Similar Questions

• WRT150N... strike!

  I had a just chilling out WRT150N under my computer desk, and I just got a new laptop.  I go ahead and start to configure the router.  Now the router flashes the power and then led all other lights turn on and remain lit.  Then she rinses and repeats.  When I connect my office, he repeats the animation for connection/network address acquisition.  I can't launch the Firmware utility software that I was proposed to download for a manual installation of firmware.

  It does not receive enough stable to get the installation.  I have Windows XP Home Edition.  A note more: the router repeats this behavior with or without anything plugged. And Yes, I tried the reset and disconnect/reconnect solutions.  Nothing.

  Most likely, you already have a diffective unit. You can try to upgrade the router using tftp. That run. Place your router IP and the password. Browse to the location of the firmware. If it still does not work, check if your device is still under warranty. They will replace the routers with questions like that.

• First HP

  First turn off let me start by saying that it is great to finally see HP offering a SAE to compete with Nspire, I hope that the future will be bing versions Mac emulator and connectivity kit.

  My question relates to Solve where on the Nspire you can enter a formula that uses only variables, and solving solutions, a simple example could be to ohm's law, where Solve (u = r * i, i) would be exit r = u/i.

  a similar attempt on the first gives me Solve (0 = 0, 0) am I using Solve() harm, and is this possible on the first?

  Hi!, jj2005:

  Welcome to Forum!

  Go to display CASE, then type in...
  
  solve (your_equation, your-variable)

  Solve (u = j * r, j)

  Where... to the Ohm's law...

  u = voltage in VAC.

  j = intensity of current, in amperes.

  r = resistance in Ohms.

  It is, the answer... {u/r}
  
  ATTENTION:... 'i'... that is, for reserved (complex)... then use something else instead. You can use 'j' or the other.

• How can I get a digital WDT which includes all samples, not only that of the current stage of time...?

  See block labeled "digital data" in my attachment for reference. Currently, we can consider that the point of digital data for the current time step (it is removed before the following appears). However, I like it showed all the samples in the table as in the example that appears on this link under "digital waveform control":

  http://zone.NI.com/reference/en-XX/help/371361H-01/lvconcepts/fp_controls_indicators/

  Thanks a lot for your suggestions! I am new to Labview, so I appreciate your help.

  Hey westerman111,

  If you are looking to produce your display includes information of the previous steps of Solver solution, you'll need to buffer the previous data. How to implement this in a loop of Simulation of design by & control uses the Memory.vi under control design Simulation & > Simulation > utilities > Memory.vi. It will allow you to save previous information generated in the simulation for letter simulation environment.

  I've attached an example that should help you get started using the Memory.vi.

  I'd also sure that what you are trying to achieve is suitable for the control loop & Simulation. I know you said that you were new to LabVIEW, so I wanted to make sure that you went to sea in the right direction. Is there a particular reason, why you use the control loop & Loop Simulation instead of a standard time or a forum? The loop control design simulation & is unique in that it calculates the solution of a dynamic system to a no prescribed time and the ODE solver. It also provides tools to interact with the model you solve during execution. However, if you are looking for measurements (instead of the simulation of the dynamic model) and data acquisition I advise to use the standard features of LabVIEW.

  Here are a few useful references for the departure with the two LabVIEW Control Design and Simulation Module.

  Tutorial: Introduction to Simulation (Control Design and Simulation Module)

  http://zone.NI.com/reference/en-XX/help/371894G-01/lvsimhowto/sim_h_gs/

  Getting Started with LabVIEW

  http://digital.NI.com/manuals.nsf/WebSearch/ba2fb433a7940e7a862579d40070cc2c

• Cannot close the disc completely Session

  When I use the function write cd (Vista) with active file system. After this I add files to a cd/dvd. Then I did a right click on the CD/DVD drive and select "closed session" he showed the cd player only icon on the status panel but not show the State of the ball and can not completely closed this cd.

  (I have try a normal layer with DVD + R)
  Please help to solve solutions

  Thank you

  Hello Mack_guide,

  Thank you for your response back!

  When you try to close the session and advise you that it is not finished, what's happening?  Have you tried to eject the disc?  If so, have you tried to test this drive on a different computer?  Below he indicates that by default, Windows automatically when you eject the disc.  However, I just want to check what happens if you eject the disc.  Please let us know status.  Thank you!

  If you are burning a live file system disc, however, you must close the current session to be able to use the disc in another computer or player (by default, Windows does automatically when you eject the disc).

  Engineer James Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

• Get a new case and power supply for my HP Pavilion a6355.uk

  1. sound of the HP Pavilion a6355.uk

  2. Windows 7 Professional 64-bit

  3. no error message

  4. it is not a problem, but its had a new graphics card, new ssd, another hard drive, removed the 500 GB hard drive, and that's all I think.

  Hi, I want to get a new case and power supply for my office

  If I want is http://www.pcworld.co.uk/gbuk/antec-one-0-761345-15970-8-atx-full-tower-pc-case-black-13374257-pdt.h...

  The power I want is http://www.pcworld.co.uk/gbuk/zs650w-uk-zs-series-ocz-zs650w-uk-atx-psu-650w-11342059-pdt.html

  Is 650 Watt most the jury can take? I read somewhere that most can take is 650 watts.

  My only concern is that, how do you take the I/O shield? I've never done before.

  Yes, it will fit your card mother Μatx.

  PS > remember to toggle the toggle SOLVED / SOLUTION to the right of MY post/reply.

• SettingsActionItem / NavigationPane in TabbedPane initialization

  I'm having a problem to SettingsActionItem to work properly with dynamic creation of NavigationPanes located in a TabbedPane.

  The problem is that when I run the app, I create the first NavigationPane tab to the onCreationCompleted signal. If I then try to access the SettingsActionItem, I can't push more pages on the settings page.

  If I select another tab, I can push more pages on the settings page, even when I return to the first who would work the first time. There must be something with the initialization of the first NavigationPane.

  import bb.cascades 1.0
  
  // Include asset folders
  import "folder1"
  import "folder2"
  import "folder3"
  
  TabbedPane {
      id: tabbedPane
      showTabsOnActionBar: false
  
      // Set to first tab id
  
      property NavigationPane currentNavigationPane: oneNavPaneObject
  
      property OneNavPane oneNavPaneObject
      property TwoNavPane twoNavPaneObject
      property ThreeNavPane threeNavPaneObject
  
      // Attached Objects
  
      attachedObjects: [
          ComponentDefinition {
              id: settingsListPage
              source: "SettingsListPage.qml"
          },
          Sheet{
              id: infoSheet
              InfoPage {
                  id: infoPage
                  onDone: {
                      infoSheet.close();
                  }
              }
          },
          ComponentDefinition {
              id: oneNavPaneDefinition
              OneNavPane { }
          },
          ComponentDefinition {
              id: twoNavPaneDefinition
              TwoNavPane { }
          },
          ComponentDefinition {
              id: threeNavPaneDefinition
              ThreeNavPane { }
          }
      ]
  
      // Application Menu
  
      Menu.definition: MenuDefinition {
          id: menu
          actions: [
              ActionItem {
                  title: "Info"
                  imageSource: "icons/info.png"
                  onTriggered: {
                      // For InfoPage, we will use Sheet
                      infoSheet.open();
                  }
              }
          ]
          settingsAction: SettingsActionItem {
              imageSource: "icons/settings.png"
              onTriggered: {
                  // For Settings, we will use NavigationPane
                  var settingsListPageObj = settingsListPage.createObject();
                  Application.menuEnabled = false;
                  currentNavigationPane.push(settingsListPageObj);
              }
          }
      } 
  
      // Tabs
  
      Tab {
          id: oneTab
          title: qsTr("One")
          imageSource: "icons/one.png"
          onTriggered: {
              oneNavPaneObject = oneNavPaneDefinition.createObject()
              currentNavigationPane = oneNavPaneObject
              oneTab.content = oneNavPaneObject
          }
      }
      Tab {
          id: twoTab
          title: qsTr("Two")
          imageSource: "icons/two.png"
          onTriggered: {
              twoNavPaneObject = twoNavPaneDefinition.createObject()
              currentNavigationPane = twoNavPaneObject
              twoTab.content = twoNavPaneObject
          }
      }
      Tab {
          id: threeTab
          title: qsTr("Three")
          imageSource: "icons/three.png"
          onTriggered: {
              threeNavPaneObject = threeNavPaneDefinition.createObject()
              currentNavigationPane = threeNavPaneObject
              threeTab.content = threeNavPaneObject
          }
      }
      onCreationCompleted: {
          oneNavPaneObject = oneNavPaneDefinition.createObject()
          currentNavigationPane = oneNavPaneObject
          oneTab.content = oneNavPaneObject
      }
  }
  

  Solved: Solution was to define the active tab.

      onCreationCompleted: {
          oneNavPaneObject = oneNavPaneDefinition.createObject()
          currentNavigationPane = oneNavPaneObject
          oneTab.content = oneNavPaneObject
          tabbedPane.activeTab = oneTab
      }
  

• Update Server VC and 5.5 ESXi hosts to update 3 b (Build 3248547)

  I'm in vCenter Server 5.5 and 5.5 ESXi hosts.  Both are updated 3A, patched to version 201510001, which is the build 3116895.  I plan the upgrade of update 3 b (Build 3248547) and I'm a little confused on the question of SSLv3.

  I wonder if this point below ESXi55 U3b & VC 55U3b Known Issues applies to my config:

  ESXi does not automatically added to the inventory of the vCenter servers
  If you install an earlier version of vCenter Server and vSphere Update Manager for ESXi 5.5 updated 3B, then after the task of sanitation, ESXi does not automatically added to the VC inventory. Remediation process never gets done and ESXi State of connection in the VC inventory is presented as disconnected. Solution: When you restart ESXi after reorganization process is started, enable SSLv3 on ESXi (which is disabled by default). This will ensure that ESXi is added to the VC inventory automatically in minutes and sanitation as completed.

  If I'm reading things correctly, upgrade to vCenter Server to 3 b first and then upgrade the ESXi hosts, will avoid lost communication problems.  Can anyone confirm?

  It should be good if you update vCenter first.

  The problem is that pre - U3b vCenter 5.5 forces an SSLv3 connection when connecting to an ESXi host on port 443 (not the reverse). It does this, even if the host ESXi and vCenter SSL/TLS libraries actually support TLS 1.0 + since at least vSphere 4.0.

  So when you update one host to 5.5 U3b, the oldest vCenter again will try to force a connection SSLv3 that will fail, since SSLv3 has been disabled to the host. If you're updating vCenter, first of all, it will initiate a good TLS 1.0 + connection to more similar and updated hosts.

  Here is an explanation of the (pre - U3b) vCenter SSLv3 handshake behavior:

  Re: vCenter and host communication SSL v3

• How to adjust the timing of any effect in After Effects?

  I want to make a building bursting at a precise moment of my video (using the shatter plugin). However, when I add the effect, it does not seem to give me options to adjust the schedule. I think it has something to do with a stopwatch, but I don't know how to use the stopwatch thng.

  Help, please!

  Thank you

  If you type "burst" in aid of field research in the upper right of EI the first link takes you the After Effects / effects Simulation help page. If you click on the effect of brightness (the sixth link in the list) need you specific instructions for the glow effect where the strength and the RADIUS are explained in the first paragraph. There are also links to a bunch of tutorials and other resources for the effect. Further down, you will find a more detailed description of the controls Force 1 and 2 Force including the citation that Todd gave above.

  I'm not doubting that you gave a glance before replying, but too many people expect that everything in AE has a simple click and solve the solution. More read you, the more you use the tools and community resources, you will learn how things work and the best and faster you will become to your business. In fact, I spend about 2 hours a week, just read more stuff in the help files that I have not watched for a while, just to stand. I also use the search box in help in AE all the time to check other possible techniques used by others in the community of the AE. If you do this then you will become a better artist in less time. Relying on the forums of users for a click and solve solution won't do much to help you learn how to work the AE.

• OfficeJet 4500 Solution Center says "disconnected".

  I got this HP Officejet 4500 since last October and he has no problem, but something that came just earlier, I get this message on the solution Center HP saying that the printer is disconnected, but everything IS linked and it works.  Y at - it no adjustment I could do short of re - install the software?

  I was on the point to re - install the software but I ran my registry cleaner first, and that solved the problem.  Thanks for your comments.

• Solution Center HP says that my printer is disconnected?

  I have a newer desktop with Windows 7 running computer. My printer says it lack drivers but I did everything to update & it is supposed to be compatible with Windows 7, but in the center of HP Solution it says that the printer is disconnected again I can still print, scan, etc? What is the problem and how to fix it?

  kkrawz wrote:
  

  [snip my OS is Windows XP, so I downloaded the 2 HP for XP systems diagnostic utilities. Using HP diagnostic tools that I managed to solve the problem where the Solution Center software could not. It says to click a button "Accept as Solution" If the issue is resolved, but there is no key. I've looked everywhere.  I clicked the star of "Bravo."  [snip]

  Thank you for the kudo.  Only the author of a thread (or moderator) has the button "accept as a Solution.

• I have a HP 620 laptop computer and a printer OfficeJet 4500 wireless. I can print wireless, but when I go to HP for Solutions to scan a document, it tells me that the printer is disconnected.

  I have a HP 620 laptop computer and a printer OfficeJet 4500 wireless.  I can print wireless, but when I go to HP for Solutions to scan a document, it tells me that the printer is disconnected.  There is nothing I can do to Solutions of HP to recognize the printer.  What causes this problem?

  Hello

  As OEM HP is responsible for the good operation of the printer and their
  drivers provided. Check with HP support, their documentation online and
  drivers and ask in their forums.

  Good luck, you need to update or reinstall the latest driver.

  HP - OfficeJet 4500 Wireless - drivers<- set="" to="" your="" version="" of="">
  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?product=3986399&LC=en&cc=us&DLC=en&lang=en&cc=us

  HP - OfficeJet 4500 Wireless - support and troubleshooting
  http://h10025.www1.HP.com/ewfrf/wc/product?product=3986399&LC=en&cc=us&DLC=en&lang=en&cc=us

  HP support/troubleshooting & drivers
  http://welcome.HP.com/country/us/en/support.html

  Contact HP
  http://welcome.HP.com/country/us/en/contact_us.html

  HP forums
  http://h30434.www3.HP.com/PSG/

  =============================================

  The main issue is probably the drivers, but these can help:

  Add or remove a printer
  http://Windows.Microsoft.com/en-us/Windows-Vista/add-or-remove-a-printer

  Solve printer problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems

  Open the printer Troubleshooter
  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

  Find the manufacturer's Web site
  http://Windows.Microsoft.com/en-us/Windows-Vista/find-a-printer-manufacturers-website

  Find and install printer drivers in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/find-and-install-printer-drivers

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Solution Center says C7180 is disconnected

  Hi all..

  I have a C7180 in 1 connected via wired ethernet.

  I am running Win7 Ultimate 64-bit.

  Since almost new, HP Solution Center began by saying that the printer is disconnected.

  The printer is actually disconnected, because I can see the ink levels, and I can also print from within any application.

  I can't scan or fax via the central solution because he (Center solutiion) think that the printer is disconnected.

  I tried print and scan doctor and any other diagnostic tool, I found on the HP site.

  If I REINSTALL ALL of the HP software, this temproarily solves the problem back 1 hour at disconnected.

  Any help much appreciated.

  See you soon

  Hi MUSHASHI.

  Follow the steps below and let me know what happens?

  First step: clear temp directory

  1. Type %temp% term or search programs and files of field
  2. Select all the files in this folder, and then press the delete key to remove. If you receive a message that the file is in use, you will need to ignore this file (s).
  3. Proceed to step 2 below

  Second step: downloaded and extracted to your system:

  1 download the drivers and full software features

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=MP-76229-1&CC=US&DLC=en&LC=en&os=4063&Product=1153754&sw_lang=

  2. once the download is complete, double-click the file to extract the software.

  3. when the installation window opens, press the Cancel button to stop the installation

  4. tap folder in the race or search programs and files of field

  5. Locate and open the folder starting with 7z (example: 7zS2356)

  6. right click on the folder and select copy

  7. close this window and all open windows, and then in the Middle the desktop right click your mouse and select Paste. This will move the 7z folder on your desktop.

  8 open the 7z, that you just copied on your desktop

  9 open the Util folder

  10 open the CCC folder

  11. start the L4uninstall.exe

  12. once the uninstall is complete, restart the computer

  13. run disk cleanup from the tools Accessories\ system under all programs folder

  14. download and install the latest version of Adobe flash player

  http://www.Adobe.com/support/flashplayer/downloads.html

  15 open the 7z folder and then double-click the Setup.exe file that will be towards the bottom of the open window. Follow the instructions on the screen to reinstall your printer.

  Let me know if you are able to successfully install the software and driver and are able to print & scan?

• I installed Windows 8.1 and my printer as shows disconnected in the solution Center.

  I have a HP Officejet Pro 7580 using Windows 8.1. I installed Windows 8.1 and my printer as shows disconnected in the solution Center.

  I uninstalled the hp app and reinstalled. Solved the problem! Thank you.

• Harm my printer HP Solution Center is disconnected

  HP officejet 6000 cb051 windows vista 32-bit.  After the initial installation, I had a problem with the printer print an alignment page after printing ever.  My only support free call and they had me do a uninstall3, then reinstall used.  The printer prints very well now, without printing an alignment page after each print job.  But now the hp Solution Center says that my printer is disconnected.  I tried to turn it off, wait a while, then on again.  But it does not help.  This limit problem help I can get from the solution Center.  Help, please.  I'm a novice!

  susana1027

  I solved my problem!  Since I had just installed this printer, it had not occurred to me that there might be updates.  But there was.  I downloaded the updates and the problem was solved!