WRT300N router with Modem ADSL AM200

Similar Questions

• router with modem?

  Hello!

  I can use some help to configure my linksys EA3500 for my new ISP. My original ISP had a simple modem only had a port of the plugged into the internet port on the linksys router, did not provide for DHCP, none of that. It was just a modem.

  The new modem that I got by the new ISP also has complete router features, but I preferred to continue using the linksys for the 5 GHz wifi router. If the installer of the ISP just plugged one of the ethernet ports of the modem to the port of the linksys router and said that I would be good to go.

  Intermittent problems started out with dramatic slowdowns and disconnects when I was trying to stream the content or simply use internet on my laptop. At first, I thought the problem with the new modem or your ISP, but the internet was working fine if I connected directly to the new modem via its own wifi. Finally, I came to the conclusion that it was active on both DHCP servers the modem and routers linksys was the origin of the problem, so I put the router linksys in Bridge mode, and things have worked quite well since then. This still confuses me, because I don't think there will be problems with the router modems and functions of router from linksys being lit, until the modem is plugged into the internet port on the linksys router.

  Anyway, using the bridge mode on the linksys router means I lost the ability to use functions such as 'prioritization of media. " I would like to put in "automatic configuration - dhcp" mode so I can access this feature, but I need help understanding and preventingt him from apparent problems between the modem and the router. Ideally, I would like to use the wifi modem and wifi router on the same subnet, similar to its operation when the linksys router is in bridge mode, but I don't know how to do this and still have access to the "hierarchy of the media" features on the linksys router.

  Thanks for all advice :-)

  @jworkm. What is the model number and the IP address of the new modem/router? Probably a problem of conflict of IP. When you say, "I would like to use the wifi from the modem and the router on the same subnet wifi", do you mean you want the modem and the router to give IP addresses on the same range? If Yes, you can mount cascade the router via LAN to LAN, however, you will need to disable the DHCP on your EA3500. To learn more about cascading routers, click here.

  Kind regards

  Ethel_10700

  Linksys technical support

• RV042 with Modem ADSL installation

  We have to implement our DSL modem in Bridge mode to allow static IP of the router be seen on the outside for VPN configuration.  When we configure the modem in this mode, the router does not seem to offer a way to enter the user information and password; the internet connection does not work.   I don't know exactly what happens here... the router should do the login or the modem should it?  When the modem is configured as a bridge, I can connect to the internet via a computer connected directly to the modem (PPPoE) where the computer gives the user and password information.

  The router will do PPPoE.  In the configuration of the router tab, change the static to PPPoE.  If you have a static IP service, then use the static IP address instead.  The only available for configuration of VPN tunnel IP address will be assigned by PPPoE, or if you have a static service, he will be the one assigned to you.

• WRT160N with Modem Zoom ADSL X 6

  I hope someone can help.  I struggled my wireless home network with my camera WVC54GCA and new HP AIO wireless printer, dropped from the network.  My PS3 occasionally loses connection.  I am currently using the Zoom X 6 DSL wireless with.  I am wanting to abandon the use of the wireless router internal of the X 6 and go for a WRT160N.

  I guess the Zoom X 6 would plug into the Internet port on the back of the Wrt160N.  But now I have two routers to fight on the port forward and which do not.  So, how would I put it so I don't have to worry about a routers transmitting?

  My thought process would be to go to the Zoom X 6 bridge and DMZ address Linksys WRT160 gateway.  That should open the Zoom in the world.  Then, I would use the Linksys forwarding tables to manage these ports in need.  As the WVC54GCA who need some open ports.

  Am I wrong here?  I know that my signals have abandoned cannot be my setup as my X 6 is not near a source of EMI, I'm on a channel with little activity and my cordless phones are in the range of 5.6 Gig rather than 2.4 Gig.  And I assign IP addresses to each device above the DHCP range.  They all connect very well when I reboot the modem.

  Thanks in advance for anyone who can at least establish a road map if I have it all wrong.

  Kind regards

  Scott

  Due to lack of support in obtaining this router to forward ports to the Internet when it is used with a router dsl/modem connected to the WAN/INTERNET port, I decided to get this router for a refund.  Now if Linksys would release only their modem/router DSL for the American market, the headaches would cease.

  I really think that Linksysneeds to get tech support easier by some of their agents who participate in these forums.

• Modem/wireless router with USB port

  Qwest (my IP) told me that there is nothing like a modem/router with a USB port.  Am I crazy or what?

  Karibou

  Hello
  Welcome to the HP Forum!

  Karibou wrote:

  Qwest (my IP) told me that there is nothing like a modem/router with a USB port.  Am I crazy or what?

  Qwest is wrong. There are a number of manufacturers that make routers wireless with USB ports. This is a new trend.

  D - Link makes this one. Unfortunately, it has been abandoned. Linksys makes this one.

  Belkin makes one in this video.

• Encryption advice please WRT160N router/gateway/modem wireless

  I would like clarification on security and encryption please.

  I have a WRT160N router/gateway/modem wireless with WPA security is enabled.  I have a wired office with LELA installed and a wireless laptop.  A key is required when connecting the laptop but on page properties in LELA, it says "wireless encryption - no ' is this extra encryption in addition to the security theWPA. WH n I try to enable it, LELA asks the password admin but after entering that does nothing (except once again ask!)  What I am doing wrong?

  Thank you

  That your network is already reached, but him dosent software LELA display you something on your safety. This means that the LELA was not able to properly synchronize with the router and its wireless settings. So in this case, you do not have to worry about this, if you want you can uninstall and reinstall the LELA software on your computer, that might solve the problem. Or of another Complitely uninstall LELA software from your computer.

• When I try to connect with my wireless laptop will connect only to Local access. If I connect the laptop to the router with the ethernet cable, it works very well.

  VIsta - Local access only

  HI -.
  I recently moved.   I use the same router from my old apartment and I had no problem connection in the past.   Since I moved I have a new Time Warner modem (Cisco) and the modem works fine.

  The router also works very well I'm able to connect with my iPhone and IPad without any problem.

  But when I try to connect with my wireless laptop, it will only connect to Local access.    If I connect the laptop to the router with the ethernet cable, it works very well.

  It's a Dell Studio 15 with Vista.

  The computer is able to connect to wifi to other places without any problem, but for some reason that I can't connect home.   I tried to reset the modem and the router several times, but that did not help.   I tried the option repair & diagnose several times but it doesn't work.

  I tried to look for other solutions online and tried to disable IPv6, and while it helped some and I was able to connect wireless, the computer ran so slowly that it didn't seem like a good solution.

  This has been very frustrating.   Thanks in advance for any help or suggestion.
  Staci

  Hello Staciusa,

  Have you tried to change the wireless channel that your router is running at? There may be interference that could prevent the internet connection:

  Take a look at step 6 in this article that give more details about it:

  http://www.Microsoft.com/athome/Setup/wirelesstips.aspx

  If you need assistance to change the settings of the specific router, you will need to contact your router manufacturer or your internet service provider.

• Connection WRT54GL router Netgear modem.

  I am trying to connect a TV to the internet using a WRT54GL router and a NETGEAR DG834GT modem. I have configured the router by using the wizard, and I can connect to the router with my i phone or laptop. However the router does not appear in the available on Setup Netgear wireless networks, and it is not connecting to the lan either cable modem. Any help would be really appreciated.

  Thanks for the quick response. I'll do

• Router and Modem terms as device NAT Double - Solutions?

  Two questions I have about DSL/PPPoE

  (1) look in these forums, it is said that if you have a DSL modem, then you need to change your IP 192.168.2.1 could someone tell me why just for my own knowledge?

  (2) another question I have is what I use PPPoE if I have a DSL modem? Changing automatic DHCP to PPPoE willl solve my problem with my xbox not finding online games?

  (3) what I need to change my router in Bridge mode and is the same thing as mixed? If not how can I change due to bridge mode I've read that my router and modem are could act as a double NAT that could cause problems for the xbox?

  Any help would be welcome because I don't have any idea how to solve this

  Problem solved! Combination of mode Bridge and address static ip assigned to the xbox. Thank you guys

• Print server does not not with modem updated

  We have a LaserJet 1200 printer and have plugged into our modem and router with a HP Jetdirect 175 x print server.  Now, after updating the modem, it is more prints.  I have to reset the print server?  If so, how?  The new modem is a modem cable & wireless and router combined, Verizon DSL service, a model of Actiontec GT784WNV.  We use a Mac with OS 10.7.4 and other Mac on the network home.

  Thanks for any help!

  Ray

  > It says that my HP 175 x print server doesn't have a flash memory and firmware cannot be upgraded.

  > the final answer is that I need to replace the print server?

  I don't know that I see the link between the fact that you can't update the firmware and you are having problems with the configuration of your route on a Mac.

  I guess you have looked at the docs of print server?

  http://h20000.www2.HP.com/bizsupport/TechSupport/DocumentIndex.jsp?lang=en&cc=us&ContentType=SupportManual&prodTypeId=18972&prodSeriesId=28830

  http://bizsupport1.Austin.HP.com/BC/docs/support/SupportManual/bpj07493/bpj07493.PDF

  http://bizsupport1.Austin.HP.com/BC/docs/support/SupportManual/bpj07124/bpj07124.PDF

• Model of router with WPS

  Hi my TV a WPS button my router N300 model [WNR2200] has no WPS button. What router do I need to connect to broadband?

  Any router with a WPS option. Or use your router and enter the appropriate security settings.

• Access to the COR to two XP systems behind a router with a single public IP address

  Hello

  is it possible to access the RDC to two XP systems, with two different port for the DRC, behind a router with a single public IP address?

  Please note this ia a small home network without any parameters of the field. I use IP to access DRC.

  You comments are appreciated.

  Thank you

  Use different ports for the DRC on both XP and configure the router to redirect to the appropriate port on the appropriate computer.

  See the article in the Microsoft Knowledge Base How to change the listening port for remote desktop .

• Wired router with POE and Gigabit ethernet to run two AC1750 access points?

  Hello, I'm looking for a recommendation for a wired router with POE and Gigabit ethernet to connect to both access to ceiling LinkSys AC1750 points internet routing on the WAN to a Virgin Media UK cable connection plug - can someone advise a good solution?

  I'm a Home Office / Small Office so user there are several Wired's devices and a mixture of wireless clients. I need at least 8 ethernet outlets. Reliablity and speed performance are important, but not important enough to go overboard on the cost!

  Many thanks to you all.

  I recommend a router Linksys (SMB) LRT214\224 and a switch POE LGS Linksys (SMB). This combination will be very fast and stable.

• WRTP54G (wireless router with phone connection) with Panasonic BL-C30A network camera (WEP only)

  Hello

  I would use this wireless router with WEP I can access the wireless camera (camera does only WEP encryption).
  The camera should be the only device authorized to connect to this wireless router.
  I can devote channel 11, so only use this wireless router
  I know that WEP can be cracked but I think maybe I can set up the router for it does not matter, i.e.,.
  While the camera is accessible by this particular router

  so my questions are:
  1. can I configure the router so only local outgoing LAN requests http are allowed?
  2. any other suggestions about the configuration of router that prevent access to my network?
  (using address filtering (by address mac camera only) MAC is worth, but I guess that the MAC address can be spoofed so not a complete solution)

  Thank you
  Tom

  I think that 'toomanydonuts' has provided my solution in this thread:

  solution wire

  Thank you

  Tom

• Problems with my 4 port Gigabit Security Router with VPN

  OK, I got a wireless router and I have a Web site hosted by 1and1.com and I could connect my fine site. But recently I got the 4 port Gigabit Security Router with VPN and since then I have not been able to connect to it even, I started my own ftp server it always blocks and it will capture everything until she tries to recover the files, then it expires just after a while

  What is the model number of your device? If you have a Web server and an FTP server behind the router, you will need to transfer the ports used by the said request. Ports TCP 80 and TCP 21.