WRE54G amplifier does not not with WRT610N router

Similar Questions

• There is an error with my computer, it does not connect with my router. It works with my usb 3g modem, but not with my router. My router works with other devices.

  There is an error with my computer, it does not connect with my router. It works with my usb 3g modem, but not with my router. My router works with other devices.
  I tried to connect my xbox to my computer to xbox live via the 3g router, but I was unable to. According to me, there is something wrong with the network card, since neither the wifi (wlan?) nor the lan connection seem to work.
  I harnessed connected my iPod, Xbox 360 and Nintendo DS for her, but not my computer. Please help me, what wrong with my computer?

  original title: problem with the map?

  Hi GustavTak,

  1. you have made no changes to the computer before the broadcast took place?
  2. do you get an error message?

  Try the steps from the following link:

  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Additional information:
  Network connection problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  Set up a wireless router
  http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-a-wireless-router

• WRE54G canmot associated not with this access point in Repeater mode.

  Hello

  Because of the concrete walls, I have a weak signal to use the WRE54G to extend my existing wireless network. However, I installed an Ethernet cable and found possible to connect the WRE54G access point. This is my extension of network is via a connection to an Ethernet cable. Is seems to work fine, it allows communications to the internet and shows a power good signal from a remote PC. But it works only in unsafe mode.

  Although I tried to reset, and then follow the instructions to set up a new WEP or WPA encryption, the installation program recognizes the WRE54G, but does not allow me to save the configuration.

  The error it says it is "WRE54G canmot not associate with this access point in Repeater mode.

  Help, please

  Make sure your router's wireless settings and WRE are the same. Try changing the channel on your router, if your router's wireless channel is the default after the procedure, your WRE is unable to communicate with your wireless router.

• My canon printer mx420 does not see my router to access point

  My canon printer mx420 does not see my router to access point. What can I do about it.

  Hello Rick,

  I went online on the website of Canon, and there were 25 games for "printer sees router access point; you might want to try this page: http://www.usa.canon.com/cusa/support/consumer/printers_multifunction/pixma_mx_series/pixma_mx420?CMD=MIXED_SEARCH&mName=PIXMA+MX420&mType=PIXMA+MX&pageKeyCode=ekbresults&searchString=doesn't+see+router+access+point&BASIC_SEARCH_CURRENT_TOPIC_ID=1076&BASIC_SEARCH_CURRENT_TOPIC_TYPE=0&RESULTS=RELEVANCE&RELEVANCE_START=1&RELEVANCE_COUNT=25&CONFIGURATION=1011&PARTITION_ID=1&TIMEZONE_OFFSET=null&USERTYPE=1&isSecure=false .

  If you have no luck after visiting the Canon site, post back here with what you tried, and we'll go from there. I hope this helps you.

  Kind regards

  BearPup

• Why apple card app does not show the routes and directions between two places in India in an iphone 6 s more?

  map does not show the routes and directions

  This feature is not yet supported in India.

  http://www.Apple.com/in/iOS/feature-availability/#maps-directions

  In addition, your phone may be overheating for a number of reasons. The most common of which is low service area.

  Your attributes from battery to the majority of the production of heat, then adjust settings to put less load on the farm in general will help some.

  http://www.Apple.com/batteries/maximizing-performance/#iOS

• Once I changed my ISP my computer network does not work and does not recognize my router lynsys

  Once I changed my ISP my computer network does not work and does not recognize my router lynsys

  Hi George,.
  Please go to the Microsoft Community Forums.
   
  1. do you get an error message?
  2. do you have the internet connection wired or wireless?
  3. What is the brand and model of the computer?
   
  I suggest to refer to the links and follow the steps in the articles:
   
  Wireless and wired network problems
  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help?T1=Tab03#network-problems=Windows-XP&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1
   
  Resources for the resolution of the problems of modem in Windows XP
  http://support.Microsoft.com/kb/308022#top
   
  How to troubleshoot wireless network connections in Windows XP Service Pack 2
  http://support.Microsoft.com/kb/870702
   
  How to reset the Protocol Internet (TCP/IP)
  http://support.Microsoft.com/kb/299357#appliesTo
   
  If the problem persists, contact the Internet service provider for assistance.
   
  I hope this helps.

• WRT54G Ver.2 communicates is not with my router

  I have a WRT54G version 2 and it does not communicate with my cable modem.  When I go into the Setup menu I have an IP from my modem and I have the default gateway with DNS servers.  When I try to access internet, I can't.  I have ping all addresses and when I get to the front door my application has been exceeded.  I have not changed the settings and I tried power cycling, but it still does not work.  The funny things is when I hard plugged the laptop to the modem cable I can access the internet fine, but not through the router.

  Anyone have any ideas on what is happening with the solutions?

  What "Internet Connection Type" that you use in the router?  You should probably use "obtain automatically an address IP (DHCP)".

  If you would like more information, please indicate your ISP and the brand and exact model of your modem number.

• Nintendo Wii does not detect new router WRT160N...

  I got this new N Ultra Range Plus router for Christmas and thought it would finally so my Wii to the internet, but to my surprise, even though it detects the router, it does not connect. I get the Wii error Code: 51330. I searched on google with this code, and he was told to change the channel 1 or 11, I did, and that has not worked. Or put the address allow mac in the column, which also did not work.

  I really need help. I don't know why it does not work. Internet works fine on my computer, but for some reason, it does not connect on the Wii. And the router is very close to the Wii as far as space goes.

  You can change/adjust the settings of your wireless router...

  Open an Internet Explorer browser page. In the address bar type - 192.168.1.1
  Let the empty user name & password use admin lowercase...
  For wireless settings, follow these steps: -.
  Click on the tab - Wireless
  -Here, select manual configuratioon... Wireless network mode must be mixed...
  -Provide a unique name in the name box of the wireless network (SSID) in order to differentiate your network from your network of neighbors...

  -Set the Standard - 20 MHz Radio band and change the standard channel at 11-2, 462 GHz...

  - And wireless SSID broadcast should be enabled, and then click on save settings...
  Please take note of the name of the wireless network (SSID) because it's the network identifier...
  For wireless security: -.
  Click the sub-tab under wireless > Wireless Security...
  Change the mode of WEP wireless security, encryption must be 64-bit. Let the empty password, do not type in anything...
  Under type of WEP Key 1 in all 10 numbers please (numbers only and not letters) and click on save settings...
  Please take note of the WEP Key 1 because it is the security key to try Wireless Network.Now if you could see the network without wire/SSID name and try to connect...

  Click Advanced Wireless-
  settings > change the tag to 75 interval > change the Fragmentation...
  Threshold to 2304 change the RTS threshold to 2307 > click 'save settings '...
  Now let's see if you can locate your wireless network and try to connect...

• DMZ-Link bandwidth does not change the routing table countin traffic

  Hey guys

  I'm INE laboratories dong and shoved a weird one that delivers.

  I have configured the dmz-link bandwidtha nd the extended communities to send, I get the bandwidth in the BGP routes, however the routing table does not change the proportion of traffic according to the bandwidth available link.

  Here is my configuration:

  Rack1R6 (config) #do sh run | dry BGP

  router bgp 100

  no synchronization

  The log-neighbor BGP-changes

  BGP dmzlink-bw

  155.1.146.0 netmask 255.255.255.0

  aggregate-address 155.1.0.0 255.255.0.0 summary only

  neighbour 54.1.1.254 distance-54

  neighbor 54.1.1.254 dmzlink-bw

  neighbour 155.1.67.7 distance-300

  neighbour 155.1.146.1 distance-100

  155.1.146.1 neighbor send-community times

  No Auto-resume

  Rack1R6 (config) #.

  Rack1R6 (config) #do sh ip bgp neigh 155.1.146.1 opponents

  Version of BGP table is 35, local router ID is 150.1.6.6

  Status codes: deleted, cushioning d s, history of h, * valid, > best, i - internal.

  r SIDE-failure, stale S

  Source codes: i - IGP, e - EGP,? -incomplete

  Network Next Hop path metrics LocPrf weight

  * > 28.119.16.0/24 54.1.1.254 0 54 I

  * > 28.119.17.0/24 54.1.1.254 0 54 I

  * > 112.0.0.0 54.1.1.254 0 0 54 50 60 I

  * > 113.0.0.0 54.1.1.254 0 0 54 50 60 I

  * > 114.0.0.0 54.1.1.254 0 0 54 I

  * > 115.0.0.0 54.1.1.254 0 0 54 I

  * > 116.0.0.0 54.1.1.254 0 0 54 I

  * > 117.0.0.0 54.1.1.254 0 0 54 I

  * > 118.0.0.0 54.1.1.254 0 0 54 I

  * > 119.0.0.0 54.1.1.254 0 0 54 I

  r > 155.1.0.0 0.0.0.0 32768 I

  Rack1R6 (config) #do sh ip bgp

  Version of BGP table is 35, local router ID is 150.1.6.6

  Status codes: deleted, cushioning d s, history of h, * valid, > best, i - internal.

  r SIDE-failure, stale S

  Source codes: i - IGP, e - EGP,? -incomplete

  Network Next Hop path metrics LocPrf weight

  * i28.119.16.0/24 204.12.1.254 0 100 0 54 I

  *>                  54.1.1.254                             0 54 i

  * i28.119.17.0/24 204.12.1.254 0 100 0 54 I

  *>                  54.1.1.254                             0 54 i

  * i112.0.0.0 204.12.1.254 0 100 0 54 50 60 I

  * > 0 0 54 50 60 54.1.1.254 I

  * i113.0.0.0 204.12.1.254 0 100 0 54 50 60 I

  * > 0 0 54 50 60 54.1.1.254 I

  * i114.0.0.0 204.12.1.254 0 100 0 54 I

  *>                  54.1.1.254               0             0 54 i

  * i115.0.0.0 204.12.1.254 0 100 0 54 I

  *>                  54.1.1.254               0             0 54 i

  * i116.0.0.0 204.12.1.254 0 100 0 54 I

  *>                  54.1.1.254               0             0 54 i

  * i117.0.0.0 204.12.1.254 0 100 0 54 I

  *>                  54.1.1.254               0             0 54 i

  * i118.0.0.0 204.12.1.254 0 100 0 54 I

  Network Next Hop path metrics LocPrf weight

  *>                  54.1.1.254               0             0 54 i

  * i119.0.0.0 204.12.1.254 0 100 0 54 I

  *>                  54.1.1.254               0             0 54 i

  r i155.1.0.0 155.1.146.4 0 100 0 I

  r>                  0.0.0.0                            32768 i

  s > 155.1.146.0/24 0.0.0.0 32768 0 I

  * > i205.90.31.0 155.1.13.3 0 100 0 200 254?

  * 155.1.67.7 0 300 200 254?

  * > i220.20.3.0 155.1.13.3 0 100 0 200 254?

  * 155.1.67.7 0 300 200 254?

  * > i222.22.2.0 155.1.13.3 0 100 0 200 254?

  * 155.1.67.7 0 300 200 254?

  Rack1R6 (config) #.

  # now R4 configuration

  Rack1R4 (config) #do sh run | dry BGP

  router bgp 100

  no synchronization

  The log-neighbor BGP-changes

  BGP dmzlink-bw

  155.1.146.0 netmask 255.255.255.0

  aggregate-address 155.1.0.0 255.255.0.0 summary only

  neighbour 155.1.45.5 distance-200

  155.1.45.5 route-neighbour card GAME-54 on

  neighbour 155.1.146.1 distance-100

  155.1.146.1 neighbor send-community times

  neighbour 204.12.1.254 distance-54

  neighbor 204.12.1.254 dmzlink-bw

  No Auto-resume

  Rack1R4 (config) #.

  Rack1R4 (config) #do sh ip bgp Synt.

  Local router BGP 150.1.4.4 identifier UNDER number 100

  BGP table version is 18, table 18 main routing version

  15 entries for network using 1980 bytes of memory

  18 entries for path using 936 bytes of memory

  9/7 BGP path/bestpath attribute entered using 1512 bytes of memory

  3 entries for BGP AS-path ACCESS using 72 bytes of memory

  1 entries PMO community, using 24 bytes of memory

  0 cache entries of BGP route-map with 0 bytes of memory

  0 cache entries of filter-list BGP using 0 bytes of memory

  Bit entries in the cache field: 3 courses (up to 5) with 96 bytes of memory

  BGP using 4620 total number of bytes of memory

  Activity 102/87 BGP prefixes, 243/225, scan interval to 60 seconds

  Neighbor MsgRcvd MsgSent V AS TblVer InQ OutQ Up/Down State/PfxRcd

  155.1.45.5 4 200 8615 8640 18 0 0 07:38:02 3

  155.1.146.1 4 100 8761 8668 18 0 0 00:14:34 3

  204.12.1.254 4 54 8724 8595 18 0 0 07:38:02 10

  Rack1R4 (config) #do sh ip bgp

  BGP table version is 18, local router ID is 150.1.4.4

  Status codes: deleted, cushioning d s, history of h, * valid, > best, i - internal.

  r SIDE-failure, stale S

  Source codes: i - IGP, e - EGP,? -incomplete

  Network Next Hop path metrics LocPrf weight

  * > 28.119.16.0/24 204.12.1.254 0 0 54 I

  * > 28.119.17.0/24 204.12.1.254 0 0 54 I

  * > 112.0.0.0 204.12.1.254 0 54 50 60 I

  * > 113.0.0.0 204.12.1.254 0 54 50 60 I

  * > 114.0.0.0 204.12.1.254 0 54 I

  * > 115.0.0.0 204.12.1.254 0 54 I

  * > 116.0.0.0 204.12.1.254 0 54 I

  * > 117.0.0.0 204.12.1.254 0 54 I

  * > 118.0.0.0 204.12.1.254 0 54 I

  * > 119.0.0.0 204.12.1.254 0 54 I

  * > 155.1.0.0 0.0.0.0 32768 I

  s > 155.1.146.0/24 0.0.0.0 32768 0 I

  * i205.90.31.0 155.1.13.3 0 100 0 200 254?

  *>                  155.1.45.5                             0 200 254 ?

  * i220.20.3.0 155.1.13.3 0 100 0 200 254?

  *>                  155.1.45.5                             0 200 254 ?

  * i222.22.2.0 155.1.13.3 0 100 0 200 254?

  Network Next Hop path metrics LocPrf weight

  *>                  155.1.45.5                             0 200 254 ?

  Rack1R4 (config) #do sh ip bgp neigh 155.1.146.1 opponents

  Rack1R4 (config) #do sh ip bgp neigh 155.1.146.1 opponents

  BGP table version is 18, local router ID is 150.1.4.4

  Status codes: deleted, cushioning d s, history of h, * valid, > best, i - internal.

  r SIDE-failure, stale S

  Source codes: i - IGP, e - EGP,? -incomplete

  Network Next Hop path metrics LocPrf weight

  * > 28.119.16.0/24 204.12.1.254 0 0 54 I

  * > 28.119.17.0/24 204.12.1.254 0 0 54 I

  * > 112.0.0.0 204.12.1.254 0 54 50 60 I

  * > 113.0.0.0 204.12.1.254 0 54 50 60 I

  * > 114.0.0.0 204.12.1.254 0 54 I

  * > 115.0.0.0 204.12.1.254 0 54 I

  * > 116.0.0.0 204.12.1.254 0 54 I

  * > 117.0.0.0 204.12.1.254 0 54 I

  * > 118.0.0.0 204.12.1.254 0 54 I

  * > 119.0.0.0 204.12.1.254 0 54 I

  * > 155.1.0.0 0.0.0.0 32768 I

  * > 205.90.31.0 155.1.45.5 0 200 254?

  * > 220.20.3.0 155.1.45.5 0 200 254?

  * > 222.22.2.0 155.1.45.5 0 200 254?

  Total number of prefixes 14

  Rack1R4 (config) #.

  # and where is the real problem, R1

  Rack1R1(config-Router) #do sh ip bgp

  Version of BGP table is 15, local router ID is 150.1.1.1

  Status codes: deleted, cushioning d s, history of h, * valid, > best, i - internal.

  r SIDE-failure, stale S

  Source codes: i - IGP, e - EGP,? -incomplete

  Network Next Hop path metrics LocPrf weight

  * i28.119.16.0/24 54.1.1.254 0 100 0 54 I

  * > I 204.12.1.254 0 100 0 54 I

  * i28.119.17.0/24 54.1.1.254 0 100 0 54 I

  * > I 204.12.1.254 0 100 0 54 I

  * i112.0.0.0 54.1.1.254 0 100 0 54 50 60 I

  * > I 204.12.1.254 0 100 0 54 50 60 I

  * i113.0.0.0 54.1.1.254 0 100 0 54 50 60 I

  * > I 204.12.1.254 0 100 0 54 50 60 I

  * i114.0.0.0 54.1.1.254 0 100 0 54 I

  * > I 204.12.1.254 0 100 0 54 I

  * i115.0.0.0 54.1.1.254 0 100 0 54 I

  * > I 204.12.1.254 0 100 0 54 I

  * i116.0.0.0 54.1.1.254 0 100 0 54 I

  * > I 204.12.1.254 0 100 0 54 I

  * i117.0.0.0 54.1.1.254 0 100 0 54 I

  * > I 204.12.1.254 0 100 0 54 I

  * i118.0.0.0 54.1.1.254 0 100 0 54 I

  Network Next Hop path metrics LocPrf weight

  * > I 204.12.1.254 0 100 0 54 I

  * i119.0.0.0 54.1.1.254 0 100 0 54 I

  * > I 204.12.1.254 0 100 0 54 I

  * i155.1.0.0 155.1.146.6 0 100 0 I

  * > I 155.1.146.4 0 100 0 I

  * > 205.90.31.0 155.1.13.3 0 200 254?

  * i 155.1.45.5 0 100 0 200 254?

  * > 220.20.3.0 155.1.13.3 0 200 254?

  * i 155.1.45.5 0 100 0 200 254?

  * > 222.22.2.0 155.1.13.3 0 200 254?

  * i 155.1.45.5 0 100 0 200 254?

  Rack1R1 (config - Router) # do sh ip bgp 112.0.0.0

  112.0.0.0/8, version 4 BGP routing table entry

  Paths: (2 available, best #2, table by default-IP-Routing-Table)

  MPIO: eBGP iBGP

  Announced for the update-groups:

  1          2

  54 50 60, (from a customer-RR)

  54.1.1.254 (metric 2560002816) of 155.1.146.6 (150.1.6.6)

  Origin, IGP, 0, 100, valid, internal multipath localpref metric.

  DMZ-Link Bw 250 KB

  54 50 60, (from a customer-RR)

  204.12.1.254 (metric 2560002816) of 155.1.146.4 (150.1.4.4)

  Origin, IGP, metric 0, localpref 100, valid, internal, multipath, best

  DMZ-Link Bw 12500 KB

  Rack1R1(config-Router) #do sh ip route 112.0.0.0

  Routing for 112.0.0.0/8 entry

  Known through 'bgp 100', 200, 0 distance metric

  54, internal type tag

  Last update of 204.12.1.254 ago 00:15:30

  Routing descriptor blocks:

  204.12.1.254, 155.1.146.4, there is 00:15:30

  Path metric is 0, number of shares of traffic 1

  AS hop 3

  Beacon road 54

  * 54.1.1.254, 155.1.146.6, there is 00:15:30

  Path metric is 0, number of shares of traffic 1

  AS hop 3

  Beacon road 54

  Rack1R1 (config - Router) #.

  as you can see, the BGP process in R1 receives the correct link DMZ bw but not indeed take...

  can you please help me if I makeover anything in my setup?

  Hello

  Can you please make sure you have a value of bandwidth on ALL your BGP peering physical interfaces? And you can also include the running-config 'router bgp XXXX' out of R1 as you have not understood what we (others are). Just to make sure that you have "bgp dmzlink-bw' configured on all peerings and overall in the process - it will still show in the output of the same community if it does not work on it.

• I just spent an hour to compose a response in a thread ("Firefox does not with paypal"), only to see "You do not have permission" to submit - total loss!

  I was connected to respond in the thread "Firefox does not work with paypal. I spent the best part of an hour carefully compose this response, case tests, links, etc... [Tip: Firefox, unlike other browsers, has a problem with the server paypalobjects.comscripts.] Because I had taken so long to write the answer, she seemed to be a good idea to check in via the Preview button, but I received a message that the service was not available. Of course, I decided to submit it anyway, but when I hit 'submit' I got a message "you don't have permission...". "- at which point I (stupidly) on another page with this message, and what I wrote was gone!

  Anyway, it is definitely not normal that the site log out after only an hour. Sorry to hear about this. Maybe there was a little problem on the server with your session. If it is reproducible, I wonder if you have any software that could be quietly elimination of cookies for the inactive sites?

• Satellite Pro 2100 - works does not with 2 sticks of RAM

  Hi all

  I've been with sticks of 2 x 512 MB RAM from a reliable supplier that reassures me that this RAM is compatible with the SP2100 laptop.

  With the two sticks installed, as soon as the machine is running, I get no display and 5 beeps (1 long, a follow-up of 4 short beeps). Each stick of RAM work well individually, and I also tested slot A and b. Thus, the 2 sticks of RAM are working alone and work the two slots. It seems that this machine has a problem with 2 sticks of RAM.

  The ACPI BIOS is up to date (v1.40). I also tried the old 256 MB stick with one of the new sticks of 512 MB - same problem. I tried this as the supplier of memory mentioned this Toshiba may take only 1 GB maximum.

  Any ideas why two sticks of RAM does not work?

  Thanks in advance and amicably.

  James

  Hello

  You are right. The laptop must be able to manage memory 1024Mo. (2 x 512 MB)
  Due to your description, I think that both modules are compatible, but cannot play together.
  In my opinion, you should use two modules with the same specifications

  Try to use the modules recommended by Toshiba;
  PC2100 256 MB (PA3127U - 1 M 25)
  PC2100 512 MB (PA3164U - 1 M 51)

• Satellite P20 does not see my router?

  Outside what is my 1st post, I am new to 'Wireless '. I thought all I had to do was flick my wireless light up, but no!
  My Mac connected instantly partners, and my laptop will not. I am trying to establish a connection with a Siemens Gigaset SE551 (which was given to us by our service provider).

  I tried all the instructions on a manual gave me more, I ran diagnostics etc. It's probably something really stupid that I forget... can anyone help?

  I have goggled a bit and discovered that the Siemens Gigaset SE551 router supports only the standard WLan 802.11 G.

  Please check what WLan standards are supported by you card Atheros WLan internal.
  We must define and support the 802.11 G, if you want to communicate with the router.

  As far as I know, you can see these settings in the WLan card properties.
  The properties you can find via-> made Device Manager right click on the WLan card-> properties

  As you have already said, you are a beginner then maybe you should ask someone with more experience WLan for assistance.

• I have a MBP Late 2013 will pair does not with 6s on Blutooth

  Read all comments (lots of old stuff on these communities) and tried all the suggestions of trashing the plist etc etc. Still unable to get my iPhone 6s to pair with my MBP end 2013.

  For a fleeting moment after that match it says connected not connected appears.

  AirDrop works, but my phone does not appear on the screen of the devices. If sending photos of the iPhone works well my avatar is not displayed as sender just my intials & where ever he gets the ints info not the name I use in my Contacts.

  Someone at - it any idea what is happening. This worked OK until recently.

  An iPhone will pair not via Bluetooth to a computer (Mac or Windows) with the exception of hotspot and then only if your cell phone plan he supports. See below for more information. https://discussions.Apple.com/docs/doc-7722

  If you try to use the procedure of transfer/continuity or AirDrop, which does not have Bluetooth but devices don't are NOT matched. Bluetooth must be just on and the devices within range of the other. The following may help in problems of transfer/continuity: https://support.apple.com/en-us/HT204678

• ASA does not propagate any routes for VPN users

  Good afternoon

  I m a problem concerning the spread of the roads to authenticated VPN users through the asa tunnel-group.

  I have a VPN-users-pool where my users receive their IP address, and after authentication and the tunnel is established the idea is that the user get to the networks defined in the following ACL:

  access-list within the standard allow 10.1.0.0 255.255.0.0

  access-list within the standard allow 192.168.15.0 255.255.224.0

  Now, the problem is that, after the tunnel is set up the only way, that the user receives is the default route (which is not supposed to be sent). The user does not receive the roads specified in the ACL list above. It has not received the network mask and assumes one 8 netmask (given that the pool of network from where it receives the IP address is a class A network).

  Network routing works as expected (when I add the static routes directly to PC users, everything works OK). It s just the matter of the ASA do not spread the roads as it should.

  Here is my split tunneling settings:

  attributes of Group Policy DefaultRAGroup

  VPN-idle-timeout 1

  Protocol-tunnel-VPN l2tp ipsec

  disable the PFS

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value inside

  (...)

  attributes of Group Policy DfltGrpPolicy

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value inside

  (...)

  Any ideas?

  I have apreciate your help

  Best regards

  Just a question, I see:

  attributes of Group Policy DefaultRAGroup

  Protocol-tunnel-VPN l2tp ipsec

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value inside

  internal DefaultRAGroup_1 group strategy

  attributes of Group Policy DefaultRAGroup_1

  Split-tunnel-policy tunnelspecified

  It looks like your policy

  DefaultRAGroup_1 you set ACLs and the other doesn't seem to be for L2TP/IPSEC. How do you connect to the ASA, using L2TP/IPSEC or Cisco IPSEC client? In addition, if your users are devoted to this group policy:

  DefaultRAGroup_1 it looks like the acl is missing for the split tunneling

• Active state with menu manual not working does not with child pages

  I created a horizontal menu manual on my master page with two links (at WORK and about me). I did them manually as it was the only way I could work out how the style and the menu items to distance as I wanted. I created an active state that works for the main page WORK and the about me page.

  However, I have four child pages under the work, but when you click on one of them that the active State for labor (a green line under work) does not appear. When I return to the menu options to try to "solve" the problem and choose "All pages" all child pages appear in the main menu I want and does not solve the problem. I chose manual that I could put the line to show that under the term of WORK and not all field.

  Here is my Web site to demonstrate the problem: www.robertgreens.com

  Any help to fix this would be appreciated with gratitude!

  I managed to solve this problem (with the help of Live Chat Support). I needed to create an autour work and provide a 'normal' State which resembled the active state, so when you click on the pages of the child, it looked like work page parent menu (with a green line) below. This meant that I had to duplicate master page and do the same (deletion of the green line in the menu of work) for the words Me page. And now, everything looks the same: www.robertgreens.com