WRT160 - routing issues

Hello

I want to install a WRT160 to an existing network. I'm on Qwest with their DSL modem. My network router's network 10.0.0.0/16 Vyatta. I know that the 160 is a router (must have purchased access point instead, my fault), so I placed its IP address as 10.1.0.1. PC connect very well and have a good IP address of the DHCP server, but they cannot access the other subnet or on the internet.

I guess I need a static route added to my router Vyatta, right? If so, what would be this way?

Thank you.

Problem solved... model me! I had active rip. Once I disabled it, everything works! Sorry for the trouble.

Tags: Linksys Routers

cisco_asa_prob.jpg

Here the IP Configuration and the routing of the Barracuda firewall table:

screen_shot_2014-08 - 12_at_16.01.42.png

I have a route on the Barracuda NG to the 10.10.10.0/24 network VPN Client on eth0.

The 192.168.1.0/24 LAN I ping the Client comes with Client VPN 10.10.10.11 as it should. But I can't ping or access network resources in the local network for AnyConnected customer's PC that connected through the VPN.

Here is the config Cisco ASA:

 : Saved : : Hardware: ASA5505, 512 MB RAM, CPU Geode 500 MHz : ASA Version 9.2(2) ! hostname leela names ip local pool VPN-Pool 10.10.10.10-10.10.10.200 mask 255.255.255.0 ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 switchport access vlan 5 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.250 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address dhcp ! interface Vlan5 nameif dmz security-level 50 ip address 172.16.0.250 255.255.255.0 ! ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server 192.168.1.10 same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network obj_any subnet 0.0.0.0 0.0.0.0 object network VPN-Pool subnet 10.10.10.0 255.255.255.0 description VPN-Pool object network NETWORK_OBJ_10.10.10.0_24 subnet 10.10.10.0 255.255.255.0 access-list inside_access_in extended permit ip any any access-list inside_access_in extended permit ip object VPN-Pool any access-list dmz_access_in extended permit ip any any access-list global_access extended permit ip any any access-list outside_access_in extended permit ip any any pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 mtu dmz 1500 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 no arp permit-nonconnected nat (inside,dmz) source static any any destination static NETWORK_OBJ_10.10.10.0_24 NETWORK_OBJ_10.10.10.0_24 no-proxy-arp route-lookup inactive access-group inside_access_in in interface inside access-group outside_access_in in interface outside access-group dmz_access_in in interface dmz access-group global_access global route dmz 0.0.0.0 0.0.0.0 172.16.0.254 1 route inside 0.0.0.0 0.0.0.0 192.168.1.254 tunneled timeout xlate 3:00:00 timeout pat-xlate 0:00:30 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy server-type microsoft user-identity default-domain LOCAL aaa authentication enable console LDAP_SRV_GRP LOCAL aaa authentication http console LDAP_SRV_GRP LOCAL aaa authentication ssh console LDAP_SRV_GRP LOCAL aaa authentication serial console LOCAL http server enable 444 http 192.168.1.0 255.255.255.0 inside snmp-server location Vienna crypto ipsec ikev2 ipsec-proposal DES protocol esp encryption des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal 3DES protocol esp encryption 3des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES protocol esp encryption aes protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES192 protocol esp encryption aes-192 protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES256 protocol esp encryption aes-256 protocol esp integrity sha-1 md5 crypto ipsec security-association pmtu-aging infinite crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map inside_map interface inside crypto map dmz_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map dmz_map interface dmz crypto ca trustpoint ASDM_TrustPoint0 enrollment self subject-name CN=leela proxy-ldc-issuer crl configure crypto ca trustpoint ASDM_TrustPoint1 enrollment terminal crl configure crypto ca trustpool policy crypto ca certificate chain ASDM_TrustPoint0 quit crypto ikev2 policy 1 encryption aes-256 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 10 encryption aes-192 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 20 encryption aes integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 30 encryption 3des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 40 encryption des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 enable dmz client-services port 443 crypto ikev2 remote-access trustpoint ASDM_TrustPoint0 telnet timeout 5 no ssh stricthostkeycheck ssh 192.168.1.0 255.255.255.0 inside ssh timeout 30 ssh key-exchange group dh-group1-sha1 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.254-192.168.1.254 inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept dynamic-filter updater-client enable dynamic-filter use-database ntp server 192.168.1.10 source inside ssl trust-point ASDM_TrustPoint0 dmz ssl trust-point ASDM_TrustPoint0 inside webvpn enable dmz no anyconnect-essentials anyconnect image disk0:/anyconnect-macosx-i386-3.1.05170-k9.pkg 1 anyconnect image disk0:/anyconnect-win-3.1.05170-k9.pkg 2 anyconnect image disk0:/anyconnect-linux-3.1.05170-k9.pkg 3 anyconnect image disk0:/anyconnect-linux-64-3.1.05170-k9.pkg 4 anyconnect profiles AnyConnect_client_profile disk0:/AnyConnect_client_profile.xml anyconnect enable tunnel-group-list enable group-policy DfltGrpPolicy attributes default-domain value group-policy GroupPolicy_AnyConnect internal group-policy GroupPolicy_AnyConnect attributes wins-server none dns-server value 192.168.1.10 vpn-tunnel-protocol ikev2 ssl-client webvpn anyconnect profiles value AnyConnect_client_profile type user group-policy portal internal group-policy portal attributes vpn-tunnel-protocol ssl-clientless webvpn url-list none username tunnel-group AnyConnect type remote-access tunnel-group AnyConnect general-attributes address-pool VPN-Pool authentication-server-group LDAP_SRV_GRP default-group-policy GroupPolicy_AnyConnect tunnel-group AnyConnect webvpn-attributes group-alias AnyConnect enable tunnel-group Portal type remote-access tunnel-group Portal general-attributes authentication-server-group LDAP_SRV_GRP default-group-policy portal tunnel-group Portal webvpn-attributes group-alias portal enable! ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 ! prompt hostname context no call-home reporting anonymous hpm topN enable : end no asdm history enable

Can someone please help me solve this problem?

When I tried to solve this I didn't choose which interface the Packet Tracer?

The interface inside or DMZ interface? Inside, he says it will not work with the dmz but the error did not help me

Anyone here knows why it does not work?

screen_shot_2014-08 - 12_at_16.34.57.png

screen_shot_2014-08 - 12_at_16.33.06.png

Hello

Inside LAN is directly connected to the right firewall VPN... then I don't think you have to have the itinerary tunnele... can you try to remove the road tunnel mode and check.

entrance to the road that is static to achieve 10.10.10.11 as its display is correct...

Route by tunnel watch also with 255 administrative distance. I've never used that in my scenarios... lets see...

Concerning

Knockaert

WINDOWS WIRELESS ROUTER ISSUE 7

Have a new Toshiba Satellite with Windows 7. Unable to connect to my router Netgear N150 DGN1000 wireless modem. Works very well with the connection of the cable. Have an older Toshiba with Windows XP (SP3) and have no problem connecting to the router with the wireless feature. My iPhone connects to the router with the wireless. Have updated my drivers for the hardware wireless on my laptop. Always without success.
I see hundreds of reports of the same problem on the Web site.
Can anyone shed some light on this?

Post here instead, please: http://social.answers.microsoft.com/Forums/en-US/w7network/threads ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

Home wireless network connections cut - a router issue?

I have 2 PC:

1 desktop running XP (SP3) on a H61DE/S3 Asrock mobo and Intel G620 2.6ghz CPU. RAM = 2 x 2 GB.

2. laptop running Windows 7 + Intel i3 CPU

3 wireless router D-Link DSL-2680 =

The office is directly connected to the router via an ethernet cable wireless.

I created a wireless network which consists of my office and cell phones with the help of a USB and the XP Wizard on my desk. I then clicked on "Network Setup Wizard" in the Control Panel on my desktop (XP) and created the network connections.

When I boot-up the two machines, I can see and access the connections network of desktop and laptop.

HOWEVER, if I let the machines for a while and then come back, although I can see the icon for "DESKTOP" in my network places on my laptop, when I click the icon, the cursor looks like this market, but then an error window appears stating that it cannot find the device and I want to diagnose the connection. When I click YES, sometimes, it detects the OFFICE and sometimes it doesn't.

The same thing happens on the desktop when I click on the "PORTABLE computer" icon in "My Network places".

The strange thing is, when I try to connect via Start Menu / run / \\'IP address on the laptop or desktop, I can connect usually either to the PC.

The questions are

1 can you explain why I should b affected by these connection question - is this a problem of compatibility between window7 and XP?

2. what type of home network, maintained by the router or directly between the laptop and desktop computer without involving the router?

Thank you

I assume that the HOMEDESKTOP, in this case, XP is the master browser because it is physically connected to the router and it is this machine that I created the wireless network and local.

N ° master of domain is chosen in an election. All devices have an equal chance of being elected little matter how they are connected. (A domain controller can always win, but that's neither here nor there). The problem here is that the Win 7 machine doesn't listen to the broadcasts and therefore think that it is the only device on the network and therefore chooses himself as master of go. The XP machine is involved in a normal election except that the Win 7 machine does not participate because he is not listening. They both choose and for a while, you have two masters to browse. The only listening to computer (XP) finally gets tired of hearing machine Win7 and abandoned as a master browser. Win 7 becomes the only browser then, but it does not work because he doesn't listen to any computer on the network. You can check this by bringing a window prompt (start-> Run-> "cmd") and enter the command:
nbtstat - a HOMEDESKTOP
or
nbtstat - a ROMANLAP1-PC
If the targen computer thinks that he is a master of travel, you will see a line "__MSBROWSE__".

For some reason, keeping the folders "My Documents" opened on both machines maintained the connection for 15 hours that day.

Anyway that you can keep the active connection, the machines will partner with the other. Once a connection is idling, then it must re-establish contact and is when the master browser or a response of diffusion is necessary and the Win 7 machine is unresponsive.

Try following all the steps in the article according to which apply to your configuration:

"Networking of computers running different Versions of Windows"
<>http://Windows.Microsoft.com/en-us/Windows7/networking-home-computers-running-different-versions-of-Windows >

I don't think there is a firewall in itself, but the way Windows 7 manages 'Home' vs networks 'Public' that can do behave like a firewall and cause problems with firewall-like. Article states that ' the network location is a setting that allows Windows to automatically adjust security and other settings according to the type of network to which the computer is connected. " --they don't talk a firewall, but this is part of what makes a firewall...

HTH,
JW

Have 320n main router issues

I just successfully connected my Wag320n to my main router an Optus Sagem router, they are connected using adapter ethernet powerline with radio available on the two even if I can't access the menu of Wag320n wireless.

The Wag320n is implemented with DHCP, NAT and firewall, a static IP within the range of the same subnet address and main modem, I left the drop for PPOA (not sure you if this is the right setting to have), name and password are the same as the primary modem to connect to internet. I have two modems connected via lan port 4

Now, the problem I have is that if I tyr to connect to lan port 1 of the Wag320n is going red and stays red, I'm guessing is not supposed to happen but then I end up with only 2 lan ports to use for television, media players etc.

Can someone please tell me what I'm doing wrong?

Thanks in advance

If the configuration is LAN to LAN, you will not be able to access the router configuration page unless you unplug first of the first. It is because he will not have now a switch or a wireless access point and not a DHCP server more.

Cisco 850 routing issues

I am trying to configure a cisco 850 router but I can't do a ping to the outside world of Vlan1. show running-configLooks follow

Current configuration : 5563 bytes!! Last configuration change at 15:33:02 UTC Sat Aug 13 2016 by ciscoversion 15.2no service padservice timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname fw2.myfw.tld!boot-start-markerboot-end-marker!!logging buffered 51200 warnings!aaa new-model!!!!!!!aaa session-id commonwan mode ethernet!!!ip dhcp excluded-address 10.10.10.1ip dhcp excluded-address 192.168.1.1ip dhcp excluded-address 129.x.x.5!ip dhcp pool ccp-pool import all network 192.168.1.0 255.255.255.0 dns-server 8.8.8.8 8.8.4.4  default-router 192.168.1.1  lease 0 2!         !         !         ip domain name mydomain.tldip name-server 8.8.8.8ip name-server 8.8.4.4ip cef    no ipv6 cef!         !         !         !         crypto pki trustpoint TP-self-signed-1017650632 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-1017650632 revocation-check none rsakeypair TP-self-signed-1017650632!         !         crypto pki certificate chain TP-self-signed-1017650632 certificate self-signed 01  3082022B 30820194 A0030201 02020101 300D0609 2A864886 F70D0101 05050030   31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274   69666963 6174652D 31303137 36353036 3332301E 170D3135 30343037 31303536   30375A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649   4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 30313736   35303633 3230819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281   81008B15 A50BCE53 C1A10611 78247737 97E31A5D 653AF401 024B244B F96B48E0   0A1B41EE 16FBFDD1 46F2E1E2 1329D2C6 EEFBCF5B 217DE650 7D2729B0 266008F3   AC4565EA 53D7FA5B 35761F14 6FBDCFAC 24994667 CB0311A9 7FE25580 7D9564C3   BFE10A4A F5F57C4F C4E18EC9 19874BCA 03127F56 252D04B8 9465A23F FBB9045B   D9EF0203 010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603   551D2304 18301680 146EAE54 B0C95DC2 0561F596 BC47E94B EF80617E F9301D06   03551D0E 04160414 6EAE54B0 C95DC205 61F596BC 47E94BEF 80617EF9 300D0609   2A864886 F70D0101 05050003 81810014 F5B63E51 AD80D4A0 3230E94D 3D1BE457   5D7CF78D 3C911F32 C7238D24 4A8C84D5 D5D4F744 EA2FFD5C 4A40E7A1 A517BFE3   10CC6078 5F446A15 F60EA41E 08C688AF A7834485 0991C739 F3CA38FE CFAA31E2   C72031C1 BAEFA756 719E4903 705C98A7 E20CB004 6FC82D22 D4E62E0C DBA54481   F6A68B3D AA905352 DD76B19F CD4190        quit!         !         username cisco password 0 somepasswordusername admin privilege 15 secret 5 $1$JJZR$kw8yTTHkjUGKIfB8sQiyJ0!         !         controller VDSL 0 shutdown !         ip telnet source-interface Vlan1ip ssh port 2222 rotary 1ip ssh source-interface Vlan1ip ssh rsa keypair-name 1024!         !         !         !         !         !         !         !         !         !         !         !         interface ATM0 no ip address shutdown  no atm ilmi-keepalive!         interface Ethernet0 no ip address shutdown !         interface FastEthernet0 no ip address!         interface FastEthernet1 no ip address!         interface FastEthernet2 no ip address!         interface FastEthernet3 no ip address!         interface GigabitEthernet0 no ip address!         interface GigabitEthernet1 description PrimaryWANDesc_WAN interface ip address 129.x.x.5 255.255.255.0 duplex auto speed auto!         interface Vlan1 description $ETH_LAN$ ip address 192.168.1.1 255.255.255.0 ip helper-address 192.168.1.254 ip nat inside ip virtual-reassembly in ip tcp adjust-mss 1412!         ip forward-protocol ndip http serverip http access-class 23ip http authentication localip http secure-serverip http timeout-policy idle 60 life 86400 requests 10000!         !         ip dns serverip nat inside source list nat-list interface GigabitEthernet1 overloadip route 0.0.0.0 0.0.0.0 GigabitEthernet1!         mac-address-table aging-time 15no cdp run!         !         !         banner exec ^C% Password expiration warning.-----------------------------------------------------------------------

Cisco Configuration Professional (Cisco CP) is installed on this device and it provides the default username "cisco" for  one-time use. If you have already used the username "cisco" to login to the router and your IOS image supports the "one-time" user option, then this username has already expired. You will not be able to login to the router with this username after you exit this session.

It is strongly suggested that you create a new username with a privilege level of 15 using the following command.

username <myuser> privilege 15 secret 0 <mypassword>

Replace <myuser> and <mypassword> with the username and password you want to use.

-----------------------------------------------------------------------^C        banner login ^C-----------------------------------------------------------------------Cisco Configuration Professional (Cisco CP) is installed on this device. This feature requires the one-time use of the username "cisco" with the password "cisco". These default credentials have a privilege level of 15.

YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE  PUBLICLY-KNOWN CREDENTIALS

Here are the Cisco IOS commands.

username <myuser>  privilege 15 secret 0 <mypassword>no username cisco

Replace <myuser> and <mypassword> with the username and password you want to use.   

IF YOU DO NOT CHANGE THE PUBLICLY-KNOWN CREDENTIALS, YOU WILL NOT BE ABLE TO LOG INTO THE DEVICE AGAIN AFTER YOU HAVE LOGGED OFF.

For more information about Cisco CP please follow the instructions in the QUICK START GUIDE for your router or go to http://www.cisco.com/go/ciscocp -----------------------------------------------------------------------^C        !         line con 0 no modem enableline aux 0line vty 0 4 access-class 23 in privilege level 15 transport input telnet ssh!         scheduler allocate 60000 1000!         end

I am connected via the port console of the router and can ping the outside world only from port GigaEthernet1 whose IP address129.x.x.5

Clients that connect on VLan1 get IP addresses in the range of 192.168.1.0/24 and these clients can ping each other, the gateway that is 192.168.1.1 and the GigaEthernet1 that has the intellectual property129.x.x.5

What's not in this case? Any suggestion is appreciated the most.

@[email protected] / * /;

Thanks for your post. I had a look at your configuration, and it is great that you are a few short steps on your NAT is why it does not work. Please follow the steps below in order to get this work properly.

1. first of all, let us remove the old configuration NAT then back to a clean slate with the following commands.

no ip nat inside source list nat-list interface GigabitEthernet1 overloadclear ip nat translation *

2. now, we will create a list of access control allows for NAT traffic and create the new NAT statement for that tie together. * NOTE: If the version of IOS, you are running requires mask rather than generic then change 0.0.0.255 to 255.255.255.0.

access-list 100 permit ip 192.168.1.0 0.0.0.255 anyip nat inside source list 100 interface GigabitEthernet1 overload

3. the next step is to specify the logical role of the interfaces in question, whether they are 'inside' or ' outside'.

interface vlan1 ip nat inside exitinterface GigabitEthernet1 ip nat outside exit

4. Finally, save us the configuration and reload.

copy run startreload

After the unit is returned as a result of charging, please try again. In some cases - depending on the version of the IOS, you have to ping the outside world from a computer on the local network rather than just sourcing of the interface VLAN. Try this back and forth, and let me know how get you there. I can't wait to hear back.

Kind regards

Luke Oxley

Please evaluate the useful messages and mark the correct answers.

routing issue 1131

Hello everyone.

Is there an example configuration that I could use to find my routing on my 1131 problem?

It is running in standalone mode and I can connect my wireless laptop to the network very well. A 3550 provides the DHCP service.

But once I try to access a different VIRTUAL LAN or try to go to the Internet, my Installer fails. Summer pulling on my hair to this day. Hope, that an example configuration will help me. Thanks in advance.

AIR 1131AG is a core 2 device that cannot make the originating routing layer or Layer 3 Protocol. Please be specific as to what you are doing.

DeskJet 3510 power after changing on my old router issues

I have my printer put in place via my wireless router secure that my desktop computer is connected to my router via an Ethernet cable. I have my HP printer software installed on my desktop as well as my wifes laptop, which is also connected by a secure wireless connection. I recently had to swap our router for a new one... After doing and connection all save our printer begins to feed oneself off the coast from which it has never done before. All solutions?

I thought about it... slap my forehead... she needs to get somehow in mode "Auto-off" when I refresh my new info of routers on the Desktop & laptop.

Client VPN routing issue

I am trying to configure client vpn software ver 5.0 for remote to connect to the local network behind a 1801 users.

I can get the client saying its connected but traffic is not circulate outside in:

When I try to ping an address 192.168.2.x behind the 1801 I get a response from the public ip address but then when I try to ping to another address I have no answer.

I guess the question is associated with NAT.

Here is my config, your help is apprecited

horodateurs service debug datetime msec

Log service timestamps datetime msec

encryption password service

!

host name C#.

!

boot-start-marker

boot-end-marker

!

enable password 7 #.

!

AAA new-model

!

AAA authentication login userauthen local

AAA authorization groupauthor LAN

!

AAA - the id of the joint session

!

IP cef

!

IP domain name # .local

property intellectual auth-proxy max-nodata-& 3

property intellectual admission max-nodata-& 3

!

Authenticated MultiLink bundle-name Panel

!

username password admin privilege 15 7 #.

!

crypto ISAKMP policy 3

BA 3des

preshared authentication

Group 2

!

ISAKMP crypto client configuration group 1801Client

key ##############

DNS 192.168.2.251

win 192.168.2.251

field # .local

pool VpnPool

ACL 121

!

Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

!

Crypto-map dynamic dynmap 10

Set transform-set RIGHT

!

map clientmap client to authenticate crypto list userauthen

card crypto clientmap isakmp authorization list groupauthor

client configuration address map clientmap throwing crypto

client configuration address map clientmap crypto answer

10 ipsec-isakmp crypto map clientmap Dynamics dynmap

!

Archives

The config log

hidekeys

!

property intellectual ssh time 60

property intellectual ssh authentication-2 retries

!

interface FastEthernet0

address IP 87. #. #. # 255.255.255.252

IP access-group 113 to

NAT outside IP

IP virtual-reassembly

automatic duplex

automatic speed

clientmap card crypto

!

interface BRI0

no ip address

encapsulation hdlc

Shutdown

!

interface FastEthernet1

interface FastEthernet8

!

ATM0 interface

no ip address

Shutdown

No atm ilmi-keepalive

DSL-automatic operation mode

!

interface Vlan1

IP 192.168.2.245 255.255.255.0

IP nat inside

IP virtual-reassembly

!

IP pool local VpnPool 192.168.3.200 192.168.3.210

no ip forward-Protocol nd

IP route 0.0.0.0 0.0.0.0 87. #. #. #

!

!

no ip address of the http server

no ip http secure server

the IP nat inside source 1 interface FastEthernet0 overload list

IP nat inside source static tcp 192.168.2.251 25 87. #. #. # 25 expandable

Several similar to the threshold with different ports

!

access-list 1 permit 192.168.2.0 0.0.0.255

access-list 113 allow host tcp 82. #. #. # host 87. #. #. # eq 22

access-list 113 permit tcp 84. #. #. # 0.0.0.3 host 87. #. #. # eq 22

access-list 113 allow host tcp 79. #. #. # host 87. #. #. # eq 22

access-list 113 tcp refuse any any eq 22

access-list 113 allow host tcp 82. #. #. # host 87. #. #. # eq telnet

access-list 113 permit tcp 84. #. #. # 0.0.0.3 host 87. #. #. # eq telnet

access-list 113 allow host tcp 79. #. #. # host 87. #. #. # eq telnet

access-list 113 tcp refuse any any eq telnet

113 ip access list allow a whole

access-list 121 permit ip 192.168.2.0 0.0.0.255 192.168.3.0 0.0.0.255

access-list 121 allow ip 192.168.3.0 0.0.0.255 192.168.2.0 0.0.0.255

!

control plan

!

Line con 0

line to 0

line vty 0 4

transport input telnet ssh

!

end

you have ruled out the IP address of the customer the NAT pool

either denying them in access list 1

or do road map that point to the loopback address as a next hop for any destent package for your pool to avoid nat

first try to put this article in your access-lst 110

access-list 110 deny 192.168.2.0 0.0.0.255 192.168.3.0 0.0.0.255

access-list 110 permit 192.168.2.0 0.0.0.255 any

sheep allow 10 route map

corresponds to the IP 110

remove your old nat and type following one

IP nat inside source overload map route interface fastethernet0 sheep

rate if useful

and let me know, good luck

RVS4000 / WRVS4400 VPN routing issue.

I would like to simplify my installation a bit, but unfortunately I do not know how to do this.

I have a triangle of CSB RVS, 2 RVS4000, 1 WRVS4400 devices

each router has a VPN gateway to gateway with 2 others, to any one of the 3 sites, you can access resources on the other 2.

It also works well, if for some reason, one of the legs of the VPN breaks down, it passes through the other router. at least it seems to work that way when it is tested.

Now enter my problem. I have 2 laptops that go around, Mine and at the office. If any of these are off site and connect to a router via the QuickVPN client. they can see the resources on the router, to which they connect.

How would I be able to connect to the Router 1 and be able to access resources on other VPN routers ' ed?

It is not so much a problem on the router because it is on the QuickVPN. When you go to an IP address that is not on the local network from the router, the QuickVPN does not and it that the request is sent to the internet.

The only way to access the other site and resources would be to unplug the first router and connect to each other.

ASA 5510 routing issue.

Forgive me if this get confused.

I have a new ASA 5510, I set it up to use VPN. I can via IPSEC vpn and connect to 2 of my et.64 sous-reseaux.0 (we have 4 subnets in our range) I can ping, http, connect to the shares, SSH, etc. I use the ACL of our outgoing VPN module, so I have nothing here should be bad. The problem I have is learning to our network of laboratories located on the sous-reseau.128. I can't ping, connect, http anything.

Is there some special routing I need to do so that people that VPN in to see this subnet? (For test purposes the ASA is located behind the firewall and connected directly to the sous-reseau.0 so I know this isn't the firewall and everything else on that subnet can see our lab).

Thanks for helping on the new guy.

Shawn

Shawn-

Your sous-reseaux.0 &.64 is considered to be "interesting traffic" (by an ACL) and they are not NAT had sent through the VPN tunnel. You must add the sous-reseau.128 two the ACL that says no NAT and that specifies traffic interesting. If you encounter some snags, post a sanitized config and we will be able to give a more detailed response.

HTH

routing issues

I have a 2 501 s PIX. PIX - 1 has inside of the interface on the 192.168.x.0 and PIX - 2 a network inside the on the 10.0.x.0 network and external interface on the 192.168.x.2 that are the two internal lans. I need to configure a route to 192.168 to the 10.0 that I added a route to the config I thought that it would reach, but when I try to telnet to the 192.168 to the 10.0 I get an error in syslog, indicating that a road to 10.0.x.100 is not 192.168.x.10. This error comes from PIX - 1 What follows is the config of PIX - 1

Result of the firewall command: "sh run".

: Saved

:

6.3 (4) version PIX

interface ethernet0 car

interface ethernet1 100full

ethernet0 nameif outside security0

nameif ethernet1 inside the security100

activate the encrypted password of XXXX

passwd encrypted XXXX

PIX-1 hostname

domain nexstore.internal

fixup protocol dns-length maximum 512

fixup protocol ftp 21

fixup protocol h323 h225 1720

fixup protocol h323 ras 1718-1719

fixup protocol http 80

fixup protocol rsh 514

fixup protocol rtsp 554

fixup protocol sip 5060

fixup protocol sip udp 5060

fixup protocol 2000 skinny

fixup protocol smtp 25

fixup protocol sqlnet 1521

fixup protocol tftp 69

names of

name 192.168.x.0 Remote_PIX_Corporate

access-list 101 permit tcp any host 216.xx.xx.70 eq https

access-list 101 permit tcp any host 216.xx.xx.70 eq 3389

access-list 101 permit everything all unreachable icmp

access-list 101 permit icmp any one time exceed

access-list 101 permit icmp any any echo response

access-list 101 permit tcp any host 216.xx.xx.71 eq pcanywhere data

access-list 101 permit tcp any host 216.xx.xx.71 eq 5632

access-list 101 permit tcp any host 216.xx.xx.71 eq https

inside_outbound_nat0_acl ip access list allow any 10.x.0.96 255.255.255.224

outside_cryptomap_dyn_20 ip access list allow any 10.x.0.96 255.255.255.224

nexstore_splitTunnelAcl Remote_PIX_Corporate 255.255.255.0 ip access list allow one

pager lines 24

opening of session

recording of debug trap

host of logging inside the 192.168.x.10

Outside 1500 MTU

Within 1500 MTU

IP address outside 216.xx.xx.66 255.255.255.240

IP address inside 192.168.x.1 255.255.255.0

alarm action IP verification of information

alarm action attack IP audit

IP local pool remote_IP 10.x.0.100 - 10.x.0.119

PDM location 192.168.x.10 255.255.255.255 inside

PDM location 192.168.x.12 255.255.255.255 inside

PDM location 192.168.x.11 255.255.255.255 inside

location of PDM Remote_PIX_Corporate 255.255.255.0 outside

PDM location 10.0.x.100 255.255.255.255 inside

PDM location 10.0.x.0 255.255.255.0 inside

PDM logging 100 information

history of PDM activate

ARP timeout 14400

Global 1 interface (outside)

NAT (inside) 0-list of access inside_outbound_nat0_acl

NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

static (inside, outside) tcp 216.xx.xx.70 https 192.168.x.12 https netmask 255.255.255.255 0 0

static (inside, outside) tcp 3389 3389 netmask 255.255.255.255 192.168.x.12 216.xx.xx.70 0 0

static (inside, outside) 216.xx.xx.71 tcp pcanywhere-data 192.168.x.11 data pcanywhere netmask 255.255.255.255 0 0

static (inside, outside) tcp 216.xx.xx.71 192.168.x.11 5632 5632 netmask 255.255.255.255 0 0

static (inside, outside) tcp 216.xx.xx.70 3390 192.168.x.11 3389 netmask 255.255.255.255 0 0

static (inside, outside) 216.64.81.71 tcp https 192.168.x.11 https netmask 255.255.255.255 0 0

Access-group 101 in external interface

Route outside 0.0.0.0 0.0.0.0 216.xx.xx.65 1

Route inside 10.0.x.0 255.255.255.0 192.168.x.2 1

Route inside 10.0.x.100 255.255.255.255 192.168.x.2 1

Route inside 192.x.x.0 255.255.255.0 192.168.x.3 1

Timeout xlate 0:05:00

Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

Timeout, uauth 0:05:00 absolute

Console timeout 0

Terminal width 80

Cryptochecksum:XXXXX

: end

In theory, what you say is correct, but in reality it does not happen. Because the Pix won't send it back on the same interface.

192.168.x.10 traffic goes to Pix1 has the road to 10.0.x.0 via 192.168.x.2 (off-Pix2) when the pix gets what he does not know the package because it violates the concept of security of the Pix.

He would do any 'router '... If you are looking for cheap, Linux box, Linksys, * shudder * Windows.

Newbie Help Needed: Cisco 1941 router site to site VPN traffic routing issue

Hello

Please I need help with a VPN site-to site, I installed a router Cisco 1941 and a VPN concentrator based on Linux (Sophos UTM).

The VPN is established between them, but I can't say the cisco router to send and receive traffic through the tunnel.

Please, what missing am me?

A few exits:

ISAKMP crypto to show her:

isakmp crypto #show her

IPv4 Crypto ISAKMP Security Association

DST CBC conn-State id

62.173.32.122 62.173.32.50 QM_IDLE 1045 ACTIVE

IPv6 Crypto ISAKMP Security Association

Crypto ipsec to show her:

Interface: GigabitEthernet0/0

Tag crypto map: QRIOSMAP, local addr 62.173.32.122

protégé of the vrf: (none)

local ident (addr, mask, prot, port): (192.168.20.0/255.255.255.0/0/0)

Remote ident (addr, mask, prot, port): (192.168.2.0/255.255.255.0/0/0)

current_peer 62.173.32.50 port 500

LICENCE, flags is {origin_is_acl},

#pkts program: encrypt 0, #pkts: 0, #pkts digest: 0

#pkts decaps: 52, #pkts decrypt: 52, #pkts check: 52

compressed #pkts: 0, unzipped #pkts: 0

#pkts uncompressed: 0, #pkts compr. has failed: 0

#pkts not unpacked: 0, #pkts decompress failed: 0

Errors #send 0, #recv 0 errors

local crypto endpt. : 62.173.32.122, remote Start crypto. : 62.173.32.50

Path mtu 1500, mtu 1500 ip, ip mtu IDB GigabitEthernet0/0

current outbound SPI: 0x4D7E4817 (1300121623)

PFS (Y/N): Y, Diffie-Hellman group: group2

SAS of the esp on arrival:

SPI: 0xEACF9A (15388570)

transform: esp-3des esp-md5-hmac.

running parameters = {Tunnel}

Conn ID: 2277, flow_id: VPN:277 on board, sibling_flags 80000046, crypto card: QRIOSMAP

calendar of his: service life remaining (k/s) key: (4491222/1015)

Size IV: 8 bytes

support for replay detection: Y

Status: ACTIVE

Please see my config:

crypto ISAKMP policy 1

BA 3des

md5 hash

preshared authentication

Group 2

encryption... isakmp key address 62.X.X... 50

ISAKMP crypto keepalive 10 periodicals

!

!

Crypto ipsec transform-set esp-3des esp-md5-hmac TS-QRIOS

!

QRIOSMAP 10 ipsec-isakmp crypto map

peer 62.X.X set... 50

transformation-TS-QRIOS game

PFS group2 Set

match address 100

!

!

!

!

!

interface GigabitEthernet0/0

Description WAN CONNECTION

62.X.X IP... 124 255.255.255.248 secondary

62.X.X IP... 123 255.255.255.248 secondary

62.X.X IP... 122 255.255.255.248

NAT outside IP

IP virtual-reassembly in

automatic duplex

automatic speed

card crypto QRIOSMAP

!

interface GigabitEthernet0/0.2

!

interface GigabitEthernet0/1

LAN CONNECTION description $ES_LAN$

address 192.168.20.1 255.255.255.0

IP nat inside

IP virtual-reassembly in

automatic duplex

automatic speed

!

IP nat pool mypool 62.X.X... ... Of 122 62.X.X 122 30 prefix length

IP nat inside source list 1 pool mypool overload

overload of IP nat inside source list 100 interface GigabitEthernet0/0

!

access-list 1 permit 192.168.20.0 0.0.0.255

access-list 2 allow 10.2.0.0 0.0.0.255

Note access-list 100 category QRIOSVPNTRAFFIC = 4

Note access-list 100 IPSec rule

access-list 100 permit ip 192.168.20.0 0.0.0.255 192.168.2.0 0.0.0.255

access-list 101 permit esp 62.X.X host... 50 62.X.X host... 122

access list 101 permit udp host 62.X.X... 50 62.X.X... host isakmp EQ. 122

access-list 101 permit ahp host 62.X.X... 50 62.X.X host... 122

access-list 101 deny ip any any newspaper

access-list 110 deny ip 192.168.20.0 0.0.0.255 192.168.2.0 0.0.0.255

access-list 110 permit ip 192.168.20.0 0.0.0.255 any

!

!

!

!

sheep allowed 10 route map

corresponds to the IP 110

The parts of the configuration you posted seem better than earlier versions of the config. The initial problem was that traffic was not in the VPN tunnel. That works now?

Here are the things I see in your config

I don't understand the relationship of these 2 static routes by default. It identifies completely the next hop and a mask the bytes of Middleweight of the next hop. Sort of, it seems that they might be the same. But if they were the same, I don't understand why they both make their appearance in the config. Can provide you details?

IP route 0.0.0.0 0.0.0.0 62.X.X... 121

IP route 0.0.0.0 0.0.0.0 62.172.32.121

This static route implies that there is another network (10.2.0/24) connected through the LAN. But there is no other reference to it and especially not for this translation. So I wonder how it works?

IP route 10.2.0.0 255.255.255.0 192.168.20.2

In this pair of static routes, the second route is a specific subnet more and would be included in the first and routes for the next of the same break. So I wonder why they are there are. There is not necessarily a problem, but is perhaps something that could be cleaned up.

IP route 172.17.0.0 255.255.0.0 Tunnel20

IP route 172.17.2.0 255.255.255.0 Tunnel20

And these 2 static routes are similar. The second is a more precise indication and would be included in the first. And it is referred to the same next hop. So why have the other?

IP route 172.18.0.0 255.255.0.0 Tunnel20

IP route 172.18.0.0 Tunnel20 255.255.255.252

HTH

Rick

Remote vpn routing issue

Hi, please find the attachment.

I want remote access client vpn server that connect you to my ASA 5510 outside interface.

Is this possible via the static route set or something else?

Thank you very much!!!

Hello

There is not enough information to give a good answer. This should be possible, but your level ASA software firewall and VPN Client configurations factor in this also.

If you have a customer VPN Split Tunnel configuration, then you must add a rule to the existing ACL and say the IP address of the server. If you use Client VPN full Tunnel while you don't have to worry about the same thing only with Split Tunnel.

Then you will probably need the configuration "permit same-security-traffic intra-interface" so that traffic can enter the 'outside' and leave 'outside' to the server. It won't work without the mentioned order.

You will also need a PAT Dynamics example

If you use a software 8.2 or below and have this dynamic PAT defect for LAN users

Global 1 interface (outside)

NAT (1 x.x.x.x y.y.y.y inside)

Then for the Pool of Client VPN you can add this

NAT (outside) 1 20.20.20.0 255.255.255.0

More often, this should be sufficient to allow the traffic to arrive on the VPN Client user ASA and out of 'outside' interface and head to the server.

Hope this helps

Don't forget to mark the reply as the answer if it answered your question.

-Jouni

VPN routing issues...

Here's my problem, with a bit of luck can someone help...

I use the Cisco client to establish a connection with a client. Once the connection is established that I can navigate is more on my local network. Here are the results of the command ipconfig for the local card and the VPN adapter.

Any help would be greatly appreciated.

Windows IP configuration

Name of the host...: nvcadmin06

Primary Dns suffix...:

... Node type: unknown

Active... IP routing: No.

Active... proxy WINS: No.

Ethernet connection to the Local network card:

The connection-specific DNS suffix. :

... Description: Broadcom NetXtreme 57xx Gigabit Controller

Physical address.... : 00-18-8B-00-5C-B1

DHCP active...: No.

... The IP address: 10.20.0.5

... Subnet mask: 255.0.0.0.

... Default gateway. : 10.0.0.1.

DNS servers...: 10.0.0.1.

208.67.222.222

Ethernet connection to the network space 2 card:

The connection-specific DNS suffix. :

... Description: Cisco Systems VPN card

Physical address.... : 00-05-9A-3C-78-00

DHCP active...: No.

... The IP address: 10.10.10.197

... Subnet mask: 255.0.0.0.

... Default gateway. :

DNS servers...: 192.168.2.19

Thank you in advance.

Hi Eric,.

Unfortunately not, this is controlled by the VPN server.

You can try changing the routing on your machine by using static routes, but it is not supported, because it is considered a security risk.

I would recommend you to communicate with the remote administrator and explain that you must "split tunneling" instead of "tunnelall".

Thank you.

Portu.

Please note all useful posts