.

  * all updates *.

  12.4.3 iTunes

  Windows 10 updated, firewall offshore

  Marantz 1506 firmware update

  always put iPhone to update to the latest version

  The routers are also updated to its latest firmwares

  What I believe you are describing is a network expanded through repetition, the Apple TV does not work well with repeaters. Try a different configuration.

• Satellite R830-1GZ: ConfigFree Radar fails to display the networks without wire with the same SSID

  I have a new R830-1GZ Satellite with Windows 7 and a (much) older Portege M300 - all have two versions of Radar on them.

  However, while the old machine display correctly anywhere wireless and signal forces - even when there are multiple places with the same SSID - I use Powerline Extenders to extend coverage, the new machine with the last RADAR doesn't seem to be able to cope with these multiple identical wireless spots and fails to show more than one at a time - and then reliably.

  I should add that both machines work quite well in fact using the same SSID points connecting to the stronger.

  Is there a utility round way this or another that correctly displays it available different SSID and strength.

  Thank you very much

  Bill

  > Is there a utility round way this or another that correctly displays it available different SSID and strength?

  As far as I know there is no other Toshiba utility that could manage wireless networks and display devices Bluetooth as ConfigFree don't.

  I found some useful Q / A ConfigFree regarding:
  [ConfigFree: answers Questions &: http://www.toshiba.eu/innovation/solution_content_article.jsp?z=42&SOLUTION_ID=Conf igFree_QandA]

  Look also in Toshiba's technical knowledge base and search for Configfree for useful documents.
  http://www.Toshiba.EU/innovation/generic/TKB_SUPPORT/

• 3070 connectivity problem - multiple Accespoints with the same SSID

  Hi all

  I have a problem with my printer HP Deskjet 3070 printer all-in-one.

  I have 2 accespoints with the same SSID for better coverage of the pit of the wireless home network.

  For some reason any my HP printer keeps losing wireless connection when the 2 accespoints are rising.

  I use a different frequency for the 2 accespoints channel and it works fine with all other wireless devices.

  I did that a DHCP are used, r, but in fact it doesn't matter because the printer uses a static IP (192.168.0.3)

  When the two AP is the printer loses wirelesss connectivity. (The blue led will blink)

  If I take one of the accespoints offline, the printer becomes available.

  Is this a problem on my end or a problem of software/firmware printer?

  Kind regards

  -eth0

  Lol this is not very clear to me?

  But it is very good that we continue here:

  http://h30499.www3.HP.com/T5/printers-DeskJet/3070A-connectivity-issue-multiple-Accespoints-with-the-same-SSID/TD-p/5865699#.UKNyiYatlI1

• LAPN300 - the best configuration for 3 access points, while using the same SSID

  Hi all

  What is the best configuration for 3 x LAPN300 located in various places around my house of 3 floors, access points if I want just one SSID?

  I did some initial research which suggests that I can use the same SSID on all three, as long as they are on different channels. 1, 6 and 11 for example. In theory, then, as I wander around the House the client machine must auto swap to the AP with the signal stronger.

  What do you think? What is the best way or do, or could suggest you something else?

  As an aside... If I decided to create a second SSID for the guests at home, I would also want to add wireless isolation to this SSID. How would that be managing the DHCP server on the local network? How would be asked to connect to the SSID has never get an IP if they have been isolated from other clients on the local network?  Besides, how they see the router? The ANNUAL lets you specify exceptions to this isolation for this feature?  Alternatively, as I suspect, is the right isolation feature isolate them from other WLAN, not the LAN clients customers?

  I did some testing and configuration of the AP with the same SSID and security will do what you want. Don't worry about setting the channel because the auto channel setting works with these devices and automatically adjusts the spacing between the appropriate channels.

  Recommendation of the VPN_user is what you need if you want to isolate the SSID comments from the rest of your network clients.

  Isolation of SSID of the AP will guard only wireless devices to communicate with each other on the same SSID on which it is enabled.

• 2 with the same SSID E3200

  Hello

  I want to install the following in a new House and I am looking for your help.

  House has 2 floors. I want to install 2 E3200, one on each floor, but with the same SSID and password, etc. so internet connection / streaming throughout the word is flawless. Is this possible?

  Both floors have taken wall ready network and they all lead to the same modem/router, so all devices connected lead to the same network.

  Thanks in advance.

  Bonez

  PS. the two E3200 was last updated Firmware Version: 1.0.03

  1. If your modem is a router, you should consider implemented the two E3200 (i.e. as access points) and not as a router bridge mode. Chaining routers can cause various issues, including the offsets and disconnects. There is generally no reason chain routers in a home network, you probably want all interconnection.

  2. otherwise, if you want to use an E3200 as a router (for example because the modem/router don't provide some functionality of routing/firewall you want) you should put the modem/router mode "bridge" device It transformed into a simple modem, and you can then reconfigure your E3200 for your internet connection (for example PPPoE for DSL) or DHCP for cable. The first E3200 then functions as normal internet router. The second should still be used in bridge only mode.

  3. If your first router is 192.168.2.1 and the second was 192.168.2.200 and you connect through the second port of the internet router and you put not the second router mode bridge, you will get a working network. The second router works as a router and has the 192.168.2. * subnet identical IP on the internet port and the LAN side. It is cannot be routed. It would never work. If you connect two routers, LANs should not overlap (this is why you have to change the first router 192.168.2.1 IP, because your modem/router uses address of 192.168.1. *). If you define 192.168.3.1 as the second address IP LAN E3200 you can connect the internet port of the second to the first E3200 and you can use the second E3200 as router.

  4. However, if you run both as a router with different IP subnets (which is mandatory if the second operates as a router) you cannot set up a roaming network. A unique SSID is supposed to link to the same local network. A wireless client assumes that moving from one access point to another on the same SSID to connect to the same local network, that is, he can always use the same DHCP IP address and everything else looks the same on each access point. However, with two routers routing, you have two different and two IP subnets different local networks. So for roaming, is not possible.

  So, I recommend you:

  a. place if possible the modem/router to bridge fashion and use it as a simple modem only. Configure the first E3200 as internet router on LAN IP 192.168.1.1. Implement the second E3200 mode bridge on a static IP 192.168.1.2. Connect the internet port of the second to the first.

  b. If you need to keep the modem/router as a router on 192.168.1.1, put in place the two E3200 in Bridge mode and assign the first one address static IP 192.168.1.2 and the second a static IP address of 192.168.1.3. Use the internet ports for the connection.

  c. If you insist on chaining an E3200 as router to your modem/router, do the same configuration that (a.), but use 192.168.2.1 and 192.168.2.2 to the IP addresses of the first and the second.

  Whatever it is, you can configure a roaming with the settings wireless wireless network as described above.

• What is WEP, WPA and WPA2?

  Can be implemented to your WiFi network and want to know what the difference between WEP, WPA and WPA2.

  This short video covers some of the basics of WEP, WPA, WPA2 and why security is important.

  I hope that answers some of the fundamental questions that anyone may have.

• Must configure with the same SSID of the AP

  We are looking for the purchase of two Access Points to our new building.  We currently have at our old facility two end bottom of AP with two different SSIDs.  Manaully users simply switch between the two.  I would like to know how it would be difficult to set up it would not have users to manually switch as they traveled through the building.

  I have looked at Cisco AP below and I was wondering if she had the ability to do so.  Is there another hardware or software needed to put up something like that.

  Just to clarify I only need two AP and want things transperent to my users.  I want them to be able to walk the area covered to another area covered by the AP2 and AP1 and loose no matter what connection.  Here it's automatic for users do not have to do anything to move things.

  Any info anyone can provide to help me would be greatly appreceated.  Thanks in advance.

  Access point wireless Cisco Aironet 1140 AIR-LAP1141N-A-K9

  As I understand it, you can configure both with the same SSID settings and security and that they will be 'transparent' to switch to the other. It is if you do not use something like an IP phone that requires a quick transition between the two. In this case, you would need a controller.

• on the Iphone 7. How to listen to music, if we have a normal headset and charge at the same time?

  How to listen to music, if we have a normal headset and charge at the same time?

  < re-titled by host >

  It sopposed must be a wireless charging dock to be launched shortly if the dock does not so it is a disappointment

• When I opened my firefox on my mac - it opens to a blank screen. I tried to remove and redownloading but the same thing happens. How can I fix?

  When I opened my firefox on my mac - it opens to a blank screen. I tried to remove and redownloading but the same thing happens. How can I fix?

  Ahh. I thought you meant Subject: vacuum

  Start Firefox in Safe Mode {web link} by holding down the < shift >
  (Mac options) key and then from Firefox. Is always the problem?

  Start your computer in safe mode with network. Then launch Firefox.
  Try the sites secure web. Is always the problem?

  Start the computer in Mode safe;
  Free online encyclopedia

• can not put cookies and exceptions on the same screen. Need to fix this.

  Went to the options today and the format has changed. Now I can't put Cookies and Exceptions on the same page at the same time. It is vital that I can put together up to manage cookies. Please fix this. Anyone have any ideas?

  You can enable/disable browser.preferences.inContent false on the topic: page config to restore the autonomous Options/preferences window you had in previous versions of Firefox.

  You can open the topic: config page via the address bar.
  You can accept the warning and click on "I'll be careful" to continue.

  • http://KB.mozillazine.org/about:config

• I have two computers on the same router. One, on Xp and Eudora normally receives. The second on WIN-7 and Thunderbird receives the same messages in code -?

  I have two computers-
  On WinXp and Eudora receives emails in normal text.
  Sometimes, the other on Win-7 and Thunderbird receives the same message in code.
  Normally, this same message is received on the other computer.
  What have I've set wrong
  GerryMcDonald

  Start with view-> Message-> HTML Original body

• My iphone 6 does not light, I held the home button and power at the same time and no vibration or no sign of life, any suggestions as to what it could be would be appreciated

  Phone bought 3 days ago and I fight to turn it on, it's just a black screen, the phone records into iTunes but does not turn, I tried holding down the home button and power at the same time and still nothing, I presume that it's a battery problem as if it was the backlight then the phone vibrated when you press the power button help Please!

  Marley6921 wrote:

  Phone bought 3 days ago and I fight to turn it on, it's just a black screen, the phone records into iTunes but does not turn, I tried holding down the home button and power at the same time and still nothing, I presume that it's a battery problem as if it was the backlight then the phone vibrated when you press the power button help Please!

  Put it on wait ten minutes if the phone did not come one, then hold down the sleep/Home button until you see the apple logo and then release, make sure that the phone is still connected to the charger.