Wrong color white balance correction

Similar Questions

• DSC-HX200V color white balance off

  I sent this service. I remembered the message board here, so I thought I would post it.

  I just bought a new DSC-HX200V 20/06/13. He spent the day 14 back. The colors are far from many times. White will look BRIGHT yellow, yellow will be white or green. It's little like he thinks it is in one of the modes of effect as vives/pop colors I've tried setting the WB '+' and it will help a little. I tried different modes of settings for the White Balance, i.e. the Sun, clouds, etc., but most of the time, it only gets worse. I tried "SET white balance," where you set it to something like the white paper. Which works fine until I turn it off and I have to re - set again once I turn it back on. (I'm NOT talking to different conditions, but just turn it off and on again in the same conditions.) Shouldn't it be adjusted to these conditions?

  BTW, I'm in Cape Coral, Fl 33990. Is it all local can I take it that it is verified?

  LeapingGnome

  Yes, it remains on the "One Push" when it turns back on... or whoever it is on when it is off.

  ("it could mean that you might have to re - calibrate the WB custom everywhere.")

  That wouldn't work too well asking time to stop so I can re - calibrate whenever it turns on.

  Check out my other post on ISO stuck and have to do a reset.

  About how long is the u-turn on sending in? Who pays for the shipping? I do not think go threw it on a device that is only 3 weeks. Being then without it.

  Thank you

  Leaping GNOME

• Basic white balance questions

  (1.) what do you do if you are working on an image that has absolutely no white or neutral colors? Maybe white detail is washed out, perhaps the image is composed of blues, reds and yellows. How to use the tool in this case white balance?

  2.) If you have the opportunity to choose both a white or gray color to use the white balance to the tool, is there a general rule for the use of one over the other? Or do you try just the two to see who is the most beautiful? Is it clicking on a white result in a code white balanced image better than when clicking on gray background?

  Thank you.

  An easy way to do this would be to highlight the two images and have active auto-sync.  Then when you click on the map of the white balance to get the white balance correction it would be automatically applied to the image to other institutions.  If you do not have auto-sync active you could highlight the two images later and use the sync button and choose only the white balance.  Another way would be to take note of the value of the white balance after you corrected with the map and simply enter the value in the other image.

  I forgot this forum, I've been in.  In ACR you just want to underline the two images assuming that they are both open in ACR, and then perform the white balance correction in that with the map.  If the two images are highlighted the correction will take place in the two images.  Sorry for the confusion.  The synhronize button works in the same way that I described earlier.

• any1 know how correct color for white balance/color category?

  Hey what's up guys just finished my 1st clip now I need 2 correct color & color grade. I willl be doing black and white video so told me I need 2 get rid of any color in my images. I 4got 2 set the the white balance on my 7 d when I was shooting sceens sum I can use any help possible as what is the best color to use checker or how my images white balance any help is greatly appreciated thank you.

  Check the basics and do a Google search. The first three listed will be videos, link following points to the Adobe Help files.

  The basic tools are the same as in Photoshop, but there are a bunch of 3 plug-ins third out there that make the job easier. If run you one of the tutorials found in your Google search and you're stuck back to us.

• Bridge CS5 applies wrong white balance during extraction of thumbnails (only for raw files)

  Hello to all the assistants of Adobe,

  Photographer welder here. I use a Canon T2i and I've been shooting raw with automatic white balance.

  After I downloaded the CR2 files to the bridge, bridge starts thumbnail extraction. It is then that the problem begins: I watch bridge thumbnail extraction photo after photo, turning them into white balance bad one by one. After the bridge is done, I open one of these photos in Camera Raw, it shows the picture in the "custom white balance". I could go back to "As Shot". But now, each Bridge photo has custom white balance and is difficult to bridge. This screenshot shows what looks like my bridge after thumbnail extraction...

  Yesterday, just out of curiosity, I took a few photos with the settings of the different on the camera white balance. I downloaded their bridge and bridge too wrote all the white balance settings. Then I imported the same pictures (from the same files) to iPhoto, they appear with writing correct balance. Please see the second screenshot.

  The third screenshot shows a unique photo that I opened the bridge to Camera Raw and the same photo, as it appears in iPhoto, the original two.

  

  Again, this only happens to CR2 files. All TIF, jpeg files are fine.

  Any ideas?

  Thank you!

  -Wolfie

  Any ideas?

  First of all, taken of view Raw has the advantage of the evolution of the color temperature (balance of Pentecost) to what ever you like everything you shot in camera.

  It seems once you have registered a custom default setting white balance and it is applied to each new file because you said bridge to do. The best way out of this is to open a raw file in ACR and the basic right tab you see a small icon (next to the base word) submenu. Click on it and the line select "Reset Camera Raw defaults" downstairs.

  Also decide if you want to stay in 16-bit mode (you're now as shown in the blue line under the preview). If you want the chance it to 8 bits, just click on this blue line and choose your options in this menu. Just do it once for that same camera files, ACR remembers the settings for you.

  Using 16-bit mode has advantages when the color corrections using critical (but you should also replace the ProPhoto color mode in my opinion). The downside is that the 16 bit doubles compared to 8-bit file size

  Having put default ACR should immediately make your thumbs by building of new inches and previews, but if not, you must choose purge the cache for the file from the menu Tools / cache / purge the cache for the file. Now the new settings will apply.

  It may take a while so let bridge do its job properly before starting other jobs in bridge (see the activity bar downstairs left to check if the bridge is still cached).

• Remove the cast/blue tint of JPG (setting the wrong while taking picture white balance)

  Hello

  Photosohop newb here with still CS3 (10.0), so please be patient.

  I was at a convention, there is not so long ago, I took a lot of pictures with my phone. I have noticed that in the House, that some of the photos came out with an intense blue cast because of a bad white balance setting (I must have accidentally changed).

  I tried to fix the image for the last 2 hours, without real success. I tried everything under Image-> settings-> "Auto color", "Levels of colors" and "Match Color", moving the sliders up and down to get the best match. The best I could come up with was still far from the other photos that I took the same day.

  This is one of the bad pictures: http://imgur.com/vw12aTQ

  And here is one I took a few minutes later with the 'normal' setting: http://imgur.com/RMFm7fo

  In fact, I had a pretty good game by cutting stones on the two photos and using "matches the color'-> 'Source', but I couldn't apply this technique to the overview.

  Could someone please help me to make the colors of the first image similar to the second?

  Thank you

  Roland

  Here is an easy solution...

  Choose the Image - adjust - curves, and then right-click the gray Point eyedropper and sample something in the picture that should be a neutral gray - say one of the rocks on the ground.  Click on in various places, until you like what you see.

  

  -Christmas

• RE: White Balance and color temperature

  Can we do the same kind of white balance, as we have in Photoshop Camera Raw, in Premiere pro?

  Also, we can change the color temperature in Premiere Pro?

  Thank you.

  Very few cameras RAW video format out of the box –, RED, Arri, BlackMagic.  There are no DSLR that can do it for the video, even if they probably all do for still images.

  That said, I understand that some Canon models can be made to the RAW video format with magic lantern was last updated, but I don't know how well these files would work in PP, as Adobe has no support for them.

• CP 1025: CP1025 wrong color or white pages after the first page

  Hello
  Our company have 3 cp1025 printers. 2 of them get a problem (almost at the same time) which can be described as follows:

  -printing wrong colors, colors are mixed, for example indeed black color prints blue and it is colorless. It doesn't go to the first page, in addition to pages only.
  -printing of blank pages. First page printed perfectly, more pages are blank.

  We do not find a problem. Tried to change the new drum unit, pilots, we are working on Win XP and Win 7. Can you say something about this problem?

  One problem was a dirty printer. It was full of dust of color toners. Once it has been disassembled and cleaned, print get to normal. It's a good lesson on the use of non-original toners, some of them was poor in quality and color of dust fell to the mechanisms of the printer.

• Automatic white balance didn't work - photos is proved very violet/pink everything - can you help me?

  I've been a photographer for these last years, and it's the first time I have encountered this problem. I shot an event for a couple (reception) and I didn't have my grey card, so I put my Canon 5 d mkII on the white balance automatic (shooting with a Canon 24-70 2.8 and a Sigma 85 1.4, if it helps). As you will see on the photos of two examples - photos taken in the conference hall was going well, but the Favorites of the event itself were surprisingly saturated. The room had a ton of very bright uplighting in purple and pink - the shooting was going on in the viewfinder, but once I got them in the LR4, there was an almost complete cast of violet/rose above it all. Adjustment of the balance of whites in LR for auto, tungsten, fluorescent - nothing has worked. Adjust the temporary sliders - only a little better. Reducing the vibrance and saturation has helped a little more, but I really find a solution! I can't afford to pay back their money, but if I can't find a decent solution, I'll do it. I want to give them the best possible color correction, but I'm pretty new to LR and I could use some help. Just to be clear, I'm not looking for a link to a tutorial on how to adjust the white balance - I read all the... I'm hoping by using someone who has experienced this same thing or can still offers advanced solutions that "try to set the sliders more» Thank you in advance!

  http://i.imgur.com/dCda964.jpg

  http://i.imgur.com/uGoEuiB.jpg

  This isn't a matter of White Balance, and you will not be able to adjust this image with the settings of white balance only - either behind closed doors or in Lr.

  You shot this photo in colored light, and the effect you looks as if you want a fancy color filter in front of your lens.

  I doubt if it can be adjusted to a 'normal' image looking at all. But for all its worth, here are the best I could come up with – even if I don't say it's THE best, in fact, it is still severely lacking.

  

  And here's screenshots of the settings I used. I found that the most promising "adjustments" were in the calibration Panel. If you play a little bit maybe there is a better solution.

  

  The image has a severe cast of purple, which is a red and blue combination. Increasing green will help. That is why I put the slider dyed in Basic-100.

  In the calibration Panel, I put the still green hue, reduces the saturation of red and blue and changed the shades. Finally, in HSL, I reduced the saturation of blue.

  PS: I think that the advice of Lee Jay is good. Create your own profile for counterweight in light color.

  Post edited by: web-Weaver: added PS

• How to set quickly animate image key/white balance

  I have the video of a procedure step by step of a House (a few minutes just to walk through and stealthily in each room).  There is the light of the Sun, incandescent, fluorescent and whatever else.  Looking at a white bathroom, everything appears yellow.  Similar problems with different casts in other areas.

  I have already created an adjustment layer to use the secondary color Correction in the three way color corrector to minimize the blue cast of the rays of the Sun.

  I would now like to move through the video and all few seconds, set a keyframe and adjust the white balance for this area, as quickly as possible.  It seems that there is not a way to animate the (?) white balance eyedropper, that would be the ideal.  All I see now is the sliders under color corrector quick, to the corner of the tint, the Balance magnitude and gain balance, which all can be animated.  Having to deal with all three of those would be a huge pain, I think.

  Any ideas?  Note that it doesn't have to be perfect, just rough.

  Instead of keyframes, make a cut.  Then add crossfades.

• In LR white balance selection tool

  just a general question here: when you use the pipette "white balance selector" tool in LR, is it actually to neutralize the grays in PS, i.e. through the pipette midtones in an adjustment of levels? just curious...

  No, LR White Balance controls and the pipette affect the tonal full (0-100%) will also. This is a global function for the correction of conditions of temperature color taken from view. For photos of the 'mixed' lighting, you can also use the Brush tool to paint on specific areas of color correction. It works very well.

• White balance - Plug in for adjustment

  I forgot to set on my camera white balance prior to registration.  I remember coming across an AE plugin effect that's going to set/adjust the white balance, but I don't remember that one is.

  Thank you

  CS4

  The button "Auto color" Color Finesse (provided with AE) will correct the white balance errors.

  The correction is based on the frame in progress, in order to choose an 'average' setting of white balance to.

  Bob Currier

  Synthesis

• DeskJet D2360: Deskjet 2360 - prints wrong colors, even if the test page seems well

  In 10 (64-bit) Windows, Deskjet D2360 prints the well test page, but the colors aren't any application (documents, photos...). Cyan looks like dark blue. Green also appears dark blue. I just updated the drivers from the HP website, but the behavior remains the same.

  The problem appeared after Windows 10 updates (January 2016 and later versions).

  Print and Scan Doctor couldn't fix it. Help!

  (Suggestion: If your printer prints the test page, why not propose an image file with what the test is supposed to look like.) This is useful especially to confirm colors. If I have a print test and see a few squares of color, how could I know if they are the correct colors?)

  After a long period of frustration, I found the non-professional magic solution:

  http://h30434.www3.HP.com/T5/inkjet-printing/printer-prints-wrong-colors-after-Windows-10-update/TD-p/5242565/highlight/false/page/3

  Print a test page with HP print and Scan doctor. Once the problem is resolved.

• white balance and other options change

  Hi, I've been away from taking pictures for awhile (focusing on FCP - X & videos). I've noticed recently that Apple has moved things from iPhoto to Photos. Whatever... My biggest concern is how I color balance and make the picture white balance? I've lived everywhere I thought it would be, but not luck. Can someone advise me on how to make these pictures? If this isn't the case, I can do them in iPhoto and continue to use it, or I don't expect too much from Apple?

  I always iPhoto V 9.6.1 addition Photos V 1.3

  If there are tutorials or somewhere you can direct me to know how to deal with this change, I would be very happy.

  see you soon,

  Jack

  Photos done editing capability than iPhoto.  However, you must go in the adjustment mode in the edit window and click on the button Add blue.  Then check all the items in the list:

  

  and click on Save as default down.  Now, you will have the following in the setting mode:

  

  The function address is in the mode of culture.

  

• Satellite Pro L650 series - the error screen white balance

  Hi all
  I use a Satellite Pro L650 series. When I use the laptop for several hours, my screen becomes bad white balance. In detail, the screen clears so dazzling with the strange white color. If I open a Web site, the pictures on the website becomes blurry images.
  If I put the screen in blue, she can't make easy the dazzling color, but if I put the screen in white or green and yellow, then it becomes abnormal colors and fuzzy.

  I have to restart my computer, and this problem can be solved.

  Is there anyone encounter this problem like me?
  Could you share to me what is the problem? and what is the solution for this problem?

  Thank you very much

  Hello

  Have you noticed this screen problem laptop with mains running or simply using the battery?

  I read about the problem of similar laptop screen which was related to the Intel display power saving technology.

  In this case, you could solve this disabling this feature. Go to Intel display panel - conservation power source/battery - power tab function - saving technology display and uncheck this option.